*
* Author: Timur Tabi <timur@freescale.com>
*
- * Copyright 2007 Freescale Semiconductor, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * Copyright 2007-2009 Freescale Semiconductor, Inc. This file is licensed
+ * under the terms of the GNU General Public License version 2. This
+ * program is licensed "as is" without any warranty of any kind, whether
+ * express or implied.
*
* This is an ASoC device driver for the Cirrus Logic CS4270 codec.
*
unsigned int mode; /* The mode (I2S or left-justified) */
};
-/*
- * Clock Ratio Selection for Master Mode with I2C enabled
+/**
+ * struct cs4270_mode_ratios - clock ratio tables
+ * @ratio: the ratio of MCLK to the sample rate
+ * @speed_mode: the Speed Mode bits to set in the Mode Control register for
+ * this ratio
+ * @mclk: the Ratio Select bits to set in the Mode Control register for this
+ * ratio
*
* The data for this chart is taken from Table 5 of the CS4270 reference
* manual.
* It is also used by cs4270_set_dai_sysclk() to tell ALSA which sampling
* rates the CS4270 currently supports.
*
- * Each element in this array corresponds to the ratios in mclk_ratios[].
- * These two arrays need to be in sync.
- *
- * 'speed_mode' is the corresponding bit pattern to be written to the
+ * @speed_mode is the corresponding bit pattern to be written to the
* MODE bits of the Mode Control Register
*
- * 'mclk' is the corresponding bit pattern to be wirten to the MCLK bits of
+ * @mclk is the corresponding bit pattern to be wirten to the MCLK bits of
* the Mode Control Register.
*
* In situations where a single ratio is represented by multiple speed
* modes, we favor the slowest speed. E.g, for a ratio of 128, we pick
* double-speed instead of quad-speed. However, the CS4270 errata states
- * that Divide-By-1.5 can cause failures, so we avoid that mode where
+ * that divide-By-1.5 can cause failures, so we avoid that mode where
* possible.
*
- * ERRATA: There is an errata for the CS4270 where divide-by-1.5 does not
- * work if VD = 3.3V. If this effects you, select the
+ * Errata: There is an errata for the CS4270 where divide-by-1.5 does not
+ * work if Vd is 3.3V. If this effects you, select the
* CONFIG_SND_SOC_CS4270_VD33_ERRATA Kconfig option, and the driver will
* never select any sample rates that require divide-by-1.5.
*/
-static struct {
+struct cs4270_mode_ratios {
unsigned int ratio;
u8 speed_mode;
u8 mclk;
-} cs4270_mode_ratios[] = {
+};
+
+static struct cs4270_mode_ratios[] = {
{64, CS4270_MODE_4X, CS4270_MODE_DIV1},
#ifndef CONFIG_SND_SOC_CS4270_VD33_ERRATA
{96, CS4270_MODE_4X, CS4270_MODE_DIV15},
/* The number of MCLK/LRCK ratios supported by the CS4270 */
#define NUM_MCLK_RATIOS ARRAY_SIZE(cs4270_mode_ratios)
-/*
- * Determine the CS4270 samples rates.
+/**
+ * cs4270_set_dai_sysclk - determine the CS4270 samples rates.
+ * @codec_dai: the codec DAI
+ * @clk_id: the clock ID (ignored)
+ * @freq: the MCLK input frequency
+ * @dir: the clock direction (ignored)
*
- * 'freq' is the input frequency to MCLK. The other parameters are ignored.
+ * This function is used to tell the codec driver what the input MCLK
+ * frequency is.
*
* The value of MCLK is used to determine which sample rates are supported
* by the CS4270. The ratio of MCLK / Fs must be equal to one of nine
- * support values: 64, 96, 128, 192, 256, 384, 512, 768, and 1024.
+ * supported values - 64, 96, 128, 192, 256, 384, 512, 768, and 1024.
*
* This function calculates the nine ratios and determines which ones match
* a standard sample rate. If there's a match, then it is added to the list
- * of support sample rates.
+ * of supported sample rates.
*
* This function must be called by the machine driver's 'startup' function,
* otherwise the list of supported sample rates will not be available in
* time for ALSA.
- *
- * Note that in stand-alone mode, the sample rate is determined by input
- * pins M0, M1, MDIV1, and MDIV2. Also in stand-alone mode, divide-by-3
- * is not a programmable option. However, divide-by-3 is not an available
- * option in stand-alone mode. This cases two problems: a ratio of 768 is
- * not available (it requires divide-by-3) and B) ratios 192 and 384 can
- * only be selected with divide-by-1.5, but there is an errate that make
- * this selection difficult.
- *
- * In addition, there is no mechanism for communicating with the machine
- * driver what the input settings can be. This would need to be implemented
- * for stand-alone mode to work.
*/
static int cs4270_set_dai_sysclk(struct snd_soc_dai *codec_dai,
int clk_id, unsigned int freq, int dir)
return 0;
}
-/*
- * Configure the codec for the selected audio format
+/**
+ * cs4270_set_dai_fmt - configure the codec for the selected audio format
+ * @codec_dai: the codec DAI
+ * @format: a SND_SOC_DAIFMT_x value indicating the data format
*
* This function takes a bitmask of SND_SOC_DAIFMT_x bits and programs the
* codec accordingly.
return ret;
}
-/*
- * Pre-fill the CS4270 register cache.
+/**
+ * cs4270_fill_cache - pre-fill the CS4270 register cache.
+ * @codec: the codec for this CS4270
+ *
+ * This function fills in the CS4270 register cache by reading the register
+ * values from the hardware.
+ *
+ * This CS4270 registers are cached to avoid excessive I2C I/O operations.
+ * After the initial read to pre-fill the cache, the CS4270 never updates
+ * the register values, so we won't have a cache coherency problem.
*
* We use the auto-increment feature of the CS4270 to read all registers in
* one shot.
return 0;
}
-/*
- * Read from the CS4270 register cache.
+/**
+ * cs4270_read_reg_cache - read from the CS4270 register cache.
+ * @codec: the codec for this CS4270
+ * @reg: the register to read
+ *
+ * This function returns the value for a given register. It reads only from
+ * the register cache, not the hardware itself.
*
* This CS4270 registers are cached to avoid excessive I2C I/O operations.
* After the initial read to pre-fill the cache, the CS4270 never updates
- * the register values, so we won't have a cache coherncy problem.
+ * the register values, so we won't have a cache coherency problem.
*/
static unsigned int cs4270_read_reg_cache(struct snd_soc_codec *codec,
unsigned int reg)
return cache[reg - CS4270_FIRSTREG];
}
-/*
- * Write to a CS4270 register via the I2C bus.
+/**
+ * cs4270_i2c_write - write to a CS4270 register via the I2C bus.
+ * @codec: the codec for this CS4270
+ * @reg: the register to write
+ * @value: the value to write to the register
*
* This function writes the given value to the given CS4270 register, and
* also updates the register cache.
return 0;
}
-/*
- * Program the CS4270 with the given hardware parameters.
+/**
+ * cs4270_hw_params - program the CS4270 with the given hardware parameters.
+ * @substream: the audio stream
+ * @params: the hardware parameters to set
+ * @dai: the SOC DAI (ignored)
*
- * The .ops functions are used to provide board-specific data, like
- * input frequencies, to this driver. This function takes that information,
+ * This function programs the hardware with the values provided.
+ * Specifically, the sample rate and the data format.
+ *
+ * The .ops functions are used to provide board-specific data, like input
+ * frequencies, to this driver. This function takes that information,
* combines it with the hardware parameters provided, and programs the
* hardware accordingly.
*/
}
#ifdef CONFIG_SND_SOC_CS4270_HWMUTE
-/*
- * Set the CS4270 external mute
+/**
+ * cs4270_mute - enable/disable the CS4270 external mute
+ * @dai: the SOC DAI
+ * @mute: 0 = disable mute, 1 = enable mute
*
* This function toggles the mute bits in the MUTE register. The CS4270's
* mute capability is intended for external muting circuitry, so if the
};
/*
- * Global variable to store codec for the ASoC probe function.
+ * cs4270_codec - global variable to store codec for the ASoC probe function
*
* If struct i2c_driver had a private_data field, we wouldn't need to use
* cs4270_codec. This is the only way to pass the codec structure from
};
EXPORT_SYMBOL_GPL(cs4270_dai);
-/*
- * ASoC probe function
+/**
+ * cs4270_probe - ASoC probe function
+ * @pdev: platform device
+ *
+ * This function is called when ASoC has all the pieces it needs to
+ * instantiate a sound driver.
*/
static int cs4270_probe(struct platform_device *pdev)
{
return ret;
}
+/**
+ * cs4270_remove - ASoC remove function
+ * @pdev: platform device
+ *
+ * This function is the counterpart to cs4270_probe().
+ */
static int cs4270_remove(struct platform_device *pdev)
{
struct snd_soc_device *socdev = platform_get_drvdata(pdev);
return 0;
};
-/*
- * Initialize the I2C interface of the CS4270
- *
- * This function is called for whenever the I2C subsystem finds a device
- * at a particular address.
+/**
+ * cs4270_i2c_probe - initialize the I2C interface of the CS4270
+ * @i2c_client: the I2C client object
+ * @id: the I2C device ID (ignored)
*
- * Note: snd_soc_new_pcms() must be called before this function can be called,
- * because of snd_ctl_add().
+ * This function is called whenever the I2C subsystem finds a device that
+ * matches the device ID given via a prior call to i2c_add_driver().
*/
static int cs4270_i2c_probe(struct i2c_client *i2c_client,
const struct i2c_device_id *id)
return ret;
}
+/**
+ * cs4270_i2c_remove - remove an I2C device
+ * @i2c_client: the I2C client object
+ *
+ * This function is the counterpart to cs4270_i2c_probe().
+ */
static int cs4270_i2c_remove(struct i2c_client *i2c_client)
{
struct cs4270_private *cs4270 = i2c_get_clientdata(i2c_client);
return 0;
}
+/*
+ * cs4270_id - I2C device IDs supported by this driver
+ */
static struct i2c_device_id cs4270_id[] = {
{"cs4270", 0},
{}
};
MODULE_DEVICE_TABLE(i2c, cs4270_id);
+/*
+ * cs4270_i2c_driver - I2C device identification
+ *
+ * This structure tells the I2C subsystem how to identify and support a
+ * given I2C device type.
+ */
static struct i2c_driver cs4270_i2c_driver = {
.driver = {
.name = "cs4270",
projects / linux-2.6-omap-h63xx.git / commitdiff