]> pilppa.com Git - linux-2.6-omap-h63xx.git/commitdiff
V4L/DVB (6190): cx23885: GPIO fix for non HVR1800lp boards
authorSteven Toth <stoth@hauppauge.com>
Sat, 8 Sep 2007 22:08:17 +0000 (19:08 -0300)
committerMauro Carvalho Chehab <mchehab@infradead.org>
Wed, 10 Oct 2007 01:14:27 +0000 (22:14 -0300)
The HVR1250 and HVR1800 boards need the s5h1409 demod GPIO enabled.

Signed-off-by: Steven Toth <stoth@hauppauge.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/cx23885/cx23885-dvb.c

index 291cc055622298a418581fc53b1c41d9e74fc18a..ffa4c49d691671f5aeda02be74dac54ed8ca1872 100644 (file)
@@ -80,6 +80,15 @@ static struct videobuf_queue_ops dvb_qops = {
 };
 
 static struct s5h1409_config hauppauge_generic_config = {
+       .demod_address = 0x32 >> 1,
+       .output_mode   = S5H1409_SERIAL_OUTPUT,
+       .gpio          = S5H1409_GPIO_ON,
+       .if_freq       = 44000,
+       .inversion     = S5H1409_INVERSION_OFF,
+       .status_mode   = S5H1409_DEMODLOCKING
+};
+
+static struct s5h1409_config hauppauge_hvr1800lp_config = {
        .demod_address = 0x32 >> 1,
        .output_mode   = S5H1409_SERIAL_OUTPUT,
        .gpio          = S5H1409_GPIO_OFF,
@@ -103,7 +112,6 @@ static int dvb_register(struct cx23885_tsport *port)
        switch (dev->board) {
        case CX23885_BOARD_HAUPPAUGE_HVR1250:
        case CX23885_BOARD_HAUPPAUGE_HVR1800:
-       case CX23885_BOARD_HAUPPAUGE_HVR1800lp:
                port->dvb.frontend = dvb_attach(s5h1409_attach,
                                                &hauppauge_generic_config,
                                                &dev->i2c_bus[0].i2c_adap);
@@ -113,6 +121,16 @@ static int dvb_register(struct cx23885_tsport *port)
                                   &hauppauge_generic_tunerconfig, 0);
                }
                break;
+       case CX23885_BOARD_HAUPPAUGE_HVR1800lp:
+               port->dvb.frontend = dvb_attach(s5h1409_attach,
+                                               &hauppauge_hvr1800lp_config,
+                                               &dev->i2c_bus[0].i2c_adap);
+               if (port->dvb.frontend != NULL) {
+                       dvb_attach(mt2131_attach, port->dvb.frontend,
+                                  &dev->i2c_bus[0].i2c_adap,
+                                  &hauppauge_generic_tunerconfig, 0);
+               }
+               break;
        default:
                printk("%s: The frontend of your DVB/ATSC card isn't supported yet\n",
                       dev->name);