p) Freescale Synchronous Serial Interface
q) USB EHCI controllers
- VII - Specifying interrupt information for devices
+ VII - Marvell Discovery mv64[345]6x System Controller chips
+ 1) The /system-controller node
+ 2) Child nodes of /system-controller
+ a) Marvell Discovery MDIO bus
+ b) Marvell Discovery ethernet controller
+ c) Marvell Discovery PHY nodes
+ d) Marvell Discovery SDMA nodes
+ e) Marvell Discovery BRG nodes
+ f) Marvell Discovery CUNIT nodes
+ g) Marvell Discovery MPSCROUTING nodes
+ h) Marvell Discovery MPSCINTR nodes
+ i) Marvell Discovery MPSC nodes
+ j) Marvell Discovery Watch Dog Timer nodes
+ k) Marvell Discovery I2C nodes
+ l) Marvell Discovery PIC (Programmable Interrupt Controller) nodes
+ m) Marvell Discovery MPP (Multipurpose Pins) multiplexing nodes
+ n) Marvell Discovery GPP (General Purpose Pins) nodes
+ o) Marvell Discovery PCI host bridge node
+ p) Marvell Discovery CPU Error nodes
+ q) Marvell Discovery SRAM Controller nodes
+ r) Marvell Discovery PCI Error Handler nodes
+ s) Marvell Discovery Memory Controller nodes
+
+ VIII - Specifying interrupt information for devices
1) interrupts property
2) interrupt-parent property
3) OpenPIC Interrupt Controllers
};
- More devices will be defined as this spec matures.
+VII - Marvell Discovery mv64[345]6x System Controller chips
+===========================================================
-VII - Specifying interrupt information for devices
+The Marvell mv64[345]60 series of system controller chips contain
+many of the peripherals needed to implement a complete computer
+system. In this section, we define device tree nodes to describe
+the system controller chip itself and each of the peripherals
+which it contains. Compatible string values for each node are
+prefixed with the string "marvell,", for Marvell Technology Group Ltd.
+
+1) The /system-controller node
+
+ This node is used to represent the system-controller and must be
+ present when the system uses a system contller chip. The top-level
+ system-controller node contains information that is global to all
+ devices within the system controller chip. The node name begins
+ with "system-controller" followed by the unit address, which is
+ the base address of the memory-mapped register set for the system
+ controller chip.
+
+ Required properties:
+
+ - ranges : Describes the translation of system controller addresses
+ for memory mapped registers.
+ - clock-frequency: Contains the main clock frequency for the system
+ controller chip.
+ - reg : This property defines the address and size of the
+ memory-mapped registers contained within the system controller
+ chip. The address specified in the "reg" property should match
+ the unit address of the system-controller node.
+ - #address-cells : Address representation for system controller
+ devices. This field represents the number of cells needed to
+ represent the address of the memory-mapped registers of devices
+ within the system controller chip.
+ - #size-cells : Size representation for for the memory-mapped
+ registers within the system controller chip.
+ - #interrupt-cells : Defines the width of cells used to represent
+ interrupts.
+
+ Optional properties:
+
+ - model : The specific model of the system controller chip. Such
+ as, "mv64360", "mv64460", or "mv64560".
+ - compatible : A string identifying the compatibility identifiers
+ of the system controller chip.
+
+ The system-controller node contains child nodes for each system
+ controller device that the platform uses. Nodes should not be created
+ for devices which exist on the system controller chip but are not used
+
+ Example Marvell Discovery mv64360 system-controller node:
+
+ system-controller@f1000000 { /* Marvell Discovery mv64360 */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ model = "mv64360"; /* Default */
+ compatible = "marvell,mv64360";
+ clock-frequency = <133333333>;
+ reg = <0xf1000000 0x10000>;
+ virtual-reg = <0xf1000000>;
+ ranges = <0x88000000 0x88000000 0x1000000 /* PCI 0 I/O Space */
+ 0x80000000 0x80000000 0x8000000 /* PCI 0 MEM Space */
+ 0xa0000000 0xa0000000 0x4000000 /* User FLASH */
+ 0x00000000 0xf1000000 0x0010000 /* Bridge's regs */
+ 0xf2000000 0xf2000000 0x0040000>;/* Integrated SRAM */
+
+ [ child node definitions... ]
+ }
+
+2) Child nodes of /system-controller
+
+ a) Marvell Discovery MDIO bus
+
+ The MDIO is a bus to which the PHY devices are connected. For each
+ device that exists on this bus, a child node should be created. See
+ the definition of the PHY node below for an example of how to define
+ a PHY.
+
+ Required properties:
+ - #address-cells : Should be <1>
+ - #size-cells : Should be <0>
+ - device_type : Should be "mdio"
+ - compatible : Should be "marvell,mv64360-mdio"
+
+ Example:
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ device_type = "mdio";
+ compatible = "marvell,mv64360-mdio";
+
+ ethernet-phy@0 {
+ ......
+ };
+ };
+
+
+ b) Marvell Discovery ethernet controller
+
+ The Discover ethernet controller is described with two levels
+ of nodes. The first level describes an ethernet silicon block
+ and the second level describes up to 3 ethernet nodes within
+ that block. The reason for the multiple levels is that the
+ registers for the node are interleaved within a single set
+ of registers. The "ethernet-block" level describes the
+ shared register set, and the "ethernet" nodes describe ethernet
+ port-specific properties.
+
+ Ethernet block node
+
+ Required properties:
+ - #address-cells : <1>
+ - #size-cells : <0>
+ - compatible : "marvell,mv64360-eth-block"
+ - reg : Offset and length of the register set for this block
+
+ Example Discovery Ethernet block node:
+ ethernet-block@2000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "marvell,mv64360-eth-block";
+ reg = <0x2000 0x2000>;
+ ethernet@0 {
+ .......
+ };
+ };
+
+ Ethernet port node
+
+ Required properties:
+ - device_type : Should be "network".
+ - compatible : Should be "marvell,mv64360-eth".
+ - reg : Should be <0>, <1>, or <2>, according to which registers
+ within the silicon block the device uses.
+ - interrupts : <a> where a is the interrupt number for the port.
+ - interrupt-parent : the phandle for the interrupt controller
+ that services interrupts for this device.
+ - phy : the phandle for the PHY connected to this ethernet
+ controller.
+ - local-mac-address : 6 bytes, MAC address
+
+ Example Discovery Ethernet port node:
+ ethernet@0 {
+ device_type = "network";
+ compatible = "marvell,mv64360-eth";
+ reg = <0>;
+ interrupts = <32>;
+ interrupt-parent = <&PIC>;
+ phy = <&PHY0>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+
+
+
+ c) Marvell Discovery PHY nodes
+
+ Required properties:
+ - device_type : Should be "ethernet-phy"
+ - interrupts : <a> where a is the interrupt number for this phy.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+ - reg : The ID number for the phy, usually a small integer
+
+ Example Discovery PHY node:
+ ethernet-phy@1 {
+ device_type = "ethernet-phy";
+ compatible = "broadcom,bcm5421";
+ interrupts = <76>; /* GPP 12 */
+ interrupt-parent = <&PIC>;
+ reg = <1>;
+ };
+
+
+ d) Marvell Discovery SDMA nodes
+
+ Represent DMA hardware associated with the MPSC (multiprotocol
+ serial controllers).
+
+ Required properties:
+ - compatible : "marvell,mv64360-sdma"
+ - reg : Offset and length of the register set for this device
+ - interrupts : <a> where a is the interrupt number for the DMA
+ device.
+ - interrupt-parent : the phandle for the interrupt controller
+ that services interrupts for this device.
+
+ Example Discovery SDMA node:
+ sdma@4000 {
+ compatible = "marvell,mv64360-sdma";
+ reg = <0x4000 0xc18>;
+ virtual-reg = <0xf1004000>;
+ interrupts = <36>;
+ interrupt-parent = <&PIC>;
+ };
+
+
+ e) Marvell Discovery BRG nodes
+
+ Represent baud rate generator hardware associated with the MPSC
+ (multiprotocol serial controllers).
+
+ Required properties:
+ - compatible : "marvell,mv64360-brg"
+ - reg : Offset and length of the register set for this device
+ - clock-src : A value from 0 to 15 which selects the clock
+ source for the baud rate generator. This value corresponds
+ to the CLKS value in the BRGx configuration register. See
+ the mv64x60 User's Manual.
+ - clock-frequence : The frequency (in Hz) of the baud rate
+ generator's input clock.
+ - current-speed : The current speed setting (presumably by
+ firmware) of the baud rate generator.
+
+ Example Discovery BRG node:
+ brg@b200 {
+ compatible = "marvell,mv64360-brg";
+ reg = <0xb200 0x8>;
+ clock-src = <8>;
+ clock-frequency = <133333333>;
+ current-speed = <9600>;
+ };
+
+
+ f) Marvell Discovery CUNIT nodes
+
+ Represent the Serial Communications Unit device hardware.
+
+ Required properties:
+ - reg : Offset and length of the register set for this device
+
+ Example Discovery CUNIT node:
+ cunit@f200 {
+ reg = <0xf200 0x200>;
+ };
+
+
+ g) Marvell Discovery MPSCROUTING nodes
+
+ Represent the Discovery's MPSC routing hardware
+
+ Required properties:
+ - reg : Offset and length of the register set for this device
+
+ Example Discovery CUNIT node:
+ mpscrouting@b500 {
+ reg = <0xb400 0xc>;
+ };
+
+
+ h) Marvell Discovery MPSCINTR nodes
+
+ Represent the Discovery's MPSC DMA interrupt hardware registers
+ (SDMA cause and mask registers).
+
+ Required properties:
+ - reg : Offset and length of the register set for this device
+
+ Example Discovery MPSCINTR node:
+ mpsintr@b800 {
+ reg = <0xb800 0x100>;
+ };
+
+
+ i) Marvell Discovery MPSC nodes
+
+ Represent the Discovery's MPSC (Multiprotocol Serial Controller)
+ serial port.
+
+ Required properties:
+ - device_type : "serial"
+ - compatible : "marvell,mv64360-mpsc"
+ - reg : Offset and length of the register set for this device
+ - sdma : the phandle for the SDMA node used by this port
+ - brg : the phandle for the BRG node used by this port
+ - cunit : the phandle for the CUNIT node used by this port
+ - mpscrouting : the phandle for the MPSCROUTING node used by this port
+ - mpscintr : the phandle for the MPSCINTR node used by this port
+ - cell-index : the hardware index of this cell in the MPSC core
+ - max_idle : value needed for MPSC CHR3 (Maximum Frame Length)
+ register
+ - interrupts : <a> where a is the interrupt number for the MPSC.
+ - interrupt-parent : the phandle for the interrupt controller
+ that services interrupts for this device.
+
+ Example Discovery MPSCINTR node:
+ mpsc@8000 {
+ device_type = "serial";
+ compatible = "marvell,mv64360-mpsc";
+ reg = <0x8000 0x38>;
+ virtual-reg = <0xf1008000>;
+ sdma = <&SDMA0>;
+ brg = <&BRG0>;
+ cunit = <&CUNIT>;
+ mpscrouting = <&MPSCROUTING>;
+ mpscintr = <&MPSCINTR>;
+ cell-index = <0>;
+ max_idle = <40>;
+ interrupts = <40>;
+ interrupt-parent = <&PIC>;
+ };
+
+
+ j) Marvell Discovery Watch Dog Timer nodes
+
+ Represent the Discovery's watchdog timer hardware
+
+ Required properties:
+ - compatible : "marvell,mv64360-wdt"
+ - reg : Offset and length of the register set for this device
+
+ Example Discovery Watch Dog Timer node:
+ wdt@b410 {
+ compatible = "marvell,mv64360-wdt";
+ reg = <0xb410 0x8>;
+ };
+
+
+ k) Marvell Discovery I2C nodes
+
+ Represent the Discovery's I2C hardware
+
+ Required properties:
+ - device_type : "i2c"
+ - compatible : "marvell,mv64360-i2c"
+ - reg : Offset and length of the register set for this device
+ - interrupts : <a> where a is the interrupt number for the I2C.
+ - interrupt-parent : the phandle for the interrupt controller
+ that services interrupts for this device.
+
+ Example Discovery I2C node:
+ compatible = "marvell,mv64360-i2c";
+ reg = <0xc000 0x20>;
+ virtual-reg = <0xf100c000>;
+ interrupts = <37>;
+ interrupt-parent = <&PIC>;
+ };
+
+
+ l) Marvell Discovery PIC (Programmable Interrupt Controller) nodes
+
+ Represent the Discovery's PIC hardware
+
+ Required properties:
+ - #interrupt-cells : <1>
+ - #address-cells : <0>
+ - compatible : "marvell,mv64360-pic"
+ - reg : Offset and length of the register set for this device
+ - interrupt-controller
+
+ Example Discovery PIC node:
+ pic {
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ compatible = "marvell,mv64360-pic";
+ reg = <0x0 0x88>;
+ interrupt-controller;
+ };
+
+
+ m) Marvell Discovery MPP (Multipurpose Pins) multiplexing nodes
+
+ Represent the Discovery's MPP hardware
+
+ Required properties:
+ - compatible : "marvell,mv64360-mpp"
+ - reg : Offset and length of the register set for this device
+
+ Example Discovery MPP node:
+ mpp@f000 {
+ compatible = "marvell,mv64360-mpp";
+ reg = <0xf000 0x10>;
+ };
+
+
+ n) Marvell Discovery GPP (General Purpose Pins) nodes
+
+ Represent the Discovery's GPP hardware
+
+ Required properties:
+ - compatible : "marvell,mv64360-gpp"
+ - reg : Offset and length of the register set for this device
+
+ Example Discovery GPP node:
+ gpp@f000 {
+ compatible = "marvell,mv64360-gpp";
+ reg = <0xf100 0x20>;
+ };
+
+
+ o) Marvell Discovery PCI host bridge node
+
+ Represents the Discovery's PCI host bridge device. The properties
+ for this node conform to Rev 2.1 of the PCI Bus Binding to IEEE
+ 1275-1994. A typical value for the compatible property is
+ "marvell,mv64360-pci".
+
+ Example Discovery PCI host bridge node
+ pci@80000000 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pci";
+ compatible = "marvell,mv64360-pci";
+ reg = <0xcf8 0x8>;
+ ranges = <0x01000000 0x0 0x0
+ 0x88000000 0x0 0x01000000
+ 0x02000000 0x0 0x80000000
+ 0x80000000 0x0 0x08000000>;
+ bus-range = <0 255>;
+ clock-frequency = <66000000>;
+ interrupt-parent = <&PIC>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+ interrupt-map = <
+ /* IDSEL 0x0a */
+ 0x5000 0 0 1 &PIC 80
+ 0x5000 0 0 2 &PIC 81
+ 0x5000 0 0 3 &PIC 91
+ 0x5000 0 0 4 &PIC 93
+
+ /* IDSEL 0x0b */
+ 0x5800 0 0 1 &PIC 91
+ 0x5800 0 0 2 &PIC 93
+ 0x5800 0 0 3 &PIC 80
+ 0x5800 0 0 4 &PIC 81
+
+ /* IDSEL 0x0c */
+ 0x6000 0 0 1 &PIC 91
+ 0x6000 0 0 2 &PIC 93
+ 0x6000 0 0 3 &PIC 80
+ 0x6000 0 0 4 &PIC 81
+
+ /* IDSEL 0x0d */
+ 0x6800 0 0 1 &PIC 93
+ 0x6800 0 0 2 &PIC 80
+ 0x6800 0 0 3 &PIC 81
+ 0x6800 0 0 4 &PIC 91
+ >;
+ };
+
+
+ p) Marvell Discovery CPU Error nodes
+
+ Represent the Discovery's CPU error handler device.
+
+ Required properties:
+ - compatible : "marvell,mv64360-cpu-error"
+ - reg : Offset and length of the register set for this device
+ - interrupts : the interrupt number for this device
+ - interrupt-parent : the phandle for the interrupt controller
+ that services interrupts for this device.
+
+ Example Discovery CPU Error node:
+ cpu-error@0070 {
+ compatible = "marvell,mv64360-cpu-error";
+ reg = <0x70 0x10 0x128 0x28>;
+ interrupts = <3>;
+ interrupt-parent = <&PIC>;
+ };
+
+
+ q) Marvell Discovery SRAM Controller nodes
+
+ Represent the Discovery's SRAM controller device.
+
+ Required properties:
+ - compatible : "marvell,mv64360-sram-ctrl"
+ - reg : Offset and length of the register set for this device
+ - interrupts : the interrupt number for this device
+ - interrupt-parent : the phandle for the interrupt controller
+ that services interrupts for this device.
+
+ Example Discovery SRAM Controller node:
+ sram-ctrl@0380 {
+ compatible = "marvell,mv64360-sram-ctrl";
+ reg = <0x380 0x80>;
+ interrupts = <13>;
+ interrupt-parent = <&PIC>;
+ };
+
+
+ r) Marvell Discovery PCI Error Handler nodes
+
+ Represent the Discovery's PCI error handler device.
+
+ Required properties:
+ - compatible : "marvell,mv64360-pci-error"
+ - reg : Offset and length of the register set for this device
+ - interrupts : the interrupt number for this device
+ - interrupt-parent : the phandle for the interrupt controller
+ that services interrupts for this device.
+
+ Example Discovery PCI Error Handler node:
+ pci-error@1d40 {
+ compatible = "marvell,mv64360-pci-error";
+ reg = <0x1d40 0x40 0xc28 0x4>;
+ interrupts = <12>;
+ interrupt-parent = <&PIC>;
+ };
+
+
+ s) Marvell Discovery Memory Controller nodes
+
+ Represent the Discovery's memory controller device.
+
+ Required properties:
+ - compatible : "marvell,mv64360-mem-ctrl"
+ - reg : Offset and length of the register set for this device
+ - interrupts : the interrupt number for this device
+ - interrupt-parent : the phandle for the interrupt controller
+ that services interrupts for this device.
+
+ Example Discovery Memory Controller node:
+ mem-ctrl@1400 {
+ compatible = "marvell,mv64360-mem-ctrl";
+ reg = <0x1400 0x60>;
+ interrupts = <17>;
+ interrupt-parent = <&PIC>;
+ };
+
+
+VIII - Specifying interrupt information for devices
===================================================
The device tree represents the busses and devices of a hardware
projects / linux-2.6-omap-h63xx.git / commitdiff