}
}
+static int ata_dev_set_dipm(struct ata_device *dev, enum link_pm policy)
+{
+ struct ata_link *link = dev->link;
+ struct ata_port *ap = link->ap;
+ u32 scontrol;
+ unsigned int err_mask;
+ int rc;
+
+ /*
+ * disallow DIPM for drivers which haven't set
+ * ATA_FLAG_IPM. This is because when DIPM is enabled,
+ * phy ready will be set in the interrupt status on
+ * state changes, which will cause some drivers to
+ * think there are errors - additionally drivers will
+ * need to disable hot plug.
+ */
+ if (!(ap->flags & ATA_FLAG_IPM) || !ata_dev_enabled(dev)) {
+ ap->pm_policy = NOT_AVAILABLE;
+ return -EINVAL;
+ }
+
+ /*
+ * For DIPM, we will only enable it for the
+ * min_power setting.
+ *
+ * Why? Because Disks are too stupid to know that
+ * If the host rejects a request to go to SLUMBER
+ * they should retry at PARTIAL, and instead it
+ * just would give up. So, for medium_power to
+ * work at all, we need to only allow HIPM.
+ */
+ rc = sata_scr_read(link, SCR_CONTROL, &scontrol);
+ if (rc)
+ return rc;
+
+ switch (policy) {
+ case MIN_POWER:
+ /* no restrictions on IPM transitions */
+ scontrol &= ~(0x3 << 8);
+ rc = sata_scr_write(link, SCR_CONTROL, scontrol);
+ if (rc)
+ return rc;
+
+ /* enable DIPM */
+ if (dev->flags & ATA_DFLAG_DIPM)
+ err_mask = ata_dev_set_feature(dev,
+ SETFEATURES_SATA_ENABLE, SATA_DIPM);
+ break;
+ case MEDIUM_POWER:
+ /* allow IPM to PARTIAL */
+ scontrol &= ~(0x1 << 8);
+ scontrol |= (0x2 << 8);
+ rc = sata_scr_write(link, SCR_CONTROL, scontrol);
+ if (rc)
+ return rc;
+
+ /* disable DIPM */
+ if (ata_dev_enabled(dev) && (dev->flags & ATA_DFLAG_DIPM))
+ err_mask = ata_dev_set_feature(dev,
+ SETFEATURES_SATA_DISABLE, SATA_DIPM);
+ break;
+ case NOT_AVAILABLE:
+ case MAX_PERFORMANCE:
+ /* disable all IPM transitions */
+ scontrol |= (0x3 << 8);
+ rc = sata_scr_write(link, SCR_CONTROL, scontrol);
+ if (rc)
+ return rc;
+
+ /* disable DIPM */
+ if (ata_dev_enabled(dev) && (dev->flags & ATA_DFLAG_DIPM))
+ err_mask = ata_dev_set_feature(dev,
+ SETFEATURES_SATA_DISABLE, SATA_DIPM);
+ break;
+ }
+
+ /* FIXME: handle SET FEATURES failure */
+ (void) err_mask;
+
+ return 0;
+}
+
+/**
+ * ata_dev_enable_pm - enable SATA interface power management
+ * @device - device to enable ipm for
+ * @policy - the link power management policy
+ *
+ * Enable SATA Interface power management. This will enable
+ * Device Interface Power Management (DIPM) for min_power
+ * policy, and then call driver specific callbacks for
+ * enabling Host Initiated Power management.
+ *
+ * Locking: Caller.
+ * Returns: -EINVAL if IPM is not supported, 0 otherwise.
+ */
+void ata_dev_enable_pm(struct ata_device *dev, enum link_pm policy)
+{
+ int rc = 0;
+ struct ata_port *ap = dev->link->ap;
+
+ /* set HIPM first, then DIPM */
+ if (ap->ops->enable_pm)
+ rc = ap->ops->enable_pm(ap, policy);
+ if (rc)
+ goto enable_pm_out;
+ rc = ata_dev_set_dipm(dev, policy);
+
+enable_pm_out:
+ if (rc)
+ ap->pm_policy = MAX_PERFORMANCE;
+ else
+ ap->pm_policy = policy;
+ return /* rc */; /* hopefully we can use 'rc' eventually */
+}
+
+/**
+ * ata_dev_disable_pm - disable SATA interface power management
+ * @device - device to enable ipm for
+ *
+ * Disable SATA Interface power management. This will disable
+ * Device Interface Power Management (DIPM) without changing
+ * policy, call driver specific callbacks for disabling Host
+ * Initiated Power management.
+ *
+ * Locking: Caller.
+ * Returns: void
+ */
+static void ata_dev_disable_pm(struct ata_device *dev)
+{
+ struct ata_port *ap = dev->link->ap;
+
+ ata_dev_set_dipm(dev, MAX_PERFORMANCE);
+ if (ap->ops->disable_pm)
+ ap->ops->disable_pm(ap);
+}
+
+void ata_lpm_schedule(struct ata_port *ap, enum link_pm policy)
+{
+ ap->pm_policy = policy;
+ ap->link.eh_info.action |= ATA_EHI_LPM;
+ ap->link.eh_info.flags |= ATA_EHI_NO_AUTOPSY;
+ ata_port_schedule_eh(ap);
+}
+
+static void ata_lpm_enable(struct ata_host *host)
+{
+ struct ata_link *link;
+ struct ata_port *ap;
+ struct ata_device *dev;
+ int i;
+
+ for (i = 0; i < host->n_ports; i++) {
+ ap = host->ports[i];
+ ata_port_for_each_link(link, ap) {
+ ata_link_for_each_dev(dev, link)
+ ata_dev_disable_pm(dev);
+ }
+ }
+}
+
+static void ata_lpm_disable(struct ata_host *host)
+{
+ int i;
+
+ for (i = 0; i < host->n_ports; i++) {
+ struct ata_port *ap = host->ports[i];
+ ata_lpm_schedule(ap, ap->pm_policy);
+ }
+}
+
+
/**
* ata_devchk - PATA device presence detection
* @ap: ATA channel to examine
if (dev->flags & ATA_DFLAG_LBA48)
dev->max_sectors = ATA_MAX_SECTORS_LBA48;
+ if (!(dev->horkage & ATA_HORKAGE_IPM)) {
+ if (ata_id_has_hipm(dev->id))
+ dev->flags |= ATA_DFLAG_HIPM;
+ if (ata_id_has_dipm(dev->id))
+ dev->flags |= ATA_DFLAG_DIPM;
+ }
+
if (dev->horkage & ATA_HORKAGE_DIAGNOSTIC) {
/* Let the user know. We don't want to disallow opens for
rescue purposes, or in case the vendor is just a blithering
dev->max_sectors = min_t(unsigned int, ATA_MAX_SECTORS_128,
dev->max_sectors);
+ if (ata_dev_blacklisted(dev) & ATA_HORKAGE_IPM) {
+ dev->horkage |= ATA_HORKAGE_IPM;
+
+ /* reset link pm_policy for this port to no pm */
+ ap->pm_policy = MAX_PERFORMANCE;
+ }
+
if (ap->ops->dev_config)
ap->ops->dev_config(dev);
{
int rc;
+ /*
+ * disable link pm on all ports before requesting
+ * any pm activity
+ */
+ ata_lpm_enable(host);
+
rc = ata_host_request_pm(host, mesg, 0, ATA_EHI_QUIET, 1);
if (rc == 0)
host->dev->power.power_state = mesg;
ata_host_request_pm(host, PMSG_ON, ATA_EH_SOFTRESET,
ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET, 0);
host->dev->power.power_state = PMSG_ON;
+
+ /* reenable link pm */
+ ata_lpm_disable(host);
}
#endif
struct ata_port *ap = host->ports[i];
ata_scsi_scan_host(ap, 1);
+ ata_lpm_schedule(ap, ap->pm_policy);
}
return 0;
* likely to change as new drivers are added and updated.
* Do not depend on ABI/API stability.
*/
-
EXPORT_SYMBOL_GPL(sata_deb_timing_normal);
EXPORT_SYMBOL_GPL(sata_deb_timing_hotplug);
EXPORT_SYMBOL_GPL(sata_deb_timing_long);
};
+static const struct {
+ enum link_pm value;
+ const char *name;
+} link_pm_policy[] = {
+ { NOT_AVAILABLE, "max_performance" },
+ { MIN_POWER, "min_power" },
+ { MAX_PERFORMANCE, "max_performance" },
+ { MEDIUM_POWER, "medium_power" },
+};
+
+const char *ata_scsi_lpm_get(enum link_pm policy)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(link_pm_policy); i++)
+ if (link_pm_policy[i].value == policy)
+ return link_pm_policy[i].name;
+
+ return NULL;
+}
+
+static ssize_t ata_scsi_lpm_put(struct class_device *class_dev,
+ const char *buf, size_t count)
+{
+ struct Scsi_Host *shost = class_to_shost(class_dev);
+ struct ata_port *ap = ata_shost_to_port(shost);
+ enum link_pm policy = 0;
+ int i;
+
+ /*
+ * we are skipping array location 0 on purpose - this
+ * is because a value of NOT_AVAILABLE is displayed
+ * to the user as max_performance, but when the user
+ * writes "max_performance", they actually want the
+ * value to match MAX_PERFORMANCE.
+ */
+ for (i = 1; i < ARRAY_SIZE(link_pm_policy); i++) {
+ const int len = strlen(link_pm_policy[i].name);
+ if (strncmp(link_pm_policy[i].name, buf, len) == 0 &&
+ buf[len] == '\n') {
+ policy = link_pm_policy[i].value;
+ break;
+ }
+ }
+ if (!policy)
+ return -EINVAL;
+
+ ata_lpm_schedule(ap, policy);
+ return count;
+}
+
+static ssize_t
+ata_scsi_lpm_show(struct class_device *class_dev, char *buf)
+{
+ struct Scsi_Host *shost = class_to_shost(class_dev);
+ struct ata_port *ap = ata_shost_to_port(shost);
+ const char *policy =
+ ata_scsi_lpm_get(ap->pm_policy);
+
+ if (!policy)
+ return -EINVAL;
+
+ return snprintf(buf, 23, "%s\n", policy);
+}
+CLASS_DEVICE_ATTR(link_power_management_policy, S_IRUGO | S_IWUSR,
+ ata_scsi_lpm_show, ata_scsi_lpm_put);
+EXPORT_SYMBOL_GPL(class_device_attr_link_power_management_policy);
+
static void ata_scsi_invalid_field(struct scsi_cmnd *cmd,
void (*done)(struct scsi_cmnd *))
{
ATA_DFLAG_ACPI_PENDING = (1 << 5), /* ACPI resume action pending */
ATA_DFLAG_ACPI_FAILED = (1 << 6), /* ACPI on devcfg has failed */
ATA_DFLAG_AN = (1 << 7), /* AN configured */
+ ATA_DFLAG_HIPM = (1 << 8), /* device supports HIPM */
+ ATA_DFLAG_DIPM = (1 << 9), /* device supports DIPM */
ATA_DFLAG_CFG_MASK = (1 << 12) - 1,
ATA_DFLAG_PIO = (1 << 12), /* device limited to PIO mode */
ATA_FLAG_ACPI_SATA = (1 << 17), /* need native SATA ACPI layout */
ATA_FLAG_AN = (1 << 18), /* controller supports AN */
ATA_FLAG_PMP = (1 << 19), /* controller supports PMP */
+ ATA_FLAG_IPM = (1 << 20), /* driver can handle IPM */
/* The following flag belongs to ap->pflags but is kept in
* ap->flags because it's referenced in many LLDs and will be
ATA_EHI_RESUME_LINK = (1 << 1), /* resume link (reset modifier) */
ATA_EHI_NO_AUTOPSY = (1 << 2), /* no autopsy */
ATA_EHI_QUIET = (1 << 3), /* be quiet */
+ ATA_EHI_LPM = (1 << 4), /* link power management action */
ATA_EHI_DID_SOFTRESET = (1 << 16), /* already soft-reset this port */
ATA_EHI_DID_HARDRESET = (1 << 17), /* already soft-reset this port */
ATA_HORKAGE_BROKEN_HPA = (1 << 4), /* Broken HPA */
ATA_HORKAGE_SKIP_PM = (1 << 5), /* Skip PM operations */
ATA_HORKAGE_HPA_SIZE = (1 << 6), /* native size off by one */
+ ATA_HORKAGE_IPM = (1 << 7), /* Link PM problems */
/* DMA mask for user DMA control: User visible values; DO NOT
renumber */
unsigned long deadline);
typedef void (*ata_postreset_fn_t)(struct ata_link *link, unsigned int *classes);
+/*
+ * host pm policy: If you alter this, you also need to alter libata-scsi.c
+ * (for the ascii descriptions)
+ */
+enum link_pm {
+ NOT_AVAILABLE,
+ MIN_POWER,
+ MAX_PERFORMANCE,
+ MEDIUM_POWER,
+};
+extern struct class_device_attribute class_device_attr_link_power_management_policy;
+
struct ata_ioports {
void __iomem *cmd_addr;
void __iomem *data_addr;
pm_message_t pm_mesg;
int *pm_result;
+ enum link_pm pm_policy;
struct timer_list fastdrain_timer;
unsigned long fastdrain_cnt;
int (*port_suspend) (struct ata_port *ap, pm_message_t mesg);
int (*port_resume) (struct ata_port *ap);
-
+ int (*enable_pm) (struct ata_port *ap, enum link_pm policy);
+ void (*disable_pm) (struct ata_port *ap);
int (*port_start) (struct ata_port *ap);
void (*port_stop) (struct ata_port *ap);
projects / linux-2.6-omap-h63xx.git / commitdiff