[PATCH] i810fb: Update i810fb documentation

Update i810fb documentation to describe new features and configuration
changes.

Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

diff --git a/Documentation/fb/intel810.txt b/Documentation/fb/intel810.txt
index fd68b162e4a13ce7cbf028405a14724224542e1f..4f0d6bc789ef0fadf101eaa362fa3d829dc8a588 100644 (file)
--- a/Documentation/fb/intel810.txt
+++ b/Documentation/fb/intel810.txt
@@ -5,6 +5,7 @@ Intel 810/815 Framebuffer driver
        March 17, 2002
 
        First Released: July 2001
+       Last Update:    September 12, 2005
 ================================================================
 
 A. Introduction
@@ -44,6 +45,8 @@ B.  Features
 
        - Hardware Cursor Support
  
+       - Supports EDID probing either by DDC/I2C or through the BIOS
+
 C.  List of available options
        
    a. "video=i810fb"  
@@ -52,14 +55,17 @@ C.  List of available options
        Recommendation: required
  
    b. "xres:<value>"  
-       select horizontal resolution in pixels
+       select horizontal resolution in pixels. (This parameter will be
+       ignored if 'mode_option' is specified.  See 'o' below).
 
        Recommendation: user preference 
        (default = 640)
 
    c. "yres:<value>"
        select vertical resolution in scanlines. If Discrete Video Timings
-       is enabled, this will be ignored and computed as 3*xres/4.  
+       is enabled, this will be ignored and computed as 3*xres/4.  (This
+       parameter will be ignored if 'mode_option' is specified.  See 'o'
+       below)  
 
        Recommendation: user preference
        (default = 480)
@@ -86,7 +92,8 @@ C.  List of available options
    g. "hsync1/hsync2:<value>" 
        select the minimum and maximum Horizontal Sync Frequency of the 
        monitor in KHz.  If a using a fixed frequency monitor, hsync1 must 
-       be equal to hsync2. 
+       be equal to hsync2. If EDID probing is successful, these will be
+       ignored and values will be taken from the EDID block.
 
        Recommendation: check monitor manual for correct values
        default (29/30)
@@ -94,7 +101,8 @@ C.  List of available options
    h. "vsync1/vsync2:<value>" 
        select the minimum and maximum Vertical Sync Frequency of the monitor
        in Hz. You can also use this option to lock your monitor's refresh 
-       rate.
+       rate. If EDID probing is successful, these will be ignored and values
+       will be taken from the EDID block.
 
        Recommendation: check monitor manual for correct values
        (default = 60/60)
@@ -154,7 +162,11 @@ C.  List of available options
 
        Recommendation: do not set
        (default = not set)
-                       
+   o. <xres>x<yres>[-<bpp>][@<refresh>]
+       The driver will now accept specification of boot mode option.  If this
+       is specified, the options 'xres' and 'yres' will be ignored. See
+       Documentation/fb/modedb.txt for usage.
+
 D. Kernel booting
 
 Separate each option/option-pair by commas (,) and the option from its value
@@ -176,7 +188,10 @@ will be computed based on the hsync1/hsync2 and vsync1/vsync2 values.
 
 IMPORTANT:
 You must include hsync1, hsync2, vsync1 and vsync2 to enable video modes
-better than 640x480 at 60Hz.
+better than 640x480 at 60Hz. HOWEVER, if your chipset/display combination
+supports I2C and has an EDID block, you can safely exclude hsync1, hsync2,
+vsync1 and vsync2 parameters.  These parameters will be taken from the EDID
+block.
 
 E.  Module options
        
@@ -217,32 +232,21 @@ F.  Setup
           This is required.  The option is under "Character Devices"
 
        d. Under "Graphics Support", select "Intel 810/815" either statically
-          or as a module.  Choose "use VESA GTF for video timings"  if you 
-          need to maximize the capability of your display.  To be on the 
+          or as a module.  Choose "use VESA Generalized Timing Formula" if
+          you need to maximize the capability of your display.  To be on the 
           safe side, you can leave this unselected.  
   
-        e. If you want a framebuffer console, enable it under "Console 
+       e. If you want support for DDC/I2C probing (Plug and Play Displays),
+          set 'Enable DDC Support' to 'y'. To make this option appear, set
+          'use VESA Generalized Timing Formula' to 'y'.
+
+        f. If you want a framebuffer console, enable it under "Console 
           Drivers"
 
-       f. Compile your kernel. 
+       g. Compile your kernel. 
                
-       g. Load the driver as described in section D and E.
+       h. Load the driver as described in section D and E.
        
-       Optional:       
-       h.  If you are going to run XFree86 with its native drivers, the 
-           standard XFree86 4.1.0 and 4.2.0 drivers should work as is.
-            However, there's a bug in the XFree86 i810 drivers.  It attempts 
-           to use XAA even when switched to the console. This will crash
-           your server. I have a fix at this site:  
-           
-           http://i810fb.sourceforge.net.  
-
-           You can either use the patch, or just replace 
-           
-            /usr/X11R6/lib/modules/drivers/i810_drv.o
-
-           with the one provided at the website.       
-
        i.  Try the DirectFB (http://www.directfb.org) + the i810 gfxdriver
            patch to see the chipset in action (or inaction :-).