Core support of the Atmel SSC library for all Atmel AT91 processors.
Based on David Brownell's initial patch for the AT91RM9200.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
#endif
+/* --------------------------------------------------------------------
+ * SSC -- Synchronous Serial Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
+static u64 ssc0_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ssc0_resources[] = {
+ [0] = {
+ .start = AT91RM9200_BASE_SSC0,
+ .end = AT91RM9200_BASE_SSC0 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91RM9200_ID_SSC0,
+ .end = AT91RM9200_ID_SSC0,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91rm9200_ssc0_device = {
+ .name = "ssc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &ssc0_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc0_resources,
+ .num_resources = ARRAY_SIZE(ssc0_resources),
+};
+
+static inline void configure_ssc0_pins(unsigned pins)
+{
+ if (pins & ATMEL_SSC_TF)
+ at91_set_A_periph(AT91_PIN_PB0, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_A_periph(AT91_PIN_PB1, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_A_periph(AT91_PIN_PB2, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_A_periph(AT91_PIN_PB3, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_A_periph(AT91_PIN_PB4, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_A_periph(AT91_PIN_PB5, 1);
+}
+
+static u64 ssc1_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ssc1_resources[] = {
+ [0] = {
+ .start = AT91RM9200_BASE_SSC1,
+ .end = AT91RM9200_BASE_SSC1 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91RM9200_ID_SSC1,
+ .end = AT91RM9200_ID_SSC1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91rm9200_ssc1_device = {
+ .name = "ssc",
+ .id = 1,
+ .dev = {
+ .dma_mask = &ssc1_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc1_resources,
+ .num_resources = ARRAY_SIZE(ssc1_resources),
+};
+
+static inline void configure_ssc1_pins(unsigned pins)
+{
+ if (pins & ATMEL_SSC_TF)
+ at91_set_A_periph(AT91_PIN_PB6, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_A_periph(AT91_PIN_PB7, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_A_periph(AT91_PIN_PB8, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_A_periph(AT91_PIN_PB9, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_A_periph(AT91_PIN_PB10, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_A_periph(AT91_PIN_PB11, 1);
+}
+
+static u64 ssc2_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ssc2_resources[] = {
+ [0] = {
+ .start = AT91RM9200_BASE_SSC2,
+ .end = AT91RM9200_BASE_SSC2 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91RM9200_ID_SSC2,
+ .end = AT91RM9200_ID_SSC2,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91rm9200_ssc2_device = {
+ .name = "ssc",
+ .id = 2,
+ .dev = {
+ .dma_mask = &ssc2_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc2_resources,
+ .num_resources = ARRAY_SIZE(ssc2_resources),
+};
+
+static inline void configure_ssc2_pins(unsigned pins)
+{
+ if (pins & ATMEL_SSC_TF)
+ at91_set_A_periph(AT91_PIN_PB12, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_A_periph(AT91_PIN_PB13, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_A_periph(AT91_PIN_PB14, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_A_periph(AT91_PIN_PB15, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_A_periph(AT91_PIN_PB16, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_A_periph(AT91_PIN_PB17, 1);
+}
+
+/*
+ * SSC controllers are accessed through library code, instead of any
+ * kind of all-singing/all-dancing driver. For example one could be
+ * used by a particular I2S audio codec's driver, while another one
+ * on the same system might be used by a custom data capture driver.
+ */
+void __init at91_add_device_ssc(unsigned id, unsigned pins)
+{
+ struct platform_device *pdev;
+
+ /*
+ * NOTE: caller is responsible for passing information matching
+ * "pins" to whatever will be using each particular controller.
+ */
+ switch (id) {
+ case AT91RM9200_ID_SSC0:
+ pdev = &at91rm9200_ssc0_device;
+ configure_ssc0_pins(pins);
+ at91_clock_associate("ssc0_clk", &pdev->dev, "ssc");
+ break;
+ case AT91RM9200_ID_SSC1:
+ pdev = &at91rm9200_ssc1_device;
+ configure_ssc1_pins(pins);
+ at91_clock_associate("ssc1_clk", &pdev->dev, "ssc");
+ break;
+ case AT91RM9200_ID_SSC2:
+ pdev = &at91rm9200_ssc2_device;
+ configure_ssc2_pins(pins);
+ at91_clock_associate("ssc2_clk", &pdev->dev, "ssc");
+ break;
+ default:
+ return;
+ }
+
+ platform_device_register(pdev);
+}
+
+#else
+void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
+#endif
+
+
/* --------------------------------------------------------------------
* UART
* -------------------------------------------------------------------- */
#endif
+/* --------------------------------------------------------------------
+ * SSC -- Synchronous Serial Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
+static u64 ssc_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ssc_resources[] = {
+ [0] = {
+ .start = AT91SAM9260_BASE_SSC,
+ .end = AT91SAM9260_BASE_SSC + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9260_ID_SSC,
+ .end = AT91SAM9260_ID_SSC,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9260_ssc_device = {
+ .name = "ssc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &ssc_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc_resources,
+ .num_resources = ARRAY_SIZE(ssc_resources),
+};
+
+static inline void configure_ssc_pins(unsigned pins)
+{
+ if (pins & ATMEL_SSC_TF)
+ at91_set_A_periph(AT91_PIN_PB17, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_A_periph(AT91_PIN_PB16, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_A_periph(AT91_PIN_PB18, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_A_periph(AT91_PIN_PB19, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_A_periph(AT91_PIN_PB20, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_A_periph(AT91_PIN_PB21, 1);
+}
+
+/*
+ * SSC controllers are accessed through library code, instead of any
+ * kind of all-singing/all-dancing driver. For example one could be
+ * used by a particular I2S audio codec's driver, while another one
+ * on the same system might be used by a custom data capture driver.
+ */
+void __init at91_add_device_ssc(unsigned id, unsigned pins)
+{
+ struct platform_device *pdev;
+
+ /*
+ * NOTE: caller is responsible for passing information matching
+ * "pins" to whatever will be using each particular controller.
+ */
+ switch (id) {
+ case AT91SAM9260_ID_SSC:
+ pdev = &at91sam9260_ssc_device;
+ configure_ssc_pins(pins);
+ at91_clock_associate("ssc_clk", &pdev->dev, "pclk");
+ break;
+ default:
+ return;
+ }
+
+ platform_device_register(pdev);
+}
+
+#else
+void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
+#endif
+
+
/* --------------------------------------------------------------------
* UART
* -------------------------------------------------------------------- */
#endif
+/* --------------------------------------------------------------------
+ * SSC -- Synchronous Serial Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
+static u64 ssc0_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ssc0_resources[] = {
+ [0] = {
+ .start = AT91SAM9261_BASE_SSC0,
+ .end = AT91SAM9261_BASE_SSC0 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9261_ID_SSC0,
+ .end = AT91SAM9261_ID_SSC0,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9261_ssc0_device = {
+ .name = "ssc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &ssc0_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc0_resources,
+ .num_resources = ARRAY_SIZE(ssc0_resources),
+};
+
+static inline void configure_ssc0_pins(unsigned pins)
+{
+ if (pins & ATMEL_SSC_TF)
+ at91_set_A_periph(AT91_PIN_PB21, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_A_periph(AT91_PIN_PB22, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_A_periph(AT91_PIN_PB23, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_A_periph(AT91_PIN_PB24, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_A_periph(AT91_PIN_PB25, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_A_periph(AT91_PIN_PB26, 1);
+}
+
+static u64 ssc1_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ssc1_resources[] = {
+ [0] = {
+ .start = AT91SAM9261_BASE_SSC1,
+ .end = AT91SAM9261_BASE_SSC1 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9261_ID_SSC1,
+ .end = AT91SAM9261_ID_SSC1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9261_ssc1_device = {
+ .name = "ssc",
+ .id = 1,
+ .dev = {
+ .dma_mask = &ssc1_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc1_resources,
+ .num_resources = ARRAY_SIZE(ssc1_resources),
+};
+
+static inline void configure_ssc1_pins(unsigned pins)
+{
+ if (pins & ATMEL_SSC_TF)
+ at91_set_B_periph(AT91_PIN_PA17, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_B_periph(AT91_PIN_PA18, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_B_periph(AT91_PIN_PA19, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_B_periph(AT91_PIN_PA20, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_B_periph(AT91_PIN_PA21, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_B_periph(AT91_PIN_PA22, 1);
+}
+
+static u64 ssc2_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ssc2_resources[] = {
+ [0] = {
+ .start = AT91SAM9261_BASE_SSC2,
+ .end = AT91SAM9261_BASE_SSC2 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9261_ID_SSC2,
+ .end = AT91SAM9261_ID_SSC2,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9261_ssc2_device = {
+ .name = "ssc",
+ .id = 2,
+ .dev = {
+ .dma_mask = &ssc2_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc2_resources,
+ .num_resources = ARRAY_SIZE(ssc2_resources),
+};
+
+static inline void configure_ssc2_pins(unsigned pins)
+{
+ if (pins & ATMEL_SSC_TF)
+ at91_set_B_periph(AT91_PIN_PC25, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_B_periph(AT91_PIN_PC26, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_B_periph(AT91_PIN_PC27, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_B_periph(AT91_PIN_PC28, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_B_periph(AT91_PIN_PC29, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_B_periph(AT91_PIN_PC30, 1);
+}
+
+/*
+ * SSC controllers are accessed through library code, instead of any
+ * kind of all-singing/all-dancing driver. For example one could be
+ * used by a particular I2S audio codec's driver, while another one
+ * on the same system might be used by a custom data capture driver.
+ */
+void __init at91_add_device_ssc(unsigned id, unsigned pins)
+{
+ struct platform_device *pdev;
+
+ /*
+ * NOTE: caller is responsible for passing information matching
+ * "pins" to whatever will be using each particular controller.
+ */
+ switch (id) {
+ case AT91SAM9261_ID_SSC0:
+ pdev = &at91sam9261_ssc0_device;
+ configure_ssc0_pins(pins);
+ at91_clock_associate("ssc0_clk", &pdev->dev, "pclk");
+ break;
+ case AT91SAM9261_ID_SSC1:
+ pdev = &at91sam9261_ssc1_device;
+ configure_ssc1_pins(pins);
+ at91_clock_associate("ssc1_clk", &pdev->dev, "pclk");
+ break;
+ case AT91SAM9261_ID_SSC2:
+ pdev = &at91sam9261_ssc2_device;
+ configure_ssc2_pins(pins);
+ at91_clock_associate("ssc2_clk", &pdev->dev, "pclk");
+ break;
+ default:
+ return;
+ }
+
+ platform_device_register(pdev);
+}
+
+#else
+void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
+#endif
+
+
/* --------------------------------------------------------------------
* UART
* -------------------------------------------------------------------- */
#endif
+/* --------------------------------------------------------------------
+ * SSC -- Synchronous Serial Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
+static u64 ssc0_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ssc0_resources[] = {
+ [0] = {
+ .start = AT91SAM9263_BASE_SSC0,
+ .end = AT91SAM9263_BASE_SSC0 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9263_ID_SSC0,
+ .end = AT91SAM9263_ID_SSC0,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9263_ssc0_device = {
+ .name = "ssc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &ssc0_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc0_resources,
+ .num_resources = ARRAY_SIZE(ssc0_resources),
+};
+
+static inline void configure_ssc0_pins(unsigned pins)
+{
+ if (pins & ATMEL_SSC_TF)
+ at91_set_B_periph(AT91_PIN_PB0, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_B_periph(AT91_PIN_PB1, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_B_periph(AT91_PIN_PB2, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_B_periph(AT91_PIN_PB3, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_B_periph(AT91_PIN_PB4, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_B_periph(AT91_PIN_PB5, 1);
+}
+
+static u64 ssc1_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ssc1_resources[] = {
+ [0] = {
+ .start = AT91SAM9263_BASE_SSC1,
+ .end = AT91SAM9263_BASE_SSC1 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9263_ID_SSC1,
+ .end = AT91SAM9263_ID_SSC1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9263_ssc1_device = {
+ .name = "ssc",
+ .id = 1,
+ .dev = {
+ .dma_mask = &ssc1_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc1_resources,
+ .num_resources = ARRAY_SIZE(ssc1_resources),
+};
+
+static inline void configure_ssc1_pins(unsigned pins)
+{
+ if (pins & ATMEL_SSC_TF)
+ at91_set_A_periph(AT91_PIN_PB6, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_A_periph(AT91_PIN_PB7, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_A_periph(AT91_PIN_PB8, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_A_periph(AT91_PIN_PB9, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_A_periph(AT91_PIN_PB10, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_A_periph(AT91_PIN_PB11, 1);
+}
+
+/*
+ * Return the device node so that board init code can use it as the
+ * parent for the device node reflecting how it's used on this board.
+ *
+ * SSC controllers are accessed through library code, instead of any
+ * kind of all-singing/all-dancing driver. For example one could be
+ * used by a particular I2S audio codec's driver, while another one
+ * on the same system might be used by a custom data capture driver.
+ */
+void __init at91_add_device_ssc(unsigned id, unsigned pins)
+{
+ struct platform_device *pdev;
+
+ /*
+ * NOTE: caller is responsible for passing information matching
+ * "pins" to whatever will be using each particular controller.
+ */
+ switch (id) {
+ case AT91SAM9263_ID_SSC0:
+ pdev = &at91sam9263_ssc0_device;
+ configure_ssc0_pins(pins);
+ at91_clock_associate("ssc0_clk", &pdev->dev, "pclk");
+ break;
+ case AT91SAM9263_ID_SSC1:
+ pdev = &at91sam9263_ssc1_device;
+ configure_ssc1_pins(pins);
+ at91_clock_associate("ssc1_clk", &pdev->dev, "pclk");
+ break;
+ default:
+ return;
+ }
+
+ platform_device_register(pdev);
+}
+
+#else
+void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
+#endif
+
+
/* --------------------------------------------------------------------
* UART
* -------------------------------------------------------------------- */
#endif
+/* --------------------------------------------------------------------
+ * SSC -- Synchronous Serial Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
+static u64 ssc0_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ssc0_resources[] = {
+ [0] = {
+ .start = AT91SAM9RL_BASE_SSC0,
+ .end = AT91SAM9RL_BASE_SSC0 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9RL_ID_SSC0,
+ .end = AT91SAM9RL_ID_SSC0,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9rl_ssc0_device = {
+ .name = "ssc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &ssc0_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc0_resources,
+ .num_resources = ARRAY_SIZE(ssc0_resources),
+};
+
+static inline void configure_ssc0_pins(unsigned pins)
+{
+ if (pins & ATMEL_SSC_TF)
+ at91_set_A_periph(AT91_PIN_PC0, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_A_periph(AT91_PIN_PC1, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_A_periph(AT91_PIN_PA15, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_A_periph(AT91_PIN_PA16, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_B_periph(AT91_PIN_PA10, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_B_periph(AT91_PIN_PA22, 1);
+}
+
+static u64 ssc1_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ssc1_resources[] = {
+ [0] = {
+ .start = AT91SAM9RL_BASE_SSC1,
+ .end = AT91SAM9RL_BASE_SSC1 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9RL_ID_SSC1,
+ .end = AT91SAM9RL_ID_SSC1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9rl_ssc1_device = {
+ .name = "ssc",
+ .id = 1,
+ .dev = {
+ .dma_mask = &ssc1_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc1_resources,
+ .num_resources = ARRAY_SIZE(ssc1_resources),
+};
+
+static inline void configure_ssc1_pins(unsigned pins)
+{
+ if (pins & ATMEL_SSC_TF)
+ at91_set_B_periph(AT91_PIN_PA29, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_B_periph(AT91_PIN_PA30, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_B_periph(AT91_PIN_PA13, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_B_periph(AT91_PIN_PA14, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_B_periph(AT91_PIN_PA9, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_B_periph(AT91_PIN_PA8, 1);
+}
+
+/*
+ * Return the device node so that board init code can use it as the
+ * parent for the device node reflecting how it's used on this board.
+ *
+ * SSC controllers are accessed through library code, instead of any
+ * kind of all-singing/all-dancing driver. For example one could be
+ * used by a particular I2S audio codec's driver, while another one
+ * on the same system might be used by a custom data capture driver.
+ */
+void __init at91_add_device_ssc(unsigned id, unsigned pins)
+{
+ struct platform_device *pdev;
+
+ /*
+ * NOTE: caller is responsible for passing information matching
+ * "pins" to whatever will be using each particular controller.
+ */
+ switch (id) {
+ case AT91SAM9RL_ID_SSC0:
+ pdev = &at91sam9rl_ssc0_device;
+ configure_ssc0_pins(pins);
+ at91_clock_associate("ssc0_clk", &pdev->dev, "pclk");
+ break;
+ case AT91SAM9RL_ID_SSC1:
+ pdev = &at91sam9rl_ssc1_device;
+ configure_ssc1_pins(pins);
+ at91_clock_associate("ssc1_clk", &pdev->dev, "pclk");
+ break;
+ default:
+ return;
+ }
+
+ platform_device_register(pdev);
+}
+
+#else
+void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
+#endif
+
+
/* --------------------------------------------------------------------
* UART
* -------------------------------------------------------------------- */
};
extern void __init at91_add_device_serial(void);
+/*
+ * SSC -- accessed through ssc_request(id). Drivers don't bind to SSC
+ * platform devices. Their SSC ID is part of their configuration data,
+ * along with information about which SSC signals they should use.
+ */
+#define ATMEL_SSC_TK 0x01
+#define ATMEL_SSC_TF 0x02
+#define ATMEL_SSC_TD 0x04
+#define ATMEL_SSC_TX (ATMEL_SSC_TK | ATMEL_SSC_TF | ATMEL_SSC_TD)
+
+#define ATMEL_SSC_RK 0x10
+#define ATMEL_SSC_RF 0x20
+#define ATMEL_SSC_RD 0x40
+#define ATMEL_SSC_RX (ATMEL_SSC_RK | ATMEL_SSC_RF | ATMEL_SSC_RD)
+
+extern void __init at91_add_device_ssc(unsigned id, unsigned pins);
+
/* LCD Controller */
struct atmel_lcdfb_info;
extern void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data);
projects / linux-2.6-omap-h63xx.git / commitdiff