#include <linux/major.h>
#include <linux/fs.h>
#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/fb.h>
#include <linux/mmc/host.h>
+#include <linux/mfd/tc6393xb.h>
#include <linux/pm.h>
#include <linux/delay.h>
#include <linux/gpio_keys.h>
},
};
+/*
+ * Toshiba Mobile IO Controller
+ */
+static struct resource tc6393xb_resources[] = {
+ [0] = {
+ .start = TOSA_LCDC_PHYS,
+ .end = TOSA_LCDC_PHYS + 0x3ffffff,
+ .flags = IORESOURCE_MEM,
+ },
+
+ [1] = {
+ .start = TOSA_IRQ_GPIO_TC6393XB_INT,
+ .end = TOSA_IRQ_GPIO_TC6393XB_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+
+static int tosa_tc6393xb_enable(struct platform_device *dev)
+{
+ int rc;
+
+ rc = gpio_request(TOSA_GPIO_TC6393XB_REST_IN, "tc6393xb #pclr");
+ if (rc)
+ goto err_req_pclr;
+ rc = gpio_request(TOSA_GPIO_TC6393XB_SUSPEND, "tc6393xb #suspend");
+ if (rc)
+ goto err_req_suspend;
+ rc = gpio_request(TOSA_GPIO_TC6393XB_L3V_ON, "l3v");
+ if (rc)
+ goto err_req_l3v;
+ rc = gpio_direction_output(TOSA_GPIO_TC6393XB_L3V_ON, 0);
+ if (rc)
+ goto err_dir_l3v;
+ rc = gpio_direction_output(TOSA_GPIO_TC6393XB_SUSPEND, 0);
+ if (rc)
+ goto err_dir_suspend;
+ rc = gpio_direction_output(TOSA_GPIO_TC6393XB_REST_IN, 0);
+ if (rc)
+ goto err_dir_pclr;
+
+ mdelay(1);
+
+ gpio_set_value(TOSA_GPIO_TC6393XB_SUSPEND, 1);
+
+ mdelay(10);
+
+ gpio_set_value(TOSA_GPIO_TC6393XB_REST_IN, 1);
+ gpio_set_value(TOSA_GPIO_TC6393XB_L3V_ON, 1);
+
+ return 0;
+err_dir_pclr:
+err_dir_suspend:
+err_dir_l3v:
+ gpio_free(TOSA_GPIO_TC6393XB_L3V_ON);
+err_req_l3v:
+ gpio_free(TOSA_GPIO_TC6393XB_SUSPEND);
+err_req_suspend:
+ gpio_free(TOSA_GPIO_TC6393XB_REST_IN);
+err_req_pclr:
+ return rc;
+}
+
+static int tosa_tc6393xb_disable(struct platform_device *dev)
+{
+ gpio_free(TOSA_GPIO_TC6393XB_L3V_ON);
+ gpio_free(TOSA_GPIO_TC6393XB_SUSPEND);
+ gpio_free(TOSA_GPIO_TC6393XB_REST_IN);
+
+ return 0;
+}
+
+static int tosa_tc6393xb_resume(struct platform_device *dev)
+{
+ gpio_set_value(TOSA_GPIO_TC6393XB_SUSPEND, 1);
+ mdelay(10);
+ gpio_set_value(TOSA_GPIO_TC6393XB_L3V_ON, 1);
+ mdelay(10);
+
+ return 0;
+}
+
+static int tosa_tc6393xb_suspend(struct platform_device *dev)
+{
+ gpio_set_value(TOSA_GPIO_TC6393XB_L3V_ON, 0);
+ gpio_set_value(TOSA_GPIO_TC6393XB_SUSPEND, 0);
+ return 0;
+}
+
+static struct tc6393xb_platform_data tosa_tc6393xb_setup = {
+ .scr_pll2cr = 0x0cc1,
+ .scr_gper = 0x3300,
+ .scr_gpo_dsr =
+ TOSA_TC6393XB_GPIO_BIT(TOSA_GPIO_CARD_VCC_ON),
+ .scr_gpo_doecr =
+ TOSA_TC6393XB_GPIO_BIT(TOSA_GPIO_CARD_VCC_ON),
+
+ .irq_base = IRQ_BOARD_START,
+ .gpio_base = TOSA_TC6393XB_GPIO_BASE,
+
+ .enable = tosa_tc6393xb_enable,
+ .disable = tosa_tc6393xb_disable,
+ .suspend = tosa_tc6393xb_suspend,
+ .resume = tosa_tc6393xb_resume,
+};
+
+
+static struct platform_device tc6393xb_device = {
+ .name = "tc6393xb",
+ .id = -1,
+ .dev = {
+ .platform_data = &tosa_tc6393xb_setup,
+ },
+ .num_resources = ARRAY_SIZE(tc6393xb_resources),
+ .resource = tc6393xb_resources,
+};
+
static struct platform_device *devices[] __initdata = {
&tosascoop_device,
&tosascoop_jc_device,
+ &tc6393xb_device,
&tosakbd_device,
&tosa_gpio_keys_device,
&tosaled_device,
static void __init tosa_init(void)
{
+ int dummy;
+
pxa2xx_mfp_config(ARRAY_AND_SIZE(tosa_pin_config));
pxa2xx_mfp_config(ARRAY_AND_SIZE(tosa_pin_irda_off));
gpio_set_wake(MFP_PIN_GPIO1, 1);
/* enable batt_fault */
PMCR = 0x01;
+ dummy = gpiochip_reserve(TOSA_SCOOP_GPIO_BASE, 12);
+ dummy = gpiochip_reserve(TOSA_SCOOP_JC_GPIO_BASE, 12);
+ dummy = gpiochip_reserve(TOSA_TC6393XB_GPIO_BASE, 16);
+
pxa_set_mci_info(&tosa_mci_platform_data);
pxa_set_udc_info(&udc_info);
pxa_set_ficp_info(&tosa_ficp_platform_data);
#define NR_IRQS (IRQ_LOCOMO_SPI_TEND + 1)
#elif defined(CONFIG_ARCH_LUBBOCK) || \
defined(CONFIG_MACH_LOGICPD_PXA270) || \
+ defined(CONFIG_MACH_TOSA) || \
defined(CONFIG_MACH_MAINSTONE) || \
defined(CONFIG_MACH_PCM027) || \
defined(CONFIG_MACH_MAGICIAN)
*/
#define TOSA_SCOOP_GPIO_BASE NR_BUILTIN_GPIO
#define TOSA_SCOOP_PXA_VCORE1 SCOOP_GPCR_PA11
-#define TOSA_SCOOP_TC6393_REST_IN SCOOP_GPCR_PA12
+#define TOSA_GPIO_TC6393XB_REST_IN (TOSA_SCOOP_GPIO_BASE + 1)
#define TOSA_GPIO_IR_POWERDWN (TOSA_SCOOP_GPIO_BASE + 2)
#define TOSA_GPIO_SD_WP (TOSA_SCOOP_GPIO_BASE + 3)
#define TOSA_GPIO_PWR_ON (TOSA_SCOOP_GPIO_BASE + 4)
#define TOSA_SCOOP_AC_IN_OL SCOOP_GPCR_PA19
/* GPIO Direction 1 : output mode / 0:input mode */
-#define TOSA_SCOOP_IO_DIR ( TOSA_SCOOP_PXA_VCORE1 | TOSA_SCOOP_TC6393_REST_IN | \
+#define TOSA_SCOOP_IO_DIR (TOSA_SCOOP_PXA_VCORE1 | \
TOSA_SCOOP_AUD_PWR_ON |\
- TOSA_SCOOP_BT_RESET | TOSA_SCOOP_BT_PWR_EN )
-/* GPIO out put level when init 1: Hi */
-#define TOSA_SCOOP_IO_OUT ( TOSA_SCOOP_TC6393_REST_IN )
+ TOSA_SCOOP_BT_RESET | TOSA_SCOOP_BT_PWR_EN)
/*
* SCOOP2 jacket GPIOs
#define TOSA_GPIO_NOTE_LED (TOSA_SCOOP_JC_GPIO_BASE + 1)
#define TOSA_GPIO_CHRG_ERR_LED (TOSA_SCOOP_JC_GPIO_BASE + 2)
#define TOSA_GPIO_USB_PULLUP (TOSA_SCOOP_JC_GPIO_BASE + 3)
-#define TOSA_SCOOP_JC_TC6393_SUSPEND SCOOP_GPCR_PA15
-#define TOSA_SCOOP_JC_TC3693_L3V_ON SCOOP_GPCR_PA16
+#define TOSA_GPIO_TC6393XB_SUSPEND (TOSA_SCOOP_JC_GPIO_BASE + 4)
+#define TOSA_GPIO_TC6393XB_L3V_ON (TOSA_SCOOP_JC_GPIO_BASE + 5)
#define TOSA_SCOOP_JC_WLAN_DETECT SCOOP_GPCR_PA17
#define TOSA_GPIO_WLAN_LED (TOSA_SCOOP_JC_GPIO_BASE + 7)
#define TOSA_SCOOP_JC_CARD_LIMIT_SEL SCOOP_GPCR_PA19
/* GPIO Direction 1 : output mode / 0:input mode */
-#define TOSA_SCOOP_JC_IO_DIR ( \
- TOSA_SCOOP_JC_TC6393_SUSPEND | TOSA_SCOOP_JC_TC3693_L3V_ON | \
- TOSA_SCOOP_JC_CARD_LIMIT_SEL )
+#define TOSA_SCOOP_JC_IO_DIR (TOSA_SCOOP_JC_CARD_LIMIT_SEL)
+
+/*
+ * TC6393XB GPIOs
+ */
+#define TOSA_TC6393XB_GPIO_BASE (NR_BUILTIN_GPIO + 2 * 12)
+#define TOSA_TC6393XB_GPIO(i) (TOSA_TC6393XB_GPIO_BASE + (i))
+#define TOSA_TC6393XB_GPIO_BIT(gpio) (1 << (gpio - TOSA_TC6393XB_GPIO_BASE))
+
+#define TOSA_GPIO_TG_ON (TOSA_TC6393XB_GPIO_BASE + 0)
+#define TOSA_GPIO_L_MUTE (TOSA_TC6393XB_GPIO_BASE + 1)
+#define TOSA_GPIO_BL_C20MA (TOSA_TC6393XB_GPIO_BASE + 3)
+#define TOSA_GPIO_CARD_VCC_ON (TOSA_TC6393XB_GPIO_BASE + 4)
+#define TOSA_GPIO_CHARGE_OFF (TOSA_TC6393XB_GPIO_BASE + 6)
+#define TOSA_GPIO_CHARGE_OFF_JC (TOSA_TC6393XB_GPIO_BASE + 7)
+#define TOSA_GPIO_BAT0_V_ON (TOSA_TC6393XB_GPIO_BASE + 9)
+#define TOSA_GPIO_BAT1_V_ON (TOSA_TC6393XB_GPIO_BASE + 10)
+#define TOSA_GPIO_BU_CHRG_ON (TOSA_TC6393XB_GPIO_BASE + 11)
+#define TOSA_GPIO_BAT_SW_ON (TOSA_TC6393XB_GPIO_BASE + 12)
+#define TOSA_GPIO_BAT0_TH_ON (TOSA_TC6393XB_GPIO_BASE + 14)
+#define TOSA_GPIO_BAT1_TH_ON (TOSA_TC6393XB_GPIO_BASE + 15)
/*
* Timing Generator
#define TOSA_GPIO_JACKET_DETECT (7)
#define TOSA_GPIO_nSD_DETECT (9)
#define TOSA_GPIO_nSD_INT (10)
-#define TOSA_GPIO_TC6393_CLK (11)
+#define TOSA_GPIO_TC6393XB_CLK (11)
#define TOSA_GPIO_BAT1_CRG (12)
#define TOSA_GPIO_CF_CD (13)
#define TOSA_GPIO_BAT0_CRG (14)
-#define TOSA_GPIO_TC6393_INT (15)
+#define TOSA_GPIO_TC6393XB_INT (15)
#define TOSA_GPIO_BAT0_LOW (17)
-#define TOSA_GPIO_TC6393_RDY (18)
+#define TOSA_GPIO_TC6393XB_RDY (18)
#define TOSA_GPIO_ON_RESET (19)
#define TOSA_GPIO_EAR_IN (20)
#define TOSA_GPIO_CF_IRQ (21) /* CF slot0 Ready */
#define TOSA_IRQ_GPIO_BAT1_CRG IRQ_GPIO(TOSA_GPIO_BAT1_CRG)
#define TOSA_IRQ_GPIO_CF_CD IRQ_GPIO(TOSA_GPIO_CF_CD)
#define TOSA_IRQ_GPIO_BAT0_CRG IRQ_GPIO(TOSA_GPIO_BAT0_CRG)
-#define TOSA_IRQ_GPIO_TC6393_INT IRQ_GPIO(TOSA_GPIO_TC6393_INT)
+#define TOSA_IRQ_GPIO_TC6393XB_INT IRQ_GPIO(TOSA_GPIO_TC6393XB_INT)
#define TOSA_IRQ_GPIO_BAT0_LOW IRQ_GPIO(TOSA_GPIO_BAT0_LOW)
#define TOSA_IRQ_GPIO_EAR_IN IRQ_GPIO(TOSA_GPIO_EAR_IN)
#define TOSA_IRQ_GPIO_CF_IRQ IRQ_GPIO(TOSA_GPIO_CF_IRQ)
projects / linux-2.6-omap-h63xx.git / commitdiff