#include <asm/arch/usb.h>
#include <asm/arch/board.h>
-#include "common.h"
+#include "../common.h"
static int __initdata generic_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1};
static void __init omap_generic_init(void)
{
+ const struct omap_uart_config *uart_conf;
+
/*
* Make sure the serial ports are muxed on at this point.
* You have to mux them off in device drivers later on
generic_config[0].data = &generic1610_usb_config;
}
#endif
+
+ uart_conf = omap_get_config(OMAP_TAG_UART, struct omap_uart_config);
+ if (uart_conf != NULL) {
+ unsigned int enabled_ports, i;
+
+ enabled_ports = uart_conf->enabled_uarts;
+ for (i = 0; i < 3; i++) {
+ if (!(enabled_ports & (1 << i)))
+ generic_serial_ports[i] = 0;
+ }
+ }
+
omap_board_config = generic_config;
omap_board_config_size = ARRAY_SIZE(generic_config);
omap_serial_init(generic_serial_ports);
static void __init omap_generic_map_io(void)
{
- omap_map_io();
+ omap_map_common_io();
}
MACHINE_START(OMAP_GENERIC, "Generic OMAP1510/1610/1710")
#include <asm/arch/tc.h>
#include <asm/arch/usb.h>
-#include "common.h"
+#include "../common.h"
extern int omap_gpio_init(void);
};
static struct resource h2_flash_resource = {
- .start = OMAP_CS2B_PHYS,
- .end = OMAP_CS2B_PHYS + OMAP_CS2B_SIZE - 1,
+ /* This is on CS3, wherever it's mapped */
.flags = IORESOURCE_MEM,
};
omap_set_gpio_edge_ctrl(0, OMAP_GPIO_FALLING_EDGE);
}
-void h2_init_irq(void)
+static void __init h2_init_irq(void)
{
omap_init_irq();
omap_gpio_init();
static void __init h2_init(void)
{
+ /* NOTE: revC boards support NAND-boot, which can put NOR on CS2B
+ * and NAND (either 16bit or 8bit) on CS3.
+ */
+ h2_flash_resource.end = h2_flash_resource.start = omap_cs3_phys();
+ h2_flash_resource.end += SZ_32M - 1;
+
platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices));
omap_board_config = h2_config;
omap_board_config_size = ARRAY_SIZE(h2_config);
static void __init h2_map_io(void)
{
- omap_map_io();
+ omap_map_common_io();
omap_serial_init(h2_serial_ports);
}
#include <asm/arch/tc.h>
#include <asm/arch/usb.h>
-#include "common.h"
+#include "../common.h"
extern int omap_gpio_init(void);
};
static struct resource h3_flash_resource = {
- .start = OMAP_CS2B_PHYS,
- .end = OMAP_CS2B_PHYS + OMAP_CS2B_SIZE - 1,
+ /* This is on CS3, wherever it's mapped */
.flags = IORESOURCE_MEM,
};
.pins[1] = 3,
};
+static struct omap_mmc_config h3_mmc_config __initdata_or_module = {
+ .mmc_blocks = 1,
+ .mmc1_power_pin = -1, /* tps65010 GPIO4 */
+ .mmc1_switch_pin = OMAP_MPUIO(1),
+};
+
static struct omap_board_config_kernel h3_config[] = {
{ OMAP_TAG_USB, &h3_usb_config },
+ { OMAP_TAG_MMC, &h3_mmc_config },
};
static void __init h3_init(void)
{
+ h3_flash_resource.end = h3_flash_resource.start = omap_cs3_phys();
+ h3_flash_resource.end += OMAP_CS3_SIZE - 1;
(void) platform_add_devices(devices, ARRAY_SIZE(devices));
+ omap_board_config = h3_config;
+ omap_board_config_size = ARRAY_SIZE(h3_config);
}
static void __init h3_init_smc91x(void)
static void __init h3_map_io(void)
{
- omap_map_io();
+ omap_map_common_io();
omap_serial_init(h3_serial_ports);
}
#include <asm/arch/tc.h>
#include <asm/arch/usb.h>
-#include "common.h"
+#include "../common.h"
static int __initdata innovator_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1};
printk("Error requesting gpio 0 for smc91x irq\n");
return;
}
- omap_set_gpio_edge_ctrl(0, OMAP_GPIO_RISING_EDGE);
+ omap_set_gpio_edge_ctrl(0, OMAP_GPIO_FALLING_EDGE);
}
}
static void __init innovator_map_io(void)
{
- omap_map_io();
+ omap_map_common_io();
#ifdef CONFIG_ARCH_OMAP1510
if (cpu_is_omap1510()) {
static void __init netstar_map_io(void)
{
- omap_map_io();
+ omap_map_common_io();
omap_serial_init(omap_serial_ports);
}
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
+#include <asm/mach/flash.h>
#include <asm/arch/gpio.h>
#include <asm/arch/usb.h>
#include <asm/arch/mux.h>
#include <asm/arch/tc.h>
-#include "common.h"
+#include "../common.h"
-static struct map_desc osk5912_io_desc[] __initdata = {
-{ OMAP_OSK_NOR_FLASH_BASE, OMAP_OSK_NOR_FLASH_START, OMAP_OSK_NOR_FLASH_SIZE,
- MT_DEVICE },
-};
static int __initdata osk_serial_ports[OMAP_MAX_NR_PORTS] = {1, 0, 0};
+static struct mtd_partition osk_partitions[] = {
+ /* bootloader (U-Boot, etc) in first sector */
+ {
+ .name = "bootloader",
+ .offset = 0,
+ .size = SZ_128K,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ /* bootloader params in the next sector */
+ {
+ .name = "params",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_128K,
+ .mask_flags = 0,
+ }, {
+ .name = "kernel",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_2M,
+ .mask_flags = 0
+ }, {
+ .name = "filesystem",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ .mask_flags = 0
+ }
+};
+
+static struct flash_platform_data osk_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+ .parts = osk_partitions,
+ .nr_parts = ARRAY_SIZE(osk_partitions),
+};
+
+static struct resource osk_flash_resource = {
+ /* this is on CS3, wherever it's mapped */
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device osk5912_flash_device = {
+ .name = "omapflash",
+ .id = 0,
+ .dev = {
+ .platform_data = &osk_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &osk_flash_resource,
+};
+
static struct resource osk5912_smc91x_resources[] = {
[0] = {
.start = OMAP_OSK_ETHR_START, /* Physical */
};
static struct platform_device *osk5912_devices[] __initdata = {
+ &osk5912_flash_device,
&osk5912_smc91x_device,
&osk5912_cf_device,
};
omap_set_gpio_edge_ctrl(62, OMAP_GPIO_FALLING_EDGE);
}
-void osk_init_irq(void)
+static void __init osk_init_irq(void)
{
omap_init_irq();
omap_gpio_init();
static void __init osk_init(void)
{
+ osk_flash_resource.end = osk_flash_resource.start = omap_cs3_phys();
+ osk_flash_resource.end += SZ_32M - 1;
platform_add_devices(osk5912_devices, ARRAY_SIZE(osk5912_devices));
omap_board_config = osk_config;
omap_board_config_size = ARRAY_SIZE(osk_config);
static void __init osk_map_io(void)
{
- omap_map_io();
- iotable_init(osk5912_io_desc, ARRAY_SIZE(osk5912_io_desc));
+ omap_map_common_io();
omap_serial_init(osk_serial_ports);
}
#include <asm/arch/mux.h>
#include <asm/arch/fpga.h>
-#include "common.h"
+#include "../common.h"
static struct resource smc91x_resources[] = {
[0] = {
static void __init omap_perseus2_map_io(void)
{
- omap_map_io();
+ omap_map_common_io();
iotable_init(omap_perseus2_io_desc,
ARRAY_SIZE(omap_perseus2_io_desc));
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
#include <asm/mach/map.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mux.h>
#include <asm/arch/usb.h>
-#include "common.h"
+#include "../common.h"
extern void omap_init_time(void);
extern int omap_gpio_init(void);
}
arch_initcall(ext_uart_init);
+static struct flash_platform_data voiceblue_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+};
+
+static struct resource voiceblue_flash_resource = {
+ .start = OMAP_CS0_PHYS,
+ .end = OMAP_CS0_PHYS + SZ_32M - 1,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device voiceblue_flash_device = {
+ .name = "omapflash",
+ .id = 0,
+ .dev = {
+ .platform_data = &voiceblue_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &voiceblue_flash_resource,
+};
+
static struct resource voiceblue_smc91x_resources[] = {
[0] = {
.start = OMAP_CS2_PHYS + 0x300,
};
static struct platform_device *voiceblue_devices[] __initdata = {
+ &voiceblue_flash_device,
&voiceblue_smc91x_device,
};
.pins[2] = 6,
};
+static struct omap_mmc_config voiceblue_mmc_config = {
+ .mmc_blocks = 1,
+ .mmc1_power_pin = 2,
+ .mmc1_switch_pin = -1,
+};
+
+static struct omap_boot_reason_config voiceblue_boot_reason;
+
static struct omap_board_config_kernel voiceblue_config[] = {
{ OMAP_TAG_USB, &voiceblue_usb_config },
+ { OMAP_TAG_MMC, &voiceblue_mmc_config },
+ { OMAP_TAG_BOOT_REASON, &voiceblue_boot_reason },
};
static void __init voiceblue_init_irq(void)
static void __init voiceblue_init(void)
{
- /* There is a good chance board is going up, so enable Power LED
- * (it is connected through invertor) */
- omap_writeb(0x00, OMAP_LPG1_LCR);
/* Watchdog */
omap_request_gpio(0);
+ /* INIT button */
+ omap_request_gpio(1);
/* smc91x reset */
omap_request_gpio(7);
omap_set_gpio_direction(7, 0);
platform_add_devices(voiceblue_devices, ARRAY_SIZE(voiceblue_devices));
omap_board_config = voiceblue_config;
omap_board_config_size = ARRAY_SIZE(voiceblue_config);
+
+ /* There is a good chance board is going up, so enable power LED
+ * (it is connected through invertor) */
+ omap_writeb(0x00, OMAP_LPG1_LCR);
+ omap_writeb(0x00, OMAP_LPG1_PMR); /* Disable clock */
}
static int __initdata omap_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1};
static void __init voiceblue_map_io(void)
{
- omap_map_io();
+ omap_map_common_io();
omap_serial_init(omap_serial_ports);
}
if (test_and_set_bit(MACHINE_PANICED, &machine_state))
return NOTIFY_DONE;
- /* Flash Power LED
- * (TODO: Enable clock right way (enabled in bootloader already)) */
+ /* Flash power LED */
omap_writeb(0x78, OMAP_LPG1_LCR);
+ omap_writeb(0x01, OMAP_LPG1_PMR); /* Enable clock */
return NOTIFY_DONE;
}
.notifier_call = panic_event,
};
-static int __init setup_notifier(void)
+static int __init voiceblue_setup(void)
{
/* Setup panic notifier */
notifier_chain_register(&panic_notifier_list, &panic_block);
+ /* This information should come from bootloader. We do it here for
+ * now... Pushing "init" button (hangs on GPIO1) during power on
+ * resets device to factory defaults */
+ omap_set_gpio_direction(1, 1);
+ sprintf(voiceblue_boot_reason.reason_str, "poweron%s",
+ omap_get_gpio_datain(1) ? "" : "-R");
+
return 0;
}
-
-postcore_initcall(setup_notifier);
+postcore_initcall(voiceblue_setup);
static int wdt_gpio_state;
projects / linux-2.6-omap-h63xx.git / commitdiff