]> pilppa.com Git - linux-2.6-omap-h63xx.git/commitdiff
V4L/DVB (4772): Add support for DiBcom DiB7000PC
authorPatrick Boettcher <pboettcher@dibcom.fr>
Wed, 18 Oct 2006 11:34:16 +0000 (08:34 -0300)
committerMauro Carvalho Chehab <mchehab@infradead.org>
Sun, 10 Dec 2006 10:51:03 +0000 (08:51 -0200)
This patch contains support for the DiB7000PC-driver.

Signed-off-by: Francois KANOUNNIKOFF <fkanounnikoff@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/dvb/dvb-usb/Kconfig
drivers/media/dvb/dvb-usb/dib0700.h
drivers/media/dvb/dvb-usb/dib0700_core.c
drivers/media/dvb/dvb-usb/dib0700_devices.c
drivers/media/dvb/frontends/Kconfig
drivers/media/dvb/frontends/Makefile
drivers/media/dvb/frontends/dib7000p.c [new file with mode: 0644]
drivers/media/dvb/frontends/dib7000p.h [new file with mode: 0644]

index a0aeaf4bbb37ee4041c2b30d77092bf9544261f1..dfd53d5e7926c0635c0ba1f47045b90384275289 100644 (file)
@@ -69,6 +69,7 @@ config DVB_USB_DIBUSB_MC
 config DVB_USB_DIB0700
        tristate "DiBcom DiB0700 USB DVB devices (see help for supported devices)"
        depends on DVB_USB
+       select DVB_DIB7000P
        select DVB_DIB7000M
        select DVB_DIB3000MC
        select DVB_TUNER_MT2060 if !DVB_FE_CUSTOMISE
index ac84347f9d4c2b6d896cf5968dcf8ab15c8c6132..cda3adea24fb2fdf121cbc3053f7aaaf1f720a63 100644 (file)
@@ -24,18 +24,23 @@ extern int dvb_usb_dib0700_debug;
 #define REQUEST_I2C_WRITE    0x3
 #define REQUEST_POLL_RC      0x4
 #define REQUEST_JUMPRAM      0x8
+#define REQUEST_SET_CLOCK    0xB
 #define REQUEST_SET_GPIO     0xC
 #define REQUEST_ENABLE_VIDEO 0xF
        // 1 Byte: 4MSB(1 = enable streaming, 0 = disable streaming) 4LSB(Video Mode: 0 = MPEG2 188Bytes, 1 = Analog)
        // 2 Byte: MPEG2 mode:  4MSB(1 = Master Mode, 0 = Slave Mode) 4LSB(Channel 1 = bit0, Channel 2 = bit1)
        // 2 Byte: Analog mode: 4MSB(0 = 625 lines, 1 = 525 lines)    4LSB(     "                "           )
+#define REQUEST_GET_VERSION  0x15
 
 struct dib0700_state {
        u8 channel_state;
        u16 mt2060_if1[2];
+
+       u8 is_dib7000pc;
 };
 
 extern int dib0700_set_gpio(struct dvb_usb_device *, enum dib07x0_gpios gpio, u8 gpio_dir, u8 gpio_val);
+extern int dib0700_ctrl_clock(struct dvb_usb_device *d, u32 clk_MHz, u8 clock_out_gp3);
 extern int dib0700_download_firmware(struct usb_device *udev, const struct firmware *fw);
 extern int dib0700_streaming_ctrl(struct dvb_usb_adapter *adap, int onoff);
 extern struct i2c_algorithm dib0700_i2c_algo;
index dca6c6985661ec2755ba154b0a3f76fb51eec1d5..6a4d150784a6e776cfe4fbe946c0f004dc47700d 100644 (file)
@@ -135,14 +135,46 @@ struct i2c_algorithm dib0700_i2c_algo = {
 int dib0700_identify_state(struct usb_device *udev, struct dvb_usb_device_properties *props,
                        struct dvb_usb_device_description **desc, int *cold)
 {
-       u8 buf[3] = { REQUEST_SET_GPIO, 4, (GPIO_IN << 7) | (0 << 6) }; // GPIO4 is save - used for I2C
-       *cold = usb_control_msg(udev, usb_sndctrlpipe(udev,0),
-               buf[0], USB_TYPE_VENDOR | USB_DIR_OUT, 0, 0, buf, 3, USB_CTRL_GET_TIMEOUT) != 3;
+       u8 b[16];
+       s16 ret = usb_control_msg(udev, usb_rcvctrlpipe(udev,0),
+               REQUEST_GET_VERSION, USB_TYPE_VENDOR | USB_DIR_IN, 0, 0, b, 16, USB_CTRL_GET_TIMEOUT);
+
+       deb_info("FW GET_VERSION length: %d\n",ret);
+
+       *cold = ret <= 0;
 
        deb_info("cold: %d\n", *cold);
        return 0;
 }
 
+static int dib0700_set_clock(struct dvb_usb_device *d, u8 en_pll,
+       u8 pll_src, u8 pll_range, u8 clock_gpio3, u16 pll_prediv,
+       u16 pll_loopdiv, u16 free_div, u16 dsuScaler)
+{
+       u8 b[10];
+       b[0] = REQUEST_SET_CLOCK;
+       b[1] = (en_pll << 7) | (pll_src << 6) | (pll_range << 5) | (clock_gpio3 << 4);
+       b[2] = (pll_prediv >> 8)  & 0xff; // MSB
+       b[3] =  pll_prediv        & 0xff; // LSB
+       b[4] = (pll_loopdiv >> 8) & 0xff; // MSB
+       b[5] =  pll_loopdiv       & 0xff; // LSB
+       b[6] = (free_div >> 8)    & 0xff; // MSB
+       b[7] =  free_div          & 0xff; // LSB
+       b[8] = (dsuScaler >> 8)   & 0xff; // MSB
+       b[9] =  dsuScaler         & 0xff; // LSB
+
+       return dib0700_ctrl_wr(d, b, 10);
+}
+
+int dib0700_ctrl_clock(struct dvb_usb_device *d, u32 clk_MHz, u8 clock_out_gp3)
+{
+       switch (clk_MHz) {
+               case 72: dib0700_set_clock(d, 1, 0, 1, clock_out_gp3, 2, 24, 0, 0x4c); break;
+               default: return -EINVAL;
+       }
+       return 0;
+}
+
 static int dib0700_jumpram(struct usb_device *udev, u32 address)
 {
        int ret, actlen;
@@ -197,7 +229,7 @@ int dib0700_download_firmware(struct usb_device *udev, const struct firmware *fw
                /* start the firmware */
                if ((ret = dib0700_jumpram(udev, 0x70000000)) == 0) {
                        info("firmware started successfully.");
-                       msleep(100);
+                       msleep(500);
                }
        } else
                ret = -EIO;
index 305dd35a102154949cd8dad58ca621abf4778dad..c231a1e5204e16051d55e5f900930805d4be74bf 100644 (file)
@@ -10,6 +10,7 @@
 
 #include "dib3000mc.h"
 #include "dib7000m.h"
+#include "dib7000p.h"
 #include "mt2060.h"
 
 static int force_lna_activation;
@@ -96,7 +97,7 @@ static int bristol_tuner_attach(struct dvb_usb_adapter *adap)
 }
 
 /* STK7700P: Hauppauge Nova-T Stick, AVerMedia Volar */
-static struct dibx000_agc_config stk7700p_dib7000m_agc_config = {
+static struct dibx000_agc_config stk7700p_7000m_mt2060_agc_config = {
        BAND_UHF | BAND_VHF,       // band_caps
 
        /* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=5, P_agc_inv_pwm1=0, P_agc_inv_pwm2=0,
@@ -141,7 +142,52 @@ static struct dibx000_agc_config stk7700p_dib7000m_agc_config = {
        },
 };
 
-static struct dibx000_bandwidth_config stk7700p_dib7000m_mt2060_config = {
+static struct dibx000_agc_config stk7700p_7000p_mt2060_agc_config = {
+       BAND_UHF | BAND_VHF,
+
+       /* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=5, P_agc_inv_pwm1=0, P_agc_inv_pwm2=0,
+        * P_agc_inh_dc_rv_est=0, P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=2, P_agc_write=0 */
+       (0 << 15) | (0 << 14) | (5 << 11) | (0 << 10) | (0 << 9) | (0 << 8) | (3 << 5) | (0 << 4) | (2 << 1) | (0 << 0), // setup
+
+       712, // inv_gain
+       41,  // time_stabiliz
+
+       0,   // alpha_level
+       118, // thlock
+
+       0,    // wbd_inv
+       4095, // wbd_ref
+       0,    // wbd_sel
+       0,    // wbd_alpha
+
+       42598, // agc1_max
+       16384, // agc1_min
+       42598, // agc2_max
+           0, // agc2_min
+
+         0,   // agc1_pt1
+       137,   // agc1_pt2
+       255,   // agc1_pt3
+
+         0,   // agc1_slope1
+       255,   // agc1_slope2
+
+       0,     // agc2_pt1
+       0,     // agc2_pt2
+
+        0,    // agc2_slope1
+       41,    // agc2_slope2
+
+       15, // alpha_mant
+       25, // alpha_exp
+
+       28, // beta_mant
+       48, // beta_exp
+
+       0, // perform_agc_softsplit
+};
+
+static struct dibx000_bandwidth_config stk7700p_pll_config = {
        60000, 30000, // internal, sampling
        1, 8, 3, 1, 0, // pll_cfg: prediv, ratio, range, reset, bypass
        0, 0, 1, 1, 0, // misc: refdiv, bypclk_div, IO_CLK_en_core, ADClkSrc, modulo
@@ -156,8 +202,19 @@ static struct dib7000m_config stk7700p_dib7000m_config = {
        .quartz_direct = 1,
 
        .agc_config_count = 1,
-       .agc = &stk7700p_dib7000m_agc_config,
-       .bw  = &stk7700p_dib7000m_mt2060_config,
+       .agc = &stk7700p_7000m_mt2060_agc_config,
+       .bw  = &stk7700p_pll_config,
+
+       .gpio_dir = DIB7000M_GPIO_DEFAULT_DIRECTIONS,
+       .gpio_val = DIB7000M_GPIO_DEFAULT_VALUES,
+       .gpio_pwm_pos = DIB7000M_GPIO_DEFAULT_PWM_POS,
+};
+
+static struct dib7000p_config stk7700p_dib7000p_config = {
+       .output_mpeg2_in_188_bytes = 1,
+
+       .agc = &stk7700p_7000p_mt2060_agc_config,
+       .bw  = &stk7700p_pll_config,
 
        .gpio_dir = DIB7000M_GPIO_DEFAULT_DIRECTIONS,
        .gpio_val = DIB7000M_GPIO_DEFAULT_VALUES,
@@ -168,13 +225,28 @@ static int stk7700p_frontend_attach(struct dvb_usb_adapter *adap)
 {
        struct dib0700_state *st = adap->dev->priv;
        /* unless there is no real power management in DVB - we leave the device on GPIO6 */
-       dib0700_set_gpio(adap->dev, GPIO6,  GPIO_OUT, 0); msleep(10);
+
+       dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
+       dib0700_set_gpio(adap->dev, GPIO6,  GPIO_OUT, 0); msleep(50);
+
        dib0700_set_gpio(adap->dev, GPIO6,  GPIO_OUT, 1); msleep(10);
+       dib0700_set_gpio(adap->dev, GPIO9,  GPIO_OUT, 1);
+
        dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0); msleep(10);
-       dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1); msleep(10);
+       dib0700_ctrl_clock(adap->dev, 72, 1);
+       dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1); msleep(100);
+
+       dib0700_set_gpio(adap->dev,  GPIO0, GPIO_OUT, 1);
 
        st->mt2060_if1[0] = 1220;
-       return (adap->fe = dvb_attach(dib7000m_attach, &adap->dev->i2c_adap, 18, &stk7700p_dib7000m_config)) == NULL ? -ENODEV : 0;
+
+       if (dib7000pc_detection(&adap->dev->i2c_adap)) {
+               adap->fe = dvb_attach(dib7000p_attach, &adap->dev->i2c_adap, 18, &stk7700p_dib7000p_config);
+               st->is_dib7000pc = 1;
+       } else
+               adap->fe = dvb_attach(dib7000m_attach, &adap->dev->i2c_adap, 18, &stk7700p_dib7000m_config);
+
+       return adap->fe == NULL ? -ENODEV : 0;
 }
 
 static struct mt2060_config stk7700p_mt2060_config = {
@@ -184,8 +256,14 @@ static struct mt2060_config stk7700p_mt2060_config = {
 static int stk7700p_tuner_attach(struct dvb_usb_adapter *adap)
 {
        struct dib0700_state *st = adap->dev->priv;
-       struct i2c_adapter *tun_i2c = dib7000m_get_i2c_master(adap->fe, DIBX000_I2C_INTERFACE_TUNER, 1);
-       return dvb_attach(mt2060_attach,adap->fe, tun_i2c, &stk7700p_mt2060_config,
+       struct i2c_adapter *tun_i2c;
+
+       if (st->is_dib7000pc)
+               tun_i2c = dib7000p_get_i2c_master(adap->fe, DIBX000_I2C_INTERFACE_TUNER, 1);
+       else
+               tun_i2c = dib7000m_get_i2c_master(adap->fe, DIBX000_I2C_INTERFACE_TUNER, 1);
+
+       return dvb_attach(mt2060_attach, adap->fe, tun_i2c, &stk7700p_mt2060_config,
                st->mt2060_if1[0]) == NULL ? -ENODEV : 0;
 }
 
index 093c7695883db08d20d763d05376c8fe6a0d45dd..7279e587e14f05a8c8997485692c6d8dfb2912a5 100644 (file)
@@ -180,6 +180,14 @@ config DVB_DIB7000M
          A DVB-T tuner module. Designed for mobile usage. Say Y when you want
          to support this frontend.
 
+config DVB_DIB7000P
+       tristate "DiBcom 7000PC"
+       depends on DVB_CORE && I2C
+       default m if DVB_FE_CUSTOMISE
+       help
+         A DVB-T tuner module. Designed for mobile usage. Say Y when you want
+         to support this frontend.
+
 comment "DVB-C (cable) frontends"
        depends on DVB_CORE
 
index 244e87417b0c8542c0abb1706bff63bf4ed0c4a7..593152ecf7ee9803c944501ef5d2c636030242a6 100644 (file)
@@ -14,6 +14,7 @@ obj-$(CONFIG_DVB_L64781) += l64781.o
 obj-$(CONFIG_DVB_DIB3000MB) += dib3000mb.o
 obj-$(CONFIG_DVB_DIB3000MC) += dib3000mc.o dibx000_common.o
 obj-$(CONFIG_DVB_DIB7000M) += dib7000m.o dibx000_common.o
+obj-$(CONFIG_DVB_DIB7000P) += dib7000p.o dibx000_common.o
 obj-$(CONFIG_DVB_MT312) += mt312.o
 obj-$(CONFIG_DVB_VES1820) += ves1820.o
 obj-$(CONFIG_DVB_VES1X93) += ves1x93.o
diff --git a/drivers/media/dvb/frontends/dib7000p.c b/drivers/media/dvb/frontends/dib7000p.c
new file mode 100644 (file)
index 0000000..0349a4b
--- /dev/null
@@ -0,0 +1,1019 @@
+/*
+ * Linux-DVB Driver for DiBcom's second generation DiB7000P (PC).
+ *
+ * Copyright (C) 2005-6 DiBcom (http://www.dibcom.fr/)
+ *
+ * This program is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation, version 2.
+ */
+#include <linux/kernel.h>
+#include <linux/i2c.h>
+
+#include "dvb_frontend.h"
+
+#include "dib7000p.h"
+
+static int debug;
+module_param(debug, int, 0644);
+MODULE_PARM_DESC(debug, "turn on debugging (default: 0)");
+
+#define dprintk(args...) do { if (debug) { printk(KERN_DEBUG "DiB7000P:"); printk(args); } } while (0)
+
+struct dib7000p_state {
+       struct dvb_frontend demod;
+    struct dib7000p_config cfg;
+
+       u8 i2c_addr;
+       struct i2c_adapter   *i2c_adap;
+
+       struct dibx000_i2c_master i2c_master;
+
+       u16 wbd_ref;
+
+       u8 current_band;
+       fe_bandwidth_t current_bandwidth;
+       struct dibx000_agc_config *current_agc;
+       u32 timf;
+
+       u16 gpio_dir;
+       u16 gpio_val;
+};
+
+enum dib7000p_power_mode {
+       DIB7000P_POWER_ALL = 0,
+       DIB7000P_POWER_INTERFACE_ONLY,
+};
+
+static u16 dib7000p_read_word(struct dib7000p_state *state, u16 reg)
+{
+       u8 wb[2] = { reg >> 8, reg & 0xff };
+       u8 rb[2];
+       struct i2c_msg msg[2] = {
+               { .addr = state->i2c_addr >> 1, .flags = 0,        .buf = wb, .len = 2 },
+               { .addr = state->i2c_addr >> 1, .flags = I2C_M_RD, .buf = rb, .len = 2 },
+       };
+
+       if (i2c_transfer(state->i2c_adap, msg, 2) != 2)
+               dprintk("i2c read error on %d\n",reg);
+
+       return (rb[0] << 8) | rb[1];
+}
+
+static int dib7000p_write_word(struct dib7000p_state *state, u16 reg, u16 val)
+{
+       u8 b[4] = {
+               (reg >> 8) & 0xff, reg & 0xff,
+               (val >> 8) & 0xff, val & 0xff,
+       };
+       struct i2c_msg msg = {
+               .addr = state->i2c_addr >> 1, .flags = 0, .buf = b, .len = 4
+       };
+       return i2c_transfer(state->i2c_adap, &msg, 1) != 1 ? -EREMOTEIO : 0;
+}
+static int dib7000p_set_output_mode(struct dib7000p_state *state, int mode)
+{
+       int    ret = 0;
+       u16 outreg, fifo_threshold, smo_mode;
+
+       outreg = 0;
+       fifo_threshold = 1792;
+       smo_mode = (dib7000p_read_word(state, 235) & 0x0010) | (1 << 1);
+
+       dprintk("-I-  Setting output mode for demod %p to %d\n",
+                       &state->demod, mode);
+
+       switch (mode) {
+               case OUTMODE_MPEG2_PAR_GATED_CLK:   // STBs with parallel gated clock
+                       outreg = (1 << 10);  /* 0x0400 */
+                       break;
+               case OUTMODE_MPEG2_PAR_CONT_CLK:    // STBs with parallel continues clock
+                       outreg = (1 << 10) | (1 << 6); /* 0x0440 */
+                       break;
+               case OUTMODE_MPEG2_SERIAL:          // STBs with serial input
+                       outreg = (1 << 10) | (2 << 6) | (0 << 1); /* 0x0480 */
+                       break;
+               case OUTMODE_DIVERSITY:
+                       if (state->cfg.hostbus_diversity)
+                               outreg = (1 << 10) | (4 << 6); /* 0x0500 */
+                       else
+                               outreg = (1 << 11);
+                       break;
+               case OUTMODE_MPEG2_FIFO:            // e.g. USB feeding
+                       smo_mode |= (3 << 1);
+                       fifo_threshold = 512;
+                       outreg = (1 << 10) | (5 << 6);
+                       break;
+               case OUTMODE_HIGH_Z:  // disable
+                       outreg = 0;
+                       break;
+               default:
+                       dprintk("Unhandled output_mode passed to be set for demod %p\n",&state->demod);
+                       break;
+       }
+
+       if (state->cfg.output_mpeg2_in_188_bytes)
+               smo_mode |= (1 << 5) ;
+
+       ret |= dib7000p_write_word(state,  235, smo_mode);
+       ret |= dib7000p_write_word(state,  236, fifo_threshold); /* synchronous fread */
+       ret |= dib7000p_write_word(state, 1286, outreg);         /* P_Div_active */
+
+       return ret;
+}
+
+static int dib7000p_set_power_mode(struct dib7000p_state *state, enum dib7000p_power_mode mode)
+{
+       /* by default everything is powered off */
+       u16 reg_774 = 0xffff, reg_775 = 0xffff, reg_776 = 0x0007, reg_899  = 0x0003,
+               reg_1280 = (0xfe00) | (dib7000p_read_word(state, 1280) & 0x01ff);
+
+       /* now, depending on the requested mode, we power on */
+       switch (mode) {
+               /* power up everything in the demod */
+               case DIB7000P_POWER_ALL:
+                       reg_774 = 0x0000; reg_775 = 0x0000; reg_776 = 0x0; reg_899 = 0x0; reg_1280 &= 0x01ff;
+                       break;
+               /* just leave power on the control-interfaces: GPIO and (I2C or SDIO) */
+               case DIB7000P_POWER_INTERFACE_ONLY: /* TODO power up either SDIO or I2C */
+                       reg_1280 &= ~((1 << 14) | (1 << 13) | (1 << 12) | (1 << 10));
+                       break;
+/* TODO following stuff is just converted from the dib7000-driver - check when is used what */
+       }
+
+       dib7000p_write_word(state,  774,  reg_774);
+       dib7000p_write_word(state,  775,  reg_775);
+       dib7000p_write_word(state,  776,  reg_776);
+       dib7000p_write_word(state,  899,  reg_899);
+       dib7000p_write_word(state, 1280, reg_1280);
+
+       return 0;
+}
+
+static void dib7000p_set_adc_state(struct dib7000p_state *state, enum dibx000_adc_states no)
+{
+       u16 reg_908 = dib7000p_read_word(state, 908),
+              reg_909 = dib7000p_read_word(state, 909);
+
+       switch (no) {
+               case DIBX000_SLOW_ADC_ON:
+                       reg_909 |= (1 << 1) | (1 << 0);
+                       dib7000p_write_word(state, 909, reg_909);
+                       reg_909 &= ~(1 << 1);
+                       break;
+
+               case DIBX000_SLOW_ADC_OFF:
+                       reg_909 |=  (1 << 1) | (1 << 0);
+                       break;
+
+               case DIBX000_ADC_ON:
+                       reg_908 &= 0x0fff;
+                       reg_909 &= 0x0003;
+                       break;
+
+               case DIBX000_ADC_OFF: // leave the VBG voltage on
+                       reg_908 |= (1 << 14) | (1 << 13) | (1 << 12);
+                       reg_909 |= (1 << 5) | (1 << 4) | (1 << 3) | (1 << 2);
+                       break;
+
+               case DIBX000_VBG_ENABLE:
+                       reg_908 &= ~(1 << 15);
+                       break;
+
+               case DIBX000_VBG_DISABLE:
+                       reg_908 |= (1 << 15);
+                       break;
+
+               default:
+                       break;
+       }
+
+//     dprintk("908: %x, 909: %x\n", reg_908, reg_909);
+
+       dib7000p_write_word(state, 908, reg_908);
+       dib7000p_write_word(state, 909, reg_909);
+}
+
+static int dib7000p_set_bandwidth(struct dvb_frontend *demod, u8 BW_Idx)
+{
+       struct dib7000p_state *state = demod->demodulator_priv;
+       u32 timf;
+
+       // store the current bandwidth for later use
+       state->current_bandwidth = BW_Idx;
+
+       if (state->timf == 0) {
+               dprintk("-D-  Using default timf\n");
+               timf = state->cfg.bw->timf;
+       } else {
+               dprintk("-D-  Using updated timf\n");
+               timf = state->timf;
+       }
+
+       timf = timf * (BW_INDEX_TO_KHZ(BW_Idx) / 100) / 80;
+
+       dprintk("timf: %d\n",timf);
+
+       dib7000p_write_word(state, 23, (timf >> 16) & 0xffff);
+       dib7000p_write_word(state, 24, (timf      ) & 0xffff);
+
+       return 0;
+}
+
+static int dib7000p_sad_calib(struct dib7000p_state *state)
+{
+/* internal */
+//     dib7000p_write_word(state, 72, (3 << 14) | (1 << 12) | (524 << 0)); // sampling clock of the SAD is writting in set_bandwidth
+       dib7000p_write_word(state, 73, (0 << 1) | (0 << 0));
+       dib7000p_write_word(state, 74, 776); // 0.625*3.3 / 4096
+
+       /* do the calibration */
+       dib7000p_write_word(state, 73, (1 << 0));
+       dib7000p_write_word(state, 73, (0 << 0));
+
+       msleep(1);
+
+       return 0;
+}
+
+static void dib7000p_reset_pll(struct dib7000p_state *state)
+{
+       struct dibx000_bandwidth_config *bw = &state->cfg.bw[0];
+
+       dib7000p_write_word(state, 903, (bw->pll_prediv << 5) | (((bw->pll_ratio >> 6) & 0x3) << 3) | (bw->pll_range << 1) | bw->pll_reset);
+       dib7000p_write_word(state, 900, ((bw->pll_ratio & 0x3f) << 9) | (bw->pll_bypass << 15) | (bw->modulo << 7) | (bw->ADClkSrc << 6) |
+               (bw->IO_CLK_en_core << 5) | (bw->bypclk_div << 2) | (bw->enable_refdiv << 1) | (0 << 0));
+
+       dib7000p_write_word(state, 18, ((bw->internal*1000) >> 16) & 0xffff);
+       dib7000p_write_word(state, 19,  (bw->internal*1000       ) & 0xffff);
+       dib7000p_write_word(state, 21,  (bw->ifreq          >> 16) & 0xffff);
+       dib7000p_write_word(state, 22,  (bw->ifreq               ) & 0xffff);
+
+       dib7000p_write_word(state, 72, bw->sad_cfg);
+}
+
+static int dib7000p_reset_gpio(struct dib7000p_state *st)
+{
+       /* reset the GPIOs */
+       dprintk("-D-  gpio dir: %x: gpio val: %x, gpio pwm pos: %x\n",st->gpio_dir, st->gpio_val,st->cfg.gpio_pwm_pos);
+
+       dib7000p_write_word(st, 1029, st->gpio_dir);
+       dib7000p_write_word(st, 1030, st->gpio_val);
+
+       /* TODO 1031 is P_gpio_od */
+
+       dib7000p_write_word(st, 1032, st->cfg.gpio_pwm_pos);
+
+       dib7000p_write_word(st, 1037, st->cfg.pwm_freq_div);
+       return 0;
+}
+
+static int dib7000p_demod_reset(struct dib7000p_state *state)
+{
+       dib7000p_set_power_mode(state, DIB7000P_POWER_ALL);
+
+       dib7000p_set_adc_state(state, DIBX000_VBG_ENABLE);
+
+       /* restart all parts */
+       dib7000p_write_word(state,  770, 0xffff);
+       dib7000p_write_word(state,  771, 0xffff);
+       dib7000p_write_word(state,  772, 0x001f);
+       dib7000p_write_word(state,  898, 0x0003);
+       /* except i2c, sdio, gpio - control interfaces */
+       dib7000p_write_word(state, 1280, 0x01fc - ((1 << 7) | (1 << 6) | (1 << 5)) );
+
+       dib7000p_write_word(state,  770, 0);
+       dib7000p_write_word(state,  771, 0);
+       dib7000p_write_word(state,  772, 0);
+       dib7000p_write_word(state,  898, 0);
+       dib7000p_write_word(state, 1280, 0);
+
+       /* default */
+       dib7000p_reset_pll(state);
+
+       if (dib7000p_reset_gpio(state) != 0)
+               dprintk("-E-  GPIO reset was not successful.\n");
+
+       if (dib7000p_set_output_mode(state, OUTMODE_HIGH_Z) != 0)
+               dprintk("-E-  OUTPUT_MODE could not be resetted.\n");
+
+       /* unforce divstr regardless whether i2c enumeration was done or not */
+       dib7000p_write_word(state, 1285, dib7000p_read_word(state, 1285) & ~(1 << 1) );
+
+       dib7000p_set_power_mode(state, DIB7000P_POWER_INTERFACE_ONLY);
+
+       return 0;
+}
+
+static void dib7000p_restart_agc(struct dib7000p_state *state)
+{
+       // P_restart_iqc & P_restart_agc
+       dib7000p_write_word(state, 770, 0x0c00);
+       dib7000p_write_word(state, 770, 0x0000);
+}
+
+static void dib7000p_update_lna(struct dib7000p_state *state)
+{
+       int i;
+       u16 dyn_gain;
+
+       // when there is no LNA to program return immediatly
+       if (state->cfg.update_lna == NULL)
+               return;
+
+       for (i = 0; i < 5; i++) {
+               // read dyn_gain here (because it is demod-dependent and not tuner)
+               dyn_gain = dib7000p_read_word(state, 394);
+
+               if (state->cfg.update_lna(&state->demod,dyn_gain)) { // LNA has changed
+                       dib7000p_restart_agc(state);
+                       msleep(5);
+               } else
+                       break;
+       }
+}
+
+static void dib7000p_pll_clk_cfg(struct dib7000p_state *state)
+{
+       u16 tmp = 0;
+       tmp = dib7000p_read_word(state, 903);
+       dib7000p_write_word(state, 903, (tmp | 0x1));   //pwr-up pll
+       tmp = dib7000p_read_word(state, 900);
+       dib7000p_write_word(state, 900, (tmp & 0x7fff) | (1 << 6));     //use High freq clock
+}
+
+static void dib7000p_update_timf_freq(struct dib7000p_state *state)
+{
+       u32 timf = (dib7000p_read_word(state, 427) << 16) | dib7000p_read_word(state, 428);
+       state->timf = timf * 80 / (BW_INDEX_TO_KHZ(state->current_bandwidth) / 100);
+       dib7000p_write_word(state, 23, (u16) (timf >> 16));
+       dib7000p_write_word(state, 24, (u16) (timf & 0xffff));
+       dprintk("-D-  Updated timf_frequency: %d (default: %d)\n",state->timf, state->cfg.bw->timf);
+}
+
+static void dib7000p_set_channel(struct dib7000p_state *state, struct dibx000_ofdm_channel *ch, u8 seq)
+{
+       u16 tmp, est[4]; // reg_26, reg_32, reg_33, reg_187, reg_188, reg_189, reg_190, reg_207, reg_208;
+
+       /* nfft, guard, qam, alpha */
+       dib7000p_write_word(state, 0, (ch->nfft << 7) | (ch->guard << 5) | (ch->nqam << 3) | (ch->vit_alpha));
+       dib7000p_write_word(state, 5, (seq << 4) | 1); /* do not force tps, search list 0 */
+
+       /* P_dintl_native, P_dintlv_inv, P_vit_hrch, P_vit_code_rate, P_vit_select_hp */
+       tmp = (ch->intlv_native << 6) | (ch->vit_hrch << 4) | (ch->vit_select_hp & 0x1);
+       if (ch->vit_hrch == 0 || ch->vit_select_hp == 1)
+               tmp |= (ch->vit_code_rate_hp << 1);
+       else
+               tmp |= (ch->vit_code_rate_lp << 1);
+       dib7000p_write_word(state, 208, tmp);
+
+       /* P_dvsy_sync_wait */
+       switch (ch->nfft) {
+               case 1: tmp = 256; break;
+               case 2: tmp = 128; break;
+               case 0:
+               default: tmp = 64; break;
+       }
+       tmp *= ((1 << (ch->guard)) * 3 / 2); // add 50% SFN margin
+       tmp <<= 4;
+
+       /* deactive the possibility of diversity reception if extended interleave */
+       /* P_dvsy_sync_mode = 0, P_dvsy_sync_enable=1, P_dvcb_comb_mode=2 */
+       if (ch->intlv_native || ch->nfft == 1)
+               tmp |= (1 << 2) | (2 << 0);
+       dib7000p_write_word(state, 207, tmp);
+
+       dib7000p_write_word(state, 26, 0x6680);   // timf(6xxx)
+       dib7000p_write_word(state, 29, 0x1273);   // isi inh1273 on1073
+       dib7000p_write_word(state, 32, 0x0003);   // pha_off_max(xxx3)
+       dib7000p_write_word(state, 33, 0x0005);   // sfreq(xxx5)
+
+       /* channel estimation fine configuration */
+       switch (ch->nqam) {
+               case 2:
+                       est[0] = 0x0148;       /* P_adp_regul_cnt 0.04 */
+                       est[1] = 0xfff0;       /* P_adp_noise_cnt -0.002 */
+                       est[2] = 0x00a4;       /* P_adp_regul_ext 0.02 */
+                       est[3] = 0xfff8;       /* P_adp_noise_ext -0.001 */
+                       break;
+               case 1:
+                       est[0] = 0x023d;       /* P_adp_regul_cnt 0.07 */
+                       est[1] = 0xffdf;       /* P_adp_noise_cnt -0.004 */
+                       est[2] = 0x00a4;       /* P_adp_regul_ext 0.02 */
+                       est[3] = 0xfff0;       /* P_adp_noise_ext -0.002 */
+                       break;
+               default:
+                       est[0] = 0x099a;       /* P_adp_regul_cnt 0.3 */
+                       est[1] = 0xffae;       /* P_adp_noise_cnt -0.01 */
+                       est[2] = 0x0333;       /* P_adp_regul_ext 0.1 */
+                       est[3] = 0xfff8;       /* P_adp_noise_ext -0.002 */
+                       break;
+       }
+       for (tmp = 0; tmp < 4; tmp++)
+               dib7000p_write_word(state, 187 + tmp, est[tmp]);
+
+       // set power-up level: interf+analog+AGC
+       dib7000p_set_power_mode(state, DIB7000P_POWER_ALL);
+       dib7000p_set_adc_state(state, DIBX000_ADC_ON);
+       dib7000p_pll_clk_cfg(state);
+       msleep(7);
+
+       // AGC initialization
+       if (state->cfg.agc_control)
+               state->cfg.agc_control(&state->demod, 1);
+
+       dib7000p_restart_agc(state);
+
+       // wait AGC rough lock time
+       msleep(5);
+
+       dib7000p_update_lna(state);
+
+       // wait AGC accurate lock time
+       msleep(7);
+       if (state->cfg.agc_control)
+               state->cfg.agc_control(&state->demod, 0);
+}
+
+static int dib7000p_autosearch_start(struct dvb_frontend *demod, struct dibx000_ofdm_channel *ch)
+{
+       struct dib7000p_state *state = demod->demodulator_priv;
+       struct dibx000_ofdm_channel auto_ch;
+       u32 value;
+
+       INIT_OFDM_CHANNEL(&auto_ch);
+       auto_ch.RF_kHz           = ch->RF_kHz;
+       auto_ch.Bw               = ch->Bw;
+       auto_ch.nqam             = 2;
+       auto_ch.guard            = 0;
+       auto_ch.nfft             = 1;
+       auto_ch.vit_alpha        = 1;
+       auto_ch.vit_select_hp    = 1;
+       auto_ch.vit_code_rate_hp = 2;
+       auto_ch.vit_code_rate_lp = 3;
+       auto_ch.vit_hrch         = 0;
+       auto_ch.intlv_native     = 1;
+
+       dib7000p_set_channel(state, &auto_ch, 7);
+
+       // always use the setting for 8MHz here lock_time for 7,6 MHz are longer
+       value = 30 * state->cfg.bw->internal;
+       dib7000p_write_word(state, 6,  (u16) ((value >> 16) & 0xffff)); // lock0 wait time
+       dib7000p_write_word(state, 7,  (u16)  (value        & 0xffff)); // lock0 wait time
+       value = 100 * state->cfg.bw->internal;
+       dib7000p_write_word(state, 8,  (u16) ((value >> 16) & 0xffff)); // lock1 wait time
+       dib7000p_write_word(state, 9,  (u16)  (value        & 0xffff)); // lock1 wait time
+       value = 500 * state->cfg.bw->internal;
+       dib7000p_write_word(state, 10, (u16) ((value >> 16) & 0xffff)); // lock2 wait time
+       dib7000p_write_word(state, 11, (u16)  (value        & 0xffff)); // lock2 wait time
+
+       value = dib7000p_read_word(state, 0);
+       dib7000p_write_word(state, 0, (1 << 9) | value);
+       dib7000p_read_word(state, 1284);
+       dib7000p_write_word(state, 0, (u16) value);
+
+       return 0;
+}
+
+static int dib7000p_autosearch_is_irq(struct dvb_frontend *demod)
+{
+       struct dib7000p_state *state = demod->demodulator_priv;
+       u16 irq_pending = dib7000p_read_word(state, 1284);
+
+       if (irq_pending & 0x1) // failed
+               return 1;
+
+       if (irq_pending & 0x2) // succeeded
+               return 2;
+
+       return 0; // still pending
+}
+
+static int dib7000p_tune(struct dvb_frontend *demod, struct dibx000_ofdm_channel *ch)
+{
+       struct dib7000p_state *state = demod->demodulator_priv;
+       u16 tmp = 0;
+
+       if (ch != NULL)
+               dib7000p_set_channel(state, ch, 0);
+       else
+               return -EINVAL;
+
+       // restart demod
+       dib7000p_write_word(state, 770, 0x4000);
+       dib7000p_write_word(state, 770, 0x0000);
+       msleep(45);
+
+       /* P_ctrl_inh_cor=0, P_ctrl_alpha_cor=4, P_ctrl_inh_isi=0, P_ctrl_alpha_isi=3, P_ctrl_inh_cor4=1, P_ctrl_alpha_cor4=3 */
+       dib7000p_write_word(state, 29, (0 << 14) | (4 << 10) | (0 << 9) | (3 << 5) | (1 << 4) | (0x3));
+
+       // never achieved a lock with that bandwidth so far - wait for osc-freq to update
+       if (state->timf == 0)
+               msleep(200);
+
+       /* offset loop parameters */
+
+       /* P_timf_alpha, P_corm_alpha=6, P_corm_thres=0x80 */
+       tmp = (6 << 8) | 0x80;
+       switch (ch->nfft) {
+               case 0: tmp |= (7 << 12); break;
+               case 1: tmp |= (9 << 12); break;
+               case 2: tmp |= (8 << 12); break;
+       }
+       dib7000p_write_word(state, 26, tmp);  /* timf_a(6xxx) */
+
+       /* P_ctrl_freeze_pha_shift=0, P_ctrl_pha_off_max */
+       tmp = (0 << 4);
+       switch (ch->nfft) {
+               case 0: tmp |= 0x6; break;
+               case 1: tmp |= 0x8; break;
+               case 2: tmp |= 0x7; break;
+       }
+       dib7000p_write_word(state, 32,  tmp);
+
+       /* P_ctrl_sfreq_inh=0, P_ctrl_sfreq_step */
+       tmp = (0 << 4);
+       switch (ch->nfft) {
+               case 0: tmp |= 0x6; break;
+               case 1: tmp |= 0x8; break;
+               case 2: tmp |= 0x7; break;
+       }
+       dib7000p_write_word(state, 33,  tmp);
+
+       tmp = dib7000p_read_word(state,509);
+       if (!((tmp >> 6) & 0x1)) {
+               /* restart the fec */
+               tmp = dib7000p_read_word(state,771);
+               dib7000p_write_word(state, 771, tmp | (1 << 1));
+               dib7000p_write_word(state, 771, tmp);
+               msleep(10);
+               tmp = dib7000p_read_word(state,509);
+       }
+
+       // we achieved a lock - it's time to update the osc freq
+       if ((tmp >> 6) & 0x1)
+               dib7000p_update_timf_freq(state);
+
+       return 0;
+}
+
+static int dib7000p_init(struct dvb_frontend *demod)
+{
+       struct dibx000_agc_config *agc;
+       struct dib7000p_state *state = demod->demodulator_priv;
+       int ret = 0;
+
+       // Demodulator default configuration
+       agc = state->cfg.agc;
+
+       dib7000p_set_power_mode(state, DIB7000P_POWER_ALL);
+       dib7000p_set_adc_state(state, DIBX000_SLOW_ADC_ON);
+
+       /* AGC */
+       ret |= dib7000p_write_word(state, 75 ,  agc->setup );
+       ret |= dib7000p_write_word(state, 76 ,  agc->inv_gain );
+       ret |= dib7000p_write_word(state, 77 ,  agc->time_stabiliz );
+       ret |= dib7000p_write_word(state, 100, (agc->alpha_level << 12) | agc->thlock);
+
+       // Demod AGC loop configuration
+       ret |= dib7000p_write_word(state, 101, (agc->alpha_mant << 5) | agc->alpha_exp);
+       ret |= dib7000p_write_word(state, 102, (agc->beta_mant << 6)  | agc->beta_exp);
+
+       /* AGC continued */
+       dprintk("-D-  WBD: ref: %d, sel: %d, active: %d, alpha: %d\n",
+               state->wbd_ref != 0 ? state->wbd_ref : agc->wbd_ref, agc->wbd_sel, !agc->perform_agc_softsplit, agc->wbd_sel);
+
+       if (state->wbd_ref != 0)
+               ret |= dib7000p_write_word(state, 105, (agc->wbd_inv << 12) | state->wbd_ref);
+       else
+               ret |= dib7000p_write_word(state, 105, (agc->wbd_inv << 12) | agc->wbd_ref);
+
+       ret |= dib7000p_write_word(state, 106, (agc->wbd_sel << 13) | (agc->wbd_alpha << 9) | (agc->perform_agc_softsplit << 8) );
+
+       ret |= dib7000p_write_word(state, 107,  agc->agc1_max);
+       ret |= dib7000p_write_word(state, 108,  agc->agc1_min);
+       ret |= dib7000p_write_word(state, 109,  agc->agc2_max);
+       ret |= dib7000p_write_word(state, 110,  agc->agc2_min);
+       ret |= dib7000p_write_word(state, 111, (agc->agc1_pt1 << 8) | agc->agc1_pt2 );
+       ret |= dib7000p_write_word(state, 112,  agc->agc1_pt3);
+       ret |= dib7000p_write_word(state, 113, (agc->agc1_slope1 << 8) | agc->agc1_slope2);
+       ret |= dib7000p_write_word(state, 114, (agc->agc2_pt1 << 8) | agc->agc2_pt2);
+       ret |= dib7000p_write_word(state, 115, (agc->agc2_slope1 << 8) | agc->agc2_slope2);
+
+       /* disable power smoothing */
+       ret |= dib7000p_write_word(state, 145, 0);
+       ret |= dib7000p_write_word(state, 146, 0);
+       ret |= dib7000p_write_word(state, 147, 0);
+       ret |= dib7000p_write_word(state, 148, 0);
+       ret |= dib7000p_write_word(state, 149, 0);
+       ret |= dib7000p_write_word(state, 150, 0);
+       ret |= dib7000p_write_word(state, 151, 0);
+       ret |= dib7000p_write_word(state, 152, 0);
+
+       // P_timf_alpha=6, P_corm_alpha=6, P_corm_thres=128 default: 6,4,26
+       ret |= dib7000p_write_word(state, 26 ,0x6680);
+
+       // P_palf_filter_on=1, P_palf_filter_freeze=0, P_palf_alpha_regul=16
+       ret |= dib7000p_write_word(state, 142,0x0410);
+       // P_fft_freq_dir=1, P_fft_nb_to_cut=0
+       ret |= dib7000p_write_word(state, 154,1 << 13);
+       // P_pha3_thres, default 0x3000
+       ret |= dib7000p_write_word(state, 168,0x0ccd);
+       // P_cti_use_cpe=0, P_cti_use_prog=0, P_cti_win_len=16, default: 0x0010
+       //ret |= dib7000p_write_word(state, 169,0x0010);
+       // P_cspu_regul=512, P_cspu_win_cut=15, default: 0x2005
+       ret |= dib7000p_write_word(state, 183,0x200f);
+       // P_adp_regul_cnt=573, default: 410
+       ret |= dib7000p_write_word(state, 187,0x023d);
+       // P_adp_noise_cnt=
+       ret |= dib7000p_write_word(state, 188,0x00a4);
+       // P_adp_regul_ext
+       ret |= dib7000p_write_word(state, 189,0x00a4);
+       // P_adp_noise_ext
+       ret |= dib7000p_write_word(state, 190,0x7ff0);
+       // P_adp_fil
+       ret |= dib7000p_write_word(state, 191,0x3ccc);
+
+       ret |= dib7000p_write_word(state, 222,0x0010);
+       // P_smo_mode, P_smo_rs_discard, P_smo_fifo_flush, P_smo_pid_parse, P_smo_error_discard
+       ret |= dib7000p_write_word(state, 235,0x0062);
+
+       // P_iqc_alpha_pha, P_iqc_alpha_amp_dcc_alpha, ...
+       if(state->cfg.tuner_is_baseband)
+               ret |= dib7000p_write_word(state, 36,0x0755);
+       else
+               ret |= dib7000p_write_word(state, 36,0x1f55);
+
+       // auto search configuration
+       ret |= dib7000p_write_word(state, 2  ,0x0004);
+       ret |= dib7000p_write_word(state, 3  ,0x1000);
+
+       /* Equal Lock */
+       ret |= dib7000p_write_word(state, 4   ,0x0814);
+
+       ret |= dib7000p_write_word(state, 6  ,0x001b);
+       ret |= dib7000p_write_word(state, 7  ,0x7740);
+       ret |= dib7000p_write_word(state, 8  ,0x005b);
+       ret |= dib7000p_write_word(state, 9  ,0x8d80);
+       ret |= dib7000p_write_word(state, 10 ,0x01c9);
+       ret |= dib7000p_write_word(state, 11 ,0xc380);
+       ret |= dib7000p_write_word(state, 12 ,0x0000);
+       ret |= dib7000p_write_word(state, 13 ,0x0080);
+       ret |= dib7000p_write_word(state, 14 ,0x0000);
+       ret |= dib7000p_write_word(state, 15 ,0x0090);
+       ret |= dib7000p_write_word(state, 16 ,0x0001);
+       ret |= dib7000p_write_word(state, 17 ,0xd4c0);
+
+       // P_clk_cfg1
+       ret |= dib7000p_write_word(state, 901, 0x0006);
+
+       // P_divclksel=3 P_divbitsel=1
+       ret |= dib7000p_write_word(state, 902, (3 << 10) | (1 << 6));
+
+       // Tuner IO bank: max drive (14mA) + divout pads max drive
+       ret |= dib7000p_write_word(state, 905, 0x2c8e);
+
+       ret |= dib7000p_set_bandwidth(&state->demod, BANDWIDTH_8_MHZ);
+       dib7000p_sad_calib(state);
+
+       return ret;
+}
+
+static int dib7000p_sleep(struct dvb_frontend *demod)
+{
+       struct dib7000p_state *state = demod->demodulator_priv;
+       return dib7000p_set_output_mode(state, OUTMODE_HIGH_Z) | dib7000p_set_power_mode(state, DIB7000P_POWER_INTERFACE_ONLY);
+}
+
+static int dib7000p_identify(struct dib7000p_state *st)
+{
+       u16 value;
+       dprintk("-I-  DiB7000PC: checking demod on I2C address: %d (%x)\n",
+               st->i2c_addr, st->i2c_addr);
+
+       if ((value = dib7000p_read_word(st, 768)) != 0x01b3) {
+               dprintk("-E-  DiB7000PC: wrong Vendor ID (read=0x%x)\n",value);
+               return -EREMOTEIO;
+       }
+
+       if ((value = dib7000p_read_word(st, 769)) != 0x4000) {
+               dprintk("-E-  DiB7000PC: wrong Device ID (%x)\n",value);
+               return -EREMOTEIO;
+       }
+
+       return 0;
+}
+
+
+static int dib7000p_get_frontend(struct dvb_frontend* fe,
+                               struct dvb_frontend_parameters *fep)
+{
+       struct dib7000p_state *state = fe->demodulator_priv;
+       u16 tps = dib7000p_read_word(state,463);
+
+       fep->inversion = INVERSION_AUTO;
+
+       fep->u.ofdm.bandwidth = state->current_bandwidth;
+
+       switch ((tps >> 8) & 0x3) {
+               case 0: fep->u.ofdm.transmission_mode = TRANSMISSION_MODE_2K; break;
+               case 1: fep->u.ofdm.transmission_mode = TRANSMISSION_MODE_8K; break;
+               /* case 2: fep->u.ofdm.transmission_mode = TRANSMISSION_MODE_4K; break; */
+       }
+
+       switch (tps & 0x3) {
+               case 0: fep->u.ofdm.guard_interval = GUARD_INTERVAL_1_32; break;
+               case 1: fep->u.ofdm.guard_interval = GUARD_INTERVAL_1_16; break;
+               case 2: fep->u.ofdm.guard_interval = GUARD_INTERVAL_1_8; break;
+               case 3: fep->u.ofdm.guard_interval = GUARD_INTERVAL_1_4; break;
+       }
+
+       switch ((tps >> 14) & 0x3) {
+               case 0: fep->u.ofdm.constellation = QPSK; break;
+               case 1: fep->u.ofdm.constellation = QAM_16; break;
+               case 2:
+               default: fep->u.ofdm.constellation = QAM_64; break;
+       }
+
+       /* as long as the frontend_param structure is fixed for hierarchical transmission I refuse to use it */
+       /* (tps >> 13) & 0x1 == hrch is used, (tps >> 10) & 0x7 == alpha */
+
+       fep->u.ofdm.hierarchy_information = HIERARCHY_NONE;
+       switch ((tps >> 5) & 0x7) {
+               case 1: fep->u.ofdm.code_rate_HP = FEC_1_2; break;
+               case 2: fep->u.ofdm.code_rate_HP = FEC_2_3; break;
+               case 3: fep->u.ofdm.code_rate_HP = FEC_3_4; break;
+               case 5: fep->u.ofdm.code_rate_HP = FEC_5_6; break;
+               case 7:
+               default: fep->u.ofdm.code_rate_HP = FEC_7_8; break;
+
+       }
+
+       switch ((tps >> 2) & 0x7) {
+               case 1: fep->u.ofdm.code_rate_LP = FEC_1_2; break;
+               case 2: fep->u.ofdm.code_rate_LP = FEC_2_3; break;
+               case 3: fep->u.ofdm.code_rate_LP = FEC_3_4; break;
+               case 5: fep->u.ofdm.code_rate_LP = FEC_5_6; break;
+               case 7:
+               default: fep->u.ofdm.code_rate_LP = FEC_7_8; break;
+       }
+
+       /* native interleaver: (dib7000p_read_word(state, 464) >>  5) & 0x1 */
+
+       return 0;
+}
+
+static int dib7000p_set_frontend(struct dvb_frontend* fe,
+                               struct dvb_frontend_parameters *fep)
+{
+       struct dib7000p_state *state = fe->demodulator_priv;
+       struct dibx000_ofdm_channel ch;
+
+       INIT_OFDM_CHANNEL(&ch);
+       FEP2DIB(fep,&ch);
+
+       state->current_bandwidth = fep->u.ofdm.bandwidth;
+       dib7000p_set_bandwidth(fe, fep->u.ofdm.bandwidth);
+
+       if (fe->ops.tuner_ops.set_params)
+               fe->ops.tuner_ops.set_params(fe, fep);
+
+       if (fep->u.ofdm.transmission_mode == TRANSMISSION_MODE_AUTO ||
+               fep->u.ofdm.guard_interval    == GUARD_INTERVAL_AUTO ||
+               fep->u.ofdm.constellation     == QAM_AUTO ||
+               fep->u.ofdm.code_rate_HP      == FEC_AUTO) {
+               int i = 800, found;
+
+               dib7000p_autosearch_start(fe, &ch);
+               do {
+                       msleep(1);
+                       found = dib7000p_autosearch_is_irq(fe);
+               } while (found == 0 && i--);
+
+               dprintk("autosearch returns: %d\n",found);
+               if (found == 0 || found == 1)
+                       return 0; // no channel found
+
+               dib7000p_get_frontend(fe, fep);
+               FEP2DIB(fep, &ch);
+       }
+
+       /* make this a config parameter */
+       dib7000p_set_output_mode(state, OUTMODE_MPEG2_FIFO);
+
+       return dib7000p_tune(fe, &ch);
+}
+
+static int dib7000p_read_status(struct dvb_frontend *fe, fe_status_t *stat)
+{
+       struct dib7000p_state *state = fe->demodulator_priv;
+       u16 lock = dib7000p_read_word(state, 509);
+
+       *stat = 0;
+
+       if (lock & 0x8000)
+               *stat |= FE_HAS_SIGNAL;
+       if (lock & 0x3000)
+               *stat |= FE_HAS_CARRIER;
+       if (lock & 0x0100)
+               *stat |= FE_HAS_VITERBI;
+       if (lock & 0x0010)
+               *stat |= FE_HAS_SYNC;
+       if (lock & 0x0008)
+               *stat |= FE_HAS_LOCK;
+
+       return 0;
+}
+
+static int dib7000p_read_ber(struct dvb_frontend *fe, u32 *ber)
+{
+       struct dib7000p_state *state = fe->demodulator_priv;
+       *ber = (dib7000p_read_word(state, 500) << 16) | dib7000p_read_word(state, 501);
+       return 0;
+}
+
+static int dib7000p_read_unc_blocks(struct dvb_frontend *fe, u32 *unc)
+{
+       struct dib7000p_state *state = fe->demodulator_priv;
+       *unc = dib7000p_read_word(state, 506);
+       return 0;
+}
+
+static int dib7000p_read_signal_strength(struct dvb_frontend *fe, u16 *strength)
+{
+       struct dib7000p_state *state = fe->demodulator_priv;
+       u16 val = dib7000p_read_word(state, 394);
+       *strength = 65535 - val;
+       return 0;
+}
+
+static int dib7000p_read_snr(struct dvb_frontend* fe, u16 *snr)
+{
+       *snr = 0x0000;
+       return 0;
+}
+
+static int dib7000p_fe_get_tune_settings(struct dvb_frontend* fe, struct dvb_frontend_tune_settings *tune)
+{
+       tune->min_delay_ms = 1000;
+       return 0;
+}
+
+static void dib7000p_release(struct dvb_frontend *demod)
+{
+       struct dib7000p_state *st = demod->demodulator_priv;
+       dibx000_exit_i2c_master(&st->i2c_master);
+       kfree(st);
+}
+
+int dib7000pc_detection(struct i2c_adapter *i2c_adap)
+{
+       u8 tx[2], rx[2];
+       struct i2c_msg msg[2] = {
+               { .addr = 18 >> 1, .flags = 0,        .buf = tx, .len = 2 },
+               { .addr = 18 >> 1, .flags = I2C_M_RD, .buf = rx, .len = 2 },
+       };
+
+       tx[0] = 0x03;
+       tx[1] = 0x00;
+
+       if (i2c_transfer(i2c_adap, msg, 2) == 2)
+               if (rx[0] == 0x01 && rx[1] == 0xb3) {
+                       dprintk("-D-  DiB7000PC detected\n");
+                       return 1;
+               }
+
+       msg[0].addr = msg[1].addr = 0x40;
+
+       if (i2c_transfer(i2c_adap, msg, 2) == 2)
+               if (rx[0] == 0x01 && rx[1] == 0xb3) {
+                       dprintk("-D-  DiB7000PC detected\n");
+                       return 1;
+               }
+
+       dprintk("-D-  DiB7000PC not detected\n");
+       return 0;
+}
+EXPORT_SYMBOL(dib7000pc_detection);
+
+struct i2c_adapter * dib7000p_get_i2c_master(struct dvb_frontend *demod, enum dibx000_i2c_interface intf, int gating)
+{
+       struct dib7000p_state *st = demod->demodulator_priv;
+       return dibx000_get_i2c_adapter(&st->i2c_master, intf, gating);
+}
+EXPORT_SYMBOL(dib7000p_get_i2c_master);
+
+int dib7000p_i2c_enumeration(struct i2c_adapter *i2c, int no_of_demods, u8 default_addr, struct dib7000p_config cfg[])
+{
+       struct dib7000p_state st = { .i2c_adap = i2c };
+       int k = 0;
+       u8 new_addr = 0;
+
+       for (k = no_of_demods-1; k >= 0; k--) {
+               st.cfg = cfg[k];
+
+               /* designated i2c address */
+               new_addr          = (0x40 + k) << 1;
+               st.i2c_addr = new_addr;
+               if (dib7000p_identify(&st) != 0) {
+                       st.i2c_addr = default_addr;
+                       if (dib7000p_identify(&st) != 0) {
+                               dprintk("DiB7000P #%d: not identified\n", k);
+                               return -EIO;
+                       }
+               }
+
+               /* start diversity to pull_down div_str - just for i2c-enumeration */
+               dib7000p_set_output_mode(&st, OUTMODE_DIVERSITY);
+
+               /* set new i2c address and force divstart */
+               dib7000p_write_word(&st, 1285, (new_addr << 2) | 0x2);
+
+               dprintk("IC %d initialized (to i2c_address 0x%x)\n", k, new_addr);
+       }
+
+       for (k = 0; k < no_of_demods; k++) {
+               st.cfg = cfg[k];
+               st.i2c_addr = (0x40 + k) << 1;
+
+               // unforce divstr
+               dib7000p_write_word(&st, 1285, st.i2c_addr << 2);
+
+               /* deactivate div - it was just for i2c-enumeration */
+               dib7000p_set_output_mode(&st, OUTMODE_HIGH_Z);
+       }
+
+       return 0;
+}
+EXPORT_SYMBOL(dib7000p_i2c_enumeration);
+
+static struct dvb_frontend_ops dib7000p_ops;
+struct dvb_frontend * dib7000p_attach(struct i2c_adapter *i2c_adap, u8 i2c_addr, struct dib7000p_config *cfg)
+{
+       struct dvb_frontend *demod;
+       struct dib7000p_state *st;
+       st = kzalloc(sizeof(struct dib7000p_state), GFP_KERNEL);
+       if (st == NULL)
+               return NULL;
+
+       memcpy(&st->cfg, cfg, sizeof(struct dib7000p_config));
+       st->i2c_adap = i2c_adap;
+       st->i2c_addr = i2c_addr;
+       st->gpio_val = cfg->gpio_val;
+       st->gpio_dir = cfg->gpio_dir;
+
+       demod                   = &st->demod;
+       demod->demodulator_priv = st;
+       memcpy(&st->demod.ops, &dib7000p_ops, sizeof(struct dvb_frontend_ops));
+
+       if (dib7000p_identify(st) != 0)
+               goto error;
+
+       dibx000_init_i2c_master(&st->i2c_master, DIB7000P, st->i2c_adap, st->i2c_addr);
+
+       dib7000p_demod_reset(st);
+
+       return demod;
+
+error:
+       kfree(st);
+       return NULL;
+}
+EXPORT_SYMBOL(dib7000p_attach);
+
+static struct dvb_frontend_ops dib7000p_ops = {
+       .info = {
+               .name = "DiBcom 7000PC",
+               .type = FE_OFDM,
+               .frequency_min      = 44250000,
+               .frequency_max      = 867250000,
+               .frequency_stepsize = 62500,
+               .caps = FE_CAN_INVERSION_AUTO |
+                       FE_CAN_FEC_1_2 | FE_CAN_FEC_2_3 | FE_CAN_FEC_3_4 |
+                       FE_CAN_FEC_5_6 | FE_CAN_FEC_7_8 | FE_CAN_FEC_AUTO |
+                       FE_CAN_QPSK | FE_CAN_QAM_16 | FE_CAN_QAM_64 | FE_CAN_QAM_AUTO |
+                       FE_CAN_TRANSMISSION_MODE_AUTO |
+                       FE_CAN_GUARD_INTERVAL_AUTO |
+                       FE_CAN_RECOVER |
+                       FE_CAN_HIERARCHY_AUTO,
+       },
+
+       .release              = dib7000p_release,
+
+       .init                 = dib7000p_init,
+       .sleep                = dib7000p_sleep,
+
+       .set_frontend         = dib7000p_set_frontend,
+       .get_tune_settings    = dib7000p_fe_get_tune_settings,
+       .get_frontend         = dib7000p_get_frontend,
+
+       .read_status          = dib7000p_read_status,
+       .read_ber             = dib7000p_read_ber,
+       .read_signal_strength = dib7000p_read_signal_strength,
+       .read_snr             = dib7000p_read_snr,
+       .read_ucblocks        = dib7000p_read_unc_blocks,
+};
+
+MODULE_AUTHOR("Patrick Boettcher <pboettcher@dibcom.fr>");
+MODULE_DESCRIPTION("Driver for the DiBcom 7000PC COFDM demodulator");
+MODULE_LICENSE("GPL");
diff --git a/drivers/media/dvb/frontends/dib7000p.h b/drivers/media/dvb/frontends/dib7000p.h
new file mode 100644 (file)
index 0000000..79465cf
--- /dev/null
@@ -0,0 +1,46 @@
+#ifndef DIB7000P_H
+#define DIB7000P_H
+
+#include "dibx000_common.h"
+
+struct dib7000p_config {
+       u8 output_mpeg2_in_188_bytes;
+       u8 hostbus_diversity;
+       u8 tuner_is_baseband;
+       int (*update_lna) (struct dvb_frontend *, u16 agc_global);
+
+       struct dibx000_agc_config *agc;
+       struct dibx000_bandwidth_config *bw;
+
+#define DIB7000P_GPIO_DEFAULT_DIRECTIONS 0xffff
+       u16 gpio_dir;
+#define DIB7000P_GPIO_DEFAULT_VALUES     0x0000
+       u16 gpio_val;
+#define DIB7000P_GPIO_PWM_POS0(v)        ((v & 0xf) << 12)
+#define DIB7000P_GPIO_PWM_POS1(v)        ((v & 0xf) << 8 )
+#define DIB7000P_GPIO_PWM_POS2(v)        ((v & 0xf) << 4 )
+#define DIB7000P_GPIO_PWM_POS3(v)         (v & 0xf)
+#define DIB7000P_GPIO_DEFAULT_PWM_POS    0xffff
+       u16 gpio_pwm_pos;
+
+       u16 pwm_freq_div;
+
+       u8 quartz_direct;
+
+       int (*agc_control) (struct dvb_frontend *, u8 before);
+};
+
+#define DEFAULT_DIB7000P_I2C_ADDRESS 18
+
+extern struct dvb_frontend * dib7000p_attach(struct i2c_adapter *i2c_adap, u8 i2c_addr, struct dib7000p_config *cfg);
+extern struct i2c_adapter * dib7000p_get_i2c_master(struct dvb_frontend *, enum dibx000_i2c_interface, int);
+extern int dib7000pc_detection(struct i2c_adapter *i2c_adap);
+
+/* TODO
+extern INT dib7000p_set_gpio(struct dibDemod *demod, UCHAR num, UCHAR dir, UCHAR val);
+extern INT dib7000p_enable_vbg_voltage(struct dibDemod *demod);
+extern void dib7000p_set_hostbus_diversity(struct dibDemod *demod, UCHAR onoff);
+extern USHORT dib7000p_get_current_agc_global(struct dibDemod *demod);
+*/
+
+#endif