]> pilppa.com Git - linux-2.6-omap-h63xx.git/commitdiff
V4L/DVB (6199): cx23885: Changes to allow demodulators on each transport bus
authorSteven Toth <stoth@hauppauge.com>
Sun, 9 Sep 2007 00:31:56 +0000 (21:31 -0300)
committerMauro Carvalho Chehab <mchehab@infradead.org>
Wed, 10 Oct 2007 01:14:29 +0000 (22:14 -0300)
cx23885: Changes to allow demodulators on each transport bus.

Signed-off-by: Steven Toth <stoth@hauppauge.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/cx23885/cx23885-cards.c
drivers/media/video/cx23885/cx23885-core.c
drivers/media/video/cx23885/cx23885-dvb.c
drivers/media/video/cx23885/cx23885-reg.h
drivers/media/video/cx23885/cx23885.h

index cdda11ddf145679f4a114ca13a7848722dc66dd0..b9012acabb2f2b6a5c01c9f83ee9bd619e430cb1 100644 (file)
@@ -111,7 +111,7 @@ struct cx23885_board cx23885_boards[] = {
        },
        [CX23885_BOARD_DVICO_FUSIONHDTV_5_EXP] = {
                .name           = "DViCO FusionHDTV5 Express",
-               .portc          = CX23885_MPEG_DVB,
+               .portb          = CX23885_MPEG_DVB,
        },
 };
 const unsigned int cx23885_bcount = ARRAY_SIZE(cx23885_boards);
@@ -197,8 +197,43 @@ static void hauppauge_eeprom(struct cx23885_dev *dev, u8 *eeprom_data)
                        dev->name, tv.model);
 }
 
+void cx23885_gpio_setup(struct cx23885_dev *dev)
+{
+       switch(dev->board) {
+       case CX23885_BOARD_HAUPPAUGE_HVR1250:
+               /* GPIO-0 cx24227 demodulator reset */
+               cx_set(GP0_IO, 0x00010001); /* Bring the part out of reset */
+               break;
+       case CX23885_BOARD_HAUPPAUGE_HVR1800:
+               /* GPIO-0 656_CLK */
+               /* GPIO-1 656_D0 */
+               /* GPIO-2 8295A Reset */
+               /* GPIO-3-10 cx23417 data0-7 */
+               /* GPIO-11-14 cx23417 addr0-3 */
+               /* GPIO-15-18 cx23417 READY, CS, RD, WR */
+               /* GPIO-19 IR_RX */
+               // FIXME: Analog requires the tuner is brought out of reset
+               break;
+       }
+}
+
+int cx23885_ir_init(struct cx23885_dev *dev)
+{
+       switch (dev->board) {
+       case CX23885_BOARD_HAUPPAUGE_HVR1250:
+       case CX23885_BOARD_HAUPPAUGE_HVR1800:
+               /* FIXME: Implement me */
+               break;
+       }
+
+       return 0;
+}
+
 void cx23885_card_setup(struct cx23885_dev *dev)
 {
+       struct cx23885_tsport *ts1 = &dev->ts1;
+       struct cx23885_tsport *ts2 = &dev->ts2;
+
        static u8 eeprom[256];
 
        if (dev->i2c_bus[0].i2c_rc == 0) {
@@ -215,6 +250,22 @@ void cx23885_card_setup(struct cx23885_dev *dev)
                        hauppauge_eeprom(dev, eeprom+0x80);
                break;
        }
+
+       switch (dev->board) {
+       case CX23885_BOARD_DVICO_FUSIONHDTV_5_EXP:
+               ts1->gen_ctrl_val  = 0xc; /* Serial bus + punctured clock */
+               ts1->ts_clk_en_val = 0x1; /* Enable TS_CLK */
+               ts1->src_sel_val   = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
+               break;
+       case CX23885_BOARD_HAUPPAUGE_HVR1250:
+       case CX23885_BOARD_HAUPPAUGE_HVR1800:
+       case CX23885_BOARD_HAUPPAUGE_HVR1800lp:
+       default:
+               ts2->gen_ctrl_val  = 0xc; /* Serial bus + punctured clock */
+               ts2->ts_clk_en_val = 0x1; /* Enable TS_CLK */
+               ts2->src_sel_val   = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
+       }
+
 }
 
 /* ------------------------------------------------------------------ */
index bcba192634760de39e00ecde7e0750d3e8d1728c..51879961e3ea97d0719eabce47985579acc538da 100644 (file)
@@ -604,24 +604,7 @@ void cx23885_reset(struct cx23885_dev *dev)
        cx23885_sram_channel_setup(dev, &dev->sram_channels[ SRAM_CH08 ], 128, 0);
        cx23885_sram_channel_setup(dev, &dev->sram_channels[ SRAM_CH09 ], 128, 0);
 
-       switch(dev->board) {
-       case CX23885_BOARD_HAUPPAUGE_HVR1250:
-               /* GPIO-0 cx24227 demodulator reset */
-               dprintk( 1, "%s() Configuring HVR1250 GPIO's\n", __FUNCTION__);
-               cx_set(GP0_IO, 0x00010001); /* Bring the part out of reset */
-               break;
-       case CX23885_BOARD_HAUPPAUGE_HVR1800:
-               /* GPIO-0 656_CLK */
-               /* GPIO-1 656_D0 */
-               /* GPIO-2 8295A Reset */
-               /* GPIO-3-10 cx23417 data0-7 */
-               /* GPIO-11-14 cx23417 addr0-3 */
-               /* GPIO-15-18 cx23417 READY, CS, RD, WR */
-               /* GPIO-19 IR_RX */
-               dprintk( 1, "%s() Configuring HVR1800 GPIO's\n", __FUNCTION__);
-               // FIXME: Analog requires the tuner is brought out of reset
-               break;
-       }
+       cx23885_gpio_setup(dev);
 }
 
 
@@ -656,17 +639,68 @@ static void cx23885_timeout(unsigned long data);
 int cx23885_risc_stopper(struct pci_dev *pci, struct btcx_riscmem *risc,
                         u32 reg, u32 mask, u32 value);
 
-static int cx23885_ir_init(struct cx23885_dev *dev)
+static int cx23885_init_tsport(struct cx23885_dev *dev, struct cx23885_tsport *port, int portno)
 {
-       dprintk(1, "%s()\n", __FUNCTION__);
-
-       switch (dev->board) {
-       case CX23885_BOARD_HAUPPAUGE_HVR1250:
-       case CX23885_BOARD_HAUPPAUGE_HVR1800:
-               dprintk(1, "%s() FIXME - Implement IR support\n", __FUNCTION__);
+       dprintk(1, "%s(portno=%d)\n", __FUNCTION__, portno);
+
+       /* Transport bus init dma queue  - Common settings */
+       port->dma_ctl_val        = 0x11; /* Enable RISC controller and Fifo */
+       port->ts_int_msk_val     = 0x1111; /* TS port bits for RISC */
+
+       spin_lock_init(&port->slock);
+       port->dev = dev;
+       port->nr = portno;
+
+       INIT_LIST_HEAD(&port->mpegq.active);
+       INIT_LIST_HEAD(&port->mpegq.queued);
+       port->mpegq.timeout.function = cx23885_timeout;
+       port->mpegq.timeout.data = (unsigned long)port;
+       init_timer(&port->mpegq.timeout);
+
+       switch(portno) {
+       case 1:
+               port->reg_gpcnt          = VID_B_GPCNT;
+               port->reg_gpcnt_ctl      = VID_B_GPCNT_CTL;
+               port->reg_dma_ctl        = VID_B_DMA_CTL;
+               port->reg_lngth          = VID_B_LNGTH;
+               port->reg_hw_sop_ctrl    = VID_B_HW_SOP_CTL;
+               port->reg_gen_ctrl       = VID_B_GEN_CTL;
+               port->reg_bd_pkt_status  = VID_B_BD_PKT_STATUS;
+               port->reg_sop_status     = VID_B_SOP_STATUS;
+               port->reg_fifo_ovfl_stat = VID_B_FIFO_OVFL_STAT;
+               port->reg_vld_misc       = VID_B_VLD_MISC;
+               port->reg_ts_clk_en      = VID_B_TS_CLK_EN;
+               port->reg_src_sel        = VID_B_SRC_SEL;
+               port->reg_ts_int_msk     = VID_B_INT_MSK;
+               port->reg_ts_int_stat   = VID_B_INT_STAT;
+               port->sram_chno          = SRAM_CH03; /* VID_B */
+               port->pci_irqmask        = 0x02; /* VID_B bit1 */
+               break;
+       case 2:
+               port->reg_gpcnt          = VID_C_GPCNT;
+               port->reg_gpcnt_ctl      = VID_C_GPCNT_CTL;
+               port->reg_dma_ctl        = VID_C_DMA_CTL;
+               port->reg_lngth          = VID_C_LNGTH;
+               port->reg_hw_sop_ctrl    = VID_C_HW_SOP_CTL;
+               port->reg_gen_ctrl       = VID_C_GEN_CTL;
+               port->reg_bd_pkt_status  = VID_C_BD_PKT_STATUS;
+               port->reg_sop_status     = VID_C_SOP_STATUS;
+               port->reg_fifo_ovfl_stat = VID_C_FIFO_OVFL_STAT;
+               port->reg_vld_misc       = VID_C_VLD_MISC;
+               port->reg_ts_clk_en      = VID_C_TS_CLK_EN;
+               port->reg_src_sel        = 0;
+               port->reg_ts_int_msk     = VID_C_INT_MSK;
+               port->reg_ts_int_stat    = VID_C_INT_STAT;
+               port->sram_chno          = SRAM_CH06; /* VID_C */
+               port->pci_irqmask        = 0x04; /* VID_C bit2 */
                break;
+       default:
+               BUG();
        }
 
+       cx23885_risc_stopper(dev->pci, &port->mpegq.stopper,
+                    port->reg_dma_ctl, port->dma_ctl_val, 0x00);
+
        return 0;
 }
 
@@ -746,16 +780,11 @@ static int cx23885_dev_setup(struct cx23885_dev *dev)
        dev->i2c_bus[2].reg_wdata = I2C3_WDATA;
        dev->i2c_bus[2].i2c_period = (0x07 << 24); /* 1.95MHz */
 
-       /* Transport bus init dma queue */
-       spin_lock_init(&dev->ts2.slock);
-       dev->ts2.dev = dev;
-       dev->ts2.nr = 2;
+       if(cx23885_boards[dev->board].portb == CX23885_MPEG_DVB)
+               cx23885_init_tsport(dev, &dev->ts1, 1);
 
-       INIT_LIST_HEAD(&dev->ts2.mpegq.active);
-       INIT_LIST_HEAD(&dev->ts2.mpegq.queued);
-       dev->ts2.mpegq.timeout.function = cx23885_timeout;
-       dev->ts2.mpegq.timeout.data     = (unsigned long)&dev->ts2;
-       init_timer(&dev->ts2.mpegq.timeout);
+       if(cx23885_boards[dev->board].portc == CX23885_MPEG_DVB)
+               cx23885_init_tsport(dev, &dev->ts2, 2);
 
        if (get_resources(dev) < 0) {
                printk(KERN_ERR "CORE %s No more PCIe resources for "
@@ -788,71 +817,21 @@ static int cx23885_dev_setup(struct cx23885_dev *dev)
        cx23885_i2c_register(&dev->i2c_bus[1]);
        cx23885_i2c_register(&dev->i2c_bus[2]);
        cx23885_call_i2c_clients (&dev->i2c_bus[0], TUNER_SET_STANDBY, NULL);
-
        cx23885_card_setup(dev);
        cx23885_ir_init(dev);
 
-       switch (dev->board) {
-       case CX23885_BOARD_DVICO_FUSIONHDTV_5_EXP:
-               dev->ts2.reg_gpcnt          = VID_B_GPCNT;
-               dev->ts2.reg_gpcnt_ctl      = VID_B_GPCNT_CTL;
-               dev->ts2.reg_dma_ctl        = VID_B_DMA_CTL;
-               dev->ts2.reg_lngth          = VID_B_LNGTH;
-               dev->ts2.reg_hw_sop_ctrl    = VID_B_HW_SOP_CTL;
-               dev->ts2.reg_gen_ctrl       = VID_B_GEN_CTL;
-               dev->ts2.reg_bd_pkt_status  = VID_B_BD_PKT_STATUS;
-               dev->ts2.reg_sop_status     = VID_B_SOP_STATUS;
-               dev->ts2.reg_fifo_ovfl_stat = VID_B_FIFO_OVFL_STAT;
-               dev->ts2.reg_vld_misc       = VID_B_VLD_MISC;
-               dev->ts2.reg_ts_clk_en      = VID_B_TS_CLK_EN;
-               dev->ts2.reg_ts_int_msk     = VID_B_INT_MSK;
-               dev->ts2.reg_src_sel        = VID_B_SRC_SEL;
-
-               // FIXME: Make this board specific
-               dev->ts2.pci_irqmask = 0x02; /* TS Port 2 bit */
-               dev->ts2.dma_ctl_val = 0x11; /* Enable RISC controller and Fifo */
-               dev->ts2.ts_int_msk_val = 0x1111; /* TS port bits for RISC */
-               dev->ts2.gen_ctrl_val = 0xc; /* Serial bus + punctured clock */
-               dev->ts2.ts_clk_en_val = 0x1; /* Enable TS_CLK */
-               dev->ts2.src_sel_val = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
-
-               // Drive this from cards.c (portb/c) and move it outside of this switch
-               dev->ts2.sram_chno = SRAM_CH03;
-               break;
-       default:
-               dev->ts2.reg_gpcnt          = VID_C_GPCNT;
-               dev->ts2.reg_gpcnt_ctl      = VID_C_GPCNT_CTL;
-               dev->ts2.reg_dma_ctl        = VID_C_DMA_CTL;
-               dev->ts2.reg_lngth          = VID_C_LNGTH;
-               dev->ts2.reg_hw_sop_ctrl    = VID_C_HW_SOP_CTL;
-               dev->ts2.reg_gen_ctrl       = VID_C_GEN_CTL;
-               dev->ts2.reg_bd_pkt_status  = VID_C_BD_PKT_STATUS;
-               dev->ts2.reg_sop_status     = VID_C_SOP_STATUS;
-               dev->ts2.reg_fifo_ovfl_stat = VID_C_FIFO_OVFL_STAT;
-               dev->ts2.reg_vld_misc       = VID_C_VLD_MISC;
-               dev->ts2.reg_ts_clk_en      = VID_C_TS_CLK_EN;
-               dev->ts2.reg_ts_int_msk     = VID_C_INT_MSK;
-               dev->ts2.reg_src_sel        = 0;
-
-               // FIXME: Make this board specific
-               dev->ts2.pci_irqmask = 0x04; /* TS Port 2 bit */
-               dev->ts2.dma_ctl_val = 0x11; /* Enable RISC controller and Fifo */
-               dev->ts2.ts_int_msk_val = 0x1111; /* TS port bits for RISC */
-               dev->ts2.gen_ctrl_val = 0xc; /* Serial bus + punctured clock */
-               dev->ts2.ts_clk_en_val = 0x1; /* Enable TS_CLK */
-               dev->ts2.src_sel_val = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
-
-               // Drive this from cards.c (portb/c) and move it outside of this switch
-               dev->ts2.sram_chno = SRAM_CH06;
+       if(cx23885_boards[dev->board].portb == CX23885_MPEG_DVB) {
+               if (cx23885_dvb_register(&dev->ts1) < 0) {
+                       printk(KERN_ERR "%s() Failed to register dvb adapters on VID_B\n",
+                              __FUNCTION__);
+               }
        }
 
-       cx23885_risc_stopper(dev->pci, &dev->ts2.mpegq.stopper,
-                            dev->ts2.reg_dma_ctl, dev->ts2.dma_ctl_val, 0x00);
-
-       // FIXME: This should only be called if ts2 is being used, driven by cards.c
-       if (cx23885_dvb_register(&dev->ts2) < 0) {
-               printk(KERN_ERR "%s() Failed to register dvb adapters\n",
-                      __FUNCTION__);
+       if(cx23885_boards[dev->board].portc == CX23885_MPEG_DVB) {
+               if (cx23885_dvb_register(&dev->ts2) < 0) {
+                       printk(KERN_ERR "%s() Failed to register dvb adapters on VID_C\n",
+                              __FUNCTION__);
+               }
        }
 
        return 0;
@@ -870,7 +849,12 @@ void cx23885_dev_unregister(struct cx23885_dev *dev)
        if (!atomic_dec_and_test(&dev->refcount))
                return;
 
-       cx23885_dvb_unregister(&dev->ts2);
+       if(cx23885_boards[dev->board].portb == CX23885_MPEG_DVB)
+               cx23885_dvb_unregister(&dev->ts1);
+
+       if(cx23885_boards[dev->board].portc == CX23885_MPEG_DVB)
+               cx23885_dvb_unregister(&dev->ts2);
+
        cx23885_i2c_unregister(&dev->i2c_bus[2]);
        cx23885_i2c_unregister(&dev->i2c_bus[1]);
        cx23885_i2c_unregister(&dev->i2c_bus[0]);
@@ -1289,14 +1273,66 @@ static void cx23885_timeout(unsigned long data)
        do_cancel_buffers(port, "timeout", 1);
 }
 
+static int cx23885_irq_ts(struct cx23885_tsport *port, u32 status)
+{
+       struct cx23885_dev *dev = port->dev;
+       int handled = 0;
+       u32 count;
+
+       if ( (status & VID_BC_MSK_OPC_ERR) ||
+            (status & VID_BC_MSK_BAD_PKT) ||
+            (status & VID_BC_MSK_SYNC) ||
+            (status & VID_BC_MSK_OF))
+       {
+               if (status & VID_BC_MSK_OPC_ERR)
+                       dprintk(7, " (VID_BC_MSK_OPC_ERR 0x%08x)\n", VID_BC_MSK_OPC_ERR);
+               if (status & VID_BC_MSK_BAD_PKT)
+                       dprintk(7, " (VID_BC_MSK_BAD_PKT 0x%08x)\n", VID_BC_MSK_BAD_PKT);
+               if (status & VID_BC_MSK_SYNC)
+                       dprintk(7, " (VID_BC_MSK_SYNC    0x%08x)\n", VID_BC_MSK_SYNC);
+               if (status & VID_BC_MSK_OF)
+                       dprintk(7, " (VID_BC_MSK_OF      0x%08x)\n", VID_BC_MSK_OF);
+
+               printk(KERN_ERR "%s: mpeg risc op code error\n", dev->name);
+
+               cx_clear(port->reg_dma_ctl, port->dma_ctl_val);
+               cx23885_sram_channel_dump(dev, &dev->sram_channels[ port->sram_chno ]);
+
+       } else if (status & VID_BC_MSK_RISCI1) {
+
+               dprintk(7, " (RISCI1            0x%08x)\n", VID_BC_MSK_RISCI1);
+
+               spin_lock(&port->slock);
+               count = cx_read(port->reg_gpcnt);
+               cx23885_wakeup(port, &port->mpegq, count);
+               spin_unlock(&port->slock);
+
+       } else if (status & VID_BC_MSK_RISCI2) {
+
+               dprintk(7, " (RISCI2            0x%08x)\n", VID_BC_MSK_RISCI2);
+
+               spin_lock(&port->slock);
+               cx23885_restart_queue(port, &port->mpegq);
+               spin_unlock(&port->slock);
+
+       }
+       if (status) {
+               cx_write(port->reg_ts_int_stat, status);
+               handled = 1;
+       }
+
+       return handled;
+}
+
 static irqreturn_t cx23885_irq(int irq, void *dev_id)
 {
        struct cx23885_dev *dev = dev_id;
-       struct cx23885_tsport *port = &dev->ts2;
+       struct cx23885_tsport *ts1 = &dev->ts1;
+       struct cx23885_tsport *ts2 = &dev->ts2;
        u32 pci_status, pci_mask;
        u32 ts1_status, ts1_mask;
        u32 ts2_status, ts2_mask;
-       int count = 0, handled = 0;
+       int ts1_count = 0, ts2_count = 0, handled = 0;
 
        pci_status = cx_read(PCI_INT_STAT);
        pci_mask = cx_read(PCI_INT_MSK);
@@ -1308,10 +1344,11 @@ static irqreturn_t cx23885_irq(int irq, void *dev_id)
        if ( (pci_status == 0) && (ts2_status == 0) && (ts1_status == 0) )
                goto out;
 
-       count = cx_read(port->reg_gpcnt);
+       ts1_count = cx_read(ts1->reg_gpcnt);
+       ts2_count = cx_read(ts2->reg_gpcnt);
        dprintk(7, "pci_status: 0x%08x  pci_mask: 0x%08x\n", pci_status, pci_mask );
-       dprintk(7, "ts1_status: 0x%08x  ts1_mask: 0x%08x count: 0x%x\n", ts1_status, ts1_mask, count );
-       dprintk(7, "ts2_status: 0x%08x  ts2_mask: 0x%08x count: 0x%x\n", ts2_status, ts2_mask, count );
+       dprintk(7, "ts1_status: 0x%08x  ts1_mask: 0x%08x count: 0x%x\n", ts1_status, ts1_mask, ts1_count );
+       dprintk(7, "ts2_status: 0x%08x  ts2_mask: 0x%08x count: 0x%x\n", ts2_status, ts2_mask, ts2_count );
 
        if ( (pci_status & PCI_MSK_RISC_RD) ||
             (pci_status & PCI_MSK_RISC_WR) ||
@@ -1348,90 +1385,11 @@ static irqreturn_t cx23885_irq(int irq, void *dev_id)
 
        }
 
-       if ( (ts1_status & VID_B_MSK_OPC_ERR) ||
-            (ts1_status & VID_B_MSK_BAD_PKT) ||
-            (ts1_status & VID_B_MSK_SYNC) ||
-            (ts1_status & VID_B_MSK_OF))
-       {
-               if (ts1_status & VID_B_MSK_OPC_ERR)
-                       dprintk(7, " (VID_B_MSK_OPC_ERR 0x%08x)\n", VID_B_MSK_OPC_ERR);
-               if (ts1_status & VID_B_MSK_BAD_PKT)
-                       dprintk(7, " (VID_B_MSK_BAD_PKT 0x%08x)\n", VID_B_MSK_BAD_PKT);
-               if (ts1_status & VID_B_MSK_SYNC)
-                       dprintk(7, " (VID_B_MSK_SYNC    0x%08x)\n", VID_B_MSK_SYNC);
-               if (ts1_status & VID_B_MSK_OF)
-                       dprintk(7, " (VID_B_MSK_OF      0x%08x)\n", VID_B_MSK_OF);
+       if (ts1_status)
+               handled += cx23885_irq_ts(ts1, ts1_status);
 
-               printk(KERN_ERR "%s: mpeg risc op code error\n", dev->name);
-
-               cx_clear(port->reg_dma_ctl, port->dma_ctl_val);
-               cx23885_sram_channel_dump(dev, &dev->sram_channels[ port->sram_chno ]);
-
-       } else if (ts1_status & VID_B_MSK_RISCI1) {
-
-               dprintk(7, " (RISCI1            0x%08x)\n", VID_B_MSK_RISCI1);
-
-               spin_lock(&port->slock);
-               count = cx_read(port->reg_gpcnt);
-               cx23885_wakeup(port, &port->mpegq, count);
-               spin_unlock(&port->slock);
-
-       } else if (ts1_status & VID_B_MSK_RISCI2) {
-
-               dprintk(7, " (RISCI2            0x%08x)\n", VID_B_MSK_RISCI2);
-
-               spin_lock(&port->slock);
-               cx23885_restart_queue(port, &port->mpegq);
-               spin_unlock(&port->slock);
-
-       }
-       if (ts1_status) {
-               cx_write(VID_B_INT_STAT, ts1_status);
-               handled = 1;
-       }
-
-       if ( (ts2_status & VID_C_MSK_OPC_ERR) ||
-            (ts2_status & VID_C_MSK_BAD_PKT) ||
-            (ts2_status & VID_C_MSK_SYNC) ||
-            (ts2_status & VID_C_MSK_OF))
-       {
-               if (ts2_status & VID_C_MSK_OPC_ERR)
-                       dprintk(7, " (VID_C_MSK_OPC_ERR 0x%08x)\n", VID_C_MSK_OPC_ERR);
-               if (ts2_status & VID_C_MSK_BAD_PKT)
-                       dprintk(7, " (VID_C_MSK_BAD_PKT 0x%08x)\n", VID_C_MSK_BAD_PKT);
-               if (ts2_status & VID_C_MSK_SYNC)
-                       dprintk(7, " (VID_C_MSK_SYNC    0x%08x)\n", VID_C_MSK_SYNC);
-               if (ts2_status & VID_C_MSK_OF)
-                       dprintk(7, " (VID_C_MSK_OF      0x%08x)\n", VID_C_MSK_OF);
-
-               printk(KERN_ERR "%s: mpeg risc op code error\n", dev->name);
-
-               cx_clear(port->reg_dma_ctl, port->dma_ctl_val);
-               cx23885_sram_channel_dump(dev, &dev->sram_channels[ port->sram_chno ]);
-
-       } else if (ts2_status & VID_C_MSK_RISCI1) {
-
-               dprintk(7, " (RISCI1            0x%08x)\n", VID_C_MSK_RISCI1);
-
-               spin_lock(&port->slock);
-               count = cx_read(port->reg_gpcnt);
-               cx23885_wakeup(port, &port->mpegq, count);
-               spin_unlock(&port->slock);
-
-       } else if (ts2_status & VID_C_MSK_RISCI2) {
-
-               dprintk(7, " (RISCI2            0x%08x)\n", VID_C_MSK_RISCI2);
-
-               spin_lock(&port->slock);
-               cx23885_restart_queue(port, &port->mpegq);
-               spin_unlock(&port->slock);
-
-       }
-
-       if (ts2_status) {
-               cx_write(VID_C_INT_STAT, ts2_status);
-               handled = 1;
-       }
+       if (ts2_status)
+               handled += cx23885_irq_ts(ts2, ts2_status);
 
        if (handled)
                cx_write(PCI_INT_STAT, pci_status);
index 0ace919195df55c88eac282b7f3c78e30f5e75c3..e0dc1495b8cdcdfd506f57e0589805bb51f3ec74 100644 (file)
@@ -160,6 +160,7 @@ static int dvb_register(struct cx23885_tsport *port)
        }
 
        /* Put the analog decoder in standby to keep it quiet */
+       /* Assumption here: analog decoder is only on i2c bus 0 */
        cx23885_call_i2c_clients (&dev->i2c_bus[0], TUNER_SET_STANDBY, NULL);
 
        /* register everything */
@@ -180,8 +181,6 @@ int cx23885_dvb_register(struct cx23885_tsport *port)
                dev->pci_slot);
 
        err = -ENODEV;
-       if (!(cx23885_boards[dev->board].portc & CX23885_MPEG_DVB))
-               goto fail_core;
 
        /* dvb stuff */
        printk("%s: cx23885 based dvb card\n", dev->name);
@@ -192,7 +191,6 @@ int cx23885_dvb_register(struct cx23885_tsport *port)
        if (err != 0)
                printk("%s() dvb_register failed err = %d\n", __FUNCTION__, err);
 
- fail_core:
        return err;
 }
 
index 3f1afbeea77868059d37804f45c40583e46f4403..162169f9091b18c52ed38d945f901817ebc80864 100644 (file)
@@ -250,14 +250,16 @@ Channel manager Data Structure entry = 20 DWORD
 #define VID_C_MSK_OF      (1 <<  8)
 #define VID_C_MSK_RISCI2  (1 <<  4)
 #define VID_C_MSK_RISCI1   1
-#define VID_C_INT_MSK  0x00040040
 
-#define VID_C_MSK_BAD_PKT (1 << 20)
-#define VID_C_MSK_OPC_ERR (1 << 16)
-#define VID_C_MSK_SYNC    (1 << 12)
-#define VID_C_MSK_OF      (1 <<  8)
-#define VID_C_MSK_RISCI2  (1 <<  4)
-#define VID_C_MSK_RISCI1   1
+/* A superset for testing purposes */
+#define VID_BC_MSK_BAD_PKT (1 << 20)
+#define VID_BC_MSK_OPC_ERR (1 << 16)
+#define VID_BC_MSK_SYNC    (1 << 12)
+#define VID_BC_MSK_OF      (1 <<  8)
+#define VID_BC_MSK_RISCI2  (1 <<  4)
+#define VID_BC_MSK_RISCI1   1
+
+#define VID_C_INT_MSK  0x00040040
 #define VID_C_INT_STAT 0x00040044
 #define VID_C_INT_MSTAT        0x00040048
 #define VID_C_INT_SSTAT        0x0004004C
index 4933274b1e3947c2928f24a688e3e4da20e92518..45c47cd607034df4f88e035d61475389a3c1ac5c 100644 (file)
@@ -168,6 +168,7 @@ struct cx23885_tsport {
        u32                        reg_vld_misc;
        u32                        reg_ts_clk_en;
        u32                        reg_ts_int_msk;
+       u32                        reg_ts_int_stat;
        u32                        reg_src_sel;
 
        /* Default register vals */
@@ -201,7 +202,7 @@ struct cx23885_dev {
        unsigned int               board;
        char                       name[32];
 
-       struct cx23885_tsport      ts2;
+       struct cx23885_tsport      ts1, ts2;
 
        /* sram configuration */
        struct sram_channel        *sram_channels;
@@ -269,6 +270,8 @@ extern struct cx23885_subid cx23885_subids[];
 extern const unsigned int cx23885_idcount;
 
 extern void cx23885_card_list(struct cx23885_dev *dev);
+extern int  cx23885_ir_init(struct cx23885_dev *dev);
+extern void cx23885_gpio_setup(struct cx23885_dev *dev);
 extern void cx23885_card_setup(struct cx23885_dev *dev);
 extern void cx23885_card_setup_pre_i2c(struct cx23885_dev *dev);