struct usb_hcd *hcd = pci_get_drvdata(dev);
int retval = 0;
int wake, w;
+ int has_pci_pm;
/* Root hub suspend should have stopped all downstream traffic,
* and all bus master traffic. And done so for both the interface
synchronize_irq(dev->irq);
+ /* Downstream ports from this root hub should already be quiesced, so
+ * there will be no DMA activity. Now we can shut down the upstream
+ * link (except maybe for PME# resume signaling) and enter some PCI
+ * low power state, if the hardware allows.
+ */
+ pci_disable_device(dev);
+
+ pci_save_state(dev);
+
/* Don't fail on error to enable wakeup. We rely on pci code
* to reject requests the hardware can't implement, rather
* than coding the same thing.
wake = w;
dev_dbg(&dev->dev, "wakeup: %d\n", wake);
- /* Downstream ports from this root hub should already be quiesced, so
- * there will be no DMA activity. Now we can shut down the upstream
- * link (except maybe for PME# resume signaling) and enter some PCI
- * low power state, if the hardware allows.
- */
- pci_disable_device(dev);
- done:
- return retval;
-}
-EXPORT_SYMBOL_GPL(usb_hcd_pci_suspend);
-
-/**
- * usb_hcd_pci_suspend_late - suspend a PCI-based HCD after IRQs are disabled
- * @dev: USB Host Controller being suspended
- * @message: Power Management message describing this state transition
- *
- * Store this function in the HCD's struct pci_driver as .suspend_late.
- */
-int usb_hcd_pci_suspend_late(struct pci_dev *dev, pm_message_t message)
-{
- int retval = 0;
- int has_pci_pm;
-
- /* We might already be suspended (runtime PM -- not yet written) */
- if (dev->current_state != PCI_D0)
- goto done;
-
- pci_save_state(dev);
-
/* Don't change state if we don't need to */
if (message.event == PM_EVENT_FREEZE ||
message.event == PM_EVENT_PRETHAW) {
done:
return retval;
}
-EXPORT_SYMBOL_GPL(usb_hcd_pci_suspend_late);
+EXPORT_SYMBOL_GPL(usb_hcd_pci_suspend);
/**
* usb_hcd_pci_resume_early - resume a PCI-based HCD before IRQs are enabled
*/
int usb_hcd_pci_resume_early(struct pci_dev *dev)
{
- int retval = 0;
- pci_power_t state = dev->current_state;
-
-#ifdef CONFIG_PPC_PMAC
- /* Reenable ASIC clocks for USB */
- if (machine_is(powermac)) {
- struct device_node *of_node;
-
- of_node = pci_device_to_OF_node(dev);
- if (of_node)
- pmac_call_feature(PMAC_FTR_USB_ENABLE,
- of_node, 0, 1);
- }
-#endif
-
- /* NOTE: chip docs cover clean "real suspend" cases (what Linux
- * calls "standby", "suspend to RAM", and so on). There are also
- * dirty cases when swsusp fakes a suspend in "shutdown" mode.
- */
- if (state != PCI_D0) {
-#ifdef DEBUG
- int pci_pm;
- u16 pmcr;
-
- pci_pm = pci_find_capability(dev, PCI_CAP_ID_PM);
- pci_read_config_word(dev, pci_pm + PCI_PM_CTRL, &pmcr);
- pmcr &= PCI_PM_CTRL_STATE_MASK;
- if (pmcr) {
- /* Clean case: power to USB and to HC registers was
- * maintained; remote wakeup is easy.
- */
- dev_dbg(&dev->dev, "resume from PCI D%d\n", pmcr);
- } else {
- /* Clean: HC lost Vcc power, D0 uninitialized
- * + Vaux may have preserved port and transceiver
- * state ... for remote wakeup from D3cold
- * + or not; HCD must reinit + re-enumerate
- *
- * Dirty: D0 semi-initialized cases with swsusp
- * + after BIOS init
- * + after Linux init (HCD statically linked)
- */
- dev_dbg(&dev->dev, "resume from previous PCI D%d\n",
- state);
- }
-#endif
-
- retval = pci_set_power_state(dev, PCI_D0);
- } else {
- /* Same basic cases: clean (powered/not), dirty */
- dev_dbg(&dev->dev, "PCI legacy resume\n");
- }
-
- if (retval < 0)
- dev_err(&dev->dev, "can't resume: %d\n", retval);
- else
- pci_restore_state(dev);
-
- return retval;
+ pci_restore_state(dev);
+ return 0;
}
EXPORT_SYMBOL_GPL(usb_hcd_pci_resume_early);
struct usb_hcd *hcd;
int retval;
+#ifdef CONFIG_PPC_PMAC
+ /* Reenable ASIC clocks for USB */
+ if (machine_is(powermac)) {
+ struct device_node *of_node;
+
+ of_node = pci_device_to_OF_node(dev);
+ if (of_node)
+ pmac_call_feature(PMAC_FTR_USB_ENABLE,
+ of_node, 0, 1);
+ }
+#endif
+
hcd = pci_get_drvdata(dev);
if (hcd->state != HC_STATE_SUSPENDED) {
dev_dbg(hcd->self.controller,
return 0;
}
+ pci_enable_wake(dev, PCI_D0, false);
+
retval = pci_enable_device(dev);
if (retval < 0) {
dev_err(&dev->dev, "can't re-enable after resume, %d!\n",
projects / linux-2.6-omap-h63xx.git / commitdiff