]> pilppa.com Git - linux-2.6-omap-h63xx.git/commitdiff
[TG3]: Add TG3_FLG2_IS_NIC flag.
authorMichael Chan <mchan@broadcom.com>
Thu, 7 Dec 2006 08:21:14 +0000 (00:21 -0800)
committerDavid S. Miller <davem@davemloft.net>
Thu, 7 Dec 2006 08:21:14 +0000 (00:21 -0800)
Add Tg3_FLG2_IS_NIC flag to unambiguously determine whether the
device is NIC or onboard.  Previously, the EEPROM_WRITE_PROT flag was
overloaded to also mean onboard.  With the separation, we can
support some devices that are onboard but do not use eeprom write
protect.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/tg3.c
drivers/net/tg3.h
include/linux/pci_ids.h

index 5514828b792993f3330b79d8d3abdba0b7326c71..16bc05fe531f80eeaf80b5bfa9cd62074a7501e0 100644 (file)
@@ -1062,7 +1062,7 @@ static void tg3_frob_aux_power(struct tg3 *tp)
 {
        struct tg3 *tp_peer = tp;
 
-       if ((tp->tg3_flags & TG3_FLAG_EEPROM_WRITE_PROT) != 0)
+       if ((tp->tg3_flags2 & TG3_FLG2_IS_NIC) == 0)
                return;
 
        if ((GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5704) ||
@@ -1213,8 +1213,8 @@ static int tg3_set_power_state(struct tg3 *tp, pci_power_t state)
                                      power_control);
                udelay(100);    /* Delay after power state change */
 
-               /* Switch out of Vaux if it is not a LOM */
-               if (!(tp->tg3_flags & TG3_FLAG_EEPROM_WRITE_PROT))
+               /* Switch out of Vaux if it is a NIC */
+               if (tp->tg3_flags2 & TG3_FLG2_IS_NIC)
                        tw32_wait_f(GRC_LOCAL_CTRL, tp->grc_local_ctrl, 100);
 
                return 0;
@@ -6397,16 +6397,17 @@ static int tg3_reset_hw(struct tg3 *tp, int reset_phy)
        udelay(40);
 
        /* tp->grc_local_ctrl is partially set up during tg3_get_invariants().
-        * If TG3_FLAG_EEPROM_WRITE_PROT is set, we should read the
+        * If TG3_FLG2_IS_NIC is zero, we should read the
         * register to preserve the GPIO settings for LOMs. The GPIOs,
         * whether used as inputs or outputs, are set by boot code after
         * reset.
         */
-       if (tp->tg3_flags & TG3_FLAG_EEPROM_WRITE_PROT) {
+       if (!(tp->tg3_flags2 & TG3_FLG2_IS_NIC)) {
                u32 gpio_mask;
 
-               gpio_mask = GRC_LCLCTRL_GPIO_OE0 | GRC_LCLCTRL_GPIO_OE2 |
-                           GRC_LCLCTRL_GPIO_OUTPUT0 | GRC_LCLCTRL_GPIO_OUTPUT2;
+               gpio_mask = GRC_LCLCTRL_GPIO_OE0 | GRC_LCLCTRL_GPIO_OE1 |
+                           GRC_LCLCTRL_GPIO_OE2 | GRC_LCLCTRL_GPIO_OUTPUT0 |
+                           GRC_LCLCTRL_GPIO_OUTPUT1 | GRC_LCLCTRL_GPIO_OUTPUT2;
 
                if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5752)
                        gpio_mask |= GRC_LCLCTRL_GPIO_OE3 |
@@ -6418,8 +6419,9 @@ static int tg3_reset_hw(struct tg3 *tp, int reset_phy)
                tp->grc_local_ctrl |= tr32(GRC_LOCAL_CTRL) & gpio_mask;
 
                /* GPIO1 must be driven high for eeprom write protect */
-               tp->grc_local_ctrl |= (GRC_LCLCTRL_GPIO_OE1 |
-                                      GRC_LCLCTRL_GPIO_OUTPUT1);
+               if (tp->tg3_flags & TG3_FLAG_EEPROM_WRITE_PROT)
+                       tp->grc_local_ctrl |= (GRC_LCLCTRL_GPIO_OE1 |
+                                              GRC_LCLCTRL_GPIO_OUTPUT1);
        }
        tw32_f(GRC_LOCAL_CTRL, tp->grc_local_ctrl);
        udelay(100);
@@ -9963,8 +9965,10 @@ static void __devinit tg3_get_eeprom_hw_cfg(struct tg3 *tp)
        tp->tg3_flags |= TG3_FLAG_EEPROM_WRITE_PROT;
 
        if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5906) {
-               if (!(tr32(PCIE_TRANSACTION_CFG) & PCIE_TRANS_CFG_LOM))
+               if (!(tr32(PCIE_TRANSACTION_CFG) & PCIE_TRANS_CFG_LOM)) {
                        tp->tg3_flags &= ~TG3_FLAG_EEPROM_WRITE_PROT;
+                       tp->tg3_flags2 |= TG3_FLG2_IS_NIC;
+               }
                return;
        }
 
@@ -10064,10 +10068,17 @@ static void __devinit tg3_get_eeprom_hw_cfg(struct tg3 *tp)
                    tp->pdev->subsystem_vendor == PCI_VENDOR_ID_DELL)
                        tp->led_ctrl = LED_CTRL_MODE_PHY_2;
 
-               if (nic_cfg & NIC_SRAM_DATA_CFG_EEPROM_WP)
+               if (nic_cfg & NIC_SRAM_DATA_CFG_EEPROM_WP) {
                        tp->tg3_flags |= TG3_FLAG_EEPROM_WRITE_PROT;
-               else
+                       if ((tp->pdev->subsystem_vendor ==
+                            PCI_VENDOR_ID_ARIMA) &&
+                           (tp->pdev->subsystem_device == 0x205a ||
+                            tp->pdev->subsystem_device == 0x2063))
+                               tp->tg3_flags &= ~TG3_FLAG_EEPROM_WRITE_PROT;
+               } else {
                        tp->tg3_flags &= ~TG3_FLAG_EEPROM_WRITE_PROT;
+                       tp->tg3_flags2 |= TG3_FLG2_IS_NIC;
+               }
 
                if (nic_cfg & NIC_SRAM_DATA_CFG_ASF_ENABLE) {
                        tp->tg3_flags |= TG3_FLAG_ENABLE_ASF;
@@ -10693,7 +10704,7 @@ static int __devinit tg3_get_invariants(struct tg3 *tp)
                tp->tg3_flags |= TG3_FLAG_SRAM_USE_CONFIG;
 
        /* Get eeprom hw config before calling tg3_set_power_state().
-        * In particular, the TG3_FLAG_EEPROM_WRITE_PROT flag must be
+        * In particular, the TG3_FLG2_IS_NIC flag must be
         * determined before calling tg3_set_power_state() so that
         * we know whether or not to switch out of Vaux power.
         * When the flag is set, it means that GPIO1 is used for eeprom
index 92f53000bce69f2895dad2183ac37013de7e58cb..dfaf4ed127bd712378168eb1b64b82b4bd5f39ef 100644 (file)
@@ -2233,6 +2233,7 @@ struct tg3 {
 #define TG3_FLG2_PCI_EXPRESS           0x00000200
 #define TG3_FLG2_ASF_NEW_HANDSHAKE     0x00000400
 #define TG3_FLG2_HW_AUTONEG            0x00000800
+#define TG3_FLG2_IS_NIC                        0x00001000
 #define TG3_FLG2_PHY_SERDES            0x00002000
 #define TG3_FLG2_CAPACITIVE_COUPLING   0x00004000
 #define TG3_FLG2_FLASH                 0x00008000
index edddcce68b94291c731ee75d84a0ed8cb2964910..ebc597d57242dea9eb4f5a9f84f40b97800a22e8 100644 (file)
 #define PCI_DEVICE_ID_FARSITE_TE1       0x1610
 #define PCI_DEVICE_ID_FARSITE_TE1C      0x1612
 
+#define PCI_VENDOR_ID_ARIMA            0x161f
+
 #define PCI_VENDOR_ID_SIBYTE           0x166d
 #define PCI_DEVICE_ID_BCM1250_PCI      0x0001
 #define PCI_DEVICE_ID_BCM1250_HT       0x0002