ASoC and non-ASoC drivers for ACLINK on PXA share lot's of common code.
Move all common code into separate module snd-pxa2xx-lib.
[Fixed handing of SND_AC97_CODEC in Kconfig and some checkpatch warnings
-- broonie]
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
--- /dev/null
+#ifndef PXA2XX_LIB_H
+#define PXA2XX_LIB_H
+
+#include <linux/platform_device.h>
+#include <sound/ac97_codec.h>
+
+extern unsigned short pxa2xx_ac97_read(struct snd_ac97 *ac97, unsigned short reg);
+extern void pxa2xx_ac97_write(struct snd_ac97 *ac97, unsigned short reg, unsigned short val);
+
+extern bool pxa2xx_ac97_try_warm_reset(struct snd_ac97 *ac97);
+extern bool pxa2xx_ac97_try_cold_reset(struct snd_ac97 *ac97);
+extern void pxa2xx_ac97_finish_reset(struct snd_ac97 *ac97);
+
+extern int pxa2xx_ac97_hw_suspend(void);
+extern int pxa2xx_ac97_hw_resume(void);
+
+extern int pxa2xx_ac97_hw_probe(struct platform_device *dev);
+extern void pxa2xx_ac97_hw_remove(struct platform_device *dev);
+
+#endif
tristate
select SND_PCM
+config SND_PXA2XX_LIB
+ tristate
+ select SND_AC97_CODEC
+
config SND_PXA2XX_AC97
tristate "AC97 driver for the Intel PXA2xx chip"
depends on ARCH_PXA
select SND_PXA2XX_PCM
select SND_AC97_CODEC
+ select SND_PXA2XX_LIB
help
Say Y or M if you want to support any AC97 codec attached to
the PXA2xx AC97 interface.
obj-$(CONFIG_SND_PXA2XX_PCM) += snd-pxa2xx-pcm.o
snd-pxa2xx-pcm-objs := pxa2xx-pcm.o
+obj-$(CONFIG_SND_PXA2XX_LIB) += snd-pxa2xx-lib.o
+snd-pxa2xx-lib-objs := pxa2xx-ac97-lib.o
+
obj-$(CONFIG_SND_PXA2XX_AC97) += snd-pxa2xx-ac97.o
snd-pxa2xx-ac97-objs := pxa2xx-ac97.o
--- /dev/null
+/*
+ * Based on sound/arm/pxa2xx-ac97.c and sound/soc/pxa/pxa2xx-ac97.c
+ * which contain:
+ *
+ * Author: Nicolas Pitre
+ * Created: Dec 02, 2004
+ * Copyright: MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+
+#include <sound/ac97_codec.h>
+#include <sound/pxa2xx-lib.h>
+
+#include <asm/irq.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/audio.h>
+
+static DEFINE_MUTEX(car_mutex);
+static DECLARE_WAIT_QUEUE_HEAD(gsr_wq);
+static volatile long gsr_bits;
+static struct clk *ac97_clk;
+#ifdef CONFIG_PXA27x
+static struct clk *ac97conf_clk;
+#endif
+
+/*
+ * Beware PXA27x bugs:
+ *
+ * o Slot 12 read from modem space will hang controller.
+ * o CDONE, SDONE interrupt fails after any slot 12 IO.
+ *
+ * We therefore have an hybrid approach for waiting on SDONE (interrupt or
+ * 1 jiffy timeout if interrupt never comes).
+ */
+
+unsigned short pxa2xx_ac97_read(struct snd_ac97 *ac97, unsigned short reg)
+{
+ unsigned short val = -1;
+ volatile u32 *reg_addr;
+
+ mutex_lock(&car_mutex);
+
+ /* set up primary or secondary codec space */
+#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
+ reg_addr = (ac97->num & 1) ? &SAC_REG_BASE : &PAC_REG_BASE;
+#else
+ if (reg == AC97_GPIO_STATUS)
+ reg_addr = ac97->num ? &SMC_REG_BASE : &PMC_REG_BASE;
+ else
+ reg_addr = ac97->num ? &SAC_REG_BASE : &PAC_REG_BASE;
+#endif
+ reg_addr += (reg >> 1);
+
+ /* start read access across the ac97 link */
+ GSR = GSR_CDONE | GSR_SDONE;
+ gsr_bits = 0;
+ val = *reg_addr;
+ if (reg == AC97_GPIO_STATUS)
+ goto out;
+ if (wait_event_timeout(gsr_wq, (GSR | gsr_bits) & GSR_SDONE, 1) <= 0 &&
+ !((GSR | gsr_bits) & GSR_SDONE)) {
+ printk(KERN_ERR "%s: read error (ac97_reg=%d GSR=%#lx)\n",
+ __func__, reg, GSR | gsr_bits);
+ val = -1;
+ goto out;
+ }
+
+ /* valid data now */
+ GSR = GSR_CDONE | GSR_SDONE;
+ gsr_bits = 0;
+ val = *reg_addr;
+ /* but we've just started another cycle... */
+ wait_event_timeout(gsr_wq, (GSR | gsr_bits) & GSR_SDONE, 1);
+
+out: mutex_unlock(&car_mutex);
+ return val;
+}
+EXPORT_SYMBOL_GPL(pxa2xx_ac97_read);
+
+void pxa2xx_ac97_write(struct snd_ac97 *ac97, unsigned short reg,
+ unsigned short val)
+{
+ volatile u32 *reg_addr;
+
+ mutex_lock(&car_mutex);
+
+ /* set up primary or secondary codec space */
+#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
+ reg_addr = (ac97->num & 1) ? &SAC_REG_BASE : &PAC_REG_BASE;
+#else
+ if (reg == AC97_GPIO_STATUS)
+ reg_addr = ac97->num ? &SMC_REG_BASE : &PMC_REG_BASE;
+ else
+ reg_addr = ac97->num ? &SAC_REG_BASE : &PAC_REG_BASE;
+#endif
+ reg_addr += (reg >> 1);
+
+ GSR = GSR_CDONE | GSR_SDONE;
+ gsr_bits = 0;
+ *reg_addr = val;
+ if (wait_event_timeout(gsr_wq, (GSR | gsr_bits) & GSR_CDONE, 1) <= 0 &&
+ !((GSR | gsr_bits) & GSR_CDONE))
+ printk(KERN_ERR "%s: write error (ac97_reg=%d GSR=%#lx)\n",
+ __func__, reg, GSR | gsr_bits);
+
+ mutex_unlock(&car_mutex);
+}
+EXPORT_SYMBOL_GPL(pxa2xx_ac97_write);
+
+bool pxa2xx_ac97_try_warm_reset(struct snd_ac97 *ac97)
+{
+#ifdef CONFIG_PXA3xx
+ int timeout = 100;
+#endif
+ gsr_bits = 0;
+
+#ifdef CONFIG_PXA27x
+ /* warm reset broken on Bulverde,
+ so manually keep AC97 reset high */
+ pxa_gpio_mode(113 | GPIO_OUT | GPIO_DFLT_HIGH);
+ udelay(10);
+ GCR |= GCR_WARM_RST;
+ pxa_gpio_mode(113 | GPIO_ALT_FN_2_OUT);
+ udelay(500);
+#elif defined(CONFIG_PXA3xx)
+ /* Can't use interrupts */
+ GCR |= GCR_WARM_RST;
+ while (!((GSR | gsr_bits) & (GSR_PCR | GSR_SCR)) && timeout--)
+ mdelay(1);
+#else
+ GCR |= GCR_WARM_RST | GCR_PRIRDY_IEN | GCR_SECRDY_IEN;
+ wait_event_timeout(gsr_wq, gsr_bits & (GSR_PCR | GSR_SCR), 1);
+#endif
+
+ if (!((GSR | gsr_bits) & (GSR_PCR | GSR_SCR))) {
+ printk(KERN_INFO "%s: warm reset timeout (GSR=%#lx)\n",
+ __func__, gsr_bits);
+
+ return false;
+ }
+
+ return true;
+}
+EXPORT_SYMBOL_GPL(pxa2xx_ac97_try_warm_reset);
+
+bool pxa2xx_ac97_try_cold_reset(struct snd_ac97 *ac97)
+{
+#ifdef CONFIG_PXA3xx
+ int timeout = 1000;
+
+ /* Hold CLKBPB for 100us */
+ GCR = 0;
+ GCR = GCR_CLKBPB;
+ udelay(100);
+ GCR = 0;
+#endif
+
+ GCR &= GCR_COLD_RST; /* clear everything but nCRST */
+ GCR &= ~GCR_COLD_RST; /* then assert nCRST */
+
+ gsr_bits = 0;
+#ifdef CONFIG_PXA27x
+ /* PXA27x Developers Manual section 13.5.2.2.1 */
+ clk_enable(ac97conf_clk);
+ udelay(5);
+ clk_disable(ac97conf_clk);
+ GCR = GCR_COLD_RST;
+ udelay(50);
+#elif defined(CONFIG_PXA3xx)
+ /* Can't use interrupts on PXA3xx */
+ GCR &= ~(GCR_PRIRDY_IEN|GCR_SECRDY_IEN);
+
+ GCR = GCR_WARM_RST | GCR_COLD_RST;
+ while (!(GSR & (GSR_PCR | GSR_SCR)) && timeout--)
+ mdelay(10);
+#else
+ GCR = GCR_COLD_RST;
+ GCR |= GCR_CDONE_IE|GCR_SDONE_IE;
+ wait_event_timeout(gsr_wq, gsr_bits & (GSR_PCR | GSR_SCR), 1);
+#endif
+
+ if (!((GSR | gsr_bits) & (GSR_PCR | GSR_SCR))) {
+ printk(KERN_INFO "%s: cold reset timeout (GSR=%#lx)\n",
+ __func__, gsr_bits);
+
+ return false;
+ }
+
+ return true;
+}
+EXPORT_SYMBOL_GPL(pxa2xx_ac97_try_cold_reset);
+
+
+void pxa2xx_ac97_finish_reset(struct snd_ac97 *ac97)
+{
+ GCR &= ~(GCR_PRIRDY_IEN|GCR_SECRDY_IEN);
+ GCR |= GCR_SDONE_IE|GCR_CDONE_IE;
+}
+EXPORT_SYMBOL_GPL(pxa2xx_ac97_finish_reset);
+
+static irqreturn_t pxa2xx_ac97_irq(int irq, void *dev_id)
+{
+ long status;
+
+ status = GSR;
+ if (status) {
+ GSR = status;
+ gsr_bits |= status;
+ wake_up(&gsr_wq);
+
+#ifdef CONFIG_PXA27x
+ /* Although we don't use those we still need to clear them
+ since they tend to spuriously trigger when MMC is used
+ (hardware bug? go figure)... */
+ MISR = MISR_EOC;
+ PISR = PISR_EOC;
+ MCSR = MCSR_EOC;
+#endif
+
+ return IRQ_HANDLED;
+ }
+
+ return IRQ_NONE;
+}
+
+#ifdef CONFIG_PM
+int pxa2xx_ac97_hw_suspend(void)
+{
+ GCR |= GCR_ACLINK_OFF;
+ clk_disable(ac97_clk);
+ return 0;
+}
+EXPORT_SYMBOL_GPL(pxa2xx_ac97_hw_suspend);
+
+int pxa2xx_ac97_hw_resume(void)
+{
+ pxa_gpio_mode(GPIO31_SYNC_AC97_MD);
+ pxa_gpio_mode(GPIO30_SDATA_OUT_AC97_MD);
+ pxa_gpio_mode(GPIO28_BITCLK_AC97_MD);
+ pxa_gpio_mode(GPIO29_SDATA_IN_AC97_MD);
+#ifdef CONFIG_PXA27x
+ /* Use GPIO 113 as AC97 Reset on Bulverde */
+ pxa_gpio_mode(113 | GPIO_ALT_FN_2_OUT);
+#endif
+ clk_enable(ac97_clk);
+ return 0;
+}
+EXPORT_SYMBOL_GPL(pxa2xx_ac97_hw_resume);
+#endif
+
+int __devinit pxa2xx_ac97_hw_probe(struct platform_device *dev)
+{
+ int ret;
+
+ ret = request_irq(IRQ_AC97, pxa2xx_ac97_irq, 0, "AC97", NULL);
+ if (ret < 0)
+ goto err;
+
+ pxa_gpio_mode(GPIO31_SYNC_AC97_MD);
+ pxa_gpio_mode(GPIO30_SDATA_OUT_AC97_MD);
+ pxa_gpio_mode(GPIO28_BITCLK_AC97_MD);
+ pxa_gpio_mode(GPIO29_SDATA_IN_AC97_MD);
+#ifdef CONFIG_PXA27x
+ /* Use GPIO 113 as AC97 Reset on Bulverde */
+ pxa_gpio_mode(113 | GPIO_ALT_FN_2_OUT);
+ ac97conf_clk = clk_get(&dev->dev, "AC97CONFCLK");
+ if (IS_ERR(ac97conf_clk)) {
+ ret = PTR_ERR(ac97conf_clk);
+ ac97conf_clk = NULL;
+ goto err_irq;
+ }
+#endif
+
+ ac97_clk = clk_get(&dev->dev, "AC97CLK");
+ if (IS_ERR(ac97_clk)) {
+ ret = PTR_ERR(ac97_clk);
+ ac97_clk = NULL;
+ goto err_irq;
+ }
+
+ return clk_enable(ac97_clk);
+
+err_irq:
+ GCR |= GCR_ACLINK_OFF;
+#ifdef CONFIG_PXA27x
+ if (ac97conf_clk) {
+ clk_put(ac97conf_clk);
+ ac97conf_clk = NULL;
+ }
+#endif
+ free_irq(IRQ_AC97, NULL);
+err:
+ return ret;
+}
+EXPORT_SYMBOL_GPL(pxa2xx_ac97_hw_probe);
+
+void pxa2xx_ac97_hw_remove(struct platform_device *dev)
+{
+ GCR |= GCR_ACLINK_OFF;
+ free_irq(IRQ_AC97, NULL);
+#ifdef CONFIG_PXA27x
+ clk_put(ac97conf_clk);
+ ac97conf_clk = NULL;
+#endif
+ clk_disable(ac97_clk);
+ clk_put(ac97_clk);
+ ac97_clk = NULL;
+}
+EXPORT_SYMBOL_GPL(pxa2xx_ac97_hw_remove);
+
+MODULE_AUTHOR("Nicolas Pitre");
+MODULE_DESCRIPTION("Intel/Marvell PXA sound library");
+MODULE_LICENSE("GPL");
+
#include <linux/init.h>
#include <linux/module.h>
-#include <linux/kernel.h>
#include <linux/platform_device.h>
-#include <linux/interrupt.h>
-#include <linux/wait.h>
-#include <linux/clk.h>
-#include <linux/delay.h>
#include <sound/core.h>
#include <sound/pcm.h>
#include <sound/ac97_codec.h>
#include <sound/initval.h>
+#include <sound/pxa2xx-lib.h>
-#include <asm/irq.h>
-#include <linux/mutex.h>
#include <mach/hardware.h>
#include <mach/pxa-regs.h>
-#include <mach/pxa2xx-gpio.h>
#include <mach/audio.h>
#include "pxa2xx-pcm.h"
-
-static DEFINE_MUTEX(car_mutex);
-static DECLARE_WAIT_QUEUE_HEAD(gsr_wq);
-static volatile long gsr_bits;
-static struct clk *ac97_clk;
-#ifdef CONFIG_PXA27x
-static struct clk *ac97conf_clk;
-#endif
-
-/*
- * Beware PXA27x bugs:
- *
- * o Slot 12 read from modem space will hang controller.
- * o CDONE, SDONE interrupt fails after any slot 12 IO.
- *
- * We therefore have an hybrid approach for waiting on SDONE (interrupt or
- * 1 jiffy timeout if interrupt never comes).
- */
-
-static unsigned short pxa2xx_ac97_read(struct snd_ac97 *ac97, unsigned short reg)
-{
- unsigned short val = -1;
- volatile u32 *reg_addr;
-
- mutex_lock(&car_mutex);
-
- /* set up primary or secondary codec space */
- reg_addr = (ac97->num & 1) ? &SAC_REG_BASE : &PAC_REG_BASE;
- reg_addr += (reg >> 1);
-
- /* start read access across the ac97 link */
- GSR = GSR_CDONE | GSR_SDONE;
- gsr_bits = 0;
- val = *reg_addr;
- if (reg == AC97_GPIO_STATUS)
- goto out;
- if (wait_event_timeout(gsr_wq, (GSR | gsr_bits) & GSR_SDONE, 1) <= 0 &&
- !((GSR | gsr_bits) & GSR_SDONE)) {
- printk(KERN_ERR "%s: read error (ac97_reg=%d GSR=%#lx)\n",
- __func__, reg, GSR | gsr_bits);
- val = -1;
- goto out;
- }
-
- /* valid data now */
- GSR = GSR_CDONE | GSR_SDONE;
- gsr_bits = 0;
- val = *reg_addr;
- /* but we've just started another cycle... */
- wait_event_timeout(gsr_wq, (GSR | gsr_bits) & GSR_SDONE, 1);
-
-out: mutex_unlock(&car_mutex);
- return val;
-}
-
-static void pxa2xx_ac97_write(struct snd_ac97 *ac97, unsigned short reg, unsigned short val)
-{
- volatile u32 *reg_addr;
-
- mutex_lock(&car_mutex);
-
- /* set up primary or secondary codec space */
- reg_addr = (ac97->num & 1) ? &SAC_REG_BASE : &PAC_REG_BASE;
- reg_addr += (reg >> 1);
-
- GSR = GSR_CDONE | GSR_SDONE;
- gsr_bits = 0;
- *reg_addr = val;
- if (wait_event_timeout(gsr_wq, (GSR | gsr_bits) & GSR_CDONE, 1) <= 0 &&
- !((GSR | gsr_bits) & GSR_CDONE))
- printk(KERN_ERR "%s: write error (ac97_reg=%d GSR=%#lx)\n",
- __func__, reg, GSR | gsr_bits);
-
- mutex_unlock(&car_mutex);
-}
-
static void pxa2xx_ac97_reset(struct snd_ac97 *ac97)
{
- /* First, try cold reset */
-#ifdef CONFIG_PXA3xx
- int timeout;
-
- /* Hold CLKBPB for 100us */
- GCR = 0;
- GCR = GCR_CLKBPB;
- udelay(100);
- GCR = 0;
-#endif
-
- GCR &= GCR_COLD_RST; /* clear everything but nCRST */
- GCR &= ~GCR_COLD_RST; /* then assert nCRST */
-
- gsr_bits = 0;
-#ifdef CONFIG_PXA27x
- /* PXA27x Developers Manual section 13.5.2.2.1 */
- clk_enable(ac97conf_clk);
- udelay(5);
- clk_disable(ac97conf_clk);
- GCR = GCR_COLD_RST;
- udelay(50);
-#elif defined(CONFIG_PXA3xx)
- timeout = 1000;
- /* Can't use interrupts on PXA3xx */
- GCR &= ~(GCR_PRIRDY_IEN|GCR_SECRDY_IEN);
-
- GCR = GCR_WARM_RST | GCR_COLD_RST;
- while (!(GSR & (GSR_PCR | GSR_SCR)) && timeout--)
- mdelay(10);
-#else
- GCR = GCR_COLD_RST;
- GCR |= GCR_CDONE_IE|GCR_SDONE_IE;
- wait_event_timeout(gsr_wq, gsr_bits & (GSR_PCR | GSR_SCR), 1);
-#endif
-
- if (!((GSR | gsr_bits) & (GSR_PCR | GSR_SCR))) {
- printk(KERN_INFO "%s: cold reset timeout (GSR=%#lx)\n",
- __func__, gsr_bits);
-
- /* let's try warm reset */
- gsr_bits = 0;
-#ifdef CONFIG_PXA27x
- /* warm reset broken on Bulverde,
- so manually keep AC97 reset high */
- pxa_gpio_mode(113 | GPIO_OUT | GPIO_DFLT_HIGH);
- udelay(10);
- GCR |= GCR_WARM_RST;
- pxa_gpio_mode(113 | GPIO_ALT_FN_2_OUT);
- udelay(500);
-#elif defined(CONFIG_PXA3xx)
- timeout = 100;
- /* Can't use interrupts */
- GCR |= GCR_WARM_RST;
- while (!((GSR | gsr_bits) & (GSR_PCR | GSR_SCR)) && timeout--)
- mdelay(1);
-#else
- GCR |= GCR_WARM_RST|GCR_PRIRDY_IEN|GCR_SECRDY_IEN;
- wait_event_timeout(gsr_wq, gsr_bits & (GSR_PCR | GSR_SCR), 1);
-#endif
-
- if (!((GSR | gsr_bits) & (GSR_PCR | GSR_SCR)))
- printk(KERN_INFO "%s: warm reset timeout (GSR=%#lx)\n",
- __func__, gsr_bits);
- }
-
- GCR &= ~(GCR_PRIRDY_IEN|GCR_SECRDY_IEN);
- GCR |= GCR_SDONE_IE|GCR_CDONE_IE;
-}
-
-static irqreturn_t pxa2xx_ac97_irq(int irq, void *dev_id)
-{
- long status;
-
- status = GSR;
- if (status) {
- GSR = status;
- gsr_bits |= status;
- wake_up(&gsr_wq);
-
-#ifdef CONFIG_PXA27x
- /* Although we don't use those we still need to clear them
- since they tend to spuriously trigger when MMC is used
- (hardware bug? go figure)... */
- MISR = MISR_EOC;
- PISR = PISR_EOC;
- MCSR = MCSR_EOC;
-#endif
-
- return IRQ_HANDLED;
+ if (!pxa2xx_ac97_try_cold_reset(ac97)) {
+ pxa2xx_ac97_try_warm_reset(ac97);
}
- return IRQ_NONE;
+ pxa2xx_ac97_finish_reset(ac97);
}
static struct snd_ac97_bus_ops pxa2xx_ac97_ops = {
snd_ac97_suspend(pxa2xx_ac97_ac97);
if (platform_ops && platform_ops->suspend)
platform_ops->suspend(platform_ops->priv);
- GCR |= GCR_ACLINK_OFF;
- clk_disable(ac97_clk);
- return 0;
+ return pxa2xx_ac97_hw_suspend();
}
static int pxa2xx_ac97_do_resume(struct snd_card *card)
{
pxa2xx_audio_ops_t *platform_ops = card->dev->platform_data;
+ int rc;
+
+ rc = pxa2xx_ac97_hw_resume();
+ if (rc)
+ return rc;
- clk_enable(ac97_clk);
if (platform_ops && platform_ops->resume)
platform_ops->resume(platform_ops->priv);
snd_ac97_resume(pxa2xx_ac97_ac97);
if (ret)
goto err;
- ret = request_irq(IRQ_AC97, pxa2xx_ac97_irq, 0, "AC97", NULL);
- if (ret < 0)
- goto err;
-
- pxa_gpio_mode(GPIO31_SYNC_AC97_MD);
- pxa_gpio_mode(GPIO30_SDATA_OUT_AC97_MD);
- pxa_gpio_mode(GPIO28_BITCLK_AC97_MD);
- pxa_gpio_mode(GPIO29_SDATA_IN_AC97_MD);
-#ifdef CONFIG_PXA27x
- /* Use GPIO 113 as AC97 Reset on Bulverde */
- pxa_gpio_mode(113 | GPIO_ALT_FN_2_OUT);
- ac97conf_clk = clk_get(&dev->dev, "AC97CONFCLK");
- if (IS_ERR(ac97conf_clk)) {
- ret = PTR_ERR(ac97conf_clk);
- ac97conf_clk = NULL;
- goto err;
- }
-#endif
-
- ac97_clk = clk_get(&dev->dev, "AC97CLK");
- if (IS_ERR(ac97_clk)) {
- ret = PTR_ERR(ac97_clk);
- ac97_clk = NULL;
+ ret = pxa2xx_ac97_hw_probe(dev);
+ if (ret)
goto err;
- }
- clk_enable(ac97_clk);
ret = snd_ac97_bus(card, 0, &pxa2xx_ac97_ops, NULL, &ac97_bus);
if (ret)
- goto err;
+ goto err_remove;
memset(&ac97_template, 0, sizeof(ac97_template));
ret = snd_ac97_mixer(ac97_bus, &ac97_template, &pxa2xx_ac97_ac97);
if (ret)
- goto err;
+ goto err_remove;
snprintf(card->shortname, sizeof(card->shortname),
"%s", snd_ac97_get_short_name(pxa2xx_ac97_ac97));
return 0;
}
- err:
+err_remove:
+ pxa2xx_ac97_hw_remove(dev);
+err:
if (card)
snd_card_free(card);
- if (ac97_clk) {
- GCR |= GCR_ACLINK_OFF;
- free_irq(IRQ_AC97, NULL);
- clk_disable(ac97_clk);
- clk_put(ac97_clk);
- ac97_clk = NULL;
- }
-#ifdef CONFIG_PXA27x
- if (ac97conf_clk) {
- clk_put(ac97conf_clk);
- ac97conf_clk = NULL;
- }
-#endif
return ret;
}
if (card) {
snd_card_free(card);
platform_set_drvdata(dev, NULL);
- GCR |= GCR_ACLINK_OFF;
- free_irq(IRQ_AC97, NULL);
- clk_disable(ac97_clk);
- clk_put(ac97_clk);
- ac97_clk = NULL;
-#ifdef CONFIG_PXA27x
- clk_put(ac97conf_clk);
- ac97conf_clk = NULL;
-#endif
+ pxa2xx_ac97_hw_remove(dev);
}
return 0;
config SND_PXA2XX_SOC_AC97
tristate
select AC97_BUS
+ select SND_ARM
+ select SND_PXA2XX_LIB
select SND_SOC_AC97_BUS
config SND_PXA2XX_SOC_I2S
#include <linux/init.h>
#include <linux/module.h>
#include <linux/platform_device.h>
-#include <linux/interrupt.h>
-#include <linux/wait.h>
-#include <linux/clk.h>
-#include <linux/delay.h>
#include <sound/core.h>
-#include <sound/pcm.h>
#include <sound/ac97_codec.h>
-#include <sound/initval.h>
#include <sound/soc.h>
+#include <sound/pxa2xx-lib.h>
-#include <asm/irq.h>
-#include <linux/mutex.h>
#include <mach/hardware.h>
#include <mach/pxa-regs.h>
-#include <mach/pxa2xx-gpio.h>
-#include <mach/audio.h>
#include "pxa2xx-pcm.h"
#include "pxa2xx-ac97.h"
-static DEFINE_MUTEX(car_mutex);
-static DECLARE_WAIT_QUEUE_HEAD(gsr_wq);
-static volatile long gsr_bits;
-static struct clk *ac97_clk;
-#ifdef CONFIG_PXA27x
-static struct clk *ac97conf_clk;
-#endif
-
-/*
- * Beware PXA27x bugs:
- *
- * o Slot 12 read from modem space will hang controller.
- * o CDONE, SDONE interrupt fails after any slot 12 IO.
- *
- * We therefore have an hybrid approach for waiting on SDONE (interrupt or
- * 1 jiffy timeout if interrupt never comes).
- */
-
-static unsigned short pxa2xx_ac97_read(struct snd_ac97 *ac97,
- unsigned short reg)
-{
- unsigned short val = -1;
- volatile u32 *reg_addr;
-
- mutex_lock(&car_mutex);
-
- /* set up primary or secondary codec/modem space */
-#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
- reg_addr = ac97->num ? &SAC_REG_BASE : &PAC_REG_BASE;
-#else
- if (reg == AC97_GPIO_STATUS)
- reg_addr = ac97->num ? &SMC_REG_BASE : &PMC_REG_BASE;
- else
- reg_addr = ac97->num ? &SAC_REG_BASE : &PAC_REG_BASE;
-#endif
- reg_addr += (reg >> 1);
-
-#ifndef CONFIG_PXA27x
- if (reg == AC97_GPIO_STATUS) {
- /* read from controller cache */
- val = *reg_addr;
- goto out;
- }
-#endif
-
- /* start read access across the ac97 link */
- GSR = GSR_CDONE | GSR_SDONE;
- gsr_bits = 0;
- val = *reg_addr;
-
- wait_event_timeout(gsr_wq, (GSR | gsr_bits) & GSR_SDONE, 1);
- if (!((GSR | gsr_bits) & GSR_SDONE)) {
- printk(KERN_ERR "%s: read error (ac97_reg=%x GSR=%#lx)\n",
- __func__, reg, GSR | gsr_bits);
- val = -1;
- goto out;
- }
-
- /* valid data now */
- GSR = GSR_CDONE | GSR_SDONE;
- gsr_bits = 0;
- val = *reg_addr;
- /* but we've just started another cycle... */
- wait_event_timeout(gsr_wq, (GSR | gsr_bits) & GSR_SDONE, 1);
-
-out: mutex_unlock(&car_mutex);
- return val;
-}
-
-static void pxa2xx_ac97_write(struct snd_ac97 *ac97, unsigned short reg,
- unsigned short val)
-{
- volatile u32 *reg_addr;
-
- mutex_lock(&car_mutex);
-
- /* set up primary or secondary codec/modem space */
-#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
- reg_addr = ac97->num ? &SAC_REG_BASE : &PAC_REG_BASE;
-#else
- if (reg == AC97_GPIO_STATUS)
- reg_addr = ac97->num ? &SMC_REG_BASE : &PMC_REG_BASE;
- else
- reg_addr = ac97->num ? &SAC_REG_BASE : &PAC_REG_BASE;
-#endif
- reg_addr += (reg >> 1);
-
- GSR = GSR_CDONE | GSR_SDONE;
- gsr_bits = 0;
- *reg_addr = val;
- wait_event_timeout(gsr_wq, (GSR | gsr_bits) & GSR_CDONE, 1);
- if (!((GSR | gsr_bits) & GSR_CDONE))
- printk(KERN_ERR "%s: write error (ac97_reg=%x GSR=%#lx)\n",
- __func__, reg, GSR | gsr_bits);
-
- mutex_unlock(&car_mutex);
-}
-
static void pxa2xx_ac97_warm_reset(struct snd_ac97 *ac97)
{
-#ifdef CONFIG_PXA3xx
- int timeout = 100;
-#endif
- gsr_bits = 0;
-
-#ifdef CONFIG_PXA27x
- /* warm reset broken on Bulverde,
- so manually keep AC97 reset high */
- pxa_gpio_mode(113 | GPIO_OUT | GPIO_DFLT_HIGH);
- udelay(10);
- GCR |= GCR_WARM_RST;
- pxa_gpio_mode(113 | GPIO_ALT_FN_2_OUT);
- udelay(500);
-#elif defined(CONFIG_PXA3xx)
- /* Can't use interrupts */
- GCR |= GCR_WARM_RST;
- while (!((GSR | gsr_bits) & (GSR_PCR | GSR_SCR)) && timeout--)
- mdelay(1);
-#else
- GCR |= GCR_WARM_RST | GCR_PRIRDY_IEN | GCR_SECRDY_IEN;
- wait_event_timeout(gsr_wq, gsr_bits & (GSR_PCR | GSR_SCR), 1);
-#endif
-
- if (!((GSR | gsr_bits) & (GSR_PCR | GSR_SCR)))
- printk(KERN_INFO "%s: warm reset timeout (GSR=%#lx)\n",
- __func__, gsr_bits);
+ pxa2xx_ac97_try_warm_reset(ac97);
- GCR &= ~(GCR_PRIRDY_IEN|GCR_SECRDY_IEN);
- GCR |= GCR_SDONE_IE|GCR_CDONE_IE;
+ pxa2xx_ac97_finish_reset(ac97);
}
static void pxa2xx_ac97_cold_reset(struct snd_ac97 *ac97)
{
-#ifdef CONFIG_PXA3xx
- int timeout = 1000;
-
- /* Hold CLKBPB for 100us */
- GCR = 0;
- GCR = GCR_CLKBPB;
- udelay(100);
- GCR = 0;
-#endif
+ pxa2xx_ac97_try_cold_reset(ac97);
- GCR &= GCR_COLD_RST; /* clear everything but nCRST */
- GCR &= ~GCR_COLD_RST; /* then assert nCRST */
-
- gsr_bits = 0;
-#ifdef CONFIG_PXA27x
- /* PXA27x Developers Manual section 13.5.2.2.1 */
- clk_enable(ac97conf_clk);
- udelay(5);
- clk_disable(ac97conf_clk);
- GCR = GCR_COLD_RST;
- udelay(50);
-#elif defined(CONFIG_PXA3xx)
- /* Can't use interrupts on PXA3xx */
- GCR &= ~(GCR_PRIRDY_IEN|GCR_SECRDY_IEN);
-
- GCR = GCR_WARM_RST | GCR_COLD_RST;
- while (!(GSR & (GSR_PCR | GSR_SCR)) && timeout--)
- mdelay(10);
-#else
- GCR = GCR_COLD_RST;
- GCR |= GCR_CDONE_IE|GCR_SDONE_IE;
- wait_event_timeout(gsr_wq, gsr_bits & (GSR_PCR | GSR_SCR), 1);
-#endif
-
- if (!((GSR | gsr_bits) & (GSR_PCR | GSR_SCR)))
- printk(KERN_INFO "%s: cold reset timeout (GSR=%#lx)\n",
- __func__, gsr_bits);
-
- GCR &= ~(GCR_PRIRDY_IEN|GCR_SECRDY_IEN);
- GCR |= GCR_SDONE_IE|GCR_CDONE_IE;
-}
-
-static irqreturn_t pxa2xx_ac97_irq(int irq, void *dev_id)
-{
- long status;
-
- status = GSR;
- if (status) {
- GSR = status;
- gsr_bits |= status;
- wake_up(&gsr_wq);
-
-#ifdef CONFIG_PXA27x
- /* Although we don't use those we still need to clear them
- since they tend to spuriously trigger when MMC is used
- (hardware bug? go figure)... */
- MISR = MISR_EOC;
- PISR = PISR_EOC;
- MCSR = MCSR_EOC;
-#endif
-
- return IRQ_HANDLED;
- }
-
- return IRQ_NONE;
+ pxa2xx_ac97_finish_reset(ac97);
}
struct snd_ac97_bus_ops soc_ac97_ops = {
static int pxa2xx_ac97_suspend(struct platform_device *pdev,
struct snd_soc_dai *dai)
{
- GCR |= GCR_ACLINK_OFF;
- clk_disable(ac97_clk);
- return 0;
+ return pxa2xx_ac97_hw_suspend();
}
static int pxa2xx_ac97_resume(struct platform_device *pdev,
struct snd_soc_dai *dai)
{
- pxa_gpio_mode(GPIO31_SYNC_AC97_MD);
- pxa_gpio_mode(GPIO30_SDATA_OUT_AC97_MD);
- pxa_gpio_mode(GPIO28_BITCLK_AC97_MD);
- pxa_gpio_mode(GPIO29_SDATA_IN_AC97_MD);
-#ifdef CONFIG_PXA27x
- /* Use GPIO 113 as AC97 Reset on Bulverde */
- pxa_gpio_mode(113 | GPIO_ALT_FN_2_OUT);
-#endif
- clk_enable(ac97_clk);
- return 0;
+ return pxa2xx_ac97_hw_resume();
}
#else
static int pxa2xx_ac97_probe(struct platform_device *pdev,
struct snd_soc_dai *dai)
{
- int ret;
-
- ret = request_irq(IRQ_AC97, pxa2xx_ac97_irq, IRQF_DISABLED, "AC97", NULL);
- if (ret < 0)
- goto err;
-
- pxa_gpio_mode(GPIO31_SYNC_AC97_MD);
- pxa_gpio_mode(GPIO30_SDATA_OUT_AC97_MD);
- pxa_gpio_mode(GPIO28_BITCLK_AC97_MD);
- pxa_gpio_mode(GPIO29_SDATA_IN_AC97_MD);
-#ifdef CONFIG_PXA27x
- /* Use GPIO 113 as AC97 Reset on Bulverde */
- pxa_gpio_mode(113 | GPIO_ALT_FN_2_OUT);
-
- ac97conf_clk = clk_get(&pdev->dev, "AC97CONFCLK");
- if (IS_ERR(ac97conf_clk)) {
- ret = PTR_ERR(ac97conf_clk);
- ac97conf_clk = NULL;
- goto err_irq;
- }
-#endif
- ac97_clk = clk_get(&pdev->dev, "AC97CLK");
- if (IS_ERR(ac97_clk)) {
- ret = PTR_ERR(ac97_clk);
- ac97_clk = NULL;
- goto err_irq;
- }
- clk_enable(ac97_clk);
- return 0;
-
- err_irq:
- GCR |= GCR_ACLINK_OFF;
-#ifdef CONFIG_PXA27x
- if (ac97conf_clk) {
- clk_put(ac97conf_clk);
- ac97conf_clk = NULL;
- }
-#endif
- free_irq(IRQ_AC97, NULL);
- err:
- return ret;
+ return pxa2xx_ac97_hw_probe(pdev);
}
static void pxa2xx_ac97_remove(struct platform_device *pdev,
struct snd_soc_dai *dai)
{
- GCR |= GCR_ACLINK_OFF;
- free_irq(IRQ_AC97, NULL);
-#ifdef CONFIG_PXA27x
- clk_put(ac97conf_clk);
- ac97conf_clk = NULL;
-#endif
- clk_disable(ac97_clk);
- clk_put(ac97_clk);
- ac97_clk = NULL;
+ pxa2xx_ac97_hw_remove(pdev);
}
static int pxa2xx_ac97_hw_params(struct snd_pcm_substream *substream,
projects / linux-2.6-omap-h63xx.git / commitdiff