mach-netx/time.c: codingstyle cleanup

To prevent cluttering the next patches with noop noise, do the cleanup
in this separate patch:

 - use tab to indent
 - break comments before column 80

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>

diff --git a/arch/arm/mach-netx/time.c b/arch/arm/mach-netx/time.c
index 7c540c1f01fab84a1fb797522649ca14427c1b4c..be833bd1048e788c7cef56b34458ade22707449a 100644 (file)
--- a/arch/arm/mach-netx/time.c
+++ b/arch/arm/mach-netx/time.c
@@ -42,9 +42,9 @@ netx_timer_interrupt(int irq, void *dev_id)
 }
 
 static struct irqaction netx_timer_irq = {
-       .name           = "NetX Timer Tick",
-       .flags          = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
-       .handler        = netx_timer_interrupt,
+       .name           = "NetX Timer Tick",
+       .flags          = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
+       .handler        = netx_timer_interrupt,
 };
 
 cycle_t netx_get_cycles(void)
@@ -53,11 +53,11 @@ cycle_t netx_get_cycles(void)
 }
 
 static struct clocksource clocksource_netx = {
-       .name           = "netx_timer",
+       .name           = "netx_timer",
        .rating         = 200,
        .read           = netx_get_cycles,
        .mask           = CLOCKSOURCE_MASK(32),
-       .shift          = 20,
+       .shift          = 20,
        .flags          = CLOCK_SOURCE_IS_CONTINUOUS,
 };
 
@@ -77,20 +77,22 @@ static void __init netx_timer_init(void)
        /* acknowledge interrupt */
        writel(COUNTER_BIT(0), NETX_GPIO_IRQ);
 
-       /* Enable the interrupt in the specific timer register and start timer */
+       /* Enable the interrupt in the specific timer
+        * register and start timer
+        */
        writel(COUNTER_BIT(0), NETX_GPIO_IRQ_ENABLE);
        writel(NETX_GPIO_COUNTER_CTRL_IRQ_EN | NETX_GPIO_COUNTER_CTRL_RUN,
-               NETX_GPIO_COUNTER_CTRL(0));
+                       NETX_GPIO_COUNTER_CTRL(0));
 
        setup_irq(NETX_IRQ_TIMER0, &netx_timer_irq);
 
        /* Setup timer one for clocksource */
-        writel(0, NETX_GPIO_COUNTER_CTRL(1));
-        writel(0, NETX_GPIO_COUNTER_CURRENT(1));
-        writel(0xFFFFFFFF, NETX_GPIO_COUNTER_MAX(1));
+       writel(0, NETX_GPIO_COUNTER_CTRL(1));
+       writel(0, NETX_GPIO_COUNTER_CURRENT(1));
+       writel(0xffffffff, NETX_GPIO_COUNTER_MAX(1));
 
-        writel(NETX_GPIO_COUNTER_CTRL_RUN,
-                NETX_GPIO_COUNTER_CTRL(1));
+       writel(NETX_GPIO_COUNTER_CTRL_RUN,
+                       NETX_GPIO_COUNTER_CTRL(1));
 
        clocksource_netx.mult =
                clocksource_hz2mult(CLOCK_TICK_RATE, clocksource_netx.shift);