[PATCH] PCI: do VIA IRQ fixup always, not just in PIC mode

At least some VIA chipsets require the fixup even in IO-APIC mode.

This was found and debugged with the patient assistance of Stian
Jordet <liste@jordet.nu> on an Asus CUV266-DLS motherboard.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index 637e9493034bce2bc6d35e9e43efa14decefe5ad..2194669300bfe5b6e198af9050931f47804afb55 100644 (file)
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -459,17 +459,6 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_APIC,
 #endif /* CONFIG_X86_IO_APIC */
 
 
-/*
- * Via 686A/B:  The PCI_INTERRUPT_LINE register for the on-chip
- * devices, USB0/1, AC97, MC97, and ACPI, has an unusual feature:
- * when written, it makes an internal connection to the PIC.
- * For these devices, this register is defined to be 4 bits wide.
- * Normally this is fine.  However for IO-APIC motherboards, or
- * non-x86 architectures (yes Via exists on PPC among other places),
- * we must mask the PCI_INTERRUPT_LINE value versus 0xf to get
- * interrupts delivered properly.
- */
-
 /*
  * FIXME: it is questionable that quirk_via_acpi
  * is needed.  It shows up as an ISA bridge, and does not
@@ -492,28 +481,30 @@ static void __devinit quirk_via_acpi(struct pci_dev *d)
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA,    PCI_DEVICE_ID_VIA_82C586_3,     quirk_via_acpi );
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA,    PCI_DEVICE_ID_VIA_82C686_4,     quirk_via_acpi );
 
-static void quirk_via_irqpic(struct pci_dev *dev)
+/*
+ * Via 686A/B:  The PCI_INTERRUPT_LINE register for the on-chip
+ * devices, USB0/1, AC97, MC97, and ACPI, has an unusual feature:
+ * when written, it makes an internal connection to the PIC.
+ * For these devices, this register is defined to be 4 bits wide.
+ * Normally this is fine.  However for IO-APIC motherboards, or
+ * non-x86 architectures (yes Via exists on PPC among other places),
+ * we must mask the PCI_INTERRUPT_LINE value versus 0xf to get
+ * interrupts delivered properly.
+ */
+static void quirk_via_irq(struct pci_dev *dev)
 {
        u8 irq, new_irq;
 
-#ifdef CONFIG_X86_IO_APIC
-       if (nr_ioapics && !skip_ioapic_setup)
-               return;
-#endif
-#ifdef CONFIG_ACPI
-       if (acpi_irq_model != ACPI_IRQ_MODEL_PIC)
-               return;
-#endif
        new_irq = dev->irq & 0xf;
        pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq);
        if (new_irq != irq) {
-               printk(KERN_INFO "PCI: Via PIC IRQ fixup for %s, from %d to %d\n",
+               printk(KERN_INFO "PCI: Via IRQ fixup for %s, from %d to %d\n",
                        pci_name(dev), irq, new_irq);
                udelay(15);     /* unknown if delay really needed */
                pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq);
        }
 }
-DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_irqpic);
+DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_irq);
 
 /*
  * PIIX3 USB: We have to disable USB interrupts that are