]> pilppa.com Git - linux-2.6-omap-h63xx.git/commitdiff
Blackfin SPI Driver: ensure cache coherency before doing DMA
authorVitja Makarov <vitja.makarov@gmail.com>
Tue, 7 Apr 2009 02:00:31 +0000 (19:00 -0700)
committerLinus Torvalds <torvalds@linux-foundation.org>
Tue, 7 Apr 2009 15:31:04 +0000 (08:31 -0700)
Flush or invalidate caches before doing DMA transfer, if needed.

[Mike Frysinger <vapier.adi@gmail.com>: add comment to address the
issue "Full duplex only works for non-DMA transfers".]
Signed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/spi/spi_bfin5xx.c

index 3410b0c55ed2a8562713c376bc38fbfc8b711e54..e440718b3209a023078528b7e0f3ca018854d8f9 100644 (file)
 #include <asm/portmux.h>
 #include <asm/bfin5xx_spi.h>
 
+/* reserved_mem_dcache_on and cache friends */
+#include <asm/cplbinit.h>
+#include <asm/cacheflush.h>
+
 #define DRV_NAME       "bfin-spi"
 #define DRV_AUTHOR     "Bryan Wu, Luke Yang"
 #define DRV_DESC       "Blackfin BF5xx on-chip SPI Controller Driver"
@@ -738,9 +742,10 @@ static void pump_transfers(unsigned long data)
                width, transfer->len);
 
        /*
-        * Try to map dma buffer and do a dma transfer if
-        * successful use different way to r/w according to
-        * drv_data->cur_chip->enable_dma
+        * Try to map dma buffer and do a dma transfer.  If successful use,
+        * different way to r/w according to the enable_dma settings and if
+        * we are not doing a full duplex transfer (since the hardware does
+        * not support full duplex DMA transfers).
         */
        if (!full_duplex && drv_data->cur_chip->enable_dma
                                && drv_data->len > 6) {
@@ -795,6 +800,12 @@ static void pump_transfers(unsigned long data)
                        /* set transfer mode, and enable SPI */
                        dev_dbg(&drv_data->pdev->dev, "doing DMA in.\n");
 
+                       /* invalidate caches, if needed */
+                       if (bfin_addr_dcachable((unsigned long) drv_data->rx))
+                               invalidate_dcache_range((unsigned long) drv_data->rx,
+                                                       (unsigned long) (drv_data->rx +
+                                                       drv_data->len));
+
                        /* clear tx reg soformer data is not shifted out */
                        write_TDBR(drv_data, 0xFFFF);
 
@@ -815,6 +826,12 @@ static void pump_transfers(unsigned long data)
                } else if (drv_data->tx != NULL) {
                        dev_dbg(&drv_data->pdev->dev, "doing DMA out.\n");
 
+                       /* flush caches, if needed */
+                       if (bfin_addr_dcachable((unsigned long) drv_data->tx))
+                               flush_dcache_range((unsigned long) drv_data->tx,
+                                               (unsigned long) (drv_data->tx +
+                                               drv_data->len));
+
                        /* start dma */
                        dma_enable_irq(drv_data->dma_channel);
                        dma_config = (RESTART | dma_width | DI_EN);