]> pilppa.com Git - linux-2.6-omap-h63xx.git/commitdiff
atlx: convert to net_device_ops
authorStephen Hemminger <shemminger@vyatta.com>
Thu, 20 Nov 2008 06:14:17 +0000 (22:14 -0800)
committerDavid S. Miller <davem@davemloft.net>
Thu, 20 Nov 2008 06:42:48 +0000 (22:42 -0800)
Convert this driver to network device ops. Compile tested only.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/atlx/atl1.c
drivers/net/atlx/atl2.c

index 611a86ebe16460a3ea8775dc1da319b13b14e966..7a0fb04e3480c6215eab391a208f4f2c4c93383f 100644 (file)
@@ -2880,6 +2880,21 @@ static void atl1_poll_controller(struct net_device *netdev)
 }
 #endif
 
+static const struct net_device_ops atl1_netdev_ops = {
+       .ndo_open               = atl1_open,
+       .ndo_stop               = atl1_close,
+       .ndo_set_multicast_list = atlx_set_multi,
+       .ndo_validate_addr      = eth_validate_addr,
+       .ndo_set_mac_address    = atl1_set_mac,
+       .ndo_change_mtu         = atl1_change_mtu,
+       .ndo_do_ioctl           = atlx_ioctl,
+       .ndo_tx_timeout = atlx_tx_timeout,
+       .ndo_vlan_rx_register   = atlx_vlan_rx_register,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+       .ndo_poll_controller    = atl1_poll_controller,
+#endif
+};
+
 /*
  * atl1_probe - Device Initialization Routine
  * @pdev: PCI device information struct
@@ -2967,20 +2982,9 @@ static int __devinit atl1_probe(struct pci_dev *pdev,
        adapter->mii.phy_id_mask = 0x1f;
        adapter->mii.reg_num_mask = 0x1f;
 
-       netdev->open = &atl1_open;
-       netdev->stop = &atl1_close;
+       netdev->netdev_ops = &atl1_netdev_ops;
        netdev->hard_start_xmit = &atl1_xmit_frame;
-
-       netdev->set_multicast_list = &atlx_set_multi;
-       netdev->set_mac_address = &atl1_set_mac;
-       netdev->change_mtu = &atl1_change_mtu;
-       netdev->do_ioctl = &atlx_ioctl;
-       netdev->tx_timeout = &atlx_tx_timeout;
        netdev->watchdog_timeo = 5 * HZ;
-#ifdef CONFIG_NET_POLL_CONTROLLER
-       netdev->poll_controller = atl1_poll_controller;
-#endif
-       netdev->vlan_rx_register = atlx_vlan_rx_register;
 
        netdev->ethtool_ops = &atl1_ethtool_ops;
        adapter->bd_number = cards_found;
index 60c9e5375eed406dd151ac38d7254616028feb88..688c21e81a8ef58753e5c1640bd1e8423bbfb36b 100644 (file)
@@ -1311,6 +1311,22 @@ static void atl2_poll_controller(struct net_device *netdev)
 }
 #endif
 
+
+static const struct net_device_ops atl2_netdev_ops = {
+       .ndo_open               = atl2_open,
+       .ndo_stop               = atl2_close,
+       .ndo_set_multicast_list = atl2_set_multi,
+       .ndo_validate_addr      = eth_validate_addr,
+       .ndo_set_mac_address    = atl2_set_mac,
+       .ndo_change_mtu         = atl2_change_mtu,
+       .ndo_do_ioctl           = atl2_ioctl,
+       .ndo_tx_timeout         = atl2_tx_timeout,
+       .ndo_vlan_rx_register   = atl2_vlan_rx_register,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+       .ndo_poll_controller    = atl2_poll_controller,
+#endif
+};
+
 /*
  * atl2_probe - Device Initialization Routine
  * @pdev: PCI device information struct
@@ -1384,25 +1400,10 @@ static int __devinit atl2_probe(struct pci_dev *pdev,
 
        atl2_setup_pcicmd(pdev);
 
-       netdev->open = &atl2_open;
-       netdev->stop = &atl2_close;
        netdev->hard_start_xmit = &atl2_xmit_frame;
-       netdev->set_multicast_list = &atl2_set_multi;
-       netdev->set_mac_address = &atl2_set_mac;
-       netdev->change_mtu = &atl2_change_mtu;
-       netdev->do_ioctl = &atl2_ioctl;
+       netdev->netdev_ops = &atl2_netdev_ops;
        atl2_set_ethtool_ops(netdev);
-
-#ifdef CONFIG_NET_POLL_CONTROLLER
-       netdev->poll_controller = atl2_poll_controller;
-#endif
-#ifdef HAVE_TX_TIMEOUT
-       netdev->tx_timeout = &atl2_tx_timeout;
        netdev->watchdog_timeo = 5 * HZ;
-#endif
-#ifdef NETIF_F_HW_VLAN_TX
-       netdev->vlan_rx_register = atl2_vlan_rx_register;
-#endif
        strncpy(netdev->name, pci_name(pdev), sizeof(netdev->name) - 1);
 
        netdev->mem_start = mmio_start;