--- /dev/null
+/*
+ * Windfarm PowerMac thermal control. iMac G5 iSight
+ *
+ * (c) Copyright 2007 Étienne Bersac <bersace@gmail.com>
+ *
+ * Bits & pieces from windfarm_pm81.c by (c) Copyright 2005 Benjamin
+ * Herrenschmidt, IBM Corp. <benh@kernel.crashing.org>
+ *
+ * Released under the term of the GNU GPL v2.
+ *
+ *
+ *
+ * PowerMac12,1
+ * ============
+ *
+ *
+ * The algorithm used is the PID control algorithm, used the same way
+ * the published Darwin code does, using the same values that are
+ * present in the Darwin 8.10 snapshot property lists (note however
+ * that none of the code has been re-used, it's a complete
+ * re-implementation
+ *
+ * There is two models using PowerMac12,1. Model 2 is iMac G5 iSight
+ * 17" while Model 3 is iMac G5 20". They do have both the same
+ * controls with a tiny difference. The control-ids of hard-drive-fan
+ * and cpu-fan is swapped.
+ *
+ *
+ * Target Correction :
+ *
+ * controls have a target correction calculated as :
+ *
+ * new_min = ((((average_power * slope) >> 16) + offset) >> 16) + min_value
+ * new_value = max(new_value, max(new_min, 0))
+ *
+ * OD Fan control correction.
+ *
+ * # model_id: 2
+ * offset : -19563152
+ * slope : 1956315
+ *
+ * # model_id: 3
+ * offset : -15650652
+ * slope : 1565065
+ *
+ * HD Fan control correction.
+ *
+ * # model_id: 2
+ * offset : -15650652
+ * slope : 1565065
+ *
+ * # model_id: 3
+ * offset : -19563152
+ * slope : 1956315
+ *
+ * CPU Fan control correction.
+ *
+ * # model_id: 2
+ * offset : -25431900
+ * slope : 2543190
+ *
+ * # model_id: 3
+ * offset : -15650652
+ * slope : 1565065
+ *
+ *
+ * Target rubber-banding :
+ *
+ * Some controls have a target correction which depends on another
+ * control value. The correction is computed in the following way :
+ *
+ * new_min = ref_value * slope + offset
+ *
+ * ref_value is the value of the reference control. If new_min is
+ * greater than 0, then we correct the target value using :
+ *
+ * new_target = max (new_target, new_min >> 16)
+ *
+ *
+ * # model_id : 2
+ * control : cpu-fan
+ * ref : optical-drive-fan
+ * offset : -15650652
+ * slope : 1565065
+ *
+ * # model_id : 3
+ * control : optical-drive-fan
+ * ref : hard-drive-fan
+ * offset : -32768000
+ * slope : 65536
+ *
+ *
+ * In order to have the moste efficient correction with those
+ * dependencies, we must trigger HD loop before OD loop before CPU
+ * loop.
+ *
+ *
+ * The various control loops found in Darwin config file are:
+ *
+ * HD Fan control loop.
+ *
+ * # model_id: 2
+ * control : hard-drive-fan
+ * sensor : hard-drive-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x002D70A3
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x370000
+ * Interval = 5s
+ *
+ * # model_id: 3
+ * control : hard-drive-fan
+ * sensor : hard-drive-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x002170A3
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x370000
+ * Interval = 5s
+ *
+ * OD Fan control loop.
+ *
+ * # model_id: 2
+ * control : optical-drive-fan
+ * sensor : optical-drive-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x001FAE14
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x320000
+ * Interval = 5s
+ *
+ * # model_id: 3
+ * control : optical-drive-fan
+ * sensor : optical-drive-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x001FAE14
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x320000
+ * Interval = 5s
+ *
+ * GPU Fan control loop.
+ *
+ * # model_id: 2
+ * control : hard-drive-fan
+ * sensor : gpu-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x002A6666
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x5A0000
+ * Interval = 5s
+ *
+ * # model_id: 3
+ * control : cpu-fan
+ * sensor : gpu-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x0010CCCC
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x500000
+ * Interval = 5s
+ *
+ * KODIAK (aka northbridge) Fan control loop.
+ *
+ * # model_id: 2
+ * control : optical-drive-fan
+ * sensor : north-bridge-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x003BD70A
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x550000
+ * Interval = 5s
+ *
+ * # model_id: 3
+ * control : hard-drive-fan
+ * sensor : north-bridge-temp
+ * PID params : G_d = 0x00000000
+ * G_p = 0x0030F5C2
+ * G_r = 0x00019999
+ * History = 2 entries
+ * Input target = 0x550000
+ * Interval = 5s
+ *
+ * CPU Fan control loop.
+ *
+ * control : cpu-fan
+ * sensors : cpu-temp, cpu-power
+ * PID params : from SDB partition
+ *
+ *
+ * CPU Slew control loop.
+ *
+ * control : cpufreq-clamp
+ * sensor : cpu-temp
+ *
+ */
+
+#undef DEBUG
+
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/init.h>
+#include <linux/spinlock.h>
+#include <linux/wait.h>
+#include <linux/kmod.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <asm/prom.h>
+#include <asm/machdep.h>
+#include <asm/io.h>
+#include <asm/system.h>
+#include <asm/sections.h>
+#include <asm/smu.h>
+
+#include "windfarm.h"
+#include "windfarm_pid.h"
+
+#define VERSION "0.3"
+
+static int pm121_mach_model; /* machine model id */
+
+/* Controls & sensors */
+static struct wf_sensor *sensor_cpu_power;
+static struct wf_sensor *sensor_cpu_temp;
+static struct wf_sensor *sensor_cpu_voltage;
+static struct wf_sensor *sensor_cpu_current;
+static struct wf_sensor *sensor_gpu_temp;
+static struct wf_sensor *sensor_north_bridge_temp;
+static struct wf_sensor *sensor_hard_drive_temp;
+static struct wf_sensor *sensor_optical_drive_temp;
+static struct wf_sensor *sensor_incoming_air_temp; /* unused ! */
+
+enum {
+ FAN_CPU,
+ FAN_HD,
+ FAN_OD,
+ CPUFREQ,
+ N_CONTROLS
+};
+static struct wf_control *controls[N_CONTROLS] = {};
+
+/* Set to kick the control loop into life */
+static int pm121_all_controls_ok, pm121_all_sensors_ok, pm121_started;
+
+enum {
+ FAILURE_FAN = 1 << 0,
+ FAILURE_SENSOR = 1 << 1,
+ FAILURE_OVERTEMP = 1 << 2
+};
+
+/* All sys loops. Note the HD before the OD loop in order to have it
+ run before. */
+enum {
+ LOOP_GPU, /* control = hd or cpu, but luckily,
+ it doesn't matter */
+ LOOP_HD, /* control = hd */
+ LOOP_KODIAK, /* control = hd or od */
+ LOOP_OD, /* control = od */
+ N_LOOPS
+};
+
+static const char *loop_names[N_LOOPS] = {
+ "GPU",
+ "HD",
+ "KODIAK",
+ "OD",
+};
+
+#define PM121_NUM_CONFIGS 2
+
+static unsigned int pm121_failure_state;
+static int pm121_readjust, pm121_skipping;
+static s32 average_power;
+
+struct pm121_correction {
+ int offset;
+ int slope;
+};
+
+static struct pm121_correction corrections[N_CONTROLS][PM121_NUM_CONFIGS] = {
+ /* FAN_OD */
+ {
+ /* MODEL 2 */
+ { .offset = -19563152,
+ .slope = 1956315
+ },
+ /* MODEL 3 */
+ { .offset = -15650652,
+ .slope = 1565065
+ },
+ },
+ /* FAN_HD */
+ {
+ /* MODEL 2 */
+ { .offset = -15650652,
+ .slope = 1565065
+ },
+ /* MODEL 3 */
+ { .offset = -19563152,
+ .slope = 1956315
+ },
+ },
+ /* FAN_CPU */
+ {
+ /* MODEL 2 */
+ { .offset = -25431900,
+ .slope = 2543190
+ },
+ /* MODEL 3 */
+ { .offset = -15650652,
+ .slope = 1565065
+ },
+ },
+ /* CPUFREQ has no correction (and is not implemented at all) */
+};
+
+struct pm121_connection {
+ unsigned int control_id;
+ unsigned int ref_id;
+ struct pm121_correction correction;
+};
+
+static struct pm121_connection pm121_connections[] = {
+ /* MODEL 2 */
+ { .control_id = FAN_CPU,
+ .ref_id = FAN_OD,
+ { .offset = -32768000,
+ .slope = 65536
+ }
+ },
+ /* MODEL 3 */
+ { .control_id = FAN_OD,
+ .ref_id = FAN_HD,
+ { .offset = -32768000,
+ .slope = 65536
+ }
+ },
+};
+
+/* pointer to the current model connection */
+static struct pm121_connection *pm121_connection;
+
+/*
+ * ****** System Fans Control Loop ******
+ *
+ */
+
+/* Since each loop handles only one control and we want to avoid
+ * writing virtual control, we store the control correction with the
+ * loop params. Some data are not set, there are common to all loop
+ * and thus, hardcoded.
+ */
+struct pm121_sys_param {
+ /* purely informative since we use mach_model-2 as index */
+ int model_id;
+ struct wf_sensor **sensor; /* use sensor_id instead ? */
+ s32 gp, itarget;
+ unsigned int control_id;
+};
+
+static struct pm121_sys_param
+pm121_sys_all_params[N_LOOPS][PM121_NUM_CONFIGS] = {
+ /* GPU Fan control loop */
+ {
+ { .model_id = 2,
+ .sensor = &sensor_gpu_temp,
+ .gp = 0x002A6666,
+ .itarget = 0x5A0000,
+ .control_id = FAN_HD,
+ },
+ { .model_id = 3,
+ .sensor = &sensor_gpu_temp,
+ .gp = 0x0010CCCC,
+ .itarget = 0x500000,
+ .control_id = FAN_CPU,
+ },
+ },
+ /* HD Fan control loop */
+ {
+ { .model_id = 2,
+ .sensor = &sensor_hard_drive_temp,
+ .gp = 0x002D70A3,
+ .itarget = 0x370000,
+ .control_id = FAN_HD,
+ },
+ { .model_id = 3,
+ .sensor = &sensor_hard_drive_temp,
+ .gp = 0x002170A3,
+ .itarget = 0x370000,
+ .control_id = FAN_HD,
+ },
+ },
+ /* KODIAK Fan control loop */
+ {
+ { .model_id = 2,
+ .sensor = &sensor_north_bridge_temp,
+ .gp = 0x003BD70A,
+ .itarget = 0x550000,
+ .control_id = FAN_OD,
+ },
+ { .model_id = 3,
+ .sensor = &sensor_north_bridge_temp,
+ .gp = 0x0030F5C2,
+ .itarget = 0x550000,
+ .control_id = FAN_HD,
+ },
+ },
+ /* OD Fan control loop */
+ {
+ { .model_id = 2,
+ .sensor = &sensor_optical_drive_temp,
+ .gp = 0x001FAE14,
+ .itarget = 0x320000,
+ .control_id = FAN_OD,
+ },
+ { .model_id = 3,
+ .sensor = &sensor_optical_drive_temp,
+ .gp = 0x001FAE14,
+ .itarget = 0x320000,
+ .control_id = FAN_OD,
+ },
+ },
+};
+
+/* the hardcoded values */
+#define PM121_SYS_GD 0x00000000
+#define PM121_SYS_GR 0x00019999
+#define PM121_SYS_HISTORY_SIZE 2
+#define PM121_SYS_INTERVAL 5
+
+/* State data used by the system fans control loop
+ */
+struct pm121_sys_state {
+ int ticks;
+ s32 setpoint;
+ struct wf_pid_state pid;
+};
+
+struct pm121_sys_state *pm121_sys_state[N_LOOPS] = {};
+
+/*
+ * ****** CPU Fans Control Loop ******
+ *
+ */
+
+#define PM121_CPU_INTERVAL 1
+
+/* State data used by the cpu fans control loop
+ */
+struct pm121_cpu_state {
+ int ticks;
+ s32 setpoint;
+ struct wf_cpu_pid_state pid;
+};
+
+static struct pm121_cpu_state *pm121_cpu_state;
+
+
+
+/*
+ * ***** Implementation *****
+ *
+ */
+
+/* correction the value using the output-low-bound correction algo */
+static s32 pm121_correct(s32 new_setpoint,
+ unsigned int control_id,
+ s32 min)
+{
+ s32 new_min;
+ struct pm121_correction *correction;
+ correction = &corrections[control_id][pm121_mach_model - 2];
+
+ new_min = (average_power * correction->slope) >> 16;
+ new_min += correction->offset;
+ new_min = (new_min >> 16) + min;
+
+ return max(new_setpoint, max(new_min, 0));
+}
+
+static s32 pm121_connect(unsigned int control_id, s32 setpoint)
+{
+ s32 new_min, value, new_setpoint;
+
+ if (pm121_connection->control_id == control_id) {
+ controls[control_id]->ops->get_value(controls[control_id],
+ &value);
+ new_min = value * pm121_connection->correction.slope;
+ new_min += pm121_connection->correction.offset;
+ if (new_min > 0) {
+ new_setpoint = max(setpoint, (new_min >> 16));
+ if (new_setpoint != setpoint) {
+ pr_debug("pm121: %s depending on %s, "
+ "corrected from %d to %d RPM\n",
+ controls[control_id]->name,
+ controls[pm121_connection->ref_id]->name,
+ (int) setpoint, (int) new_setpoint);
+ }
+ } else
+ new_setpoint = setpoint;
+ }
+ /* no connection */
+ else
+ new_setpoint = setpoint;
+
+ return new_setpoint;
+}
+
+/* FAN LOOPS */
+static void pm121_create_sys_fans(int loop_id)
+{
+ struct pm121_sys_param *param = NULL;
+ struct wf_pid_param pid_param;
+ struct wf_control *control = NULL;
+ int i;
+
+ /* First, locate the params for this model */
+ for (i = 0; i < PM121_NUM_CONFIGS; i++) {
+ if (pm121_sys_all_params[loop_id][i].model_id == pm121_mach_model) {
+ param = &(pm121_sys_all_params[loop_id][i]);
+ break;
+ }
+ }
+
+ /* No params found, put fans to max */
+ if (param == NULL) {
+ printk(KERN_WARNING "pm121: %s fan config not found "
+ " for this machine model\n",
+ loop_names[loop_id]);
+ goto fail;
+ }
+
+ control = controls[param->control_id];
+
+ /* Alloc & initialize state */
+ pm121_sys_state[loop_id] = kmalloc(sizeof(struct pm121_sys_state),
+ GFP_KERNEL);
+ if (pm121_sys_state[loop_id] == NULL) {
+ printk(KERN_WARNING "pm121: Memory allocation error\n");
+ goto fail;
+ }
+ pm121_sys_state[loop_id]->ticks = 1;
+
+ /* Fill PID params */
+ pid_param.gd = PM121_SYS_GD;
+ pid_param.gp = param->gp;
+ pid_param.gr = PM121_SYS_GR;
+ pid_param.interval = PM121_SYS_INTERVAL;
+ pid_param.history_len = PM121_SYS_HISTORY_SIZE;
+ pid_param.itarget = param->itarget;
+ pid_param.min = control->ops->get_min(control);
+ pid_param.max = control->ops->get_max(control);
+
+ wf_pid_init(&pm121_sys_state[loop_id]->pid, &pid_param);
+
+ pr_debug("pm121: %s Fan control loop initialized.\n"
+ " itarged=%d.%03d, min=%d RPM, max=%d RPM\n",
+ loop_names[loop_id], FIX32TOPRINT(pid_param.itarget),
+ pid_param.min, pid_param.max);
+ return;
+
+ fail:
+ /* note that this is not optimal since another loop may still
+ control the same control */
+ printk(KERN_WARNING "pm121: failed to set up %s loop "
+ "setting \"%s\" to max speed.\n",
+ loop_names[loop_id], control->name);
+
+ if (control)
+ wf_control_set_max(control);
+}
+
+static void pm121_sys_fans_tick(int loop_id)
+{
+ struct pm121_sys_param *param;
+ struct pm121_sys_state *st;
+ struct wf_sensor *sensor;
+ struct wf_control *control;
+ s32 temp, new_setpoint;
+ int rc;
+
+ param = &(pm121_sys_all_params[loop_id][pm121_mach_model-2]);
+ st = pm121_sys_state[loop_id];
+ sensor = *(param->sensor);
+ control = controls[param->control_id];
+
+ if (--st->ticks != 0) {
+ if (pm121_readjust)
+ goto readjust;
+ return;
+ }
+ st->ticks = PM121_SYS_INTERVAL;
+
+ rc = sensor->ops->get_value(sensor, &temp);
+ if (rc) {
+ printk(KERN_WARNING "windfarm: %s sensor error %d\n",
+ sensor->name, rc);
+ pm121_failure_state |= FAILURE_SENSOR;
+ return;
+ }
+
+ pr_debug("pm121: %s Fan tick ! %s: %d.%03d\n",
+ loop_names[loop_id], sensor->name,
+ FIX32TOPRINT(temp));
+
+ new_setpoint = wf_pid_run(&st->pid, temp);
+
+ /* correction */
+ new_setpoint = pm121_correct(new_setpoint,
+ param->control_id,
+ st->pid.param.min);
+ /* linked corretion */
+ new_setpoint = pm121_connect(param->control_id, new_setpoint);
+
+ if (new_setpoint == st->setpoint)
+ return;
+ st->setpoint = new_setpoint;
+ pr_debug("pm121: %s corrected setpoint: %d RPM\n",
+ control->name, (int)new_setpoint);
+ readjust:
+ if (control && pm121_failure_state == 0) {
+ rc = control->ops->set_value(control, st->setpoint);
+ if (rc) {
+ printk(KERN_WARNING "windfarm: %s fan error %d\n",
+ control->name, rc);
+ pm121_failure_state |= FAILURE_FAN;
+ }
+ }
+}
+
+
+/* CPU LOOP */
+static void pm121_create_cpu_fans(void)
+{
+ struct wf_cpu_pid_param pid_param;
+ const struct smu_sdbp_header *hdr;
+ struct smu_sdbp_cpupiddata *piddata;
+ struct smu_sdbp_fvt *fvt;
+ struct wf_control *fan_cpu;
+ s32 tmax, tdelta, maxpow, powadj;
+
+ fan_cpu = controls[FAN_CPU];
+
+ /* First, locate the PID params in SMU SBD */
+ hdr = smu_get_sdb_partition(SMU_SDB_CPUPIDDATA_ID, NULL);
+ if (hdr == 0) {
+ printk(KERN_WARNING "pm121: CPU PID fan config not found.\n");
+ goto fail;
+ }
+ piddata = (struct smu_sdbp_cpupiddata *)&hdr[1];
+
+ /* Get the FVT params for operating point 0 (the only supported one
+ * for now) in order to get tmax
+ */
+ hdr = smu_get_sdb_partition(SMU_SDB_FVT_ID, NULL);
+ if (hdr) {
+ fvt = (struct smu_sdbp_fvt *)&hdr[1];
+ tmax = ((s32)fvt->maxtemp) << 16;
+ } else
+ tmax = 0x5e0000; /* 94 degree default */
+
+ /* Alloc & initialize state */
+ pm121_cpu_state = kmalloc(sizeof(struct pm121_cpu_state),
+ GFP_KERNEL);
+ if (pm121_cpu_state == NULL)
+ goto fail;
+ pm121_cpu_state->ticks = 1;
+
+ /* Fill PID params */
+ pid_param.interval = PM121_CPU_INTERVAL;
+ pid_param.history_len = piddata->history_len;
+ if (pid_param.history_len > WF_CPU_PID_MAX_HISTORY) {
+ printk(KERN_WARNING "pm121: History size overflow on "
+ "CPU control loop (%d)\n", piddata->history_len);
+ pid_param.history_len = WF_CPU_PID_MAX_HISTORY;
+ }
+ pid_param.gd = piddata->gd;
+ pid_param.gp = piddata->gp;
+ pid_param.gr = piddata->gr / pid_param.history_len;
+
+ tdelta = ((s32)piddata->target_temp_delta) << 16;
+ maxpow = ((s32)piddata->max_power) << 16;
+ powadj = ((s32)piddata->power_adj) << 16;
+
+ pid_param.tmax = tmax;
+ pid_param.ttarget = tmax - tdelta;
+ pid_param.pmaxadj = maxpow - powadj;
+
+ pid_param.min = fan_cpu->ops->get_min(fan_cpu);
+ pid_param.max = fan_cpu->ops->get_max(fan_cpu);
+
+ wf_cpu_pid_init(&pm121_cpu_state->pid, &pid_param);
+
+ pr_debug("pm121: CPU Fan control initialized.\n");
+ pr_debug(" ttarged=%d.%03d, tmax=%d.%03d, min=%d RPM, max=%d RPM,\n",
+ FIX32TOPRINT(pid_param.ttarget), FIX32TOPRINT(pid_param.tmax),
+ pid_param.min, pid_param.max);
+
+ return;
+
+ fail:
+ printk(KERN_WARNING "pm121: CPU fan config not found, max fan speed\n");
+
+ if (controls[CPUFREQ])
+ wf_control_set_max(controls[CPUFREQ]);
+ if (fan_cpu)
+ wf_control_set_max(fan_cpu);
+}
+
+
+static void pm121_cpu_fans_tick(struct pm121_cpu_state *st)
+{
+ s32 new_setpoint, temp, power;
+ struct wf_control *fan_cpu = NULL;
+ int rc;
+
+ if (--st->ticks != 0) {
+ if (pm121_readjust)
+ goto readjust;
+ return;
+ }
+ st->ticks = PM121_CPU_INTERVAL;
+
+ fan_cpu = controls[FAN_CPU];
+
+ rc = sensor_cpu_temp->ops->get_value(sensor_cpu_temp, &temp);
+ if (rc) {
+ printk(KERN_WARNING "pm121: CPU temp sensor error %d\n",
+ rc);
+ pm121_failure_state |= FAILURE_SENSOR;
+ return;
+ }
+
+ rc = sensor_cpu_power->ops->get_value(sensor_cpu_power, &power);
+ if (rc) {
+ printk(KERN_WARNING "pm121: CPU power sensor error %d\n",
+ rc);
+ pm121_failure_state |= FAILURE_SENSOR;
+ return;
+ }
+
+ pr_debug("pm121: CPU Fans tick ! CPU temp: %d.%03d°C, power: %d.%03d\n",
+ FIX32TOPRINT(temp), FIX32TOPRINT(power));
+
+ if (temp > st->pid.param.tmax)
+ pm121_failure_state |= FAILURE_OVERTEMP;
+
+ new_setpoint = wf_cpu_pid_run(&st->pid, power, temp);
+
+ /* correction */
+ new_setpoint = pm121_correct(new_setpoint,
+ FAN_CPU,
+ st->pid.param.min);
+
+ /* connected correction */
+ new_setpoint = pm121_connect(FAN_CPU, new_setpoint);
+
+ if (st->setpoint == new_setpoint)
+ return;
+ st->setpoint = new_setpoint;
+ pr_debug("pm121: CPU corrected setpoint: %d RPM\n", (int)new_setpoint);
+
+ readjust:
+ if (fan_cpu && pm121_failure_state == 0) {
+ rc = fan_cpu->ops->set_value(fan_cpu, st->setpoint);
+ if (rc) {
+ printk(KERN_WARNING "pm121: %s fan error %d\n",
+ fan_cpu->name, rc);
+ pm121_failure_state |= FAILURE_FAN;
+ }
+ }
+}
+
+/*
+ * ****** Common ******
+ *
+ */
+
+static void pm121_tick(void)
+{
+ unsigned int last_failure = pm121_failure_state;
+ unsigned int new_failure;
+ s32 total_power;
+ int i;
+
+ if (!pm121_started) {
+ pr_debug("pm121: creating control loops !\n");
+ for (i = 0; i < N_LOOPS; i++)
+ pm121_create_sys_fans(i);
+
+ pm121_create_cpu_fans();
+ pm121_started = 1;
+ }
+
+ /* skipping ticks */
+ if (pm121_skipping && --pm121_skipping)
+ return;
+
+ /* compute average power */
+ total_power = 0;
+ for (i = 0; i < pm121_cpu_state->pid.param.history_len; i++)
+ total_power += pm121_cpu_state->pid.powers[i];
+
+ average_power = total_power / pm121_cpu_state->pid.param.history_len;
+
+
+ pm121_failure_state = 0;
+ for (i = 0 ; i < N_LOOPS; i++) {
+ if (pm121_sys_state[i])
+ pm121_sys_fans_tick(i);
+ }
+
+ if (pm121_cpu_state)
+ pm121_cpu_fans_tick(pm121_cpu_state);
+
+ pm121_readjust = 0;
+ new_failure = pm121_failure_state & ~last_failure;
+
+ /* If entering failure mode, clamp cpufreq and ramp all
+ * fans to full speed.
+ */
+ if (pm121_failure_state && !last_failure) {
+ for (i = 0; i < N_CONTROLS; i++) {
+ if (controls[i])
+ wf_control_set_max(controls[i]);
+ }
+ }
+
+ /* If leaving failure mode, unclamp cpufreq and readjust
+ * all fans on next iteration
+ */
+ if (!pm121_failure_state && last_failure) {
+ if (controls[CPUFREQ])
+ wf_control_set_min(controls[CPUFREQ]);
+ pm121_readjust = 1;
+ }
+
+ /* Overtemp condition detected, notify and start skipping a couple
+ * ticks to let the temperature go down
+ */
+ if (new_failure & FAILURE_OVERTEMP) {
+ wf_set_overtemp();
+ pm121_skipping = 2;
+ }
+
+ /* We only clear the overtemp condition if overtemp is cleared
+ * _and_ no other failure is present. Since a sensor error will
+ * clear the overtemp condition (can't measure temperature) at
+ * the control loop levels, but we don't want to keep it clear
+ * here in this case
+ */
+ if (new_failure == 0 && last_failure & FAILURE_OVERTEMP)
+ wf_clear_overtemp();
+}
+
+
+static struct wf_control* pm121_register_control(struct wf_control *ct,
+ const char *match,
+ unsigned int id)
+{
+ if (controls[id] == NULL && !strcmp(ct->name, match)) {
+ if (wf_get_control(ct) == 0)
+ controls[id] = ct;
+ }
+ return controls[id];
+}
+
+static void pm121_new_control(struct wf_control *ct)
+{
+ int all = 1;
+
+ if (pm121_all_controls_ok)
+ return;
+
+ all = pm121_register_control(ct, "optical-drive-fan", FAN_OD) && all;
+ all = pm121_register_control(ct, "hard-drive-fan", FAN_HD) && all;
+ all = pm121_register_control(ct, "cpu-fan", FAN_CPU) && all;
+ all = pm121_register_control(ct, "cpufreq-clamp", CPUFREQ) && all;
+
+ if (all)
+ pm121_all_controls_ok = 1;
+}
+
+
+
+
+static struct wf_sensor* pm121_register_sensor(struct wf_sensor *sensor,
+ const char *match,
+ struct wf_sensor **var)
+{
+ if (*var == NULL && !strcmp(sensor->name, match)) {
+ if (wf_get_sensor(sensor) == 0)
+ *var = sensor;
+ }
+ return *var;
+}
+
+static void pm121_new_sensor(struct wf_sensor *sr)
+{
+ int all = 1;
+
+ if (pm121_all_sensors_ok)
+ return;
+
+ all = pm121_register_sensor(sr, "cpu-temp",
+ &sensor_cpu_temp) && all;
+ all = pm121_register_sensor(sr, "cpu-current",
+ &sensor_cpu_current) && all;
+ all = pm121_register_sensor(sr, "cpu-voltage",
+ &sensor_cpu_voltage) && all;
+ all = pm121_register_sensor(sr, "cpu-power",
+ &sensor_cpu_power) && all;
+ all = pm121_register_sensor(sr, "hard-drive-temp",
+ &sensor_hard_drive_temp) && all;
+ all = pm121_register_sensor(sr, "optical-drive-temp",
+ &sensor_optical_drive_temp) && all;
+ all = pm121_register_sensor(sr, "incoming-air-temp",
+ &sensor_incoming_air_temp) && all;
+ all = pm121_register_sensor(sr, "north-bridge-temp",
+ &sensor_north_bridge_temp) && all;
+ all = pm121_register_sensor(sr, "gpu-temp",
+ &sensor_gpu_temp) && all;
+
+ if (all)
+ pm121_all_sensors_ok = 1;
+}
+
+
+
+static int pm121_notify(struct notifier_block *self,
+ unsigned long event, void *data)
+{
+ switch (event) {
+ case WF_EVENT_NEW_CONTROL:
+ pr_debug("pm121: new control %s detected\n",
+ ((struct wf_control *)data)->name);
+ pm121_new_control(data);
+ break;
+ case WF_EVENT_NEW_SENSOR:
+ pr_debug("pm121: new sensor %s detected\n",
+ ((struct wf_sensor *)data)->name);
+ pm121_new_sensor(data);
+ break;
+ case WF_EVENT_TICK:
+ if (pm121_all_controls_ok && pm121_all_sensors_ok)
+ pm121_tick();
+ break;
+ }
+
+ return 0;
+}
+
+static struct notifier_block pm121_events = {
+ .notifier_call = pm121_notify,
+};
+
+static int pm121_init_pm(void)
+{
+ const struct smu_sdbp_header *hdr;
+
+ hdr = smu_get_sdb_partition(SMU_SDB_SENSORTREE_ID, NULL);
+ if (hdr != 0) {
+ struct smu_sdbp_sensortree *st =
+ (struct smu_sdbp_sensortree *)&hdr[1];
+ pm121_mach_model = st->model_id;
+ }
+
+ pm121_connection = &pm121_connections[pm121_mach_model - 2];
+
+ printk(KERN_INFO "pm121: Initializing for iMac G5 iSight model ID %d\n",
+ pm121_mach_model);
+
+ return 0;
+}
+
+
+static int pm121_probe(struct platform_device *ddev)
+{
+ wf_register_client(&pm121_events);
+
+ return 0;
+}
+
+static int __devexit pm121_remove(struct platform_device *ddev)
+{
+ wf_unregister_client(&pm121_events);
+ return 0;
+}
+
+static struct platform_driver pm121_driver = {
+ .probe = pm121_probe,
+ .remove = __devexit_p(pm121_remove),
+ .driver = {
+ .name = "windfarm",
+ .bus = &platform_bus_type,
+ },
+};
+
+
+static int __init pm121_init(void)
+{
+ int rc = -ENODEV;
+
+ if (machine_is_compatible("PowerMac12,1"))
+ rc = pm121_init_pm();
+
+ if (rc == 0) {
+ request_module("windfarm_smu_controls");
+ request_module("windfarm_smu_sensors");
+ request_module("windfarm_smu_sat");
+ request_module("windfarm_lm75_sensor");
+ request_module("windfarm_max6690_sensor");
+ request_module("windfarm_cpufreq_clamp");
+ platform_driver_register(&pm121_driver);
+ }
+
+ return rc;
+}
+
+static void __exit pm121_exit(void)
+{
+
+ platform_driver_unregister(&pm121_driver);
+}
+
+
+module_init(pm121_init);
+module_exit(pm121_exit);
+
+MODULE_AUTHOR("Étienne Bersac <bersace@gmail.com>");
+MODULE_DESCRIPTION("Thermal control logic for iMac G5 (iSight)");
+MODULE_LICENSE("GPL");
+
projects / linux-2.6-omap-h63xx.git / commitdiff