m68k/Atari: remove the dead ATARI_SCC{,_DMA} options

It seems the driver was removed back in kernel 2.3 but the options were
forgotten.

Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

diff --git a/arch/m68k/Kconfig b/arch/m68k/Kconfig
index 8012ff7d75134766f098a4a84050dca94f6c25b4..8c5e1de68fcb6737bbfb1995b21736ac379fa7cc 100644 (file)
--- a/arch/m68k/Kconfig
+++ b/arch/m68k/Kconfig
@@ -490,28 +490,6 @@ config ATARI_MFPSER
          Note for Falcon users: You also have an MFP port, it's just not
          wired to the outside... But you could use the port under Linux.
 
-config ATARI_SCC
-       tristate "Atari SCC serial support"
-       depends on ATARI
-       ---help---
-         If you have serial ports based on a Zilog SCC chip (Modem2, Serial2,
-         LAN) and like to use them under Linux, say Y. All built-in SCC's are
-         supported (TT, MegaSTE, Falcon), and also the ST-ESCC. If you have
-         two connectors for channel A (Serial2 and LAN), they are visible as
-         two separate devices.
-
-         To compile this driver as a module, choose M here.
-
-config ATARI_SCC_DMA
-       bool "Atari SCC serial DMA support"
-       depends on ATARI_SCC
-       help
-         This enables DMA support for receiving data on channel A of the SCC.
-         If you have a TT you may say Y here and read
-         drivers/char/atari_SCC.README. All other users should say N here,
-         because only the TT has SCC-DMA, even if your machine keeps claiming
-         so at boot time.
-
 config ATARI_MIDI
        tristate "Atari MIDI serial support"
        depends on ATARI
@@ -628,7 +606,7 @@ config DN_SERIAL
 
 config SERIAL_CONSOLE
        bool "Support for serial port console"
-       depends on (AMIGA || ATARI || MAC || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_SCC=y || ATARI_MIDI=y || MAC_SCC=y || AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL)
+       depends on (AMIGA || ATARI || MAC || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_MIDI=y || MAC_SCC=y || AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL)
        ---help---
          If you say Y here, it will be possible to use a serial port as the
          system console (the system console is the device which receives all