]> pilppa.com Git - linux-2.6-omap-h63xx.git/commitdiff
drm/i915: Manage PIPESTAT to control vblank interrupts instead of IMR.
authorKeith Packard <keithp@keithp.com>
Tue, 4 Nov 2008 10:03:27 +0000 (02:03 -0800)
committerDave Airlie <airlied@redhat.com>
Mon, 24 Nov 2008 23:27:24 +0000 (09:27 +1000)
The pipestat fields affect reporting of all vblank-related interrupts, so we
have to reset them during the irq_handler, and while enabling vblank
interrupts.  Otherwise, if a pipe status field had been set to non-zero
before enabling reporting, we would never see an interrupt again.

This patch adds i915_enable_pipestat and i915_disable_pipestat to abstract
out the steps needed to change the reported interrupts.

Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_irq.c
drivers/gpu/drm/i915/i915_opregion.c

index ef1c0b8f8d07858422526f10e6f4fb63e428cf3d..ed1edcf8704fdf021720c0ecc8f6c2e073f6df1a 100644 (file)
@@ -132,6 +132,7 @@ typedef struct drm_i915_private {
        int user_irq_refcount;
        /** Cached value of IMR to avoid reads in updating the bitfield */
        u32 irq_mask_reg;
+       u32 pipestat[2];
 
        int tex_lru_log_granularity;
        int allow_batchbuffer;
@@ -446,6 +447,13 @@ extern int i915_vblank_swap(struct drm_device *dev, void *data,
                            struct drm_file *file_priv);
 extern void i915_enable_irq(drm_i915_private_t *dev_priv, u32 mask);
 
+void
+i915_enable_pipestat(drm_i915_private_t *dev_priv, int pipe, u32 mask);
+
+void
+i915_disable_pipestat(drm_i915_private_t *dev_priv, int pipe, u32 mask);
+
+
 /* i915_mem.c */
 extern int i915_mem_alloc(struct drm_device *dev, void *data,
                          struct drm_file *file_priv);
index 82752d6177a4949d406ec383b53cc31e6bcf9474..ca3ed1833908be093ff87c8606065e4f692c27b7 100644 (file)
 
 #define MAX_NOPID ((u32)~0)
 
-/** These are the interrupts used by the driver */
-#define I915_INTERRUPT_ENABLE_MASK (I915_USER_INTERRUPT |              \
-                                   I915_ASLE_INTERRUPT |               \
-                                   I915_DISPLAY_PIPE_A_EVENT_INTERRUPT | \
-                                   I915_DISPLAY_PIPE_B_EVENT_INTERRUPT)
+/**
+ * Interrupts that are always left unmasked.
+ *
+ * Since pipe events are edge-triggered from the PIPESTAT register to IIR,
+ * we leave them always unmasked in IMR and then control enabling them through
+ * PIPESTAT alone.
+ */
+#define I915_INTERRUPT_ENABLE_FIX (I915_ASLE_INTERRUPT | \
+                                  I915_DISPLAY_PIPE_A_EVENT_INTERRUPT |  \
+                                  I915_DISPLAY_PIPE_B_EVENT_INTERRUPT)
+
+/** Interrupts that we mask and unmask at runtime. */
+#define I915_INTERRUPT_ENABLE_VAR (I915_USER_INTERRUPT)
+
+/** These are all of the interrupts used by the driver */
+#define I915_INTERRUPT_ENABLE_MASK (I915_INTERRUPT_ENABLE_FIX | \
+                                   I915_INTERRUPT_ENABLE_VAR)
 
 void
 i915_enable_irq(drm_i915_private_t *dev_priv, u32 mask)
@@ -59,6 +71,41 @@ i915_disable_irq(drm_i915_private_t *dev_priv, u32 mask)
        }
 }
 
+static inline u32
+i915_pipestat(int pipe)
+{
+       if (pipe == 0)
+               return PIPEASTAT;
+       if (pipe == 1)
+               return PIPEBSTAT;
+       BUG_ON(1);
+}
+
+void
+i915_enable_pipestat(drm_i915_private_t *dev_priv, int pipe, u32 mask)
+{
+       if ((dev_priv->pipestat[pipe] & mask) != mask) {
+               u32 reg = i915_pipestat(pipe);
+
+               dev_priv->pipestat[pipe] |= mask;
+               /* Enable the interrupt, clear any pending status */
+               I915_WRITE(reg, dev_priv->pipestat[pipe] | (mask >> 16));
+               (void) I915_READ(reg);
+       }
+}
+
+void
+i915_disable_pipestat(drm_i915_private_t *dev_priv, int pipe, u32 mask)
+{
+       if ((dev_priv->pipestat[pipe] & mask) != 0) {
+               u32 reg = i915_pipestat(pipe);
+
+               dev_priv->pipestat[pipe] &= ~mask;
+               I915_WRITE(reg, dev_priv->pipestat[pipe]);
+               (void) I915_READ(reg);
+       }
+}
+
 /**
  * i915_pipe_enabled - check if a pipe is enabled
  * @dev: DRM device
@@ -122,9 +169,11 @@ irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS)
        struct drm_device *dev = (struct drm_device *) arg;
        drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
        u32 iir;
-       u32 pipea_stats, pipeb_stats;
+       u32 pipea_stats = 0, pipeb_stats = 0;
        int vblank = 0;
+       unsigned long irqflags;
 
+       spin_lock_irqsave(&dev_priv->user_irq_lock, irqflags);
        atomic_inc(&dev_priv->irq_received);
 
        if (dev->pdev->msi_enabled)
@@ -136,44 +185,20 @@ irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS)
                        I915_WRITE(IMR, dev_priv->irq_mask_reg);
                        (void) I915_READ(IMR);
                }
+               spin_unlock_irqrestore(&dev_priv->user_irq_lock, irqflags);
                return IRQ_NONE;
        }
 
        /*
-        * Clear the PIPE(A|B)STAT regs before the IIR otherwise
-        * we may get extra interrupts.
+        * Clear the PIPE(A|B)STAT regs before the IIR
         */
        if (iir & I915_DISPLAY_PIPE_A_EVENT_INTERRUPT) {
                pipea_stats = I915_READ(PIPEASTAT);
-               if (!(dev_priv->vblank_pipe & DRM_I915_VBLANK_PIPE_A))
-                       pipea_stats &= ~(PIPE_START_VBLANK_INTERRUPT_ENABLE |
-                                        PIPE_VBLANK_INTERRUPT_ENABLE);
-               else if (pipea_stats & (PIPE_START_VBLANK_INTERRUPT_STATUS|
-                                       PIPE_VBLANK_INTERRUPT_STATUS)) {
-                       vblank++;
-                       drm_handle_vblank(dev, 0);
-               }
-
                I915_WRITE(PIPEASTAT, pipea_stats);
        }
+
        if (iir & I915_DISPLAY_PIPE_B_EVENT_INTERRUPT) {
                pipeb_stats = I915_READ(PIPEBSTAT);
-               /* Ack the event */
-               I915_WRITE(PIPEBSTAT, pipeb_stats);
-
-               /* The vblank interrupt gets enabled even if we didn't ask for
-                  it, so make sure it's shut down again */
-               if (!(dev_priv->vblank_pipe & DRM_I915_VBLANK_PIPE_B))
-                       pipeb_stats &= ~(PIPE_START_VBLANK_INTERRUPT_ENABLE |
-                                        PIPE_VBLANK_INTERRUPT_ENABLE);
-               else if (pipeb_stats & (PIPE_START_VBLANK_INTERRUPT_STATUS|
-                                       PIPE_VBLANK_INTERRUPT_STATUS)) {
-                       vblank++;
-                       drm_handle_vblank(dev, 1);
-               }
-
-               if (pipeb_stats & I915_LEGACY_BLC_EVENT_STATUS)
-                       opregion_asle_intr(dev);
                I915_WRITE(PIPEBSTAT, pipeb_stats);
        }
 
@@ -182,6 +207,8 @@ irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS)
                I915_WRITE(IMR, dev_priv->irq_mask_reg);
        (void) I915_READ(IIR); /* Flush posted writes */
 
+       spin_unlock_irqrestore(&dev_priv->user_irq_lock, irqflags);
+
        if (dev_priv->sarea_priv)
                dev_priv->sarea_priv->last_dispatch =
                        READ_BREADCRUMB(dev_priv);
@@ -191,7 +218,18 @@ irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS)
                DRM_WAKEUP(&dev_priv->irq_queue);
        }
 
-       if (iir & I915_ASLE_INTERRUPT)
+       if (pipea_stats & I915_VBLANK_INTERRUPT_STATUS) {
+               vblank++;
+               drm_handle_vblank(dev, 0);
+       }
+
+       if (pipeb_stats & I915_VBLANK_INTERRUPT_STATUS) {
+               vblank++;
+               drm_handle_vblank(dev, 1);
+       }
+
+       if ((pipeb_stats & I915_LEGACY_BLC_EVENT_STATUS) ||
+           (iir & I915_ASLE_INTERRUPT))
                opregion_asle_intr(dev);
 
        return IRQ_HANDLED;
@@ -330,48 +368,16 @@ int i915_irq_wait(struct drm_device *dev, void *data,
 int i915_enable_vblank(struct drm_device *dev, int pipe)
 {
        drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
-       u32     pipestat_reg = 0;
-       u32     pipestat;
-       u32     interrupt = 0;
        unsigned long irqflags;
 
-       switch (pipe) {
-       case 0:
-               pipestat_reg = PIPEASTAT;
-               interrupt = I915_DISPLAY_PIPE_A_EVENT_INTERRUPT;
-               break;
-       case 1:
-               pipestat_reg = PIPEBSTAT;
-               interrupt = I915_DISPLAY_PIPE_B_EVENT_INTERRUPT;
-               break;
-       default:
-               DRM_ERROR("tried to enable vblank on non-existent pipe %d\n",
-                         pipe);
-               return 0;
-       }
-
        spin_lock_irqsave(&dev_priv->user_irq_lock, irqflags);
-       /* Enabling vblank events in IMR comes before PIPESTAT write, or
-        * there's a race where the PIPESTAT vblank bit gets set to 1, so
-        * the OR of enabled PIPESTAT bits goes to 1, so the PIPExEVENT in
-        * ISR flashes to 1, but the IIR bit doesn't get set to 1 because
-        * IMR masks it.  It doesn't ever get set after we clear the masking
-        * in IMR because the ISR bit is edge, not level-triggered, on the
-        * OR of PIPESTAT bits.
-        */
-       i915_enable_irq(dev_priv, interrupt);
-       pipestat = I915_READ(pipestat_reg);
        if (IS_I965G(dev))
-               pipestat |= PIPE_START_VBLANK_INTERRUPT_ENABLE;
+               i915_enable_pipestat(dev_priv, pipe,
+                                    PIPE_START_VBLANK_INTERRUPT_ENABLE);
        else
-               pipestat |= PIPE_VBLANK_INTERRUPT_ENABLE;
-       /* Clear any stale interrupt status */
-       pipestat |= (PIPE_START_VBLANK_INTERRUPT_STATUS |
-                    PIPE_VBLANK_INTERRUPT_STATUS);
-       I915_WRITE(pipestat_reg, pipestat);
-       (void) I915_READ(pipestat_reg); /* Posting read */
+               i915_enable_pipestat(dev_priv, pipe,
+                                    PIPE_VBLANK_INTERRUPT_ENABLE);
        spin_unlock_irqrestore(&dev_priv->user_irq_lock, irqflags);
-
        return 0;
 }
 
@@ -381,37 +387,12 @@ int i915_enable_vblank(struct drm_device *dev, int pipe)
 void i915_disable_vblank(struct drm_device *dev, int pipe)
 {
        drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
-       u32     pipestat_reg = 0;
-       u32     pipestat;
-       u32     interrupt = 0;
        unsigned long irqflags;
 
-       switch (pipe) {
-       case 0:
-               pipestat_reg = PIPEASTAT;
-               interrupt = I915_DISPLAY_PIPE_A_EVENT_INTERRUPT;
-               break;
-       case 1:
-               pipestat_reg = PIPEBSTAT;
-               interrupt = I915_DISPLAY_PIPE_B_EVENT_INTERRUPT;
-               break;
-       default:
-               DRM_ERROR("tried to disable vblank on non-existent pipe %d\n",
-                         pipe);
-               return;
-               break;
-       }
-
        spin_lock_irqsave(&dev_priv->user_irq_lock, irqflags);
-       i915_disable_irq(dev_priv, interrupt);
-       pipestat = I915_READ(pipestat_reg);
-       pipestat &= ~(PIPE_START_VBLANK_INTERRUPT_ENABLE |
-                     PIPE_VBLANK_INTERRUPT_ENABLE);
-       /* Clear any stale interrupt status */
-       pipestat |= (PIPE_START_VBLANK_INTERRUPT_STATUS |
-                    PIPE_VBLANK_INTERRUPT_STATUS);
-       I915_WRITE(pipestat_reg, pipestat);
-       (void) I915_READ(pipestat_reg); /* Posting read */
+       i915_disable_pipestat(dev_priv, pipe,
+                             PIPE_VBLANK_INTERRUPT_ENABLE |
+                             PIPE_START_VBLANK_INTERRUPT_ENABLE);
        spin_unlock_irqrestore(&dev_priv->user_irq_lock, irqflags);
 }
 
@@ -476,8 +457,11 @@ void i915_driver_irq_preinstall(struct drm_device * dev)
        drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
 
        I915_WRITE(HWSTAM, 0xeffe);
+       I915_WRITE(PIPEASTAT, 0);
+       I915_WRITE(PIPEBSTAT, 0);
        I915_WRITE(IMR, 0xffffffff);
        I915_WRITE(IER, 0x0);
+       (void) I915_READ(IER);
 }
 
 int i915_driver_irq_postinstall(struct drm_device *dev)
@@ -485,23 +469,28 @@ int i915_driver_irq_postinstall(struct drm_device *dev)
        drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
        int ret, num_pipes = 2;
 
-       /* Set initial unmasked IRQs to just the selected vblank pipes. */
-       dev_priv->irq_mask_reg = ~0;
-
        ret = drm_vblank_init(dev, num_pipes);
        if (ret)
                return ret;
 
        dev_priv->vblank_pipe = DRM_I915_VBLANK_PIPE_A | DRM_I915_VBLANK_PIPE_B;
-       dev_priv->irq_mask_reg &= ~I915_DISPLAY_PIPE_A_VBLANK_INTERRUPT;
-       dev_priv->irq_mask_reg &= ~I915_DISPLAY_PIPE_B_VBLANK_INTERRUPT;
 
        dev->max_vblank_count = 0xffffff; /* only 24 bits of frame count */
 
-       dev_priv->irq_mask_reg &= I915_INTERRUPT_ENABLE_MASK;
+       /* Unmask the interrupts that we always want on. */
+       dev_priv->irq_mask_reg = ~I915_INTERRUPT_ENABLE_FIX;
+
+       dev_priv->pipestat[0] = 0;
+       dev_priv->pipestat[1] = 0;
+
+       /* Disable pipe interrupt enables, clear pending pipe status */
+       I915_WRITE(PIPEASTAT, I915_READ(PIPEASTAT) & 0x8000ffff);
+       I915_WRITE(PIPEBSTAT, I915_READ(PIPEBSTAT) & 0x8000ffff);
+       /* Clear pending interrupt status */
+       I915_WRITE(IIR, I915_READ(IIR));
 
-       I915_WRITE(IMR, dev_priv->irq_mask_reg);
        I915_WRITE(IER, I915_INTERRUPT_ENABLE_MASK);
+       I915_WRITE(IMR, dev_priv->irq_mask_reg);
        (void) I915_READ(IER);
 
        opregion_enable_asle(dev);
@@ -513,7 +502,6 @@ int i915_driver_irq_postinstall(struct drm_device *dev)
 void i915_driver_irq_uninstall(struct drm_device * dev)
 {
        drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
-       u32 temp;
 
        if (!dev_priv)
                return;
@@ -521,13 +509,12 @@ void i915_driver_irq_uninstall(struct drm_device * dev)
        dev_priv->vblank_pipe = 0;
 
        I915_WRITE(HWSTAM, 0xffffffff);
+       I915_WRITE(PIPEASTAT, 0);
+       I915_WRITE(PIPEBSTAT, 0);
        I915_WRITE(IMR, 0xffffffff);
        I915_WRITE(IER, 0x0);
 
-       temp = I915_READ(PIPEASTAT);
-       I915_WRITE(PIPEASTAT, temp);
-       temp = I915_READ(PIPEBSTAT);
-       I915_WRITE(PIPEBSTAT, temp);
-       temp = I915_READ(IIR);
-       I915_WRITE(IIR, temp);
+       I915_WRITE(PIPEASTAT, I915_READ(PIPEASTAT) & 0x8000ffff);
+       I915_WRITE(PIPEBSTAT, I915_READ(PIPEBSTAT) & 0x8000ffff);
+       I915_WRITE(IIR, I915_READ(IIR));
 }
index 1787a0c7e3abf09acc363b87495190ce362db6ce..13ae731a33dba577b9a7326a9fe22daf8c1baf1c 100644 (file)
@@ -235,17 +235,15 @@ void opregion_enable_asle(struct drm_device *dev)
        struct opregion_asle *asle = dev_priv->opregion.asle;
 
        if (asle) {
-               u32 pipeb_stats = I915_READ(PIPEBSTAT);
                if (IS_MOBILE(dev)) {
-                       /* Many devices trigger events with a write to the
-                          legacy backlight controller, so we need to ensure
-                          that it's able to generate interrupts */
-                       I915_WRITE(PIPEBSTAT, pipeb_stats |=
-                                  I915_LEGACY_BLC_EVENT_ENABLE);
-                       i915_enable_irq(dev_priv, I915_ASLE_INTERRUPT |
-                                       I915_DISPLAY_PIPE_B_EVENT_INTERRUPT);
-               } else
-                       i915_enable_irq(dev_priv, I915_ASLE_INTERRUPT);
+                       unsigned long irqflags;
+
+                       spin_lock_irqsave(&dev_priv->user_irq_lock, irqflags);
+                       i915_enable_pipestat(dev_priv, 1,
+                                            I915_LEGACY_BLC_EVENT_ENABLE);
+                       spin_unlock_irqrestore(&dev_priv->user_irq_lock,
+                                              irqflags);
+               }
 
                asle->tche = ASLE_ALS_EN | ASLE_BLC_EN | ASLE_PFIT_EN |
                        ASLE_PFMB_EN;