This patch adds minimal pm.c and sleep.S for omap2.
Please note that it does not contain suspend or voltage scaling yet.
obj-$(CONFIG_OMAP_MPU_TIMER) += timer-gp.o
+# Power Management
+obj-$(CONFIG_PM) += pm.o sleep.o
+
# Specific board support
obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o
obj-$(CONFIG_MACH_OMAP_H4) += board-h4.o
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap2/pm.c
+ *
+ * OMAP2 Power Management Routines
+ *
+ * Copyright (C) 2006 Nokia Corporation
+ * Tony Lindgren <tony@atomide.com>
+ *
+ * Copyright (C) 2005 Texas Instruments, Inc.
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * Based on pm.c for omap1
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/pm.h>
+#include <linux/sched.h>
+#include <linux/proc_fs.h>
+#include <linux/pm.h>
+#include <linux/interrupt.h>
+#include <linux/sysfs.h>
+#include <linux/module.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/atomic.h>
+#include <asm/mach/time.h>
+#include <asm/mach/irq.h>
+#include <asm/mach-types.h>
+
+#include <asm/arch/irqs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sram.h>
+#include <asm/arch/pm.h>
+
+static struct clk *vclk;
+static void (*omap2_sram_idle)(void);
+static void (*omap2_sram_suspend)(int dllctrl, int cpu_rev);
+static void (*saved_idle)(void);
+
+void omap2_pm_idle(void)
+{
+ local_irq_disable();
+ local_fiq_disable();
+ if (need_resched()) {
+ local_fiq_enable();
+ local_irq_enable();
+ return;
+ }
+
+ /*
+ * Since an interrupt may set up a timer, we don't want to
+ * reprogram the hardware timer with interrupts enabled.
+ * Re-enable interrupts only after returning from idle.
+ */
+ timer_dyn_reprogram();
+
+ omap2_sram_idle();
+ local_fiq_enable();
+ local_irq_enable();
+}
+
+static int omap2_pm_prepare(suspend_state_t state)
+{
+ int error = 0;
+
+ /* We cannot sleep in idle until we have resumed */
+ saved_idle = pm_idle;
+ pm_idle = NULL;
+
+ switch (state)
+ {
+ case PM_SUSPEND_STANDBY:
+ case PM_SUSPEND_MEM:
+ break;
+
+ case PM_SUSPEND_DISK:
+ return -ENOTSUPP;
+
+ default:
+ return -EINVAL;
+ }
+
+ return error;
+}
+
+static int omap2_pm_enter(suspend_state_t state)
+{
+ switch (state)
+ {
+ case PM_SUSPEND_STANDBY:
+ case PM_SUSPEND_MEM:
+ /* FIXME: Add suspend */
+ break;
+
+ case PM_SUSPEND_DISK:
+ return -ENOTSUPP;
+
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int omap2_pm_finish(suspend_state_t state)
+{
+ pm_idle = saved_idle;
+ return 0;
+}
+
+static struct pm_ops omap_pm_ops = {
+ .pm_disk_mode = 0,
+ .prepare = omap2_pm_prepare,
+ .enter = omap2_pm_enter,
+ .finish = omap2_pm_finish,
+};
+
+int __init omap2_pm_init(void)
+{
+ printk("Power Management for TI OMAP.\n");
+
+ vclk = clk_get(NULL, "virt_prcm_set");
+ if (IS_ERR(vclk)) {
+ printk(KERN_ERR "Could not get PM vclk\n");
+ return -ENODEV;
+ }
+
+ /*
+ * We copy the assembler sleep/wakeup routines to SRAM.
+ * These routines need to be in SRAM as that's the only
+ * memory the MPU can see when it wakes up.
+ */
+ omap2_sram_idle = omap_sram_push(omap24xx_idle_loop_suspend,
+ omap24xx_idle_loop_suspend_sz);
+
+ omap2_sram_suspend = omap_sram_push(omap24xx_cpu_suspend,
+ omap24xx_cpu_suspend_sz);
+
+ pm_set_ops(&omap_pm_ops);
+ pm_idle = omap2_pm_idle;
+
+ return 0;
+}
+
+__initcall(omap2_pm_init);
#define CM_FCLKEN_MDM PRCM_REG32(0xC00)
#define CM_ICLKEN_MDM PRCM_REG32(0xC10)
#define CM_IDLEST_MDM PRCM_REG32(0xC20)
+#define CM_AUTOIDLE_MDM PRCM_REG32(0xC30)
#define CM_CLKSEL_MDM PRCM_REG32(0xC40)
-
-/* FIXME: Move to header for 2430 */
-#define DISP_BASE (OMAP24XX_L4_IO_BASE+0x50000)
+#define CM_CLKSTCTRL_MDM PRCM_REG32(0xC48)
+#define RM_RSTCTRL_MDM PRCM_REG32(0xC50)
+#define RM_RSTST_MDM PRCM_REG32(0xC58)
+#define PM_WKEN_MDM PRCM_REG32(0xCA0)
+#define PM_WKST_MDM PRCM_REG32(0xCB0)
+#define PM_WKDEP_MDM PRCM_REG32(0xCC8)
+#define PM_PWSTCTRL_MDM PRCM_REG32(0xCE0)
+#define PM_PWSTST_MDM PRCM_REG32(0xCE4)
+
+#define OMAP24XX_L4_IO_BASE 0x48000000
+
+#define DISP_BASE (OMAP24XX_L4_IO_BASE + 0x50000)
#define DISP_REG32(offset) __REG32(DISP_BASE + (offset))
#define OMAP24XX_GPMC_BASE (L3_24XX_BASE + 0xa000)
-#define GPMC_BASE (OMAP24XX_GPMC_BASE)
-#define GPMC_REG32(offset) __REG32(GPMC_BASE + (offset))
+#define GPMC_REG32(offset) __REG32(OMAP24XX_GPMC_BASE + (offset))
-#define GPT1_BASE (OMAP24XX_GPT1)
+/* FIXME: Move these to timer code */
+#define GPT1_BASE (0x48028000)
#define GPT1_REG32(offset) __REG32(GPT1_BASE + (offset))
/* Misc sysconfig */
#define DISPC_SYSCONFIG DISP_REG32(0x410)
-#define SPI_BASE (OMAP24XX_L4_IO_BASE+0x98000)
+#define SPI_BASE (OMAP24XX_L4_IO_BASE + 0x98000)
#define MCSPI1_SYSCONFIG __REG32(SPI_BASE + 0x10)
-#define MCSPI2_SYSCONFIG __REG32(SPI_BASE+0x2000 + 0x10)
-
-//#define DSP_MMU_SYSCONFIG 0x5A000010
-#define CAMERA_MMU_SYSCONFIG __REG32(DISP_BASE+0x2C10)
-//#define IVA_MMU_SYSCONFIG 0x5D000010
-//#define DSP_DMA_SYSCONFIG 0x00FCC02C
-#define CAMERA_DMA_SYSCONFIG __REG32(DISP_BASE+0x282C)
-#define SYSTEM_DMA_SYSCONFIG __REG32(DISP_BASE+0x602C)
+#define MCSPI2_SYSCONFIG __REG32(SPI_BASE + 0x2000 + 0x10)
+#define MCSPI3_SYSCONFIG __REG32(OMAP24XX_L4_IO_BASE + 0xb8010)
+
+#define CAMERA_MMU_SYSCONFIG __REG32(DISP_BASE + 0x2C10)
+#define CAMERA_DMA_SYSCONFIG __REG32(DISP_BASE + 0x282C)
+#define SYSTEM_DMA_SYSCONFIG __REG32(DISP_BASE + 0x602C)
#define GPMC_SYSCONFIG GPMC_REG32(0x010)
-#define MAILBOXES_SYSCONFIG __REG32(OMAP24XX_L4_IO_BASE+0x94010)
-#define UART1_SYSCONFIG __REG32(OMAP24XX_L4_IO_BASE+0x6A054)
-#define UART2_SYSCONFIG __REG32(OMAP24XX_L4_IO_BASE+0x6C054)
-#define UART3_SYSCONFIG __REG32(OMAP24XX_L4_IO_BASE+0x6E054)
-//#define IVA_SYSCONFIG 0x5C060010
-#define SDRC_SYSCONFIG __REG32(OMAP24XX_SDRC_BASE+0x10)
-#define SMS_SYSCONFIG __REG32(OMAP24XX_SMS_BASE+0x10)
-#define SSI_SYSCONFIG __REG32(DISP_BASE+0x8010)
-//#define VLYNQ_SYSCONFIG 0x67FFFE10
+#define MAILBOXES_SYSCONFIG __REG32(OMAP24XX_L4_IO_BASE + 0x94010)
+#define UART1_SYSCONFIG __REG32(OMAP24XX_L4_IO_BASE + 0x6A054)
+#define UART2_SYSCONFIG __REG32(OMAP24XX_L4_IO_BASE + 0x6C054)
+#define UART3_SYSCONFIG __REG32(OMAP24XX_L4_IO_BASE + 0x6E054)
+#define SDRC_SYSCONFIG __REG32(OMAP24XX_SDRC_BASE + 0x10)
+#define OMAP24XX_SMS_BASE (L3_24XX_BASE + 0x8000)
+#define SMS_SYSCONFIG __REG32(OMAP24XX_SMS_BASE + 0x10)
+#define SSI_SYSCONFIG __REG32(DISP_BASE + 0x8010)
/* rkw - good cannidates for PM_ to start what nm was trying */
-#define OMAP24XX_GPT2 (OMAP24XX_L4_IO_BASE+0x2A000)
-#define OMAP24XX_GPT3 (OMAP24XX_L4_IO_BASE+0x78000)
-#define OMAP24XX_GPT4 (OMAP24XX_L4_IO_BASE+0x7A000)
-#define OMAP24XX_GPT5 (OMAP24XX_L4_IO_BASE+0x7C000)
-#define OMAP24XX_GPT6 (OMAP24XX_L4_IO_BASE+0x7E000)
-#define OMAP24XX_GPT7 (OMAP24XX_L4_IO_BASE+0x80000)
-#define OMAP24XX_GPT8 (OMAP24XX_L4_IO_BASE+0x82000)
-#define OMAP24XX_GPT9 (OMAP24XX_L4_IO_BASE+0x84000)
-#define OMAP24XX_GPT10 (OMAP24XX_L4_IO_BASE+0x86000)
-#define OMAP24XX_GPT11 (OMAP24XX_L4_IO_BASE+0x88000)
-#define OMAP24XX_GPT12 (OMAP24XX_L4_IO_BASE+0x8A000)
-
+#define OMAP24XX_GPT2 (OMAP24XX_L4_IO_BASE + 0x2A000)
+#define OMAP24XX_GPT3 (OMAP24XX_L4_IO_BASE + 0x78000)
+#define OMAP24XX_GPT4 (OMAP24XX_L4_IO_BASE + 0x7A000)
+#define OMAP24XX_GPT5 (OMAP24XX_L4_IO_BASE + 0x7C000)
+#define OMAP24XX_GPT6 (OMAP24XX_L4_IO_BASE + 0x7E000)
+#define OMAP24XX_GPT7 (OMAP24XX_L4_IO_BASE + 0x80000)
+#define OMAP24XX_GPT8 (OMAP24XX_L4_IO_BASE + 0x82000)
+#define OMAP24XX_GPT9 (OMAP24XX_L4_IO_BASE + 0x84000)
+#define OMAP24XX_GPT10 (OMAP24XX_L4_IO_BASE + 0x86000)
+#define OMAP24XX_GPT11 (OMAP24XX_L4_IO_BASE + 0x88000)
+#define OMAP24XX_GPT12 (OMAP24XX_L4_IO_BASE + 0x8A000)
+
+/* FIXME: Move these to timer code */
#define GPTIMER1_SYSCONFIG GPT1_REG32(0x010)
#define GPTIMER2_SYSCONFIG __REG32(OMAP24XX_GPT2 + 0x10)
#define GPTIMER3_SYSCONFIG __REG32(OMAP24XX_GPT3 + 0x10)
#define GPTIMER11_SYSCONFIG __REG32(OMAP24XX_GPT11 + 0x10)
#define GPTIMER12_SYSCONFIG __REG32(OMAP24XX_GPT12 + 0x10)
-#define GPIOX_BASE(X) (OMAP24XX_GPIO_BASE+(0x2000*((X)-1)))
+/* FIXME: Move these to gpio code */
+#define OMAP24XX_GPIO_BASE 0x48018000
+#define GPIOX_BASE(X) (OMAP24XX_GPIO_BASE + (0x2000 * ((X) - 1)))
-#define GPIO1_SYSCONFIG __REG32((GPIOX_BASE(1)+0x10))
-#define GPIO2_SYSCONFIG __REG32((GPIOX_BASE(2)+0x10))
-#define GPIO3_SYSCONFIG __REG32((GPIOX_BASE(3)+0x10))
-#define GPIO4_SYSCONFIG __REG32((GPIOX_BASE(4)+0x10))
+#define GPIO1_SYSCONFIG __REG32((GPIOX_BASE(1) + 0x10))
+#define GPIO2_SYSCONFIG __REG32((GPIOX_BASE(2) + 0x10))
+#define GPIO3_SYSCONFIG __REG32((GPIOX_BASE(3) + 0x10))
+#define GPIO4_SYSCONFIG __REG32((GPIOX_BASE(4) + 0x10))
+
+#if defined(CONFIG_ARCH_OMAP243X)
+#define GPIO5_SYSCONFIG __REG32((OMAP24XX_GPIO5_BASE + 0x10))
+#endif
/* GP TIMER 1 */
#define GPTIMER1_TISTAT GPT1_REG32(0x014)
#define GPTIMER1_TCAR2 GPT1_REG32(0x044)
/* rkw -- base fix up please... */
-#define GPTIMER3_TISR __REG32(OMAP24XX_L4_IO_BASE+0x78018)
+#define GPTIMER3_TISR __REG32(OMAP24XX_L4_IO_BASE + 0x78018)
/* SDRC */
-#define SDRC_DLLA_CTRL __REG32(OMAP24XX_SDRC_BASE+0x060)
-#define SDRC_DLLA_STATUS __REG32(OMAP24XX_SDRC_BASE+0x064)
-#define SDRC_DLLB_CTRL __REG32(OMAP24XX_SDRC_BASE+0x068)
-#define SDRC_DLLB_STATUS __REG32(OMAP24XX_SDRC_BASE+0x06C)
-#define SDRC_POWER __REG32(OMAP24XX_SDRC_BASE+0x070)
-#define SDRC_MR_0 __REG32(OMAP24XX_SDRC_BASE+0x084)
+#define SDRC_DLLA_CTRL __REG32(OMAP24XX_SDRC_BASE + 0x060)
+#define SDRC_DLLA_STATUS __REG32(OMAP24XX_SDRC_BASE + 0x064)
+#define SDRC_DLLB_CTRL __REG32(OMAP24XX_SDRC_BASE + 0x068)
+#define SDRC_DLLB_STATUS __REG32(OMAP24XX_SDRC_BASE + 0x06C)
+#define SDRC_POWER __REG32(OMAP24XX_SDRC_BASE + 0x070)
+#define SDRC_MR_0 __REG32(OMAP24XX_SDRC_BASE + 0x084)
/* GPIO 1 */
#define GPIO1_BASE GPIOX_BASE(1)
#define GPIO2_DATAIN GPIO2_REG32(0x038)
#define GPIO2_OE GPIO2_REG32(0x034)
#define GPIO2_DATAOUT GPIO2_REG32(0x03C)
+#define GPIO2_DEBOUNCENABLE GPIO2_REG32(0x050)
+#define GPIO2_DEBOUNCINGTIME GPIO2_REG32(0x054)
/* GPIO 3 */
#define GPIO3_BASE GPIOX_BASE(3)
#define GPIO3_DATAOUT GPIO3_REG32(0x03C)
#define GPIO3_DEBOUNCENABLE GPIO3_REG32(0x050)
#define GPIO3_DEBOUNCINGTIME GPIO3_REG32(0x054)
+#define GPIO3_DEBOUNCENABLE GPIO3_REG32(0x050)
+#define GPIO3_DEBOUNCINGTIME GPIO3_REG32(0x054)
/* GPIO 4 */
#define GPIO4_BASE GPIOX_BASE(4)
#define GPIO4_DEBOUNCENABLE GPIO4_REG32(0x050)
#define GPIO4_DEBOUNCINGTIME GPIO4_REG32(0x054)
+#if defined(CONFIG_ARCH_OMAP243X)
+/* GPIO 5 */
+#define GPIO5_REG32(offset) __REG32((OMAP24XX_GPIO5_BASE + (offset)))
+#define GPIO5_IRQENABLE1 GPIO5_REG32(0x01C)
+#define GPIO5_IRQSTATUS1 GPIO5_REG32(0x018)
+#define GPIO5_IRQENABLE2 GPIO5_REG32(0x02C)
+#define GPIO5_IRQSTATUS2 GPIO5_REG32(0x028)
+#define GPIO5_WAKEUPENABLE GPIO5_REG32(0x020)
+#define GPIO5_RISINGDETECT GPIO5_REG32(0x048)
+#define GPIO5_FALLINGDETECT GPIO5_REG32(0x04C)
+#define GPIO5_DATAIN GPIO5_REG32(0x038)
+#define GPIO5_OE GPIO5_REG32(0x034)
+#define GPIO5_DATAOUT GPIO5_REG32(0x03C)
+#define GPIO5_DEBOUNCENABLE GPIO5_REG32(0x050)
+#define GPIO5_DEBOUNCINGTIME GPIO5_REG32(0x054)
+#endif
/* IO CONFIG */
-#define CONTROL_BASE (OMAP24XX_CTRL_BASE)
-#define CONTROL_REG32(offset) __REG32(CONTROL_BASE + (offset))
+#define OMAP24XX_CTRL_BASE (L4_24XX_BASE)
+#define CONTROL_REG32(offset) __REG32(OMAP24XX_CTRL_BASE + (offset))
#define CONTROL_PADCONF_SPI1_NCS2 CONTROL_REG32(0x104)
#define CONTROL_PADCONF_SYS_XTALOUT CONTROL_REG32(0x134)
#define CONTROL_PADCONF_MCBSP1_DX CONTROL_REG32(0x10C)
#define CONTROL_PADCONF_GPMC_NCS4 CONTROL_REG32(0x090)
#define CONTROL_PADCONF_DSS_D5 CONTROL_REG32(0x0B8)
-#define CONTROL_PADCONF_DSS_D9 CONTROL_REG32(0x0BC)
+#define CONTROL_PADCONF_DSS_D9 CONTROL_REG32(0x0BC) /* 2420 */
#define CONTROL_PADCONF_DSS_D13 CONTROL_REG32(0x0C0)
#define CONTROL_PADCONF_DSS_VSYNC CONTROL_REG32(0x0CC)
+#define CONTROL_PADCONF_SYS_NIRQW0 CONTROL_REG32(0x0BC) /* 2430 */
+#define CONTROL_PADCONF_SSI1_FLAG_TX CONTROL_REG32(0x108) /* 2430 */
/* CONTROL */
#define CONTROL_DEVCONF CONTROL_REG32(0x274)
+#define CONTROL_DEVCONF1 CONTROL_REG32(0x2E8)
/* INTERRUPT CONTROLLER */
-#define INTC_BASE (OMAP24XX_L4_IO_BASE+0xfe000)
+#define INTC_BASE ((L4_24XX_BASE) + 0xfe000)
#define INTC_REG32(offset) __REG32(INTC_BASE + (offset))
#define INTC1_U_BASE INTC_REG32(0x000)
#define INTC_ISR_CLEAR2 INTC_REG32(0x0D4)
#define INTC_SIR_IRQ INTC_REG32(0x040)
#define INTC_CONTROL INTC_REG32(0x048)
-#define INTC_ILR11 INTC_REG32(0x12C)
+#define INTC_ILR11 INTC_REG32(0x12C) /* PRCM on MPU PIC */
+#define INTC_ILR30 INTC_REG32(0x178)
+#define INTC_ILR31 INTC_REG32(0x17C)
#define INTC_ILR32 INTC_REG32(0x180)
-#define INTC_ILR37 INTC_REG32(0x194)
-#define INTC_SYSCONFIG INTC_REG32(0x010)
+#define INTC_ILR37 INTC_REG32(0x194) /* GPIO4 on MPU PIC */
+#define INTC_SYSCONFIG INTC_REG32(0x010) /* GPT1 on MPU PIC */
/* RAM FIREWALL */
#define RAMFW_BASE (0x68005000)
#define DISPC_DATA_CYCLE2 DISP_REG32(0x5D8)
#define DISPC_DATA_CYCLE3 DISP_REG32(0x5DC)
-/* Wake up define for board */
-#define GPIO97 (1 << 1)
-#define GPIO88 (1 << 24)
+/* HSUSB Suspend */
+#define HSUSB_CTRL __REG8(0x480AC001)
+#define USBOTG_POWER __REG32(0x480AC000)
+
+/* HS MMC */
+#define MMCHS1_SYSCONFIG __REG32(0x4809C010)
+#define MMCHS2_SYSCONFIG __REG32(0x480b4010)
-#endif /* __ASSEMBLER__ */
+#endif /* __ASSEMBLER__ */
#endif
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap2/sleep.S
+ *
+ * (C) Copyright 2004
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <linux/config.h>
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+#include <asm/arch/io.h>
+#include <asm/arch/pm.h>
+
+#define A_32KSYNC_CR_V IO_ADDRESS(OMAP_TIMER32K_BASE+0x10)
+#define A_PRCM_VOLTCTRL_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x50)
+#define A_PRCM_CLKCFG_CTRL_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x80)
+#define A_CM_CLKEN_PLL_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x500)
+#define A_CM_IDLEST_CKGEN_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x520)
+#define A_CM_CLKSEL1_PLL_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x540)
+#define A_CM_CLKSEL2_PLL_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x544)
+
+#define A_SDRC_DLLA_CTRL_V IO_ADDRESS(OMAP24XX_SDRC_BASE+0x60)
+#define A_SDRC_POWER_V IO_ADDRESS(OMAP24XX_SDRC_BASE+0x70)
+#define A_SDRC_RFR_CTRL_V IO_ADDRESS(OMAP24XX_SDRC_BASE+0xA4)
+#define A_SDRC0_V (0xC0000000)
+#define A_SDRC_MANUAL_V IO_ADDRESS(OMAP24XX_SDRC_BASE+0xA8)
+
+ .text
+
+/*
+ * Forces OMAP into idle state
+ *
+ * omap24xx_idle_loop_suspend() - This bit of code just executes the WFI
+ * for normal idles.
+ *
+ * Note: This code get's copied to internal SRAM at boot. When the OMAP
+ * wakes up it continues execution at the point it went to sleep.
+ */
+ENTRY(omap24xx_idle_loop_suspend)
+ stmfd sp!, {r0, lr} @ save registers on stack
+ mov r0, #0 @ clear for mcr setup
+ mcr p15, 0, r0, c7, c0, 4 @ wait for interrupt
+ ldmfd sp!, {r0, pc} @ restore regs and return
+
+ENTRY(omap24xx_idle_loop_suspend_sz)
+ .word . - omap24xx_idle_loop_suspend
+
+/*
+ * omap242x_cpu_suspend() - Forces OMAP into deep sleep state by completing
+ * SDRC shutdown then ARM shutdown. Upon wake MPU is back on so just restore
+ * SDRC.
+ *
+ * Input:
+ * R0 : DLL ctrl value pre-Sleep
+ * R1 : Processor+Revision
+ * 2420: 0x21 = 242xES1, 0x26 = 242xES2.2
+ * 2430: 0x31 = 2430ES1, 0x32 = 2430ES2
+ *
+ * The if the DPLL is going to AutoIdle. It seems like the DPLL may be back on
+ * when we get called, but the DLL probably isn't. We will wait a bit more in
+ * case the DPLL isn't quite there yet. The code will wait on DLL for DDR even
+ * if in unlocked mode.
+ *
+ * For less than 242x-ES2.2 upon wake from a sleep mode where the external
+ * oscillator was stopped, a timing bug exists where a non-stabilized 12MHz
+ * clock can pass into the PRCM can cause problems at DSP and IVA.
+ * To work around this the code will switch to the 32kHz source prior to sleep.
+ * Post sleep we will shift back to using the DPLL. Apparently,
+ * CM_IDLEST_CLKGEN does not reflect the full clock change so you need to wait
+ * 3x12MHz + 3x32kHz clocks for a full switch.
+ *
+ * The DLL load value is not kept in RETENTION or OFF. It needs to be restored
+ * at wake
+ */
+ENTRY(omap24xx_cpu_suspend)
+ stmfd sp!, {r0 - r12, lr} @ save registers on stack
+ mov r3, #0x0 @ clear for mrc call
+ mcr p15, 0, r3, c7, c10, 4 @ memory barrier, hope SDR/DDR finished
+ nop
+ nop
+ ldr r3, A_SDRC_POWER @ addr of sdrc power
+ ldr r4, [r3] @ value of sdrc power
+ orr r4, r4, #0x40 @ enable self refresh on idle req
+ mov r5, #0x2000 @ set delay (DPLL relock + DLL relock)
+ str r4, [r3] @ make it so
+ mov r2, #0
+ nop
+ mcr p15, 0, r2, c7, c0, 4 @ wait for interrupt
+ nop
+loop:
+ subs r5, r5, #0x1 @ awake, wait just a bit
+ bne loop
+
+ /* The DPLL has on before we take the DDR out of self refresh */
+ bic r4, r4, #0x40 @ now clear self refresh bit.
+ str r4, [r3] @ put vlaue back.
+ ldr r4, A_SDRC0 @ make a clock happen
+ ldr r4, [r4]
+ nop @ start auto refresh only after clk ok
+ movs r0, r0 @ see if DDR or SDR
+ ldrne r1, A_SDRC_DLLA_CTRL_S @ get addr of DLL ctrl
+ strne r0, [r1] @ rewrite DLLA to force DLL reload
+ addne r1, r1, #0x8 @ move to DLLB
+ strne r0, [r1] @ rewrite DLLB to force DLL reload
+
+ mov r5, #0x1000
+loop2:
+ subs r5, r5, #0x1
+ bne loop2
+ /* resume*/
+ ldmfd sp!, {r0 - r12, pc} @ restore regs and return
+
+A_SDRC_POWER:
+ .word A_SDRC_POWER_V
+A_SDRC0:
+ .word A_SDRC0_V
+A_CM_CLKSEL2_PLL_S:
+ .word A_CM_CLKSEL2_PLL_V
+A_CM_CLKEN_PLL:
+ .word A_CM_CLKEN_PLL_V
+A_SDRC_DLLA_CTRL_S:
+ .word A_SDRC_DLLA_CTRL_V
+A_SDRC_MANUAL_S:
+ .word A_SDRC_MANUAL_V
+
+ENTRY(omap24xx_cpu_suspend_sz)
+ .word . - omap24xx_cpu_suspend
+
/*
* ----------------------------------------------------------------------------
- * Powermanagement bitmasks
+ * Power management bitmasks
* ----------------------------------------------------------------------------
*/
#define IDLE_WAIT_CYCLES 0x00000fff
extern void omap730_cpu_suspend(unsigned short, unsigned short);
extern void omap1510_cpu_suspend(unsigned short, unsigned short);
extern void omap1610_cpu_suspend(unsigned short, unsigned short);
+extern void omap24xx_cpu_suspend(u32 dll_ctrl, u32 cpu_revision);
extern void omap730_idle_loop_suspend(void);
extern void omap1510_idle_loop_suspend(void);
extern void omap1610_idle_loop_suspend(void);
+extern void omap24xx_idle_loop_suspend(void);
+
+extern unsigned int omap730_cpu_suspend_sz;
+extern unsigned int omap1510_cpu_suspend_sz;
+extern unsigned int omap1610_cpu_suspend_sz;
+extern unsigned int omap24xx_cpu_suspend_sz;
+extern unsigned int omap730_idle_loop_suspend_sz;
+extern unsigned int omap1510_idle_loop_suspend_sz;
+extern unsigned int omap1610_idle_loop_suspend_sz;
+extern unsigned int omap24xx_idle_loop_suspend_sz;
#ifdef CONFIG_OMAP_SERIAL_WAKE
extern void omap_serial_wake_trigger(int enable);
#define omap_serial_wake_trigger(x) {}
#endif /* CONFIG_OMAP_SERIAL_WAKE */
-extern unsigned int omap730_cpu_suspend_sz;
-extern unsigned int omap730_idle_loop_suspend_sz;
-extern unsigned int omap1510_cpu_suspend_sz;
-extern unsigned int omap1510_idle_loop_suspend_sz;
-extern unsigned int omap1610_cpu_suspend_sz;
-extern unsigned int omap1610_idle_loop_suspend_sz;
-
#define ARM_SAVE(x) arm_sleep_save[ARM_SLEEP_SAVE_##x] = omap_readl(x)
#define ARM_RESTORE(x) omap_writel((arm_sleep_save[ARM_SLEEP_SAVE_##x]), (x))
#define ARM_SHOW(x) arm_sleep_save[ARM_SLEEP_SAVE_##x]
#define MPUI1610_RESTORE(x) omap_writel((mpui1610_sleep_save[MPUI1610_SLEEP_SAVE_##x]), (x))
#define MPUI1610_SHOW(x) mpui1610_sleep_save[MPUI1610_SLEEP_SAVE_##x]
+#define OMAP24XX_SAVE(x) omap24xx_sleep_save[OMAP24XX_SLEEP_SAVE_##x] = x
+#define OMAP24XX_RESTORE(x) x = omap24xx_sleep_save[OMAP24XX_SLEEP_SAVE_##x]
+#define OMAP24XX_SHOW(x) omap24xx_sleep_save[OMAP24XX_SLEEP_SAVE_##x]
+
/*
* List of global OMAP registers to preserve.
* More ones like CP and general purpose register values are preserved
#endif
};
+enum omap24xx_save_state {
+ OMAP24XX_SLEEP_SAVE_START = 0,
+ OMAP24XX_SLEEP_SAVE_INTC_MIR0,
+ OMAP24XX_SLEEP_SAVE_INTC_MIR1,
+ OMAP24XX_SLEEP_SAVE_INTC_MIR2,
+ OMAP24XX_SLEEP_SAVE_CM_FCLKEN1_CORE,
+ OMAP24XX_SLEEP_SAVE_CM_FCLKEN2_CORE,
+ OMAP24XX_SLEEP_SAVE_CM_ICLKEN1_CORE,
+ OMAP24XX_SLEEP_SAVE_CM_ICLKEN2_CORE,
+ OMAP24XX_SLEEP_SAVE_CM_ICLKEN4_CORE,
+ OMAP24XX_SLEEP_SAVE_GPIO1_IRQENABLE1,
+ OMAP24XX_SLEEP_SAVE_GPIO2_IRQENABLE1,
+ OMAP24XX_SLEEP_SAVE_GPIO3_IRQENABLE1,
+ OMAP24XX_SLEEP_SAVE_GPIO4_IRQENABLE1,
+ OMAP24XX_SLEEP_SAVE_GPIO3_OE,
+ OMAP24XX_SLEEP_SAVE_GPIO4_OE,
+ OMAP24XX_SLEEP_SAVE_GPIO3_RISINGDETECT,
+ OMAP24XX_SLEEP_SAVE_GPIO3_FALLINGDETECT,
+ OMAP24XX_SLEEP_SAVE_CONTROL_PADCONF_SPI1_NCS2,
+ OMAP24XX_SLEEP_SAVE_CONTROL_PADCONF_MCBSP1_DX,
+ OMAP24XX_SLEEP_SAVE_CONTROL_PADCONF_SSI1_FLAG_TX,
+ OMAP24XX_SLEEP_SAVE_CONTROL_PADCONF_SYS_NIRQW0,
+ OMAP24XX_SLEEP_SAVE_SIZE
+};
+
#endif /* ASSEMBLER */
#endif /* __ASM_ARCH_OMAP_PM_H */
projects / linux-2.6-omap-h63xx.git / commitdiff