[ARM] 4709/1: pxa: mmc: add 26MHz support for pxa3[0|1]0 mmc controller

pxa3[0|1]0 mmc controller can support 26MHz clock mode, they support
SD spec 1.1 and MMC spec 4.0 which specify high speed mode. So host
caps will include MMC_CAP_MMC_HIGHSPEED and MMC_CAP_SD_HIGHSPEED for
pxa3[0|1]0.

This patch is to add 26MHz support for them. pxa host clock will be
set to 26MHz mode when the card supported max clock rate is higher
than or equal to 26MHz.

Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

diff --git a/drivers/mmc/host/pxamci.c b/drivers/mmc/host/pxamci.c
index 1654a3330340a2bfdfb1fd740d15ed4af0e76f95..80df4b047c81a789406f46875a99f8dd377c0b0a 100644 (file)
--- a/drivers/mmc/host/pxamci.c
+++ b/drivers/mmc/host/pxamci.c
@@ -375,14 +375,23 @@ static void pxamci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
                if (host->clkrt == CLKRT_OFF)
                        clk_enable(host->clk);
 
-               /*
-                * clk might result in a lower divisor than we
-                * desire.  check for that condition and adjust
-                * as appropriate.
-                */
-               if (rate / clk > ios->clock)
-                       clk <<= 1;
-               host->clkrt = fls(clk) - 1;
+               if (ios->clock == 26000000) {
+                       /* to support 26MHz on pxa300/pxa310 */
+                       host->clkrt = 7;
+               } else {
+                       /* to handle (19.5MHz, 26MHz) */
+                       if (!clk)
+                               clk = 1;
+
+                       /*
+                        * clk might result in a lower divisor than we
+                        * desire.  check for that condition and adjust
+                        * as appropriate.
+                        */
+                       if (rate / clk > ios->clock)
+                               clk <<= 1;
+                       host->clkrt = fls(clk) - 1;
+               }
 
                /*
                 * we write clkrt on the next command
@@ -519,7 +528,8 @@ static int pxamci_probe(struct platform_device *pdev)
         * Calculate minimum clock rate, rounding up.
         */
        mmc->f_min = (host->clkrate + 63) / 64;
-       mmc->f_max = host->clkrate;
+       mmc->f_max = (cpu_is_pxa300() || cpu_is_pxa310()) ? 26000000
+                                                         : host->clkrate;
 
        mmc->ocr_avail = host->pdata ?
                         host->pdata->ocr_mask :
@@ -529,6 +539,9 @@ static int pxamci_probe(struct platform_device *pdev)
        if (!cpu_is_pxa21x() && !cpu_is_pxa25x()) {
                mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ;
                host->cmdat |= CMDAT_SDIO_INT_EN;
+               if (cpu_is_pxa300() || cpu_is_pxa310())
+                       mmc->caps |= MMC_CAP_MMC_HIGHSPEED |
+                                    MMC_CAP_SD_HIGHSPEED;
        }
 
        host->sg_cpu = dma_alloc_coherent(&pdev->dev, PAGE_SIZE, &host->sg_dma, GFP_KERNEL);