hwmon: (w83791d) add manual PWM support

Add PWM manual control.

Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

diff --git a/Documentation/hwmon/w83791d b/Documentation/hwmon/w83791d
index a67d3b7a709831bb0f32f70ab30c1695693a2606..49c0e94a118c0abb63786cd05c9dddae7139434f 100644 (file)
--- a/Documentation/hwmon/w83791d
+++ b/Documentation/hwmon/w83791d
@@ -58,29 +58,32 @@ internal state that allows no clean access (Bank with ID register is not
 currently selected). If you know the address of the chip, use a 'force'
 parameter; this will put it into a more well-behaved state first.
 
-The driver implements three temperature sensors, five fan rotation speed
-sensors, and ten voltage sensors.
+The driver implements three temperature sensors, ten voltage sensors,
+five fan rotation speed sensors and manual PWM control of each fan.
 
 Temperatures are measured in degrees Celsius and measurement resolution is 1
 degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when
 the temperature gets higher than the Overtemperature Shutdown value; it stays
 on until the temperature falls below the Hysteresis value.
 
+Voltage sensors (also known as IN sensors) report their values in millivolts.
+An alarm is triggered if the voltage has crossed a programmable minimum
+or maximum limit.
+
 Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
 triggered if the rotation speed has dropped below a programmable limit. Fan
 readings can be divided by a programmable divider (1, 2, 4, 8, 16,
 32, 64 or 128 for all fans) to give the readings more range or accuracy.
 
-Voltage sensors (also known as IN sensors) report their values in millivolts.
-An alarm is triggered if the voltage has crossed a programmable minimum
-or maximum limit.
+Each fan controlled is controlled by PWM. The PWM duty cycle can be read and
+set for each fan separately. Valid values range from 0 (stop) to 255 (full).
 
 The w83791d has a global bit used to enable beeping from the speaker when an
 alarm is triggered as well as a bitmask to enable or disable the beep for
 specific alarms. You need both the global beep enable bit and the
 corresponding beep bit to be on for a triggered alarm to sound a beep.
 
-The sysfs interface to the gloabal enable is via the sysfs beep_enable file.
+The sysfs interface to the global enable is via the sysfs beep_enable file.
 This file is used for both legacy and new code.
 
 The sysfs interface to the beep bitmask has migrated from the original legacy

diff --git a/drivers/hwmon/w83791d.c b/drivers/hwmon/w83791d.c
index 6b1cec9950ffdd6d46a19d3abbce5cfe6a5e0665..a8ff4e1267132e33bd7be0a3d3f113daf34f0d83 100644 (file)
--- a/drivers/hwmon/w83791d.c
+++ b/drivers/hwmon/w83791d.c
@@ -23,7 +23,7 @@
     Supports following chips:
 
     Chip       #vin    #fanin  #pwm    #temp   wchipid vendid  i2c     ISA
-    w83791d    10      5       3       3       0x71    0x5ca3  yes     no
+    w83791d    10      5       5       3       0x71    0x5ca3  yes     no
 
     The w83791d chip appears to be part way between the 83781d and the
     83792d. Thus, this file is derived from both the w83792d.c and
@@ -45,6 +45,7 @@
 #define NUMBER_OF_VIN          10
 #define NUMBER_OF_FANIN                5
 #define NUMBER_OF_TEMPIN       3
+#define NUMBER_OF_PWM          5
 
 /* Addresses to scan */
 static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f,
@@ -116,6 +117,14 @@ static const u8 W83791D_REG_FAN_MIN[NUMBER_OF_FANIN] = {
        0xBD,                   /* FAN 5 Count Low Limit in DataSheet */
 };
 
+static const u8 W83791D_REG_PWM[NUMBER_OF_PWM] = {
+       0x81,                   /* PWM 1 duty cycle register in DataSheet */
+       0x83,                   /* PWM 2 duty cycle register in DataSheet */
+       0x94,                   /* PWM 3 duty cycle register in DataSheet */
+       0xA0,                   /* PWM 4 duty cycle register in DataSheet */
+       0xA1,                   /* PWM 5 duty cycle register in DataSheet */
+};
+
 static const u8 W83791D_REG_FAN_CFG[2] = {
        0x84,                   /* FAN 1/2 configuration */
        0x95,                   /* FAN 3 configuration */
@@ -276,6 +285,9 @@ struct w83791d_data {
                                   two sensors with three values
                                   (cur, over, hyst)  */
 
+       /* PWMs */
+       u8 pwm[5];              /* pwm duty cycle */
+
        /* Misc */
        u32 alarms;             /* realtime status register encoding,combined */
        u8 beep_enable;         /* Global beep enable */
@@ -653,6 +665,48 @@ static struct sensor_device_attribute sda_fan_alarm[] = {
        SENSOR_ATTR(fan5_alarm, S_IRUGO, show_alarm, NULL, 22),
 };
 
+/* read/write PWMs */
+static ssize_t show_pwm(struct device *dev, struct device_attribute *attr,
+                               char *buf)
+{
+       struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+       int nr = sensor_attr->index;
+       struct w83791d_data *data = w83791d_update_device(dev);
+       return sprintf(buf, "%u\n", data->pwm[nr]);
+}
+
+static ssize_t store_pwm(struct device *dev, struct device_attribute *attr,
+               const char *buf, size_t count)
+{
+       struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+       struct i2c_client *client = to_i2c_client(dev);
+       struct w83791d_data *data = i2c_get_clientdata(client);
+       int nr = sensor_attr->index;
+       unsigned long val;
+
+       if (strict_strtoul(buf, 10, &val))
+               return -EINVAL;
+
+       mutex_lock(&data->update_lock);
+       data->pwm[nr] = SENSORS_LIMIT(val, 0, 255);
+       w83791d_write(client, W83791D_REG_PWM[nr], data->pwm[nr]);
+       mutex_unlock(&data->update_lock);
+       return count;
+}
+
+static struct sensor_device_attribute sda_pwm[] = {
+       SENSOR_ATTR(pwm1, S_IWUSR | S_IRUGO,
+                       show_pwm, store_pwm, 0),
+       SENSOR_ATTR(pwm2, S_IWUSR | S_IRUGO,
+                       show_pwm, store_pwm, 1),
+       SENSOR_ATTR(pwm3, S_IWUSR | S_IRUGO,
+                       show_pwm, store_pwm, 2),
+       SENSOR_ATTR(pwm4, S_IWUSR | S_IRUGO,
+                       show_pwm, store_pwm, 3),
+       SENSOR_ATTR(pwm5, S_IWUSR | S_IRUGO,
+                       show_pwm, store_pwm, 4),
+};
+
 /* read/write the temperature1, includes measured value and limits */
 static ssize_t show_temp1(struct device *dev, struct device_attribute *devattr,
                                char *buf)
@@ -917,6 +971,9 @@ static struct attribute *w83791d_attributes[] = {
        &sda_beep_ctrl[1].dev_attr.attr,
        &dev_attr_cpu0_vid.attr,
        &dev_attr_vrm.attr,
+       &sda_pwm[0].dev_attr.attr,
+       &sda_pwm[1].dev_attr.attr,
+       &sda_pwm[2].dev_attr.attr,
        NULL
 };
 
@@ -930,6 +987,8 @@ static const struct attribute_group w83791d_group = {
 static struct attribute *w83791d_attributes_fanpwm45[] = {
        FAN_UNIT_ATTRS(3),
        FAN_UNIT_ATTRS(4),
+       &sda_pwm[3].dev_attr.attr,
+       &sda_pwm[4].dev_attr.attr,
        NULL
 };
 
@@ -1260,6 +1319,12 @@ static struct w83791d_data *w83791d_update_device(struct device *dev)
                for (i = 0; i < 3; i++)
                        data->fan_div[i] |= (vbat_reg >> (3 + i)) & 0x04;
 
+               /* Update PWM duty cycle */
+               for (i = 0; i < NUMBER_OF_PWM; i++) {
+                       data->pwm[i] =  w83791d_read(client,
+                                               W83791D_REG_PWM[i]);
+               }
+
                /* Update the first temperature sensor */
                for (i = 0; i < 3; i++) {
                        data->temp1[i] = w83791d_read(client,