* Move SFF related functions from libata-core.c to libata-sff.c.
ata_[bmdma_]sff_port_ops, ata_devchk(), ata_dev_try_classify(),
ata_std_dev_select(), ata_tf_to_host(), ata_busy_sleep(),
ata_wait_after_reset(), ata_wait_ready(), ata_bus_post_reset(),
ata_bus_softreset(), ata_bus_reset(), ata_std_softreset(),
sata_std_hardreset(), ata_fill_sg(), ata_fill_sg_dumb(),
ata_qc_prep(), ata_dump_qc_prep(), ata_data_xfer(),
ata_data_xfer_noirq(), ata_pio_sector(), ata_pio_sectors(),
atapi_send_cdb(), __atapi_pio_bytes(), atapi_pio_bytes(),
ata_hsm_ok_in_wq(), ata_hsm_qc_complete(), ata_hsm_move(),
ata_pio_task(), ata_qc_issue_prot(), ata_host_intr(),
ata_interrupt(), ata_std_ports()
* Make ata_pio_queue_task() global as it's now called from
libata-sff.c.
* Move SFF related stuff in include/linux/libata.h and
drivers/ata/libata.h into one place. While at it, move timing
constants into the global enum definition and fortify comments a
bit.
This patch strictly moves stuff around and as such doesn't cause any
functional difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
#include <linux/init.h>
#include <linux/list.h>
#include <linux/mm.h>
-#include <linux/highmem.h>
#include <linux/spinlock.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
.error_handler = sata_pmp_error_handler,
};
-const struct ata_port_operations ata_sff_port_ops = {
- .inherits = &ata_base_port_ops,
-
- .qc_prep = ata_qc_prep,
- .qc_issue = ata_qc_issue_prot,
-
- .freeze = ata_bmdma_freeze,
- .thaw = ata_bmdma_thaw,
- .softreset = ata_std_softreset,
- .error_handler = ata_bmdma_error_handler,
- .post_internal_cmd = ata_bmdma_post_internal_cmd,
-
- .dev_select = ata_std_dev_select,
- .check_status = ata_check_status,
- .tf_load = ata_tf_load,
- .tf_read = ata_tf_read,
- .exec_command = ata_exec_command,
- .data_xfer = ata_data_xfer,
- .irq_on = ata_irq_on,
-
- .port_start = ata_sff_port_start,
-};
-
-const struct ata_port_operations ata_bmdma_port_ops = {
- .inherits = &ata_sff_port_ops,
-
- .mode_filter = ata_pci_default_filter,
-
- .bmdma_setup = ata_bmdma_setup,
- .bmdma_start = ata_bmdma_start,
- .bmdma_stop = ata_bmdma_stop,
- .bmdma_status = ata_bmdma_status,
- .irq_clear = ata_bmdma_irq_clear,
-};
-
static unsigned int ata_dev_init_params(struct ata_device *dev,
u16 heads, u16 sectors);
static unsigned int ata_dev_set_xfermode(struct ata_device *dev);
}
}
+/**
+ * ata_noop_irq_clear - Noop placeholder for irq_clear
+ * @ap: Port associated with this ATA transaction.
+ */
+void ata_noop_irq_clear(struct ata_port *ap)
+{
+}
+
/**
* ata_tf_to_fis - Convert ATA taskfile to SATA FIS structure
* @tf: Taskfile to convert
}
#endif /* CONFIG_PM */
-
-/**
- * ata_devchk - PATA device presence detection
- * @ap: ATA channel to examine
- * @device: Device to examine (starting at zero)
- *
- * This technique was originally described in
- * Hale Landis's ATADRVR (www.ata-atapi.com), and
- * later found its way into the ATA/ATAPI spec.
- *
- * Write a pattern to the ATA shadow registers,
- * and if a device is present, it will respond by
- * correctly storing and echoing back the
- * ATA shadow register contents.
- *
- * LOCKING:
- * caller.
- */
-
-static unsigned int ata_devchk(struct ata_port *ap, unsigned int device)
-{
- struct ata_ioports *ioaddr = &ap->ioaddr;
- u8 nsect, lbal;
-
- ap->ops->dev_select(ap, device);
-
- iowrite8(0x55, ioaddr->nsect_addr);
- iowrite8(0xaa, ioaddr->lbal_addr);
-
- iowrite8(0xaa, ioaddr->nsect_addr);
- iowrite8(0x55, ioaddr->lbal_addr);
-
- iowrite8(0x55, ioaddr->nsect_addr);
- iowrite8(0xaa, ioaddr->lbal_addr);
-
- nsect = ioread8(ioaddr->nsect_addr);
- lbal = ioread8(ioaddr->lbal_addr);
-
- if ((nsect == 0x55) && (lbal == 0xaa))
- return 1; /* we found a device */
-
- return 0; /* nothing found */
-}
-
/**
* ata_dev_classify - determine device type based on ATA-spec signature
* @tf: ATA taskfile register set for device to be identified
return ATA_DEV_UNKNOWN;
}
-/**
- * ata_dev_try_classify - Parse returned ATA device signature
- * @dev: ATA device to classify (starting at zero)
- * @present: device seems present
- * @r_err: Value of error register on completion
- *
- * After an event -- SRST, E.D.D., or SATA COMRESET -- occurs,
- * an ATA/ATAPI-defined set of values is placed in the ATA
- * shadow registers, indicating the results of device detection
- * and diagnostics.
- *
- * Select the ATA device, and read the values from the ATA shadow
- * registers. Then parse according to the Error register value,
- * and the spec-defined values examined by ata_dev_classify().
- *
- * LOCKING:
- * caller.
- *
- * RETURNS:
- * Device type - %ATA_DEV_ATA, %ATA_DEV_ATAPI or %ATA_DEV_NONE.
- */
-unsigned int ata_dev_try_classify(struct ata_device *dev, int present,
- u8 *r_err)
-{
- struct ata_port *ap = dev->link->ap;
- struct ata_taskfile tf;
- unsigned int class;
- u8 err;
-
- ap->ops->dev_select(ap, dev->devno);
-
- memset(&tf, 0, sizeof(tf));
-
- ap->ops->tf_read(ap, &tf);
- err = tf.feature;
- if (r_err)
- *r_err = err;
-
- /* see if device passed diags: continue and warn later */
- if (err == 0)
- /* diagnostic fail : do nothing _YET_ */
- dev->horkage |= ATA_HORKAGE_DIAGNOSTIC;
- else if (err == 1)
- /* do nothing */ ;
- else if ((dev->devno == 0) && (err == 0x81))
- /* do nothing */ ;
- else
- return ATA_DEV_NONE;
-
- /* determine if device is ATA or ATAPI */
- class = ata_dev_classify(&tf);
-
- if (class == ATA_DEV_UNKNOWN) {
- /* If the device failed diagnostic, it's likely to
- * have reported incorrect device signature too.
- * Assume ATA device if the device seems present but
- * device signature is invalid with diagnostic
- * failure.
- */
- if (present && (dev->horkage & ATA_HORKAGE_DIAGNOSTIC))
- class = ATA_DEV_ATA;
- else
- class = ATA_DEV_NONE;
- } else if ((class == ATA_DEV_ATA) && (ata_chk_status(ap) == 0))
- class = ATA_DEV_NONE;
-
- return class;
-}
-
/**
* ata_id_string - Convert IDENTIFY DEVICE page into string
* @id: IDENTIFY DEVICE results we will examine
{
}
-
-/**
- * ata_std_dev_select - Select device 0/1 on ATA bus
- * @ap: ATA channel to manipulate
- * @device: ATA device (numbered from zero) to select
- *
- * Use the method defined in the ATA specification to
- * make either device 0, or device 1, active on the
- * ATA channel. Works with both PIO and MMIO.
- *
- * May be used as the dev_select() entry in ata_port_operations.
- *
- * LOCKING:
- * caller.
- */
-
-void ata_std_dev_select(struct ata_port *ap, unsigned int device)
-{
- u8 tmp;
-
- if (device == 0)
- tmp = ATA_DEVICE_OBS;
- else
- tmp = ATA_DEVICE_OBS | ATA_DEV1;
-
- iowrite8(tmp, ap->ioaddr.device_addr);
- ata_pause(ap); /* needed; also flushes, for mmio */
-}
-
-/**
- * ata_dev_select - Select device 0/1 on ATA bus
- * @ap: ATA channel to manipulate
- * @device: ATA device (numbered from zero) to select
- * @wait: non-zero to wait for Status register BSY bit to clear
- * @can_sleep: non-zero if context allows sleeping
- *
- * Use the method defined in the ATA specification to
- * make either device 0, or device 1, active on the
- * ATA channel.
- *
- * This is a high-level version of ata_std_dev_select(),
- * which additionally provides the services of inserting
- * the proper pauses and status polling, where needed.
- *
- * LOCKING:
- * caller.
- */
-
-void ata_dev_select(struct ata_port *ap, unsigned int device,
- unsigned int wait, unsigned int can_sleep)
-{
- if (ata_msg_probe(ap))
- ata_port_printk(ap, KERN_INFO, "ata_dev_select: ENTER, "
- "device %u, wait %u\n", device, wait);
-
- if (wait)
- ata_wait_idle(ap);
-
- ap->ops->dev_select(ap, device);
-
- if (wait) {
- if (can_sleep && ap->link.device[device].class == ATA_DEV_ATAPI)
- msleep(150);
- ata_wait_idle(ap);
- }
-}
-
/**
* ata_dump_id - IDENTIFY DEVICE info debugging output
* @id: IDENTIFY DEVICE page to dump
* LOCKING:
* Inherited from caller.
*/
-static void ata_pio_queue_task(struct ata_port *ap, void *data,
- unsigned long delay)
+void ata_pio_queue_task(struct ata_port *ap, void *data, unsigned long delay)
{
ap->port_task_data = data;
return rc;
}
-/**
- * ata_tf_to_host - issue ATA taskfile to host controller
- * @ap: port to which command is being issued
- * @tf: ATA taskfile register set
- *
- * Issues ATA taskfile register set to ATA host controller,
- * with proper synchronization with interrupt handler and
- * other threads.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- */
-
-static inline void ata_tf_to_host(struct ata_port *ap,
- const struct ata_taskfile *tf)
-{
- ap->ops->tf_load(ap, tf);
- ap->ops->exec_command(ap, tf);
-}
-
-/**
- * ata_busy_sleep - sleep until BSY clears, or timeout
- * @ap: port containing status register to be polled
- * @tmout_pat: impatience timeout
- * @tmout: overall timeout
- *
- * Sleep until ATA Status register bit BSY clears,
- * or a timeout occurs.
- *
- * LOCKING:
- * Kernel thread context (may sleep).
- *
- * RETURNS:
- * 0 on success, -errno otherwise.
- */
-int ata_busy_sleep(struct ata_port *ap,
- unsigned long tmout_pat, unsigned long tmout)
-{
- unsigned long timer_start, timeout;
- u8 status;
-
- status = ata_busy_wait(ap, ATA_BUSY, 300);
- timer_start = jiffies;
- timeout = timer_start + tmout_pat;
- while (status != 0xff && (status & ATA_BUSY) &&
- time_before(jiffies, timeout)) {
- msleep(50);
- status = ata_busy_wait(ap, ATA_BUSY, 3);
- }
-
- if (status != 0xff && (status & ATA_BUSY))
- ata_port_printk(ap, KERN_WARNING,
- "port is slow to respond, please be patient "
- "(Status 0x%x)\n", status);
-
- timeout = timer_start + tmout;
- while (status != 0xff && (status & ATA_BUSY) &&
- time_before(jiffies, timeout)) {
- msleep(50);
- status = ata_chk_status(ap);
- }
-
- if (status == 0xff)
- return -ENODEV;
-
- if (status & ATA_BUSY) {
- ata_port_printk(ap, KERN_ERR, "port failed to respond "
- "(%lu secs, Status 0x%x)\n",
- tmout / HZ, status);
- return -EBUSY;
- }
-
- return 0;
-}
-
-/**
- * ata_wait_after_reset - wait before checking status after reset
- * @ap: port containing status register to be polled
- * @deadline: deadline jiffies for the operation
- *
- * After reset, we need to pause a while before reading status.
- * Also, certain combination of controller and device report 0xff
- * for some duration (e.g. until SATA PHY is up and running)
- * which is interpreted as empty port in ATA world. This
- * function also waits for such devices to get out of 0xff
- * status.
- *
- * LOCKING:
- * Kernel thread context (may sleep).
- */
-void ata_wait_after_reset(struct ata_port *ap, unsigned long deadline)
-{
- unsigned long until = jiffies + ATA_TMOUT_FF_WAIT;
-
- if (time_before(until, deadline))
- deadline = until;
-
- /* Spec mandates ">= 2ms" before checking status. We wait
- * 150ms, because that was the magic delay used for ATAPI
- * devices in Hale Landis's ATADRVR, for the period of time
- * between when the ATA command register is written, and then
- * status is checked. Because waiting for "a while" before
- * checking status is fine, post SRST, we perform this magic
- * delay here as well.
- *
- * Old drivers/ide uses the 2mS rule and then waits for ready.
- */
- msleep(150);
-
- /* Wait for 0xff to clear. Some SATA devices take a long time
- * to clear 0xff after reset. For example, HHD424020F7SV00
- * iVDR needs >= 800ms while. Quantum GoVault needs even more
- * than that.
- *
- * Note that some PATA controllers (pata_ali) explode if
- * status register is read more than once when there's no
- * device attached.
- */
- if (ap->flags & ATA_FLAG_SATA) {
- while (1) {
- u8 status = ata_chk_status(ap);
-
- if (status != 0xff || time_after(jiffies, deadline))
- return;
-
- msleep(50);
- }
- }
-}
-
-/**
- * ata_wait_ready - sleep until BSY clears, or timeout
- * @ap: port containing status register to be polled
- * @deadline: deadline jiffies for the operation
- *
- * Sleep until ATA Status register bit BSY clears, or timeout
- * occurs.
- *
- * LOCKING:
- * Kernel thread context (may sleep).
- *
- * RETURNS:
- * 0 on success, -errno otherwise.
- */
-int ata_wait_ready(struct ata_port *ap, unsigned long deadline)
-{
- unsigned long start = jiffies;
- int warned = 0;
-
- while (1) {
- u8 status = ata_chk_status(ap);
- unsigned long now = jiffies;
-
- if (!(status & ATA_BUSY))
- return 0;
- if (!ata_link_online(&ap->link) && status == 0xff)
- return -ENODEV;
- if (time_after(now, deadline))
- return -EBUSY;
-
- if (!warned && time_after(now, start + 5 * HZ) &&
- (deadline - now > 3 * HZ)) {
- ata_port_printk(ap, KERN_WARNING,
- "port is slow to respond, please be patient "
- "(Status 0x%x)\n", status);
- warned = 1;
- }
-
- msleep(50);
- }
-}
-
-static int ata_bus_post_reset(struct ata_port *ap, unsigned int devmask,
- unsigned long deadline)
-{
- struct ata_ioports *ioaddr = &ap->ioaddr;
- unsigned int dev0 = devmask & (1 << 0);
- unsigned int dev1 = devmask & (1 << 1);
- int rc, ret = 0;
-
- /* if device 0 was found in ata_devchk, wait for its
- * BSY bit to clear
- */
- if (dev0) {
- rc = ata_wait_ready(ap, deadline);
- if (rc) {
- if (rc != -ENODEV)
- return rc;
- ret = rc;
- }
- }
-
- /* if device 1 was found in ata_devchk, wait for register
- * access briefly, then wait for BSY to clear.
- */
- if (dev1) {
- int i;
-
- ap->ops->dev_select(ap, 1);
-
- /* Wait for register access. Some ATAPI devices fail
- * to set nsect/lbal after reset, so don't waste too
- * much time on it. We're gonna wait for !BSY anyway.
- */
- for (i = 0; i < 2; i++) {
- u8 nsect, lbal;
-
- nsect = ioread8(ioaddr->nsect_addr);
- lbal = ioread8(ioaddr->lbal_addr);
- if ((nsect == 1) && (lbal == 1))
- break;
- msleep(50); /* give drive a breather */
- }
-
- rc = ata_wait_ready(ap, deadline);
- if (rc) {
- if (rc != -ENODEV)
- return rc;
- ret = rc;
- }
- }
-
- /* is all this really necessary? */
- ap->ops->dev_select(ap, 0);
- if (dev1)
- ap->ops->dev_select(ap, 1);
- if (dev0)
- ap->ops->dev_select(ap, 0);
-
- return ret;
-}
-
-static int ata_bus_softreset(struct ata_port *ap, unsigned int devmask,
- unsigned long deadline)
-{
- struct ata_ioports *ioaddr = &ap->ioaddr;
-
- DPRINTK("ata%u: bus reset via SRST\n", ap->print_id);
-
- /* software reset. causes dev0 to be selected */
- iowrite8(ap->ctl, ioaddr->ctl_addr);
- udelay(20); /* FIXME: flush */
- iowrite8(ap->ctl | ATA_SRST, ioaddr->ctl_addr);
- udelay(20); /* FIXME: flush */
- iowrite8(ap->ctl, ioaddr->ctl_addr);
-
- /* wait a while before checking status */
- ata_wait_after_reset(ap, deadline);
-
- /* Before we perform post reset processing we want to see if
- * the bus shows 0xFF because the odd clown forgets the D7
- * pulldown resistor.
- */
- if (ata_chk_status(ap) == 0xFF)
- return -ENODEV;
-
- return ata_bus_post_reset(ap, devmask, deadline);
-}
-
-/**
- * ata_bus_reset - reset host port and associated ATA channel
- * @ap: port to reset
- *
- * This is typically the first time we actually start issuing
- * commands to the ATA channel. We wait for BSY to clear, then
- * issue EXECUTE DEVICE DIAGNOSTIC command, polling for its
- * result. Determine what devices, if any, are on the channel
- * by looking at the device 0/1 error register. Look at the signature
- * stored in each device's taskfile registers, to determine if
- * the device is ATA or ATAPI.
- *
- * LOCKING:
- * PCI/etc. bus probe sem.
- * Obtains host lock.
- *
- * SIDE EFFECTS:
- * Sets ATA_FLAG_DISABLED if bus reset fails.
- */
-
-void ata_bus_reset(struct ata_port *ap)
-{
- struct ata_device *device = ap->link.device;
- struct ata_ioports *ioaddr = &ap->ioaddr;
- unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS;
- u8 err;
- unsigned int dev0, dev1 = 0, devmask = 0;
- int rc;
-
- DPRINTK("ENTER, host %u, port %u\n", ap->print_id, ap->port_no);
-
- /* determine if device 0/1 are present */
- if (ap->flags & ATA_FLAG_SATA_RESET)
- dev0 = 1;
- else {
- dev0 = ata_devchk(ap, 0);
- if (slave_possible)
- dev1 = ata_devchk(ap, 1);
- }
-
- if (dev0)
- devmask |= (1 << 0);
- if (dev1)
- devmask |= (1 << 1);
-
- /* select device 0 again */
- ap->ops->dev_select(ap, 0);
-
- /* issue bus reset */
- if (ap->flags & ATA_FLAG_SRST) {
- rc = ata_bus_softreset(ap, devmask, jiffies + 40 * HZ);
- if (rc && rc != -ENODEV)
- goto err_out;
- }
-
- /*
- * determine by signature whether we have ATA or ATAPI devices
- */
- device[0].class = ata_dev_try_classify(&device[0], dev0, &err);
- if ((slave_possible) && (err != 0x81))
- device[1].class = ata_dev_try_classify(&device[1], dev1, &err);
-
- /* is double-select really necessary? */
- if (device[1].class != ATA_DEV_NONE)
- ap->ops->dev_select(ap, 1);
- if (device[0].class != ATA_DEV_NONE)
- ap->ops->dev_select(ap, 0);
-
- /* if no devices were detected, disable this port */
- if ((device[0].class == ATA_DEV_NONE) &&
- (device[1].class == ATA_DEV_NONE))
- goto err_out;
-
- if (ap->flags & (ATA_FLAG_SATA_RESET | ATA_FLAG_SRST)) {
- /* set up device control for ATA_FLAG_SATA_RESET */
- iowrite8(ap->ctl, ioaddr->ctl_addr);
- }
-
- DPRINTK("EXIT\n");
- return;
-
-err_out:
- ata_port_printk(ap, KERN_ERR, "disabling port\n");
- ata_port_disable(ap);
-
- DPRINTK("EXIT\n");
-}
-
/**
* sata_link_debounce - debounce SATA phy status
* @link: ATA link to debounce SATA phy status for
}
/**
- * ata_std_softreset - reset host port via ATA SRST
- * @link: ATA link to reset
- * @classes: resulting classes of attached devices
+ * sata_link_hardreset - reset link via SATA phy reset
+ * @link: link to reset
+ * @timing: timing parameters { interval, duratinon, timeout } in msec
* @deadline: deadline jiffies for the operation
*
- * Reset host port using ATA SRST.
+ * SATA phy-reset @link using DET bits of SControl register.
*
* LOCKING:
* Kernel thread context (may sleep)
* RETURNS:
* 0 on success, -errno otherwise.
*/
-int ata_std_softreset(struct ata_link *link, unsigned int *classes,
- unsigned long deadline)
+int sata_link_hardreset(struct ata_link *link, const unsigned long *timing,
+ unsigned long deadline)
{
- struct ata_port *ap = link->ap;
- unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS;
- unsigned int devmask = 0;
- int rc;
- u8 err;
-
- DPRINTK("ENTER\n");
-
- if (ata_link_offline(link)) {
- classes[0] = ATA_DEV_NONE;
- goto out;
- }
-
- /* determine if device 0/1 are present */
- if (ata_devchk(ap, 0))
- devmask |= (1 << 0);
- if (slave_possible && ata_devchk(ap, 1))
- devmask |= (1 << 1);
-
- /* select device 0 again */
- ap->ops->dev_select(ap, 0);
-
- /* issue bus reset */
- DPRINTK("about to softreset, devmask=%x\n", devmask);
- rc = ata_bus_softreset(ap, devmask, deadline);
- /* if link is occupied, -ENODEV too is an error */
- if (rc && (rc != -ENODEV || sata_scr_valid(link))) {
- ata_link_printk(link, KERN_ERR, "SRST failed (errno=%d)\n", rc);
- return rc;
- }
-
- /* determine by signature whether we have ATA or ATAPI devices */
- classes[0] = ata_dev_try_classify(&link->device[0],
- devmask & (1 << 0), &err);
- if (slave_possible && err != 0x81)
- classes[1] = ata_dev_try_classify(&link->device[1],
- devmask & (1 << 1), &err);
-
- out:
- DPRINTK("EXIT, classes[0]=%u [1]=%u\n", classes[0], classes[1]);
- return 0;
-}
-
-/**
- * sata_link_hardreset - reset link via SATA phy reset
- * @link: link to reset
- * @timing: timing parameters { interval, duratinon, timeout } in msec
- * @deadline: deadline jiffies for the operation
- *
- * SATA phy-reset @link using DET bits of SControl register.
- *
- * LOCKING:
- * Kernel thread context (may sleep)
- *
- * RETURNS:
- * 0 on success, -errno otherwise.
- */
-int sata_link_hardreset(struct ata_link *link, const unsigned long *timing,
- unsigned long deadline)
-{
- u32 scontrol;
+ u32 scontrol;
int rc;
DPRINTK("ENTER\n");
return rc;
}
-/**
- * sata_std_hardreset - reset host port via SATA phy reset
- * @link: link to reset
- * @class: resulting class of attached device
- * @deadline: deadline jiffies for the operation
- *
- * SATA phy-reset host port using DET bits of SControl register,
- * wait for !BSY and classify the attached device.
- *
- * LOCKING:
- * Kernel thread context (may sleep)
- *
- * RETURNS:
- * 0 on success, -errno otherwise.
- */
-int sata_std_hardreset(struct ata_link *link, unsigned int *class,
- unsigned long deadline)
-{
- struct ata_port *ap = link->ap;
- const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context);
- int rc;
-
- DPRINTK("ENTER\n");
-
- /* do hardreset */
- rc = sata_link_hardreset(link, timing, deadline);
- if (rc) {
- ata_link_printk(link, KERN_ERR,
- "COMRESET failed (errno=%d)\n", rc);
- return rc;
- }
-
- /* TODO: phy layer with polling, timeouts, etc. */
- if (ata_link_offline(link)) {
- *class = ATA_DEV_NONE;
- DPRINTK("EXIT, link offline\n");
- return 0;
- }
-
- /* wait a while before checking status */
- ata_wait_after_reset(ap, deadline);
-
- /* If PMP is supported, we have to do follow-up SRST. Note
- * that some PMPs don't send D2H Reg FIS after hardreset at
- * all if the first port is empty. Wait for it just for a
- * second and request follow-up SRST.
- */
- if (ap->flags & ATA_FLAG_PMP) {
- ata_wait_ready(ap, jiffies + HZ);
- return -EAGAIN;
- }
-
- rc = ata_wait_ready(ap, deadline);
- /* link occupied, -ENODEV too is an error */
- if (rc) {
- ata_link_printk(link, KERN_ERR,
- "COMRESET failed (errno=%d)\n", rc);
- return rc;
- }
-
- ap->ops->dev_select(ap, 0); /* probably unnecessary */
-
- *class = ata_dev_try_classify(link->device, 1, NULL);
-
- DPRINTK("EXIT, class=%u\n", *class);
- return 0;
-}
-
/**
* ata_std_postreset - standard postreset callback
* @link: the target ata_link
qc->sg = NULL;
}
-/**
- * ata_fill_sg - Fill PCI IDE PRD table
- * @qc: Metadata associated with taskfile to be transferred
- *
- * Fill PCI IDE PRD (scatter-gather) table with segments
- * associated with the current disk command.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- *
- */
-static void ata_fill_sg(struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- struct scatterlist *sg;
- unsigned int si, pi;
-
- pi = 0;
- for_each_sg(qc->sg, sg, qc->n_elem, si) {
- u32 addr, offset;
- u32 sg_len, len;
-
- /* determine if physical DMA addr spans 64K boundary.
- * Note h/w doesn't support 64-bit, so we unconditionally
- * truncate dma_addr_t to u32.
- */
- addr = (u32) sg_dma_address(sg);
- sg_len = sg_dma_len(sg);
-
- while (sg_len) {
- offset = addr & 0xffff;
- len = sg_len;
- if ((offset + sg_len) > 0x10000)
- len = 0x10000 - offset;
-
- ap->prd[pi].addr = cpu_to_le32(addr);
- ap->prd[pi].flags_len = cpu_to_le32(len & 0xffff);
- VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", pi, addr, len);
-
- pi++;
- sg_len -= len;
- addr += len;
- }
- }
-
- ap->prd[pi - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
-}
-
-/**
- * ata_fill_sg_dumb - Fill PCI IDE PRD table
- * @qc: Metadata associated with taskfile to be transferred
- *
- * Fill PCI IDE PRD (scatter-gather) table with segments
- * associated with the current disk command. Perform the fill
- * so that we avoid writing any length 64K records for
- * controllers that don't follow the spec.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- *
- */
-static void ata_fill_sg_dumb(struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- struct scatterlist *sg;
- unsigned int si, pi;
-
- pi = 0;
- for_each_sg(qc->sg, sg, qc->n_elem, si) {
- u32 addr, offset;
- u32 sg_len, len, blen;
-
- /* determine if physical DMA addr spans 64K boundary.
- * Note h/w doesn't support 64-bit, so we unconditionally
- * truncate dma_addr_t to u32.
- */
- addr = (u32) sg_dma_address(sg);
- sg_len = sg_dma_len(sg);
-
- while (sg_len) {
- offset = addr & 0xffff;
- len = sg_len;
- if ((offset + sg_len) > 0x10000)
- len = 0x10000 - offset;
-
- blen = len & 0xffff;
- ap->prd[pi].addr = cpu_to_le32(addr);
- if (blen == 0) {
- /* Some PATA chipsets like the CS5530 can't
- cope with 0x0000 meaning 64K as the spec says */
- ap->prd[pi].flags_len = cpu_to_le32(0x8000);
- blen = 0x8000;
- ap->prd[++pi].addr = cpu_to_le32(addr + 0x8000);
- }
- ap->prd[pi].flags_len = cpu_to_le32(blen);
- VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", pi, addr, len);
-
- pi++;
- sg_len -= len;
- addr += len;
- }
- }
-
- ap->prd[pi - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
-}
-
/**
* ata_check_atapi_dma - Check whether ATAPI DMA can be supported
* @qc: Metadata associated with taskfile to check
* supplied PACKET command.
*
* LOCKING:
- * spin_lock_irqsave(host lock)
- *
- * RETURNS: 0 when ATAPI DMA can be used
- * nonzero otherwise
- */
-int ata_check_atapi_dma(struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
-
- /* Don't allow DMA if it isn't multiple of 16 bytes. Quite a
- * few ATAPI devices choke on such DMA requests.
- */
- if (unlikely(qc->nbytes & 15))
- return 1;
-
- if (ap->ops->check_atapi_dma)
- return ap->ops->check_atapi_dma(qc);
-
- return 0;
-}
-
-/**
- * ata_std_qc_defer - Check whether a qc needs to be deferred
- * @qc: ATA command in question
- *
- * Non-NCQ commands cannot run with any other command, NCQ or
- * not. As upper layer only knows the queue depth, we are
- * responsible for maintaining exclusion. This function checks
- * whether a new command @qc can be issued.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- *
- * RETURNS:
- * ATA_DEFER_* if deferring is needed, 0 otherwise.
- */
-int ata_std_qc_defer(struct ata_queued_cmd *qc)
-{
- struct ata_link *link = qc->dev->link;
-
- if (qc->tf.protocol == ATA_PROT_NCQ) {
- if (!ata_tag_valid(link->active_tag))
- return 0;
- } else {
- if (!ata_tag_valid(link->active_tag) && !link->sactive)
- return 0;
- }
-
- return ATA_DEFER_LINK;
-}
-
-/**
- * ata_qc_prep - Prepare taskfile for submission
- * @qc: Metadata associated with taskfile to be prepared
- *
- * Prepare ATA taskfile for submission.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- */
-void ata_qc_prep(struct ata_queued_cmd *qc)
-{
- if (!(qc->flags & ATA_QCFLAG_DMAMAP))
- return;
-
- ata_fill_sg(qc);
-}
-
-/**
- * ata_dumb_qc_prep - Prepare taskfile for submission
- * @qc: Metadata associated with taskfile to be prepared
- *
- * Prepare ATA taskfile for submission.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- */
-void ata_dumb_qc_prep(struct ata_queued_cmd *qc)
-{
- if (!(qc->flags & ATA_QCFLAG_DMAMAP))
- return;
-
- ata_fill_sg_dumb(qc);
-}
-
-void ata_noop_qc_prep(struct ata_queued_cmd *qc) { }
-
-/**
- * ata_sg_init - Associate command with scatter-gather table.
- * @qc: Command to be associated
- * @sg: Scatter-gather table.
- * @n_elem: Number of elements in s/g table.
- *
- * Initialize the data-related elements of queued_cmd @qc
- * to point to a scatter-gather table @sg, containing @n_elem
- * elements.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- */
-void ata_sg_init(struct ata_queued_cmd *qc, struct scatterlist *sg,
- unsigned int n_elem)
-{
- qc->sg = sg;
- qc->n_elem = n_elem;
- qc->cursg = qc->sg;
-}
-
-/**
- * ata_sg_setup - DMA-map the scatter-gather table associated with a command.
- * @qc: Command with scatter-gather table to be mapped.
- *
- * DMA-map the scatter-gather table associated with queued_cmd @qc.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- *
- * RETURNS:
- * Zero on success, negative on error.
- *
- */
-static int ata_sg_setup(struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- unsigned int n_elem;
-
- VPRINTK("ENTER, ata%u\n", ap->print_id);
-
- n_elem = dma_map_sg(ap->dev, qc->sg, qc->n_elem, qc->dma_dir);
- if (n_elem < 1)
- return -1;
-
- DPRINTK("%d sg elements mapped\n", n_elem);
-
- qc->n_elem = n_elem;
- qc->flags |= ATA_QCFLAG_DMAMAP;
-
- return 0;
-}
-
-/**
- * swap_buf_le16 - swap halves of 16-bit words in place
- * @buf: Buffer to swap
- * @buf_words: Number of 16-bit words in buffer.
- *
- * Swap halves of 16-bit words if needed to convert from
- * little-endian byte order to native cpu byte order, or
- * vice-versa.
- *
- * LOCKING:
- * Inherited from caller.
- */
-void swap_buf_le16(u16 *buf, unsigned int buf_words)
-{
-#ifdef __BIG_ENDIAN
- unsigned int i;
-
- for (i = 0; i < buf_words; i++)
- buf[i] = le16_to_cpu(buf[i]);
-#endif /* __BIG_ENDIAN */
-}
-
-/**
- * ata_data_xfer - Transfer data by PIO
- * @dev: device to target
- * @buf: data buffer
- * @buflen: buffer length
- * @rw: read/write
- *
- * Transfer data from/to the device data register by PIO.
- *
- * LOCKING:
- * Inherited from caller.
- *
- * RETURNS:
- * Bytes consumed.
- */
-unsigned int ata_data_xfer(struct ata_device *dev, unsigned char *buf,
- unsigned int buflen, int rw)
-{
- struct ata_port *ap = dev->link->ap;
- void __iomem *data_addr = ap->ioaddr.data_addr;
- unsigned int words = buflen >> 1;
-
- /* Transfer multiple of 2 bytes */
- if (rw == READ)
- ioread16_rep(data_addr, buf, words);
- else
- iowrite16_rep(data_addr, buf, words);
-
- /* Transfer trailing 1 byte, if any. */
- if (unlikely(buflen & 0x01)) {
- __le16 align_buf[1] = { 0 };
- unsigned char *trailing_buf = buf + buflen - 1;
-
- if (rw == READ) {
- align_buf[0] = cpu_to_le16(ioread16(data_addr));
- memcpy(trailing_buf, align_buf, 1);
- } else {
- memcpy(align_buf, trailing_buf, 1);
- iowrite16(le16_to_cpu(align_buf[0]), data_addr);
- }
- words++;
- }
-
- return words << 1;
-}
-
-/**
- * ata_data_xfer_noirq - Transfer data by PIO
- * @dev: device to target
- * @buf: data buffer
- * @buflen: buffer length
- * @rw: read/write
- *
- * Transfer data from/to the device data register by PIO. Do the
- * transfer with interrupts disabled.
- *
- * LOCKING:
- * Inherited from caller.
- *
- * RETURNS:
- * Bytes consumed.
- */
-unsigned int ata_data_xfer_noirq(struct ata_device *dev, unsigned char *buf,
- unsigned int buflen, int rw)
-{
- unsigned long flags;
- unsigned int consumed;
-
- local_irq_save(flags);
- consumed = ata_data_xfer(dev, buf, buflen, rw);
- local_irq_restore(flags);
-
- return consumed;
-}
-
-
-/**
- * ata_pio_sector - Transfer a sector of data.
- * @qc: Command on going
- *
- * Transfer qc->sect_size bytes of data from/to the ATA device.
- *
- * LOCKING:
- * Inherited from caller.
- */
-
-static void ata_pio_sector(struct ata_queued_cmd *qc)
-{
- int do_write = (qc->tf.flags & ATA_TFLAG_WRITE);
- struct ata_port *ap = qc->ap;
- struct page *page;
- unsigned int offset;
- unsigned char *buf;
-
- if (qc->curbytes == qc->nbytes - qc->sect_size)
- ap->hsm_task_state = HSM_ST_LAST;
-
- page = sg_page(qc->cursg);
- offset = qc->cursg->offset + qc->cursg_ofs;
-
- /* get the current page and offset */
- page = nth_page(page, (offset >> PAGE_SHIFT));
- offset %= PAGE_SIZE;
-
- DPRINTK("data %s\n", qc->tf.flags & ATA_TFLAG_WRITE ? "write" : "read");
-
- if (PageHighMem(page)) {
- unsigned long flags;
-
- /* FIXME: use a bounce buffer */
- local_irq_save(flags);
- buf = kmap_atomic(page, KM_IRQ0);
-
- /* do the actual data transfer */
- ap->ops->data_xfer(qc->dev, buf + offset, qc->sect_size, do_write);
-
- kunmap_atomic(buf, KM_IRQ0);
- local_irq_restore(flags);
- } else {
- buf = page_address(page);
- ap->ops->data_xfer(qc->dev, buf + offset, qc->sect_size, do_write);
- }
-
- qc->curbytes += qc->sect_size;
- qc->cursg_ofs += qc->sect_size;
-
- if (qc->cursg_ofs == qc->cursg->length) {
- qc->cursg = sg_next(qc->cursg);
- qc->cursg_ofs = 0;
- }
-}
-
-/**
- * ata_pio_sectors - Transfer one or many sectors.
- * @qc: Command on going
- *
- * Transfer one or many sectors of data from/to the
- * ATA device for the DRQ request.
- *
- * LOCKING:
- * Inherited from caller.
- */
-
-static void ata_pio_sectors(struct ata_queued_cmd *qc)
-{
- if (is_multi_taskfile(&qc->tf)) {
- /* READ/WRITE MULTIPLE */
- unsigned int nsect;
-
- WARN_ON(qc->dev->multi_count == 0);
-
- nsect = min((qc->nbytes - qc->curbytes) / qc->sect_size,
- qc->dev->multi_count);
- while (nsect--)
- ata_pio_sector(qc);
- } else
- ata_pio_sector(qc);
-
- ata_altstatus(qc->ap); /* flush */
-}
-
-/**
- * atapi_send_cdb - Write CDB bytes to hardware
- * @ap: Port to which ATAPI device is attached.
- * @qc: Taskfile currently active
- *
- * When device has indicated its readiness to accept
- * a CDB, this function is called. Send the CDB.
- *
- * LOCKING:
- * caller.
- */
-
-static void atapi_send_cdb(struct ata_port *ap, struct ata_queued_cmd *qc)
-{
- /* send SCSI cdb */
- DPRINTK("send cdb\n");
- WARN_ON(qc->dev->cdb_len < 12);
-
- ap->ops->data_xfer(qc->dev, qc->cdb, qc->dev->cdb_len, 1);
- ata_altstatus(ap); /* flush */
-
- switch (qc->tf.protocol) {
- case ATAPI_PROT_PIO:
- ap->hsm_task_state = HSM_ST;
- break;
- case ATAPI_PROT_NODATA:
- ap->hsm_task_state = HSM_ST_LAST;
- break;
- case ATAPI_PROT_DMA:
- ap->hsm_task_state = HSM_ST_LAST;
- /* initiate bmdma */
- ap->ops->bmdma_start(qc);
- break;
- }
-}
-
-/**
- * __atapi_pio_bytes - Transfer data from/to the ATAPI device.
- * @qc: Command on going
- * @bytes: number of bytes
- *
- * Transfer Transfer data from/to the ATAPI device.
- *
- * LOCKING:
- * Inherited from caller.
- *
- */
-static int __atapi_pio_bytes(struct ata_queued_cmd *qc, unsigned int bytes)
-{
- int rw = (qc->tf.flags & ATA_TFLAG_WRITE) ? WRITE : READ;
- struct ata_port *ap = qc->ap;
- struct ata_device *dev = qc->dev;
- struct ata_eh_info *ehi = &dev->link->eh_info;
- struct scatterlist *sg;
- struct page *page;
- unsigned char *buf;
- unsigned int offset, count, consumed;
-
-next_sg:
- sg = qc->cursg;
- if (unlikely(!sg)) {
- ata_ehi_push_desc(ehi, "unexpected or too much trailing data "
- "buf=%u cur=%u bytes=%u",
- qc->nbytes, qc->curbytes, bytes);
- return -1;
- }
-
- page = sg_page(sg);
- offset = sg->offset + qc->cursg_ofs;
-
- /* get the current page and offset */
- page = nth_page(page, (offset >> PAGE_SHIFT));
- offset %= PAGE_SIZE;
-
- /* don't overrun current sg */
- count = min(sg->length - qc->cursg_ofs, bytes);
-
- /* don't cross page boundaries */
- count = min(count, (unsigned int)PAGE_SIZE - offset);
-
- DPRINTK("data %s\n", qc->tf.flags & ATA_TFLAG_WRITE ? "write" : "read");
-
- if (PageHighMem(page)) {
- unsigned long flags;
-
- /* FIXME: use bounce buffer */
- local_irq_save(flags);
- buf = kmap_atomic(page, KM_IRQ0);
-
- /* do the actual data transfer */
- consumed = ap->ops->data_xfer(dev, buf + offset, count, rw);
-
- kunmap_atomic(buf, KM_IRQ0);
- local_irq_restore(flags);
- } else {
- buf = page_address(page);
- consumed = ap->ops->data_xfer(dev, buf + offset, count, rw);
- }
-
- bytes -= min(bytes, consumed);
- qc->curbytes += count;
- qc->cursg_ofs += count;
-
- if (qc->cursg_ofs == sg->length) {
- qc->cursg = sg_next(qc->cursg);
- qc->cursg_ofs = 0;
- }
-
- /* consumed can be larger than count only for the last transfer */
- WARN_ON(qc->cursg && count != consumed);
-
- if (bytes)
- goto next_sg;
- return 0;
-}
-
-/**
- * atapi_pio_bytes - Transfer data from/to the ATAPI device.
- * @qc: Command on going
- *
- * Transfer Transfer data from/to the ATAPI device.
- *
- * LOCKING:
- * Inherited from caller.
- */
-
-static void atapi_pio_bytes(struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- struct ata_device *dev = qc->dev;
- struct ata_eh_info *ehi = &dev->link->eh_info;
- unsigned int ireason, bc_lo, bc_hi, bytes;
- int i_write, do_write = (qc->tf.flags & ATA_TFLAG_WRITE) ? 1 : 0;
-
- /* Abuse qc->result_tf for temp storage of intermediate TF
- * here to save some kernel stack usage.
- * For normal completion, qc->result_tf is not relevant. For
- * error, qc->result_tf is later overwritten by ata_qc_complete().
- * So, the correctness of qc->result_tf is not affected.
- */
- ap->ops->tf_read(ap, &qc->result_tf);
- ireason = qc->result_tf.nsect;
- bc_lo = qc->result_tf.lbam;
- bc_hi = qc->result_tf.lbah;
- bytes = (bc_hi << 8) | bc_lo;
-
- /* shall be cleared to zero, indicating xfer of data */
- if (unlikely(ireason & (1 << 0)))
- goto atapi_check;
-
- /* make sure transfer direction matches expected */
- i_write = ((ireason & (1 << 1)) == 0) ? 1 : 0;
- if (unlikely(do_write != i_write))
- goto atapi_check;
-
- if (unlikely(!bytes))
- goto atapi_check;
-
- VPRINTK("ata%u: xfering %d bytes\n", ap->print_id, bytes);
-
- if (unlikely(__atapi_pio_bytes(qc, bytes)))
- goto err_out;
- ata_altstatus(ap); /* flush */
-
- return;
-
- atapi_check:
- ata_ehi_push_desc(ehi, "ATAPI check failed (ireason=0x%x bytes=%u)",
- ireason, bytes);
- err_out:
- qc->err_mask |= AC_ERR_HSM;
- ap->hsm_task_state = HSM_ST_ERR;
-}
-
-/**
- * ata_hsm_ok_in_wq - Check if the qc can be handled in the workqueue.
- * @ap: the target ata_port
- * @qc: qc on going
- *
- * RETURNS:
- * 1 if ok in workqueue, 0 otherwise.
- */
-
-static inline int ata_hsm_ok_in_wq(struct ata_port *ap, struct ata_queued_cmd *qc)
-{
- if (qc->tf.flags & ATA_TFLAG_POLLING)
- return 1;
-
- if (ap->hsm_task_state == HSM_ST_FIRST) {
- if (qc->tf.protocol == ATA_PROT_PIO &&
- (qc->tf.flags & ATA_TFLAG_WRITE))
- return 1;
-
- if (ata_is_atapi(qc->tf.protocol) &&
- !(qc->dev->flags & ATA_DFLAG_CDB_INTR))
- return 1;
- }
-
- return 0;
-}
-
-/**
- * ata_hsm_qc_complete - finish a qc running on standard HSM
- * @qc: Command to complete
- * @in_wq: 1 if called from workqueue, 0 otherwise
- *
- * Finish @qc which is running on standard HSM.
- *
- * LOCKING:
- * If @in_wq is zero, spin_lock_irqsave(host lock).
- * Otherwise, none on entry and grabs host lock.
- */
-static void ata_hsm_qc_complete(struct ata_queued_cmd *qc, int in_wq)
-{
- struct ata_port *ap = qc->ap;
- unsigned long flags;
-
- if (ap->ops->error_handler) {
- if (in_wq) {
- spin_lock_irqsave(ap->lock, flags);
-
- /* EH might have kicked in while host lock is
- * released.
- */
- qc = ata_qc_from_tag(ap, qc->tag);
- if (qc) {
- if (likely(!(qc->err_mask & AC_ERR_HSM))) {
- ap->ops->irq_on(ap);
- ata_qc_complete(qc);
- } else
- ata_port_freeze(ap);
- }
-
- spin_unlock_irqrestore(ap->lock, flags);
- } else {
- if (likely(!(qc->err_mask & AC_ERR_HSM)))
- ata_qc_complete(qc);
- else
- ata_port_freeze(ap);
- }
- } else {
- if (in_wq) {
- spin_lock_irqsave(ap->lock, flags);
- ap->ops->irq_on(ap);
- ata_qc_complete(qc);
- spin_unlock_irqrestore(ap->lock, flags);
- } else
- ata_qc_complete(qc);
- }
-}
-
-/**
- * ata_hsm_move - move the HSM to the next state.
- * @ap: the target ata_port
- * @qc: qc on going
- * @status: current device status
- * @in_wq: 1 if called from workqueue, 0 otherwise
- *
- * RETURNS:
- * 1 when poll next status needed, 0 otherwise.
- */
-int ata_hsm_move(struct ata_port *ap, struct ata_queued_cmd *qc,
- u8 status, int in_wq)
-{
- unsigned long flags = 0;
- int poll_next;
-
- WARN_ON((qc->flags & ATA_QCFLAG_ACTIVE) == 0);
-
- /* Make sure ata_qc_issue_prot() does not throw things
- * like DMA polling into the workqueue. Notice that
- * in_wq is not equivalent to (qc->tf.flags & ATA_TFLAG_POLLING).
- */
- WARN_ON(in_wq != ata_hsm_ok_in_wq(ap, qc));
-
-fsm_start:
- DPRINTK("ata%u: protocol %d task_state %d (dev_stat 0x%X)\n",
- ap->print_id, qc->tf.protocol, ap->hsm_task_state, status);
-
- switch (ap->hsm_task_state) {
- case HSM_ST_FIRST:
- /* Send first data block or PACKET CDB */
-
- /* If polling, we will stay in the work queue after
- * sending the data. Otherwise, interrupt handler
- * takes over after sending the data.
- */
- poll_next = (qc->tf.flags & ATA_TFLAG_POLLING);
-
- /* check device status */
- if (unlikely((status & ATA_DRQ) == 0)) {
- /* handle BSY=0, DRQ=0 as error */
- if (likely(status & (ATA_ERR | ATA_DF)))
- /* device stops HSM for abort/error */
- qc->err_mask |= AC_ERR_DEV;
- else
- /* HSM violation. Let EH handle this */
- qc->err_mask |= AC_ERR_HSM;
-
- ap->hsm_task_state = HSM_ST_ERR;
- goto fsm_start;
- }
-
- /* Device should not ask for data transfer (DRQ=1)
- * when it finds something wrong.
- * We ignore DRQ here and stop the HSM by
- * changing hsm_task_state to HSM_ST_ERR and
- * let the EH abort the command or reset the device.
- */
- if (unlikely(status & (ATA_ERR | ATA_DF))) {
- /* Some ATAPI tape drives forget to clear the ERR bit
- * when doing the next command (mostly request sense).
- * We ignore ERR here to workaround and proceed sending
- * the CDB.
- */
- if (!(qc->dev->horkage & ATA_HORKAGE_STUCK_ERR)) {
- ata_port_printk(ap, KERN_WARNING,
- "DRQ=1 with device error, "
- "dev_stat 0x%X\n", status);
- qc->err_mask |= AC_ERR_HSM;
- ap->hsm_task_state = HSM_ST_ERR;
- goto fsm_start;
- }
- }
-
- /* Send the CDB (atapi) or the first data block (ata pio out).
- * During the state transition, interrupt handler shouldn't
- * be invoked before the data transfer is complete and
- * hsm_task_state is changed. Hence, the following locking.
- */
- if (in_wq)
- spin_lock_irqsave(ap->lock, flags);
-
- if (qc->tf.protocol == ATA_PROT_PIO) {
- /* PIO data out protocol.
- * send first data block.
- */
-
- /* ata_pio_sectors() might change the state
- * to HSM_ST_LAST. so, the state is changed here
- * before ata_pio_sectors().
- */
- ap->hsm_task_state = HSM_ST;
- ata_pio_sectors(qc);
- } else
- /* send CDB */
- atapi_send_cdb(ap, qc);
-
- if (in_wq)
- spin_unlock_irqrestore(ap->lock, flags);
-
- /* if polling, ata_pio_task() handles the rest.
- * otherwise, interrupt handler takes over from here.
- */
- break;
-
- case HSM_ST:
- /* complete command or read/write the data register */
- if (qc->tf.protocol == ATAPI_PROT_PIO) {
- /* ATAPI PIO protocol */
- if ((status & ATA_DRQ) == 0) {
- /* No more data to transfer or device error.
- * Device error will be tagged in HSM_ST_LAST.
- */
- ap->hsm_task_state = HSM_ST_LAST;
- goto fsm_start;
- }
-
- /* Device should not ask for data transfer (DRQ=1)
- * when it finds something wrong.
- * We ignore DRQ here and stop the HSM by
- * changing hsm_task_state to HSM_ST_ERR and
- * let the EH abort the command or reset the device.
- */
- if (unlikely(status & (ATA_ERR | ATA_DF))) {
- ata_port_printk(ap, KERN_WARNING, "DRQ=1 with "
- "device error, dev_stat 0x%X\n",
- status);
- qc->err_mask |= AC_ERR_HSM;
- ap->hsm_task_state = HSM_ST_ERR;
- goto fsm_start;
- }
-
- atapi_pio_bytes(qc);
-
- if (unlikely(ap->hsm_task_state == HSM_ST_ERR))
- /* bad ireason reported by device */
- goto fsm_start;
-
- } else {
- /* ATA PIO protocol */
- if (unlikely((status & ATA_DRQ) == 0)) {
- /* handle BSY=0, DRQ=0 as error */
- if (likely(status & (ATA_ERR | ATA_DF)))
- /* device stops HSM for abort/error */
- qc->err_mask |= AC_ERR_DEV;
- else
- /* HSM violation. Let EH handle this.
- * Phantom devices also trigger this
- * condition. Mark hint.
- */
- qc->err_mask |= AC_ERR_HSM |
- AC_ERR_NODEV_HINT;
-
- ap->hsm_task_state = HSM_ST_ERR;
- goto fsm_start;
- }
-
- /* For PIO reads, some devices may ask for
- * data transfer (DRQ=1) alone with ERR=1.
- * We respect DRQ here and transfer one
- * block of junk data before changing the
- * hsm_task_state to HSM_ST_ERR.
- *
- * For PIO writes, ERR=1 DRQ=1 doesn't make
- * sense since the data block has been
- * transferred to the device.
- */
- if (unlikely(status & (ATA_ERR | ATA_DF))) {
- /* data might be corrputed */
- qc->err_mask |= AC_ERR_DEV;
-
- if (!(qc->tf.flags & ATA_TFLAG_WRITE)) {
- ata_pio_sectors(qc);
- status = ata_wait_idle(ap);
- }
-
- if (status & (ATA_BUSY | ATA_DRQ))
- qc->err_mask |= AC_ERR_HSM;
-
- /* ata_pio_sectors() might change the
- * state to HSM_ST_LAST. so, the state
- * is changed after ata_pio_sectors().
- */
- ap->hsm_task_state = HSM_ST_ERR;
- goto fsm_start;
- }
+ * spin_lock_irqsave(host lock)
+ *
+ * RETURNS: 0 when ATAPI DMA can be used
+ * nonzero otherwise
+ */
+int ata_check_atapi_dma(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
- ata_pio_sectors(qc);
+ /* Don't allow DMA if it isn't multiple of 16 bytes. Quite a
+ * few ATAPI devices choke on such DMA requests.
+ */
+ if (unlikely(qc->nbytes & 15))
+ return 1;
- if (ap->hsm_task_state == HSM_ST_LAST &&
- (!(qc->tf.flags & ATA_TFLAG_WRITE))) {
- /* all data read */
- status = ata_wait_idle(ap);
- goto fsm_start;
- }
- }
+ if (ap->ops->check_atapi_dma)
+ return ap->ops->check_atapi_dma(qc);
- poll_next = 1;
- break;
+ return 0;
+}
- case HSM_ST_LAST:
- if (unlikely(!ata_ok(status))) {
- qc->err_mask |= __ac_err_mask(status);
- ap->hsm_task_state = HSM_ST_ERR;
- goto fsm_start;
- }
+/**
+ * ata_std_qc_defer - Check whether a qc needs to be deferred
+ * @qc: ATA command in question
+ *
+ * Non-NCQ commands cannot run with any other command, NCQ or
+ * not. As upper layer only knows the queue depth, we are
+ * responsible for maintaining exclusion. This function checks
+ * whether a new command @qc can be issued.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ *
+ * RETURNS:
+ * ATA_DEFER_* if deferring is needed, 0 otherwise.
+ */
+int ata_std_qc_defer(struct ata_queued_cmd *qc)
+{
+ struct ata_link *link = qc->dev->link;
- /* no more data to transfer */
- DPRINTK("ata%u: dev %u command complete, drv_stat 0x%x\n",
- ap->print_id, qc->dev->devno, status);
+ if (qc->tf.protocol == ATA_PROT_NCQ) {
+ if (!ata_tag_valid(link->active_tag))
+ return 0;
+ } else {
+ if (!ata_tag_valid(link->active_tag) && !link->sactive)
+ return 0;
+ }
- WARN_ON(qc->err_mask);
+ return ATA_DEFER_LINK;
+}
- ap->hsm_task_state = HSM_ST_IDLE;
+void ata_noop_qc_prep(struct ata_queued_cmd *qc) { }
- /* complete taskfile transaction */
- ata_hsm_qc_complete(qc, in_wq);
+/**
+ * ata_sg_init - Associate command with scatter-gather table.
+ * @qc: Command to be associated
+ * @sg: Scatter-gather table.
+ * @n_elem: Number of elements in s/g table.
+ *
+ * Initialize the data-related elements of queued_cmd @qc
+ * to point to a scatter-gather table @sg, containing @n_elem
+ * elements.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */
+void ata_sg_init(struct ata_queued_cmd *qc, struct scatterlist *sg,
+ unsigned int n_elem)
+{
+ qc->sg = sg;
+ qc->n_elem = n_elem;
+ qc->cursg = qc->sg;
+}
- poll_next = 0;
- break;
+/**
+ * ata_sg_setup - DMA-map the scatter-gather table associated with a command.
+ * @qc: Command with scatter-gather table to be mapped.
+ *
+ * DMA-map the scatter-gather table associated with queued_cmd @qc.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ *
+ * RETURNS:
+ * Zero on success, negative on error.
+ *
+ */
+static int ata_sg_setup(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ unsigned int n_elem;
- case HSM_ST_ERR:
- /* make sure qc->err_mask is available to
- * know what's wrong and recover
- */
- WARN_ON(qc->err_mask == 0);
+ VPRINTK("ENTER, ata%u\n", ap->print_id);
- ap->hsm_task_state = HSM_ST_IDLE;
+ n_elem = dma_map_sg(ap->dev, qc->sg, qc->n_elem, qc->dma_dir);
+ if (n_elem < 1)
+ return -1;
- /* complete taskfile transaction */
- ata_hsm_qc_complete(qc, in_wq);
+ DPRINTK("%d sg elements mapped\n", n_elem);
- poll_next = 0;
- break;
- default:
- poll_next = 0;
- BUG();
- }
+ qc->n_elem = n_elem;
+ qc->flags |= ATA_QCFLAG_DMAMAP;
- return poll_next;
+ return 0;
}
-static void ata_pio_task(struct work_struct *work)
+/**
+ * swap_buf_le16 - swap halves of 16-bit words in place
+ * @buf: Buffer to swap
+ * @buf_words: Number of 16-bit words in buffer.
+ *
+ * Swap halves of 16-bit words if needed to convert from
+ * little-endian byte order to native cpu byte order, or
+ * vice-versa.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+void swap_buf_le16(u16 *buf, unsigned int buf_words)
{
- struct ata_port *ap =
- container_of(work, struct ata_port, port_task.work);
- struct ata_queued_cmd *qc = ap->port_task_data;
- u8 status;
- int poll_next;
-
-fsm_start:
- WARN_ON(ap->hsm_task_state == HSM_ST_IDLE);
-
- /*
- * This is purely heuristic. This is a fast path.
- * Sometimes when we enter, BSY will be cleared in
- * a chk-status or two. If not, the drive is probably seeking
- * or something. Snooze for a couple msecs, then
- * chk-status again. If still busy, queue delayed work.
- */
- status = ata_busy_wait(ap, ATA_BUSY, 5);
- if (status & ATA_BUSY) {
- msleep(2);
- status = ata_busy_wait(ap, ATA_BUSY, 10);
- if (status & ATA_BUSY) {
- ata_pio_queue_task(ap, qc, ATA_SHORT_PAUSE);
- return;
- }
- }
-
- /* move the HSM */
- poll_next = ata_hsm_move(ap, qc, status, 1);
+#ifdef __BIG_ENDIAN
+ unsigned int i;
- /* another command or interrupt handler
- * may be running at this point.
- */
- if (poll_next)
- goto fsm_start;
+ for (i = 0; i < buf_words; i++)
+ buf[i] = le16_to_cpu(buf[i]);
+#endif /* __BIG_ENDIAN */
}
/**
ata_qc_complete(qc);
}
-/**
- * ata_qc_issue_prot - issue taskfile to device in proto-dependent manner
- * @qc: command to issue to device
- *
- * Using various libata functions and hooks, this function
- * starts an ATA command. ATA commands are grouped into
- * classes called "protocols", and issuing each type of protocol
- * is slightly different.
- *
- * May be used as the qc_issue() entry in ata_port_operations.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- *
- * RETURNS:
- * Zero on success, AC_ERR_* mask on failure
- */
-
-unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
-
- /* Use polling pio if the LLD doesn't handle
- * interrupt driven pio and atapi CDB interrupt.
- */
- if (ap->flags & ATA_FLAG_PIO_POLLING) {
- switch (qc->tf.protocol) {
- case ATA_PROT_PIO:
- case ATA_PROT_NODATA:
- case ATAPI_PROT_PIO:
- case ATAPI_PROT_NODATA:
- qc->tf.flags |= ATA_TFLAG_POLLING;
- break;
- case ATAPI_PROT_DMA:
- if (qc->dev->flags & ATA_DFLAG_CDB_INTR)
- /* see ata_dma_blacklisted() */
- BUG();
- break;
- default:
- break;
- }
- }
-
- /* select the device */
- ata_dev_select(ap, qc->dev->devno, 1, 0);
-
- /* start the command */
- switch (qc->tf.protocol) {
- case ATA_PROT_NODATA:
- if (qc->tf.flags & ATA_TFLAG_POLLING)
- ata_qc_set_polling(qc);
-
- ata_tf_to_host(ap, &qc->tf);
- ap->hsm_task_state = HSM_ST_LAST;
-
- if (qc->tf.flags & ATA_TFLAG_POLLING)
- ata_pio_queue_task(ap, qc, 0);
-
- break;
-
- case ATA_PROT_DMA:
- WARN_ON(qc->tf.flags & ATA_TFLAG_POLLING);
-
- ap->ops->tf_load(ap, &qc->tf); /* load tf registers */
- ap->ops->bmdma_setup(qc); /* set up bmdma */
- ap->ops->bmdma_start(qc); /* initiate bmdma */
- ap->hsm_task_state = HSM_ST_LAST;
- break;
-
- case ATA_PROT_PIO:
- if (qc->tf.flags & ATA_TFLAG_POLLING)
- ata_qc_set_polling(qc);
-
- ata_tf_to_host(ap, &qc->tf);
-
- if (qc->tf.flags & ATA_TFLAG_WRITE) {
- /* PIO data out protocol */
- ap->hsm_task_state = HSM_ST_FIRST;
- ata_pio_queue_task(ap, qc, 0);
-
- /* always send first data block using
- * the ata_pio_task() codepath.
- */
- } else {
- /* PIO data in protocol */
- ap->hsm_task_state = HSM_ST;
-
- if (qc->tf.flags & ATA_TFLAG_POLLING)
- ata_pio_queue_task(ap, qc, 0);
-
- /* if polling, ata_pio_task() handles the rest.
- * otherwise, interrupt handler takes over from here.
- */
- }
-
- break;
-
- case ATAPI_PROT_PIO:
- case ATAPI_PROT_NODATA:
- if (qc->tf.flags & ATA_TFLAG_POLLING)
- ata_qc_set_polling(qc);
-
- ata_tf_to_host(ap, &qc->tf);
-
- ap->hsm_task_state = HSM_ST_FIRST;
-
- /* send cdb by polling if no cdb interrupt */
- if ((!(qc->dev->flags & ATA_DFLAG_CDB_INTR)) ||
- (qc->tf.flags & ATA_TFLAG_POLLING))
- ata_pio_queue_task(ap, qc, 0);
- break;
-
- case ATAPI_PROT_DMA:
- WARN_ON(qc->tf.flags & ATA_TFLAG_POLLING);
-
- ap->ops->tf_load(ap, &qc->tf); /* load tf registers */
- ap->ops->bmdma_setup(qc); /* set up bmdma */
- ap->hsm_task_state = HSM_ST_FIRST;
-
- /* send cdb by polling if no cdb interrupt */
- if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
- ata_pio_queue_task(ap, qc, 0);
- break;
-
- default:
- WARN_ON(1);
- return AC_ERR_SYSTEM;
- }
-
- return 0;
-}
-
-/**
- * ata_host_intr - Handle host interrupt for given (port, task)
- * @ap: Port on which interrupt arrived (possibly...)
- * @qc: Taskfile currently active in engine
- *
- * Handle host interrupt for given queued command. Currently,
- * only DMA interrupts are handled. All other commands are
- * handled via polling with interrupts disabled (nIEN bit).
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- *
- * RETURNS:
- * One if interrupt was handled, zero if not (shared irq).
- */
-
-inline unsigned int ata_host_intr(struct ata_port *ap,
- struct ata_queued_cmd *qc)
-{
- struct ata_eh_info *ehi = &ap->link.eh_info;
- u8 status, host_stat = 0;
-
- VPRINTK("ata%u: protocol %d task_state %d\n",
- ap->print_id, qc->tf.protocol, ap->hsm_task_state);
-
- /* Check whether we are expecting interrupt in this state */
- switch (ap->hsm_task_state) {
- case HSM_ST_FIRST:
- /* Some pre-ATAPI-4 devices assert INTRQ
- * at this state when ready to receive CDB.
- */
-
- /* Check the ATA_DFLAG_CDB_INTR flag is enough here.
- * The flag was turned on only for atapi devices. No
- * need to check ata_is_atapi(qc->tf.protocol) again.
- */
- if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
- goto idle_irq;
- break;
- case HSM_ST_LAST:
- if (qc->tf.protocol == ATA_PROT_DMA ||
- qc->tf.protocol == ATAPI_PROT_DMA) {
- /* check status of DMA engine */
- host_stat = ap->ops->bmdma_status(ap);
- VPRINTK("ata%u: host_stat 0x%X\n",
- ap->print_id, host_stat);
-
- /* if it's not our irq... */
- if (!(host_stat & ATA_DMA_INTR))
- goto idle_irq;
-
- /* before we do anything else, clear DMA-Start bit */
- ap->ops->bmdma_stop(qc);
-
- if (unlikely(host_stat & ATA_DMA_ERR)) {
- /* error when transfering data to/from memory */
- qc->err_mask |= AC_ERR_HOST_BUS;
- ap->hsm_task_state = HSM_ST_ERR;
- }
- }
- break;
- case HSM_ST:
- break;
- default:
- goto idle_irq;
- }
-
- /* check altstatus */
- status = ata_altstatus(ap);
- if (status & ATA_BUSY)
- goto idle_irq;
-
- /* check main status, clearing INTRQ */
- status = ata_chk_status(ap);
- if (unlikely(status & ATA_BUSY))
- goto idle_irq;
-
- /* ack bmdma irq events */
- ap->ops->irq_clear(ap);
-
- ata_hsm_move(ap, qc, status, 0);
-
- if (unlikely(qc->err_mask) && (qc->tf.protocol == ATA_PROT_DMA ||
- qc->tf.protocol == ATAPI_PROT_DMA))
- ata_ehi_push_desc(ehi, "BMDMA stat 0x%x", host_stat);
-
- return 1; /* irq handled */
-
-idle_irq:
- ap->stats.idle_irq++;
-
-#ifdef ATA_IRQ_TRAP
- if ((ap->stats.idle_irq % 1000) == 0) {
- ata_chk_status(ap);
- ap->ops->irq_clear(ap);
- ata_port_printk(ap, KERN_WARNING, "irq trap\n");
- return 1;
- }
-#endif
- return 0; /* irq not handled */
-}
-
-/**
- * ata_interrupt - Default ATA host interrupt handler
- * @irq: irq line (unused)
- * @dev_instance: pointer to our ata_host information structure
- *
- * Default interrupt handler for PCI IDE devices. Calls
- * ata_host_intr() for each port that is not disabled.
- *
- * LOCKING:
- * Obtains host lock during operation.
- *
- * RETURNS:
- * IRQ_NONE or IRQ_HANDLED.
- */
-
-irqreturn_t ata_interrupt(int irq, void *dev_instance)
-{
- struct ata_host *host = dev_instance;
- unsigned int i;
- unsigned int handled = 0;
- unsigned long flags;
-
- /* TODO: make _irqsave conditional on x86 PCI IDE legacy mode */
- spin_lock_irqsave(&host->lock, flags);
-
- for (i = 0; i < host->n_ports; i++) {
- struct ata_port *ap;
-
- ap = host->ports[i];
- if (ap &&
- !(ap->flags & ATA_FLAG_DISABLED)) {
- struct ata_queued_cmd *qc;
-
- qc = ata_qc_from_tag(ap, ap->link.active_tag);
- if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING)) &&
- (qc->flags & ATA_QCFLAG_ACTIVE))
- handled |= ata_host_intr(ap, qc);
- }
- }
-
- spin_unlock_irqrestore(&host->lock, flags);
-
- return IRQ_RETVAL(handled);
-}
-
/**
* sata_scr_valid - test whether SCRs are accessible
* @link: ATA link to test SCR accessibility for
ata_acpi_dissociate(host);
}
-/**
- * ata_std_ports - initialize ioaddr with standard port offsets.
- * @ioaddr: IO address structure to be initialized
- *
- * Utility function which initializes data_addr, error_addr,
- * feature_addr, nsect_addr, lbal_addr, lbam_addr, lbah_addr,
- * device_addr, status_addr, and command_addr to standard offsets
- * relative to cmd_addr.
- *
- * Does not set ctl_addr, altstatus_addr, bmdma_addr, or scr_addr.
- */
-
-void ata_std_ports(struct ata_ioports *ioaddr)
-{
- ioaddr->data_addr = ioaddr->cmd_addr + ATA_REG_DATA;
- ioaddr->error_addr = ioaddr->cmd_addr + ATA_REG_ERR;
- ioaddr->feature_addr = ioaddr->cmd_addr + ATA_REG_FEATURE;
- ioaddr->nsect_addr = ioaddr->cmd_addr + ATA_REG_NSECT;
- ioaddr->lbal_addr = ioaddr->cmd_addr + ATA_REG_LBAL;
- ioaddr->lbam_addr = ioaddr->cmd_addr + ATA_REG_LBAM;
- ioaddr->lbah_addr = ioaddr->cmd_addr + ATA_REG_LBAH;
- ioaddr->device_addr = ioaddr->cmd_addr + ATA_REG_DEVICE;
- ioaddr->status_addr = ioaddr->cmd_addr + ATA_REG_STATUS;
- ioaddr->command_addr = ioaddr->cmd_addr + ATA_REG_CMD;
-}
-
-
#ifdef CONFIG_PCI
/**
EXPORT_SYMBOL_GPL(ata_base_port_ops);
EXPORT_SYMBOL_GPL(sata_port_ops);
EXPORT_SYMBOL_GPL(sata_pmp_port_ops);
-EXPORT_SYMBOL_GPL(ata_sff_port_ops);
-EXPORT_SYMBOL_GPL(ata_bmdma_port_ops);
EXPORT_SYMBOL_GPL(ata_dummy_port_ops);
EXPORT_SYMBOL_GPL(ata_dummy_port_info);
EXPORT_SYMBOL_GPL(ata_std_bios_param);
-EXPORT_SYMBOL_GPL(ata_std_ports);
EXPORT_SYMBOL_GPL(ata_host_init);
EXPORT_SYMBOL_GPL(ata_host_alloc);
EXPORT_SYMBOL_GPL(ata_host_alloc_pinfo);
EXPORT_SYMBOL_GPL(ata_host_activate);
EXPORT_SYMBOL_GPL(ata_host_detach);
EXPORT_SYMBOL_GPL(ata_sg_init);
-EXPORT_SYMBOL_GPL(ata_hsm_move);
EXPORT_SYMBOL_GPL(ata_qc_complete);
EXPORT_SYMBOL_GPL(ata_qc_complete_multiple);
-EXPORT_SYMBOL_GPL(ata_qc_issue_prot);
-EXPORT_SYMBOL_GPL(ata_tf_load);
-EXPORT_SYMBOL_GPL(ata_tf_read);
EXPORT_SYMBOL_GPL(ata_noop_dev_select);
-EXPORT_SYMBOL_GPL(ata_std_dev_select);
EXPORT_SYMBOL_GPL(sata_print_link_status);
EXPORT_SYMBOL_GPL(atapi_cmd_type);
EXPORT_SYMBOL_GPL(ata_tf_to_fis);
EXPORT_SYMBOL_GPL(ata_xfer_mode2shift);
EXPORT_SYMBOL_GPL(ata_mode_string);
EXPORT_SYMBOL_GPL(ata_id_xfermask);
-EXPORT_SYMBOL_GPL(ata_check_status);
-EXPORT_SYMBOL_GPL(ata_altstatus);
-EXPORT_SYMBOL_GPL(ata_exec_command);
EXPORT_SYMBOL_GPL(ata_port_start);
-EXPORT_SYMBOL_GPL(ata_sff_port_start);
-EXPORT_SYMBOL_GPL(ata_interrupt);
EXPORT_SYMBOL_GPL(ata_do_set_mode);
-EXPORT_SYMBOL_GPL(ata_data_xfer);
-EXPORT_SYMBOL_GPL(ata_data_xfer_noirq);
EXPORT_SYMBOL_GPL(ata_std_qc_defer);
-EXPORT_SYMBOL_GPL(ata_qc_prep);
-EXPORT_SYMBOL_GPL(ata_dumb_qc_prep);
EXPORT_SYMBOL_GPL(ata_noop_qc_prep);
-EXPORT_SYMBOL_GPL(ata_bmdma_setup);
-EXPORT_SYMBOL_GPL(ata_bmdma_start);
-EXPORT_SYMBOL_GPL(ata_bmdma_irq_clear);
EXPORT_SYMBOL_GPL(ata_noop_irq_clear);
-EXPORT_SYMBOL_GPL(ata_bmdma_status);
-EXPORT_SYMBOL_GPL(ata_bmdma_stop);
-EXPORT_SYMBOL_GPL(ata_bmdma_freeze);
-EXPORT_SYMBOL_GPL(ata_bmdma_thaw);
-EXPORT_SYMBOL_GPL(ata_bmdma_error_handler);
-EXPORT_SYMBOL_GPL(ata_bmdma_post_internal_cmd);
EXPORT_SYMBOL_GPL(ata_port_probe);
EXPORT_SYMBOL_GPL(ata_dev_disable);
EXPORT_SYMBOL_GPL(sata_set_spd);
EXPORT_SYMBOL_GPL(sata_link_debounce);
EXPORT_SYMBOL_GPL(sata_link_resume);
-EXPORT_SYMBOL_GPL(ata_bus_reset);
-EXPORT_SYMBOL_GPL(ata_std_prereset);
-EXPORT_SYMBOL_GPL(ata_std_softreset);
EXPORT_SYMBOL_GPL(sata_link_hardreset);
-EXPORT_SYMBOL_GPL(sata_std_hardreset);
-EXPORT_SYMBOL_GPL(ata_std_postreset);
EXPORT_SYMBOL_GPL(ata_dev_classify);
EXPORT_SYMBOL_GPL(ata_dev_pair);
EXPORT_SYMBOL_GPL(ata_port_disable);
EXPORT_SYMBOL_GPL(ata_ratelimit);
EXPORT_SYMBOL_GPL(ata_wait_register);
-EXPORT_SYMBOL_GPL(ata_busy_sleep);
-EXPORT_SYMBOL_GPL(ata_wait_after_reset);
-EXPORT_SYMBOL_GPL(ata_wait_ready);
EXPORT_SYMBOL_GPL(ata_scsi_ioctl);
EXPORT_SYMBOL_GPL(ata_scsi_queuecmd);
EXPORT_SYMBOL_GPL(ata_scsi_slave_config);
EXPORT_SYMBOL_GPL(ata_scsi_slave_destroy);
EXPORT_SYMBOL_GPL(ata_scsi_change_queue_depth);
-EXPORT_SYMBOL_GPL(ata_host_intr);
EXPORT_SYMBOL_GPL(sata_scr_valid);
EXPORT_SYMBOL_GPL(sata_scr_read);
EXPORT_SYMBOL_GPL(sata_scr_write);
#ifdef CONFIG_PCI
EXPORT_SYMBOL_GPL(pci_test_config_bits);
-EXPORT_SYMBOL_GPL(ata_pci_init_sff_host);
-EXPORT_SYMBOL_GPL(ata_pci_init_bmdma);
-EXPORT_SYMBOL_GPL(ata_pci_prepare_sff_host);
-EXPORT_SYMBOL_GPL(ata_pci_activate_sff_host);
-EXPORT_SYMBOL_GPL(ata_pci_init_one);
EXPORT_SYMBOL_GPL(ata_pci_remove_one);
#ifdef CONFIG_PM
EXPORT_SYMBOL_GPL(ata_pci_device_do_suspend);
EXPORT_SYMBOL_GPL(ata_pci_device_suspend);
EXPORT_SYMBOL_GPL(ata_pci_device_resume);
#endif /* CONFIG_PM */
-EXPORT_SYMBOL_GPL(ata_pci_default_filter);
-EXPORT_SYMBOL_GPL(ata_pci_clear_simplex);
#endif /* CONFIG_PCI */
EXPORT_SYMBOL_GPL(sata_pmp_qc_defer_cmd_switch);
EXPORT_SYMBOL_GPL(ata_eh_qc_retry);
EXPORT_SYMBOL_GPL(ata_do_eh);
EXPORT_SYMBOL_GPL(ata_std_error_handler);
-EXPORT_SYMBOL_GPL(ata_irq_on);
-EXPORT_SYMBOL_GPL(ata_dev_try_classify);
EXPORT_SYMBOL_GPL(ata_cable_40wire);
EXPORT_SYMBOL_GPL(ata_cable_80wire);
#include <linux/kernel.h>
#include <linux/pci.h>
#include <linux/libata.h>
+#include <linux/highmem.h>
#include "libata.h"
+const struct ata_port_operations ata_sff_port_ops = {
+ .inherits = &ata_base_port_ops,
+
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .softreset = ata_std_softreset,
+ .error_handler = ata_bmdma_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .dev_select = ata_std_dev_select,
+ .check_status = ata_check_status,
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .exec_command = ata_exec_command,
+ .data_xfer = ata_data_xfer,
+ .irq_on = ata_irq_on,
+
+ .port_start = ata_sff_port_start,
+};
+
+const struct ata_port_operations ata_bmdma_port_ops = {
+ .inherits = &ata_sff_port_ops,
+
+ .mode_filter = ata_pci_default_filter,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .irq_clear = ata_bmdma_irq_clear,
+};
+
+/**
+ * ata_fill_sg - Fill PCI IDE PRD table
+ * @qc: Metadata associated with taskfile to be transferred
+ *
+ * Fill PCI IDE PRD (scatter-gather) table with segments
+ * associated with the current disk command.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ *
+ */
+static void ata_fill_sg(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct scatterlist *sg;
+ unsigned int si, pi;
+
+ pi = 0;
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
+ u32 addr, offset;
+ u32 sg_len, len;
+
+ /* determine if physical DMA addr spans 64K boundary.
+ * Note h/w doesn't support 64-bit, so we unconditionally
+ * truncate dma_addr_t to u32.
+ */
+ addr = (u32) sg_dma_address(sg);
+ sg_len = sg_dma_len(sg);
+
+ while (sg_len) {
+ offset = addr & 0xffff;
+ len = sg_len;
+ if ((offset + sg_len) > 0x10000)
+ len = 0x10000 - offset;
+
+ ap->prd[pi].addr = cpu_to_le32(addr);
+ ap->prd[pi].flags_len = cpu_to_le32(len & 0xffff);
+ VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", pi, addr, len);
+
+ pi++;
+ sg_len -= len;
+ addr += len;
+ }
+ }
+
+ ap->prd[pi - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
+}
+
+/**
+ * ata_fill_sg_dumb - Fill PCI IDE PRD table
+ * @qc: Metadata associated with taskfile to be transferred
+ *
+ * Fill PCI IDE PRD (scatter-gather) table with segments
+ * associated with the current disk command. Perform the fill
+ * so that we avoid writing any length 64K records for
+ * controllers that don't follow the spec.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ *
+ */
+static void ata_fill_sg_dumb(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct scatterlist *sg;
+ unsigned int si, pi;
+
+ pi = 0;
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
+ u32 addr, offset;
+ u32 sg_len, len, blen;
+
+ /* determine if physical DMA addr spans 64K boundary.
+ * Note h/w doesn't support 64-bit, so we unconditionally
+ * truncate dma_addr_t to u32.
+ */
+ addr = (u32) sg_dma_address(sg);
+ sg_len = sg_dma_len(sg);
+
+ while (sg_len) {
+ offset = addr & 0xffff;
+ len = sg_len;
+ if ((offset + sg_len) > 0x10000)
+ len = 0x10000 - offset;
+
+ blen = len & 0xffff;
+ ap->prd[pi].addr = cpu_to_le32(addr);
+ if (blen == 0) {
+ /* Some PATA chipsets like the CS5530 can't
+ cope with 0x0000 meaning 64K as the spec says */
+ ap->prd[pi].flags_len = cpu_to_le32(0x8000);
+ blen = 0x8000;
+ ap->prd[++pi].addr = cpu_to_le32(addr + 0x8000);
+ }
+ ap->prd[pi].flags_len = cpu_to_le32(blen);
+ VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", pi, addr, len);
+
+ pi++;
+ sg_len -= len;
+ addr += len;
+ }
+ }
+
+ ap->prd[pi - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
+}
+
+/**
+ * ata_qc_prep - Prepare taskfile for submission
+ * @qc: Metadata associated with taskfile to be prepared
+ *
+ * Prepare ATA taskfile for submission.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */
+void ata_qc_prep(struct ata_queued_cmd *qc)
+{
+ if (!(qc->flags & ATA_QCFLAG_DMAMAP))
+ return;
+
+ ata_fill_sg(qc);
+}
+
+/**
+ * ata_dumb_qc_prep - Prepare taskfile for submission
+ * @qc: Metadata associated with taskfile to be prepared
+ *
+ * Prepare ATA taskfile for submission.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */
+void ata_dumb_qc_prep(struct ata_queued_cmd *qc)
+{
+ if (!(qc->flags & ATA_QCFLAG_DMAMAP))
+ return;
+
+ ata_fill_sg_dumb(qc);
+}
+
/**
* ata_check_status - Read device status reg & clear interrupt
* @ap: port where the device is
* LOCKING:
* Inherited from caller.
*/
-u8 ata_altstatus(struct ata_port *ap)
+u8 ata_altstatus(struct ata_port *ap)
+{
+ if (ap->ops->check_altstatus)
+ return ap->ops->check_altstatus(ap);
+
+ return ioread8(ap->ioaddr.altstatus_addr);
+}
+
+/**
+ * ata_busy_sleep - sleep until BSY clears, or timeout
+ * @ap: port containing status register to be polled
+ * @tmout_pat: impatience timeout
+ * @tmout: overall timeout
+ *
+ * Sleep until ATA Status register bit BSY clears,
+ * or a timeout occurs.
+ *
+ * LOCKING:
+ * Kernel thread context (may sleep).
+ *
+ * RETURNS:
+ * 0 on success, -errno otherwise.
+ */
+int ata_busy_sleep(struct ata_port *ap,
+ unsigned long tmout_pat, unsigned long tmout)
+{
+ unsigned long timer_start, timeout;
+ u8 status;
+
+ status = ata_busy_wait(ap, ATA_BUSY, 300);
+ timer_start = jiffies;
+ timeout = timer_start + tmout_pat;
+ while (status != 0xff && (status & ATA_BUSY) &&
+ time_before(jiffies, timeout)) {
+ msleep(50);
+ status = ata_busy_wait(ap, ATA_BUSY, 3);
+ }
+
+ if (status != 0xff && (status & ATA_BUSY))
+ ata_port_printk(ap, KERN_WARNING,
+ "port is slow to respond, please be patient "
+ "(Status 0x%x)\n", status);
+
+ timeout = timer_start + tmout;
+ while (status != 0xff && (status & ATA_BUSY) &&
+ time_before(jiffies, timeout)) {
+ msleep(50);
+ status = ata_chk_status(ap);
+ }
+
+ if (status == 0xff)
+ return -ENODEV;
+
+ if (status & ATA_BUSY) {
+ ata_port_printk(ap, KERN_ERR, "port failed to respond "
+ "(%lu secs, Status 0x%x)\n",
+ tmout / HZ, status);
+ return -EBUSY;
+ }
+
+ return 0;
+}
+
+/**
+ * ata_wait_ready - sleep until BSY clears, or timeout
+ * @ap: port containing status register to be polled
+ * @deadline: deadline jiffies for the operation
+ *
+ * Sleep until ATA Status register bit BSY clears, or timeout
+ * occurs.
+ *
+ * LOCKING:
+ * Kernel thread context (may sleep).
+ *
+ * RETURNS:
+ * 0 on success, -errno otherwise.
+ */
+int ata_wait_ready(struct ata_port *ap, unsigned long deadline)
+{
+ unsigned long start = jiffies;
+ int warned = 0;
+
+ while (1) {
+ u8 status = ata_chk_status(ap);
+ unsigned long now = jiffies;
+
+ if (!(status & ATA_BUSY))
+ return 0;
+ if (!ata_link_online(&ap->link) && status == 0xff)
+ return -ENODEV;
+ if (time_after(now, deadline))
+ return -EBUSY;
+
+ if (!warned && time_after(now, start + 5 * HZ) &&
+ (deadline - now > 3 * HZ)) {
+ ata_port_printk(ap, KERN_WARNING,
+ "port is slow to respond, please be patient "
+ "(Status 0x%x)\n", status);
+ warned = 1;
+ }
+
+ msleep(50);
+ }
+}
+
+/**
+ * ata_std_dev_select - Select device 0/1 on ATA bus
+ * @ap: ATA channel to manipulate
+ * @device: ATA device (numbered from zero) to select
+ *
+ * Use the method defined in the ATA specification to
+ * make either device 0, or device 1, active on the
+ * ATA channel. Works with both PIO and MMIO.
+ *
+ * May be used as the dev_select() entry in ata_port_operations.
+ *
+ * LOCKING:
+ * caller.
+ */
+void ata_std_dev_select(struct ata_port *ap, unsigned int device)
+{
+ u8 tmp;
+
+ if (device == 0)
+ tmp = ATA_DEVICE_OBS;
+ else
+ tmp = ATA_DEVICE_OBS | ATA_DEV1;
+
+ iowrite8(tmp, ap->ioaddr.device_addr);
+ ata_pause(ap); /* needed; also flushes, for mmio */
+}
+
+/**
+ * ata_dev_select - Select device 0/1 on ATA bus
+ * @ap: ATA channel to manipulate
+ * @device: ATA device (numbered from zero) to select
+ * @wait: non-zero to wait for Status register BSY bit to clear
+ * @can_sleep: non-zero if context allows sleeping
+ *
+ * Use the method defined in the ATA specification to
+ * make either device 0, or device 1, active on the
+ * ATA channel.
+ *
+ * This is a high-level version of ata_std_dev_select(),
+ * which additionally provides the services of inserting
+ * the proper pauses and status polling, where needed.
+ *
+ * LOCKING:
+ * caller.
+ */
+void ata_dev_select(struct ata_port *ap, unsigned int device,
+ unsigned int wait, unsigned int can_sleep)
+{
+ if (ata_msg_probe(ap))
+ ata_port_printk(ap, KERN_INFO, "ata_dev_select: ENTER, "
+ "device %u, wait %u\n", device, wait);
+
+ if (wait)
+ ata_wait_idle(ap);
+
+ ap->ops->dev_select(ap, device);
+
+ if (wait) {
+ if (can_sleep && ap->link.device[device].class == ATA_DEV_ATAPI)
+ msleep(150);
+ ata_wait_idle(ap);
+ }
+}
+
+/**
+ * ata_irq_on - Enable interrupts on a port.
+ * @ap: Port on which interrupts are enabled.
+ *
+ * Enable interrupts on a legacy IDE device using MMIO or PIO,
+ * wait for idle, clear any pending interrupts.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+u8 ata_irq_on(struct ata_port *ap)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ u8 tmp;
+
+ ap->ctl &= ~ATA_NIEN;
+ ap->last_ctl = ap->ctl;
+
+ if (ioaddr->ctl_addr)
+ iowrite8(ap->ctl, ioaddr->ctl_addr);
+ tmp = ata_wait_idle(ap);
+
+ ap->ops->irq_clear(ap);
+
+ return tmp;
+}
+
+/**
+ * ata_bmdma_irq_clear - Clear PCI IDE BMDMA interrupt.
+ * @ap: Port associated with this ATA transaction.
+ *
+ * Clear interrupt and error flags in DMA status register.
+ *
+ * May be used as the irq_clear() entry in ata_port_operations.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */
+void ata_bmdma_irq_clear(struct ata_port *ap)
+{
+ void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+ if (!mmio)
+ return;
+
+ iowrite8(ioread8(mmio + ATA_DMA_STATUS), mmio + ATA_DMA_STATUS);
+}
+
+/**
+ * ata_tf_load - send taskfile registers to host controller
+ * @ap: Port to which output is sent
+ * @tf: ATA taskfile register set
+ *
+ * Outputs ATA taskfile to standard ATA host controller.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+void ata_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
+
+ if (tf->ctl != ap->last_ctl) {
+ if (ioaddr->ctl_addr)
+ iowrite8(tf->ctl, ioaddr->ctl_addr);
+ ap->last_ctl = tf->ctl;
+ ata_wait_idle(ap);
+ }
+
+ if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
+ WARN_ON(!ioaddr->ctl_addr);
+ iowrite8(tf->hob_feature, ioaddr->feature_addr);
+ iowrite8(tf->hob_nsect, ioaddr->nsect_addr);
+ iowrite8(tf->hob_lbal, ioaddr->lbal_addr);
+ iowrite8(tf->hob_lbam, ioaddr->lbam_addr);
+ iowrite8(tf->hob_lbah, ioaddr->lbah_addr);
+ VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n",
+ tf->hob_feature,
+ tf->hob_nsect,
+ tf->hob_lbal,
+ tf->hob_lbam,
+ tf->hob_lbah);
+ }
+
+ if (is_addr) {
+ iowrite8(tf->feature, ioaddr->feature_addr);
+ iowrite8(tf->nsect, ioaddr->nsect_addr);
+ iowrite8(tf->lbal, ioaddr->lbal_addr);
+ iowrite8(tf->lbam, ioaddr->lbam_addr);
+ iowrite8(tf->lbah, ioaddr->lbah_addr);
+ VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
+ tf->feature,
+ tf->nsect,
+ tf->lbal,
+ tf->lbam,
+ tf->lbah);
+ }
+
+ if (tf->flags & ATA_TFLAG_DEVICE) {
+ iowrite8(tf->device, ioaddr->device_addr);
+ VPRINTK("device 0x%X\n", tf->device);
+ }
+
+ ata_wait_idle(ap);
+}
+
+/**
+ * ata_tf_read - input device's ATA taskfile shadow registers
+ * @ap: Port from which input is read
+ * @tf: ATA taskfile register set for storing input
+ *
+ * Reads ATA taskfile registers for currently-selected device
+ * into @tf. Assumes the device has a fully SFF compliant task file
+ * layout and behaviour. If you device does not (eg has a different
+ * status method) then you will need to provide a replacement tf_read
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+
+ tf->command = ata_check_status(ap);
+ tf->feature = ioread8(ioaddr->error_addr);
+ tf->nsect = ioread8(ioaddr->nsect_addr);
+ tf->lbal = ioread8(ioaddr->lbal_addr);
+ tf->lbam = ioread8(ioaddr->lbam_addr);
+ tf->lbah = ioread8(ioaddr->lbah_addr);
+ tf->device = ioread8(ioaddr->device_addr);
+
+ if (tf->flags & ATA_TFLAG_LBA48) {
+ if (likely(ioaddr->ctl_addr)) {
+ iowrite8(tf->ctl | ATA_HOB, ioaddr->ctl_addr);
+ tf->hob_feature = ioread8(ioaddr->error_addr);
+ tf->hob_nsect = ioread8(ioaddr->nsect_addr);
+ tf->hob_lbal = ioread8(ioaddr->lbal_addr);
+ tf->hob_lbam = ioread8(ioaddr->lbam_addr);
+ tf->hob_lbah = ioread8(ioaddr->lbah_addr);
+ iowrite8(tf->ctl, ioaddr->ctl_addr);
+ ap->last_ctl = tf->ctl;
+ } else
+ WARN_ON(1);
+ }
+}
+
+/**
+ * ata_exec_command - issue ATA command to host controller
+ * @ap: port to which command is being issued
+ * @tf: ATA taskfile register set
+ *
+ * Issues ATA command, with proper synchronization with interrupt
+ * handler / other threads.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */
+void ata_exec_command(struct ata_port *ap, const struct ata_taskfile *tf)
+{
+ DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
+
+ iowrite8(tf->command, ap->ioaddr.command_addr);
+ ata_pause(ap);
+}
+
+/**
+ * ata_tf_to_host - issue ATA taskfile to host controller
+ * @ap: port to which command is being issued
+ * @tf: ATA taskfile register set
+ *
+ * Issues ATA taskfile register set to ATA host controller,
+ * with proper synchronization with interrupt handler and
+ * other threads.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */
+static inline void ata_tf_to_host(struct ata_port *ap,
+ const struct ata_taskfile *tf)
+{
+ ap->ops->tf_load(ap, tf);
+ ap->ops->exec_command(ap, tf);
+}
+
+/**
+ * ata_data_xfer - Transfer data by PIO
+ * @dev: device to target
+ * @buf: data buffer
+ * @buflen: buffer length
+ * @rw: read/write
+ *
+ * Transfer data from/to the device data register by PIO.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ *
+ * RETURNS:
+ * Bytes consumed.
+ */
+unsigned int ata_data_xfer(struct ata_device *dev, unsigned char *buf,
+ unsigned int buflen, int rw)
+{
+ struct ata_port *ap = dev->link->ap;
+ void __iomem *data_addr = ap->ioaddr.data_addr;
+ unsigned int words = buflen >> 1;
+
+ /* Transfer multiple of 2 bytes */
+ if (rw == READ)
+ ioread16_rep(data_addr, buf, words);
+ else
+ iowrite16_rep(data_addr, buf, words);
+
+ /* Transfer trailing 1 byte, if any. */
+ if (unlikely(buflen & 0x01)) {
+ __le16 align_buf[1] = { 0 };
+ unsigned char *trailing_buf = buf + buflen - 1;
+
+ if (rw == READ) {
+ align_buf[0] = cpu_to_le16(ioread16(data_addr));
+ memcpy(trailing_buf, align_buf, 1);
+ } else {
+ memcpy(align_buf, trailing_buf, 1);
+ iowrite16(le16_to_cpu(align_buf[0]), data_addr);
+ }
+ words++;
+ }
+
+ return words << 1;
+}
+
+/**
+ * ata_data_xfer_noirq - Transfer data by PIO
+ * @dev: device to target
+ * @buf: data buffer
+ * @buflen: buffer length
+ * @rw: read/write
+ *
+ * Transfer data from/to the device data register by PIO. Do the
+ * transfer with interrupts disabled.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ *
+ * RETURNS:
+ * Bytes consumed.
+ */
+unsigned int ata_data_xfer_noirq(struct ata_device *dev, unsigned char *buf,
+ unsigned int buflen, int rw)
+{
+ unsigned long flags;
+ unsigned int consumed;
+
+ local_irq_save(flags);
+ consumed = ata_data_xfer(dev, buf, buflen, rw);
+ local_irq_restore(flags);
+
+ return consumed;
+}
+
+/**
+ * ata_pio_sector - Transfer a sector of data.
+ * @qc: Command on going
+ *
+ * Transfer qc->sect_size bytes of data from/to the ATA device.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static void ata_pio_sector(struct ata_queued_cmd *qc)
+{
+ int do_write = (qc->tf.flags & ATA_TFLAG_WRITE);
+ struct ata_port *ap = qc->ap;
+ struct page *page;
+ unsigned int offset;
+ unsigned char *buf;
+
+ if (qc->curbytes == qc->nbytes - qc->sect_size)
+ ap->hsm_task_state = HSM_ST_LAST;
+
+ page = sg_page(qc->cursg);
+ offset = qc->cursg->offset + qc->cursg_ofs;
+
+ /* get the current page and offset */
+ page = nth_page(page, (offset >> PAGE_SHIFT));
+ offset %= PAGE_SIZE;
+
+ DPRINTK("data %s\n", qc->tf.flags & ATA_TFLAG_WRITE ? "write" : "read");
+
+ if (PageHighMem(page)) {
+ unsigned long flags;
+
+ /* FIXME: use a bounce buffer */
+ local_irq_save(flags);
+ buf = kmap_atomic(page, KM_IRQ0);
+
+ /* do the actual data transfer */
+ ap->ops->data_xfer(qc->dev, buf + offset, qc->sect_size, do_write);
+
+ kunmap_atomic(buf, KM_IRQ0);
+ local_irq_restore(flags);
+ } else {
+ buf = page_address(page);
+ ap->ops->data_xfer(qc->dev, buf + offset, qc->sect_size, do_write);
+ }
+
+ qc->curbytes += qc->sect_size;
+ qc->cursg_ofs += qc->sect_size;
+
+ if (qc->cursg_ofs == qc->cursg->length) {
+ qc->cursg = sg_next(qc->cursg);
+ qc->cursg_ofs = 0;
+ }
+}
+
+/**
+ * ata_pio_sectors - Transfer one or many sectors.
+ * @qc: Command on going
+ *
+ * Transfer one or many sectors of data from/to the
+ * ATA device for the DRQ request.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static void ata_pio_sectors(struct ata_queued_cmd *qc)
+{
+ if (is_multi_taskfile(&qc->tf)) {
+ /* READ/WRITE MULTIPLE */
+ unsigned int nsect;
+
+ WARN_ON(qc->dev->multi_count == 0);
+
+ nsect = min((qc->nbytes - qc->curbytes) / qc->sect_size,
+ qc->dev->multi_count);
+ while (nsect--)
+ ata_pio_sector(qc);
+ } else
+ ata_pio_sector(qc);
+
+ ata_altstatus(qc->ap); /* flush */
+}
+
+/**
+ * atapi_send_cdb - Write CDB bytes to hardware
+ * @ap: Port to which ATAPI device is attached.
+ * @qc: Taskfile currently active
+ *
+ * When device has indicated its readiness to accept
+ * a CDB, this function is called. Send the CDB.
+ *
+ * LOCKING:
+ * caller.
+ */
+static void atapi_send_cdb(struct ata_port *ap, struct ata_queued_cmd *qc)
+{
+ /* send SCSI cdb */
+ DPRINTK("send cdb\n");
+ WARN_ON(qc->dev->cdb_len < 12);
+
+ ap->ops->data_xfer(qc->dev, qc->cdb, qc->dev->cdb_len, 1);
+ ata_altstatus(ap); /* flush */
+
+ switch (qc->tf.protocol) {
+ case ATAPI_PROT_PIO:
+ ap->hsm_task_state = HSM_ST;
+ break;
+ case ATAPI_PROT_NODATA:
+ ap->hsm_task_state = HSM_ST_LAST;
+ break;
+ case ATAPI_PROT_DMA:
+ ap->hsm_task_state = HSM_ST_LAST;
+ /* initiate bmdma */
+ ap->ops->bmdma_start(qc);
+ break;
+ }
+}
+
+/**
+ * __atapi_pio_bytes - Transfer data from/to the ATAPI device.
+ * @qc: Command on going
+ * @bytes: number of bytes
+ *
+ * Transfer Transfer data from/to the ATAPI device.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ *
+ */
+static int __atapi_pio_bytes(struct ata_queued_cmd *qc, unsigned int bytes)
+{
+ int rw = (qc->tf.flags & ATA_TFLAG_WRITE) ? WRITE : READ;
+ struct ata_port *ap = qc->ap;
+ struct ata_device *dev = qc->dev;
+ struct ata_eh_info *ehi = &dev->link->eh_info;
+ struct scatterlist *sg;
+ struct page *page;
+ unsigned char *buf;
+ unsigned int offset, count, consumed;
+
+next_sg:
+ sg = qc->cursg;
+ if (unlikely(!sg)) {
+ ata_ehi_push_desc(ehi, "unexpected or too much trailing data "
+ "buf=%u cur=%u bytes=%u",
+ qc->nbytes, qc->curbytes, bytes);
+ return -1;
+ }
+
+ page = sg_page(sg);
+ offset = sg->offset + qc->cursg_ofs;
+
+ /* get the current page and offset */
+ page = nth_page(page, (offset >> PAGE_SHIFT));
+ offset %= PAGE_SIZE;
+
+ /* don't overrun current sg */
+ count = min(sg->length - qc->cursg_ofs, bytes);
+
+ /* don't cross page boundaries */
+ count = min(count, (unsigned int)PAGE_SIZE - offset);
+
+ DPRINTK("data %s\n", qc->tf.flags & ATA_TFLAG_WRITE ? "write" : "read");
+
+ if (PageHighMem(page)) {
+ unsigned long flags;
+
+ /* FIXME: use bounce buffer */
+ local_irq_save(flags);
+ buf = kmap_atomic(page, KM_IRQ0);
+
+ /* do the actual data transfer */
+ consumed = ap->ops->data_xfer(dev, buf + offset, count, rw);
+
+ kunmap_atomic(buf, KM_IRQ0);
+ local_irq_restore(flags);
+ } else {
+ buf = page_address(page);
+ consumed = ap->ops->data_xfer(dev, buf + offset, count, rw);
+ }
+
+ bytes -= min(bytes, consumed);
+ qc->curbytes += count;
+ qc->cursg_ofs += count;
+
+ if (qc->cursg_ofs == sg->length) {
+ qc->cursg = sg_next(qc->cursg);
+ qc->cursg_ofs = 0;
+ }
+
+ /* consumed can be larger than count only for the last transfer */
+ WARN_ON(qc->cursg && count != consumed);
+
+ if (bytes)
+ goto next_sg;
+ return 0;
+}
+
+/**
+ * atapi_pio_bytes - Transfer data from/to the ATAPI device.
+ * @qc: Command on going
+ *
+ * Transfer Transfer data from/to the ATAPI device.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static void atapi_pio_bytes(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct ata_device *dev = qc->dev;
+ struct ata_eh_info *ehi = &dev->link->eh_info;
+ unsigned int ireason, bc_lo, bc_hi, bytes;
+ int i_write, do_write = (qc->tf.flags & ATA_TFLAG_WRITE) ? 1 : 0;
+
+ /* Abuse qc->result_tf for temp storage of intermediate TF
+ * here to save some kernel stack usage.
+ * For normal completion, qc->result_tf is not relevant. For
+ * error, qc->result_tf is later overwritten by ata_qc_complete().
+ * So, the correctness of qc->result_tf is not affected.
+ */
+ ap->ops->tf_read(ap, &qc->result_tf);
+ ireason = qc->result_tf.nsect;
+ bc_lo = qc->result_tf.lbam;
+ bc_hi = qc->result_tf.lbah;
+ bytes = (bc_hi << 8) | bc_lo;
+
+ /* shall be cleared to zero, indicating xfer of data */
+ if (unlikely(ireason & (1 << 0)))
+ goto atapi_check;
+
+ /* make sure transfer direction matches expected */
+ i_write = ((ireason & (1 << 1)) == 0) ? 1 : 0;
+ if (unlikely(do_write != i_write))
+ goto atapi_check;
+
+ if (unlikely(!bytes))
+ goto atapi_check;
+
+ VPRINTK("ata%u: xfering %d bytes\n", ap->print_id, bytes);
+
+ if (unlikely(__atapi_pio_bytes(qc, bytes)))
+ goto err_out;
+ ata_altstatus(ap); /* flush */
+
+ return;
+
+ atapi_check:
+ ata_ehi_push_desc(ehi, "ATAPI check failed (ireason=0x%x bytes=%u)",
+ ireason, bytes);
+ err_out:
+ qc->err_mask |= AC_ERR_HSM;
+ ap->hsm_task_state = HSM_ST_ERR;
+}
+
+/**
+ * ata_hsm_ok_in_wq - Check if the qc can be handled in the workqueue.
+ * @ap: the target ata_port
+ * @qc: qc on going
+ *
+ * RETURNS:
+ * 1 if ok in workqueue, 0 otherwise.
+ */
+static inline int ata_hsm_ok_in_wq(struct ata_port *ap, struct ata_queued_cmd *qc)
+{
+ if (qc->tf.flags & ATA_TFLAG_POLLING)
+ return 1;
+
+ if (ap->hsm_task_state == HSM_ST_FIRST) {
+ if (qc->tf.protocol == ATA_PROT_PIO &&
+ (qc->tf.flags & ATA_TFLAG_WRITE))
+ return 1;
+
+ if (ata_is_atapi(qc->tf.protocol) &&
+ !(qc->dev->flags & ATA_DFLAG_CDB_INTR))
+ return 1;
+ }
+
+ return 0;
+}
+
+/**
+ * ata_hsm_qc_complete - finish a qc running on standard HSM
+ * @qc: Command to complete
+ * @in_wq: 1 if called from workqueue, 0 otherwise
+ *
+ * Finish @qc which is running on standard HSM.
+ *
+ * LOCKING:
+ * If @in_wq is zero, spin_lock_irqsave(host lock).
+ * Otherwise, none on entry and grabs host lock.
+ */
+static void ata_hsm_qc_complete(struct ata_queued_cmd *qc, int in_wq)
+{
+ struct ata_port *ap = qc->ap;
+ unsigned long flags;
+
+ if (ap->ops->error_handler) {
+ if (in_wq) {
+ spin_lock_irqsave(ap->lock, flags);
+
+ /* EH might have kicked in while host lock is
+ * released.
+ */
+ qc = ata_qc_from_tag(ap, qc->tag);
+ if (qc) {
+ if (likely(!(qc->err_mask & AC_ERR_HSM))) {
+ ap->ops->irq_on(ap);
+ ata_qc_complete(qc);
+ } else
+ ata_port_freeze(ap);
+ }
+
+ spin_unlock_irqrestore(ap->lock, flags);
+ } else {
+ if (likely(!(qc->err_mask & AC_ERR_HSM)))
+ ata_qc_complete(qc);
+ else
+ ata_port_freeze(ap);
+ }
+ } else {
+ if (in_wq) {
+ spin_lock_irqsave(ap->lock, flags);
+ ap->ops->irq_on(ap);
+ ata_qc_complete(qc);
+ spin_unlock_irqrestore(ap->lock, flags);
+ } else
+ ata_qc_complete(qc);
+ }
+}
+
+/**
+ * ata_hsm_move - move the HSM to the next state.
+ * @ap: the target ata_port
+ * @qc: qc on going
+ * @status: current device status
+ * @in_wq: 1 if called from workqueue, 0 otherwise
+ *
+ * RETURNS:
+ * 1 when poll next status needed, 0 otherwise.
+ */
+int ata_hsm_move(struct ata_port *ap, struct ata_queued_cmd *qc,
+ u8 status, int in_wq)
+{
+ unsigned long flags = 0;
+ int poll_next;
+
+ WARN_ON((qc->flags & ATA_QCFLAG_ACTIVE) == 0);
+
+ /* Make sure ata_qc_issue_prot() does not throw things
+ * like DMA polling into the workqueue. Notice that
+ * in_wq is not equivalent to (qc->tf.flags & ATA_TFLAG_POLLING).
+ */
+ WARN_ON(in_wq != ata_hsm_ok_in_wq(ap, qc));
+
+fsm_start:
+ DPRINTK("ata%u: protocol %d task_state %d (dev_stat 0x%X)\n",
+ ap->print_id, qc->tf.protocol, ap->hsm_task_state, status);
+
+ switch (ap->hsm_task_state) {
+ case HSM_ST_FIRST:
+ /* Send first data block or PACKET CDB */
+
+ /* If polling, we will stay in the work queue after
+ * sending the data. Otherwise, interrupt handler
+ * takes over after sending the data.
+ */
+ poll_next = (qc->tf.flags & ATA_TFLAG_POLLING);
+
+ /* check device status */
+ if (unlikely((status & ATA_DRQ) == 0)) {
+ /* handle BSY=0, DRQ=0 as error */
+ if (likely(status & (ATA_ERR | ATA_DF)))
+ /* device stops HSM for abort/error */
+ qc->err_mask |= AC_ERR_DEV;
+ else
+ /* HSM violation. Let EH handle this */
+ qc->err_mask |= AC_ERR_HSM;
+
+ ap->hsm_task_state = HSM_ST_ERR;
+ goto fsm_start;
+ }
+
+ /* Device should not ask for data transfer (DRQ=1)
+ * when it finds something wrong.
+ * We ignore DRQ here and stop the HSM by
+ * changing hsm_task_state to HSM_ST_ERR and
+ * let the EH abort the command or reset the device.
+ */
+ if (unlikely(status & (ATA_ERR | ATA_DF))) {
+ /* Some ATAPI tape drives forget to clear the ERR bit
+ * when doing the next command (mostly request sense).
+ * We ignore ERR here to workaround and proceed sending
+ * the CDB.
+ */
+ if (!(qc->dev->horkage & ATA_HORKAGE_STUCK_ERR)) {
+ ata_port_printk(ap, KERN_WARNING,
+ "DRQ=1 with device error, "
+ "dev_stat 0x%X\n", status);
+ qc->err_mask |= AC_ERR_HSM;
+ ap->hsm_task_state = HSM_ST_ERR;
+ goto fsm_start;
+ }
+ }
+
+ /* Send the CDB (atapi) or the first data block (ata pio out).
+ * During the state transition, interrupt handler shouldn't
+ * be invoked before the data transfer is complete and
+ * hsm_task_state is changed. Hence, the following locking.
+ */
+ if (in_wq)
+ spin_lock_irqsave(ap->lock, flags);
+
+ if (qc->tf.protocol == ATA_PROT_PIO) {
+ /* PIO data out protocol.
+ * send first data block.
+ */
+
+ /* ata_pio_sectors() might change the state
+ * to HSM_ST_LAST. so, the state is changed here
+ * before ata_pio_sectors().
+ */
+ ap->hsm_task_state = HSM_ST;
+ ata_pio_sectors(qc);
+ } else
+ /* send CDB */
+ atapi_send_cdb(ap, qc);
+
+ if (in_wq)
+ spin_unlock_irqrestore(ap->lock, flags);
+
+ /* if polling, ata_pio_task() handles the rest.
+ * otherwise, interrupt handler takes over from here.
+ */
+ break;
+
+ case HSM_ST:
+ /* complete command or read/write the data register */
+ if (qc->tf.protocol == ATAPI_PROT_PIO) {
+ /* ATAPI PIO protocol */
+ if ((status & ATA_DRQ) == 0) {
+ /* No more data to transfer or device error.
+ * Device error will be tagged in HSM_ST_LAST.
+ */
+ ap->hsm_task_state = HSM_ST_LAST;
+ goto fsm_start;
+ }
+
+ /* Device should not ask for data transfer (DRQ=1)
+ * when it finds something wrong.
+ * We ignore DRQ here and stop the HSM by
+ * changing hsm_task_state to HSM_ST_ERR and
+ * let the EH abort the command or reset the device.
+ */
+ if (unlikely(status & (ATA_ERR | ATA_DF))) {
+ ata_port_printk(ap, KERN_WARNING, "DRQ=1 with "
+ "device error, dev_stat 0x%X\n",
+ status);
+ qc->err_mask |= AC_ERR_HSM;
+ ap->hsm_task_state = HSM_ST_ERR;
+ goto fsm_start;
+ }
+
+ atapi_pio_bytes(qc);
+
+ if (unlikely(ap->hsm_task_state == HSM_ST_ERR))
+ /* bad ireason reported by device */
+ goto fsm_start;
+
+ } else {
+ /* ATA PIO protocol */
+ if (unlikely((status & ATA_DRQ) == 0)) {
+ /* handle BSY=0, DRQ=0 as error */
+ if (likely(status & (ATA_ERR | ATA_DF)))
+ /* device stops HSM for abort/error */
+ qc->err_mask |= AC_ERR_DEV;
+ else
+ /* HSM violation. Let EH handle this.
+ * Phantom devices also trigger this
+ * condition. Mark hint.
+ */
+ qc->err_mask |= AC_ERR_HSM |
+ AC_ERR_NODEV_HINT;
+
+ ap->hsm_task_state = HSM_ST_ERR;
+ goto fsm_start;
+ }
+
+ /* For PIO reads, some devices may ask for
+ * data transfer (DRQ=1) alone with ERR=1.
+ * We respect DRQ here and transfer one
+ * block of junk data before changing the
+ * hsm_task_state to HSM_ST_ERR.
+ *
+ * For PIO writes, ERR=1 DRQ=1 doesn't make
+ * sense since the data block has been
+ * transferred to the device.
+ */
+ if (unlikely(status & (ATA_ERR | ATA_DF))) {
+ /* data might be corrputed */
+ qc->err_mask |= AC_ERR_DEV;
+
+ if (!(qc->tf.flags & ATA_TFLAG_WRITE)) {
+ ata_pio_sectors(qc);
+ status = ata_wait_idle(ap);
+ }
+
+ if (status & (ATA_BUSY | ATA_DRQ))
+ qc->err_mask |= AC_ERR_HSM;
+
+ /* ata_pio_sectors() might change the
+ * state to HSM_ST_LAST. so, the state
+ * is changed after ata_pio_sectors().
+ */
+ ap->hsm_task_state = HSM_ST_ERR;
+ goto fsm_start;
+ }
+
+ ata_pio_sectors(qc);
+
+ if (ap->hsm_task_state == HSM_ST_LAST &&
+ (!(qc->tf.flags & ATA_TFLAG_WRITE))) {
+ /* all data read */
+ status = ata_wait_idle(ap);
+ goto fsm_start;
+ }
+ }
+
+ poll_next = 1;
+ break;
+
+ case HSM_ST_LAST:
+ if (unlikely(!ata_ok(status))) {
+ qc->err_mask |= __ac_err_mask(status);
+ ap->hsm_task_state = HSM_ST_ERR;
+ goto fsm_start;
+ }
+
+ /* no more data to transfer */
+ DPRINTK("ata%u: dev %u command complete, drv_stat 0x%x\n",
+ ap->print_id, qc->dev->devno, status);
+
+ WARN_ON(qc->err_mask);
+
+ ap->hsm_task_state = HSM_ST_IDLE;
+
+ /* complete taskfile transaction */
+ ata_hsm_qc_complete(qc, in_wq);
+
+ poll_next = 0;
+ break;
+
+ case HSM_ST_ERR:
+ /* make sure qc->err_mask is available to
+ * know what's wrong and recover
+ */
+ WARN_ON(qc->err_mask == 0);
+
+ ap->hsm_task_state = HSM_ST_IDLE;
+
+ /* complete taskfile transaction */
+ ata_hsm_qc_complete(qc, in_wq);
+
+ poll_next = 0;
+ break;
+ default:
+ poll_next = 0;
+ BUG();
+ }
+
+ return poll_next;
+}
+
+void ata_pio_task(struct work_struct *work)
+{
+ struct ata_port *ap =
+ container_of(work, struct ata_port, port_task.work);
+ struct ata_queued_cmd *qc = ap->port_task_data;
+ u8 status;
+ int poll_next;
+
+fsm_start:
+ WARN_ON(ap->hsm_task_state == HSM_ST_IDLE);
+
+ /*
+ * This is purely heuristic. This is a fast path.
+ * Sometimes when we enter, BSY will be cleared in
+ * a chk-status or two. If not, the drive is probably seeking
+ * or something. Snooze for a couple msecs, then
+ * chk-status again. If still busy, queue delayed work.
+ */
+ status = ata_busy_wait(ap, ATA_BUSY, 5);
+ if (status & ATA_BUSY) {
+ msleep(2);
+ status = ata_busy_wait(ap, ATA_BUSY, 10);
+ if (status & ATA_BUSY) {
+ ata_pio_queue_task(ap, qc, ATA_SHORT_PAUSE);
+ return;
+ }
+ }
+
+ /* move the HSM */
+ poll_next = ata_hsm_move(ap, qc, status, 1);
+
+ /* another command or interrupt handler
+ * may be running at this point.
+ */
+ if (poll_next)
+ goto fsm_start;
+}
+
+/**
+ * ata_qc_issue_prot - issue taskfile to device in proto-dependent manner
+ * @qc: command to issue to device
+ *
+ * Using various libata functions and hooks, this function
+ * starts an ATA command. ATA commands are grouped into
+ * classes called "protocols", and issuing each type of protocol
+ * is slightly different.
+ *
+ * May be used as the qc_issue() entry in ata_port_operations.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ *
+ * RETURNS:
+ * Zero on success, AC_ERR_* mask on failure
+ */
+unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+
+ /* Use polling pio if the LLD doesn't handle
+ * interrupt driven pio and atapi CDB interrupt.
+ */
+ if (ap->flags & ATA_FLAG_PIO_POLLING) {
+ switch (qc->tf.protocol) {
+ case ATA_PROT_PIO:
+ case ATA_PROT_NODATA:
+ case ATAPI_PROT_PIO:
+ case ATAPI_PROT_NODATA:
+ qc->tf.flags |= ATA_TFLAG_POLLING;
+ break;
+ case ATAPI_PROT_DMA:
+ if (qc->dev->flags & ATA_DFLAG_CDB_INTR)
+ /* see ata_dma_blacklisted() */
+ BUG();
+ break;
+ default:
+ break;
+ }
+ }
+
+ /* select the device */
+ ata_dev_select(ap, qc->dev->devno, 1, 0);
+
+ /* start the command */
+ switch (qc->tf.protocol) {
+ case ATA_PROT_NODATA:
+ if (qc->tf.flags & ATA_TFLAG_POLLING)
+ ata_qc_set_polling(qc);
+
+ ata_tf_to_host(ap, &qc->tf);
+ ap->hsm_task_state = HSM_ST_LAST;
+
+ if (qc->tf.flags & ATA_TFLAG_POLLING)
+ ata_pio_queue_task(ap, qc, 0);
+
+ break;
+
+ case ATA_PROT_DMA:
+ WARN_ON(qc->tf.flags & ATA_TFLAG_POLLING);
+
+ ap->ops->tf_load(ap, &qc->tf); /* load tf registers */
+ ap->ops->bmdma_setup(qc); /* set up bmdma */
+ ap->ops->bmdma_start(qc); /* initiate bmdma */
+ ap->hsm_task_state = HSM_ST_LAST;
+ break;
+
+ case ATA_PROT_PIO:
+ if (qc->tf.flags & ATA_TFLAG_POLLING)
+ ata_qc_set_polling(qc);
+
+ ata_tf_to_host(ap, &qc->tf);
+
+ if (qc->tf.flags & ATA_TFLAG_WRITE) {
+ /* PIO data out protocol */
+ ap->hsm_task_state = HSM_ST_FIRST;
+ ata_pio_queue_task(ap, qc, 0);
+
+ /* always send first data block using
+ * the ata_pio_task() codepath.
+ */
+ } else {
+ /* PIO data in protocol */
+ ap->hsm_task_state = HSM_ST;
+
+ if (qc->tf.flags & ATA_TFLAG_POLLING)
+ ata_pio_queue_task(ap, qc, 0);
+
+ /* if polling, ata_pio_task() handles the rest.
+ * otherwise, interrupt handler takes over from here.
+ */
+ }
+
+ break;
+
+ case ATAPI_PROT_PIO:
+ case ATAPI_PROT_NODATA:
+ if (qc->tf.flags & ATA_TFLAG_POLLING)
+ ata_qc_set_polling(qc);
+
+ ata_tf_to_host(ap, &qc->tf);
+
+ ap->hsm_task_state = HSM_ST_FIRST;
+
+ /* send cdb by polling if no cdb interrupt */
+ if ((!(qc->dev->flags & ATA_DFLAG_CDB_INTR)) ||
+ (qc->tf.flags & ATA_TFLAG_POLLING))
+ ata_pio_queue_task(ap, qc, 0);
+ break;
+
+ case ATAPI_PROT_DMA:
+ WARN_ON(qc->tf.flags & ATA_TFLAG_POLLING);
+
+ ap->ops->tf_load(ap, &qc->tf); /* load tf registers */
+ ap->ops->bmdma_setup(qc); /* set up bmdma */
+ ap->hsm_task_state = HSM_ST_FIRST;
+
+ /* send cdb by polling if no cdb interrupt */
+ if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
+ ata_pio_queue_task(ap, qc, 0);
+ break;
+
+ default:
+ WARN_ON(1);
+ return AC_ERR_SYSTEM;
+ }
+
+ return 0;
+}
+
+/**
+ * ata_host_intr - Handle host interrupt for given (port, task)
+ * @ap: Port on which interrupt arrived (possibly...)
+ * @qc: Taskfile currently active in engine
+ *
+ * Handle host interrupt for given queued command. Currently,
+ * only DMA interrupts are handled. All other commands are
+ * handled via polling with interrupts disabled (nIEN bit).
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ *
+ * RETURNS:
+ * One if interrupt was handled, zero if not (shared irq).
+ */
+inline unsigned int ata_host_intr(struct ata_port *ap,
+ struct ata_queued_cmd *qc)
+{
+ struct ata_eh_info *ehi = &ap->link.eh_info;
+ u8 status, host_stat = 0;
+
+ VPRINTK("ata%u: protocol %d task_state %d\n",
+ ap->print_id, qc->tf.protocol, ap->hsm_task_state);
+
+ /* Check whether we are expecting interrupt in this state */
+ switch (ap->hsm_task_state) {
+ case HSM_ST_FIRST:
+ /* Some pre-ATAPI-4 devices assert INTRQ
+ * at this state when ready to receive CDB.
+ */
+
+ /* Check the ATA_DFLAG_CDB_INTR flag is enough here.
+ * The flag was turned on only for atapi devices. No
+ * need to check ata_is_atapi(qc->tf.protocol) again.
+ */
+ if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
+ goto idle_irq;
+ break;
+ case HSM_ST_LAST:
+ if (qc->tf.protocol == ATA_PROT_DMA ||
+ qc->tf.protocol == ATAPI_PROT_DMA) {
+ /* check status of DMA engine */
+ host_stat = ap->ops->bmdma_status(ap);
+ VPRINTK("ata%u: host_stat 0x%X\n",
+ ap->print_id, host_stat);
+
+ /* if it's not our irq... */
+ if (!(host_stat & ATA_DMA_INTR))
+ goto idle_irq;
+
+ /* before we do anything else, clear DMA-Start bit */
+ ap->ops->bmdma_stop(qc);
+
+ if (unlikely(host_stat & ATA_DMA_ERR)) {
+ /* error when transfering data to/from memory */
+ qc->err_mask |= AC_ERR_HOST_BUS;
+ ap->hsm_task_state = HSM_ST_ERR;
+ }
+ }
+ break;
+ case HSM_ST:
+ break;
+ default:
+ goto idle_irq;
+ }
+
+ /* check altstatus */
+ status = ata_altstatus(ap);
+ if (status & ATA_BUSY)
+ goto idle_irq;
+
+ /* check main status, clearing INTRQ */
+ status = ata_chk_status(ap);
+ if (unlikely(status & ATA_BUSY))
+ goto idle_irq;
+
+ /* ack bmdma irq events */
+ ap->ops->irq_clear(ap);
+
+ ata_hsm_move(ap, qc, status, 0);
+
+ if (unlikely(qc->err_mask) && (qc->tf.protocol == ATA_PROT_DMA ||
+ qc->tf.protocol == ATAPI_PROT_DMA))
+ ata_ehi_push_desc(ehi, "BMDMA stat 0x%x", host_stat);
+
+ return 1; /* irq handled */
+
+idle_irq:
+ ap->stats.idle_irq++;
+
+#ifdef ATA_IRQ_TRAP
+ if ((ap->stats.idle_irq % 1000) == 0) {
+ ata_chk_status(ap);
+ ap->ops->irq_clear(ap);
+ ata_port_printk(ap, KERN_WARNING, "irq trap\n");
+ return 1;
+ }
+#endif
+ return 0; /* irq not handled */
+}
+
+/**
+ * ata_interrupt - Default ATA host interrupt handler
+ * @irq: irq line (unused)
+ * @dev_instance: pointer to our ata_host information structure
+ *
+ * Default interrupt handler for PCI IDE devices. Calls
+ * ata_host_intr() for each port that is not disabled.
+ *
+ * LOCKING:
+ * Obtains host lock during operation.
+ *
+ * RETURNS:
+ * IRQ_NONE or IRQ_HANDLED.
+ */
+irqreturn_t ata_interrupt(int irq, void *dev_instance)
+{
+ struct ata_host *host = dev_instance;
+ unsigned int i;
+ unsigned int handled = 0;
+ unsigned long flags;
+
+ /* TODO: make _irqsave conditional on x86 PCI IDE legacy mode */
+ spin_lock_irqsave(&host->lock, flags);
+
+ for (i = 0; i < host->n_ports; i++) {
+ struct ata_port *ap;
+
+ ap = host->ports[i];
+ if (ap &&
+ !(ap->flags & ATA_FLAG_DISABLED)) {
+ struct ata_queued_cmd *qc;
+
+ qc = ata_qc_from_tag(ap, ap->link.active_tag);
+ if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING)) &&
+ (qc->flags & ATA_QCFLAG_ACTIVE))
+ handled |= ata_host_intr(ap, qc);
+ }
+ }
+
+ spin_unlock_irqrestore(&host->lock, flags);
+
+ return IRQ_RETVAL(handled);
+}
+
+/**
+ * ata_bmdma_freeze - Freeze BMDMA controller port
+ * @ap: port to freeze
+ *
+ * Freeze BMDMA controller port.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+void ata_bmdma_freeze(struct ata_port *ap)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+
+ ap->ctl |= ATA_NIEN;
+ ap->last_ctl = ap->ctl;
+
+ if (ioaddr->ctl_addr)
+ iowrite8(ap->ctl, ioaddr->ctl_addr);
+
+ /* Under certain circumstances, some controllers raise IRQ on
+ * ATA_NIEN manipulation. Also, many controllers fail to mask
+ * previously pending IRQ on ATA_NIEN assertion. Clear it.
+ */
+ ata_chk_status(ap);
+
+ ap->ops->irq_clear(ap);
+}
+
+/**
+ * ata_bmdma_thaw - Thaw BMDMA controller port
+ * @ap: port to thaw
+ *
+ * Thaw BMDMA controller port.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+void ata_bmdma_thaw(struct ata_port *ap)
{
- if (ap->ops->check_altstatus)
- return ap->ops->check_altstatus(ap);
-
- return ioread8(ap->ioaddr.altstatus_addr);
+ /* clear & re-enable interrupts */
+ ata_chk_status(ap);
+ ap->ops->irq_clear(ap);
+ ap->ops->irq_on(ap);
}
/**
- * ata_irq_on - Enable interrupts on a port.
- * @ap: Port on which interrupts are enabled.
+ * ata_devchk - PATA device presence detection
+ * @ap: ATA channel to examine
+ * @device: Device to examine (starting at zero)
*
- * Enable interrupts on a legacy IDE device using MMIO or PIO,
- * wait for idle, clear any pending interrupts.
+ * This technique was originally described in
+ * Hale Landis's ATADRVR (www.ata-atapi.com), and
+ * later found its way into the ATA/ATAPI spec.
+ *
+ * Write a pattern to the ATA shadow registers,
+ * and if a device is present, it will respond by
+ * correctly storing and echoing back the
+ * ATA shadow register contents.
*
* LOCKING:
- * Inherited from caller.
+ * caller.
*/
-u8 ata_irq_on(struct ata_port *ap)
+static unsigned int ata_devchk(struct ata_port *ap, unsigned int device)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
- u8 tmp;
+ u8 nsect, lbal;
- ap->ctl &= ~ATA_NIEN;
- ap->last_ctl = ap->ctl;
+ ap->ops->dev_select(ap, device);
- if (ioaddr->ctl_addr)
- iowrite8(ap->ctl, ioaddr->ctl_addr);
- tmp = ata_wait_idle(ap);
+ iowrite8(0x55, ioaddr->nsect_addr);
+ iowrite8(0xaa, ioaddr->lbal_addr);
- ap->ops->irq_clear(ap);
+ iowrite8(0xaa, ioaddr->nsect_addr);
+ iowrite8(0x55, ioaddr->lbal_addr);
- return tmp;
+ iowrite8(0x55, ioaddr->nsect_addr);
+ iowrite8(0xaa, ioaddr->lbal_addr);
+
+ nsect = ioread8(ioaddr->nsect_addr);
+ lbal = ioread8(ioaddr->lbal_addr);
+
+ if ((nsect == 0x55) && (lbal == 0xaa))
+ return 1; /* we found a device */
+
+ return 0; /* nothing found */
}
/**
- * ata_bmdma_irq_clear - Clear PCI IDE BMDMA interrupt.
- * @ap: Port associated with this ATA transaction.
+ * ata_dev_try_classify - Parse returned ATA device signature
+ * @dev: ATA device to classify (starting at zero)
+ * @present: device seems present
+ * @r_err: Value of error register on completion
*
- * Clear interrupt and error flags in DMA status register.
+ * After an event -- SRST, E.D.D., or SATA COMRESET -- occurs,
+ * an ATA/ATAPI-defined set of values is placed in the ATA
+ * shadow registers, indicating the results of device detection
+ * and diagnostics.
*
- * May be used as the irq_clear() entry in ata_port_operations.
+ * Select the ATA device, and read the values from the ATA shadow
+ * registers. Then parse according to the Error register value,
+ * and the spec-defined values examined by ata_dev_classify().
*
* LOCKING:
- * spin_lock_irqsave(host lock)
+ * caller.
+ *
+ * RETURNS:
+ * Device type - %ATA_DEV_ATA, %ATA_DEV_ATAPI or %ATA_DEV_NONE.
*/
-void ata_bmdma_irq_clear(struct ata_port *ap)
+unsigned int ata_dev_try_classify(struct ata_device *dev, int present,
+ u8 *r_err)
{
- void __iomem *mmio = ap->ioaddr.bmdma_addr;
+ struct ata_port *ap = dev->link->ap;
+ struct ata_taskfile tf;
+ unsigned int class;
+ u8 err;
+
+ ap->ops->dev_select(ap, dev->devno);
+
+ memset(&tf, 0, sizeof(tf));
+
+ ap->ops->tf_read(ap, &tf);
+ err = tf.feature;
+ if (r_err)
+ *r_err = err;
+
+ /* see if device passed diags: continue and warn later */
+ if (err == 0)
+ /* diagnostic fail : do nothing _YET_ */
+ dev->horkage |= ATA_HORKAGE_DIAGNOSTIC;
+ else if (err == 1)
+ /* do nothing */ ;
+ else if ((dev->devno == 0) && (err == 0x81))
+ /* do nothing */ ;
+ else
+ return ATA_DEV_NONE;
- if (!mmio)
- return;
+ /* determine if device is ATA or ATAPI */
+ class = ata_dev_classify(&tf);
- iowrite8(ioread8(mmio + ATA_DMA_STATUS), mmio + ATA_DMA_STATUS);
+ if (class == ATA_DEV_UNKNOWN) {
+ /* If the device failed diagnostic, it's likely to
+ * have reported incorrect device signature too.
+ * Assume ATA device if the device seems present but
+ * device signature is invalid with diagnostic
+ * failure.
+ */
+ if (present && (dev->horkage & ATA_HORKAGE_DIAGNOSTIC))
+ class = ATA_DEV_ATA;
+ else
+ class = ATA_DEV_NONE;
+ } else if ((class == ATA_DEV_ATA) && (ata_chk_status(ap) == 0))
+ class = ATA_DEV_NONE;
+
+ return class;
}
-/**
- * ata_tf_load - send taskfile registers to host controller
- * @ap: Port to which output is sent
- * @tf: ATA taskfile register set
- *
- * Outputs ATA taskfile to standard ATA host controller.
- *
- * LOCKING:
- * Inherited from caller.
- */
-void ata_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
+static int ata_bus_post_reset(struct ata_port *ap, unsigned int devmask,
+ unsigned long deadline)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
- unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
+ unsigned int dev0 = devmask & (1 << 0);
+ unsigned int dev1 = devmask & (1 << 1);
+ int rc, ret = 0;
- if (tf->ctl != ap->last_ctl) {
- if (ioaddr->ctl_addr)
- iowrite8(tf->ctl, ioaddr->ctl_addr);
- ap->last_ctl = tf->ctl;
- ata_wait_idle(ap);
+ /* if device 0 was found in ata_devchk, wait for its
+ * BSY bit to clear
+ */
+ if (dev0) {
+ rc = ata_wait_ready(ap, deadline);
+ if (rc) {
+ if (rc != -ENODEV)
+ return rc;
+ ret = rc;
+ }
}
- if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
- WARN_ON(!ioaddr->ctl_addr);
- iowrite8(tf->hob_feature, ioaddr->feature_addr);
- iowrite8(tf->hob_nsect, ioaddr->nsect_addr);
- iowrite8(tf->hob_lbal, ioaddr->lbal_addr);
- iowrite8(tf->hob_lbam, ioaddr->lbam_addr);
- iowrite8(tf->hob_lbah, ioaddr->lbah_addr);
- VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n",
- tf->hob_feature,
- tf->hob_nsect,
- tf->hob_lbal,
- tf->hob_lbam,
- tf->hob_lbah);
- }
+ /* if device 1 was found in ata_devchk, wait for register
+ * access briefly, then wait for BSY to clear.
+ */
+ if (dev1) {
+ int i;
- if (is_addr) {
- iowrite8(tf->feature, ioaddr->feature_addr);
- iowrite8(tf->nsect, ioaddr->nsect_addr);
- iowrite8(tf->lbal, ioaddr->lbal_addr);
- iowrite8(tf->lbam, ioaddr->lbam_addr);
- iowrite8(tf->lbah, ioaddr->lbah_addr);
- VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
- tf->feature,
- tf->nsect,
- tf->lbal,
- tf->lbam,
- tf->lbah);
- }
+ ap->ops->dev_select(ap, 1);
- if (tf->flags & ATA_TFLAG_DEVICE) {
- iowrite8(tf->device, ioaddr->device_addr);
- VPRINTK("device 0x%X\n", tf->device);
+ /* Wait for register access. Some ATAPI devices fail
+ * to set nsect/lbal after reset, so don't waste too
+ * much time on it. We're gonna wait for !BSY anyway.
+ */
+ for (i = 0; i < 2; i++) {
+ u8 nsect, lbal;
+
+ nsect = ioread8(ioaddr->nsect_addr);
+ lbal = ioread8(ioaddr->lbal_addr);
+ if ((nsect == 1) && (lbal == 1))
+ break;
+ msleep(50); /* give drive a breather */
+ }
+
+ rc = ata_wait_ready(ap, deadline);
+ if (rc) {
+ if (rc != -ENODEV)
+ return rc;
+ ret = rc;
+ }
}
- ata_wait_idle(ap);
+ /* is all this really necessary? */
+ ap->ops->dev_select(ap, 0);
+ if (dev1)
+ ap->ops->dev_select(ap, 1);
+ if (dev0)
+ ap->ops->dev_select(ap, 0);
+
+ return ret;
}
/**
- * ata_tf_read - input device's ATA taskfile shadow registers
- * @ap: Port from which input is read
- * @tf: ATA taskfile register set for storing input
+ * ata_wait_after_reset - wait before checking status after reset
+ * @ap: port containing status register to be polled
+ * @deadline: deadline jiffies for the operation
*
- * Reads ATA taskfile registers for currently-selected device
- * into @tf. Assumes the device has a fully SFF compliant task file
- * layout and behaviour. If you device does not (eg has a different
- * status method) then you will need to provide a replacement tf_read
+ * After reset, we need to pause a while before reading status.
+ * Also, certain combination of controller and device report 0xff
+ * for some duration (e.g. until SATA PHY is up and running)
+ * which is interpreted as empty port in ATA world. This
+ * function also waits for such devices to get out of 0xff
+ * status.
*
* LOCKING:
- * Inherited from caller.
+ * Kernel thread context (may sleep).
*/
-void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
+void ata_wait_after_reset(struct ata_port *ap, unsigned long deadline)
{
- struct ata_ioports *ioaddr = &ap->ioaddr;
+ unsigned long until = jiffies + ATA_TMOUT_FF_WAIT;
+
+ if (time_before(until, deadline))
+ deadline = until;
+
+ /* Spec mandates ">= 2ms" before checking status. We wait
+ * 150ms, because that was the magic delay used for ATAPI
+ * devices in Hale Landis's ATADRVR, for the period of time
+ * between when the ATA command register is written, and then
+ * status is checked. Because waiting for "a while" before
+ * checking status is fine, post SRST, we perform this magic
+ * delay here as well.
+ *
+ * Old drivers/ide uses the 2mS rule and then waits for ready.
+ */
+ msleep(150);
- tf->command = ata_check_status(ap);
- tf->feature = ioread8(ioaddr->error_addr);
- tf->nsect = ioread8(ioaddr->nsect_addr);
- tf->lbal = ioread8(ioaddr->lbal_addr);
- tf->lbam = ioread8(ioaddr->lbam_addr);
- tf->lbah = ioread8(ioaddr->lbah_addr);
- tf->device = ioread8(ioaddr->device_addr);
+ /* Wait for 0xff to clear. Some SATA devices take a long time
+ * to clear 0xff after reset. For example, HHD424020F7SV00
+ * iVDR needs >= 800ms while. Quantum GoVault needs even more
+ * than that.
+ *
+ * Note that some PATA controllers (pata_ali) explode if
+ * status register is read more than once when there's no
+ * device attached.
+ */
+ if (ap->flags & ATA_FLAG_SATA) {
+ while (1) {
+ u8 status = ata_chk_status(ap);
- if (tf->flags & ATA_TFLAG_LBA48) {
- if (likely(ioaddr->ctl_addr)) {
- iowrite8(tf->ctl | ATA_HOB, ioaddr->ctl_addr);
- tf->hob_feature = ioread8(ioaddr->error_addr);
- tf->hob_nsect = ioread8(ioaddr->nsect_addr);
- tf->hob_lbal = ioread8(ioaddr->lbal_addr);
- tf->hob_lbam = ioread8(ioaddr->lbam_addr);
- tf->hob_lbah = ioread8(ioaddr->lbah_addr);
- iowrite8(tf->ctl, ioaddr->ctl_addr);
- ap->last_ctl = tf->ctl;
- } else
- WARN_ON(1);
+ if (status != 0xff || time_after(jiffies, deadline))
+ return;
+
+ msleep(50);
+ }
}
}
-/**
- * ata_exec_command - issue ATA command to host controller
- * @ap: port to which command is being issued
- * @tf: ATA taskfile register set
- *
- * Issues ATA command, with proper synchronization with interrupt
- * handler / other threads.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- */
-void ata_exec_command(struct ata_port *ap, const struct ata_taskfile *tf)
+static int ata_bus_softreset(struct ata_port *ap, unsigned int devmask,
+ unsigned long deadline)
{
- DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
+ struct ata_ioports *ioaddr = &ap->ioaddr;
- iowrite8(tf->command, ap->ioaddr.command_addr);
- ata_pause(ap);
+ DPRINTK("ata%u: bus reset via SRST\n", ap->print_id);
+
+ /* software reset. causes dev0 to be selected */
+ iowrite8(ap->ctl, ioaddr->ctl_addr);
+ udelay(20); /* FIXME: flush */
+ iowrite8(ap->ctl | ATA_SRST, ioaddr->ctl_addr);
+ udelay(20); /* FIXME: flush */
+ iowrite8(ap->ctl, ioaddr->ctl_addr);
+
+ /* wait a while before checking status */
+ ata_wait_after_reset(ap, deadline);
+
+ /* Before we perform post reset processing we want to see if
+ * the bus shows 0xFF because the odd clown forgets the D7
+ * pulldown resistor.
+ */
+ if (ata_chk_status(ap) == 0xFF)
+ return -ENODEV;
+
+ return ata_bus_post_reset(ap, devmask, deadline);
}
/**
- * ata_bmdma_freeze - Freeze BMDMA controller port
- * @ap: port to freeze
+ * ata_std_softreset - reset host port via ATA SRST
+ * @link: ATA link to reset
+ * @classes: resulting classes of attached devices
+ * @deadline: deadline jiffies for the operation
*
- * Freeze BMDMA controller port.
+ * Reset host port using ATA SRST.
*
* LOCKING:
- * Inherited from caller.
+ * Kernel thread context (may sleep)
+ *
+ * RETURNS:
+ * 0 on success, -errno otherwise.
*/
-void ata_bmdma_freeze(struct ata_port *ap)
+int ata_std_softreset(struct ata_link *link, unsigned int *classes,
+ unsigned long deadline)
{
- struct ata_ioports *ioaddr = &ap->ioaddr;
+ struct ata_port *ap = link->ap;
+ unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS;
+ unsigned int devmask = 0;
+ int rc;
+ u8 err;
- ap->ctl |= ATA_NIEN;
- ap->last_ctl = ap->ctl;
+ DPRINTK("ENTER\n");
- if (ioaddr->ctl_addr)
- iowrite8(ap->ctl, ioaddr->ctl_addr);
+ if (ata_link_offline(link)) {
+ classes[0] = ATA_DEV_NONE;
+ goto out;
+ }
- /* Under certain circumstances, some controllers raise IRQ on
- * ATA_NIEN manipulation. Also, many controllers fail to mask
- * previously pending IRQ on ATA_NIEN assertion. Clear it.
- */
- ata_chk_status(ap);
+ /* determine if device 0/1 are present */
+ if (ata_devchk(ap, 0))
+ devmask |= (1 << 0);
+ if (slave_possible && ata_devchk(ap, 1))
+ devmask |= (1 << 1);
+
+ /* select device 0 again */
+ ap->ops->dev_select(ap, 0);
+
+ /* issue bus reset */
+ DPRINTK("about to softreset, devmask=%x\n", devmask);
+ rc = ata_bus_softreset(ap, devmask, deadline);
+ /* if link is occupied, -ENODEV too is an error */
+ if (rc && (rc != -ENODEV || sata_scr_valid(link))) {
+ ata_link_printk(link, KERN_ERR, "SRST failed (errno=%d)\n", rc);
+ return rc;
+ }
- ap->ops->irq_clear(ap);
+ /* determine by signature whether we have ATA or ATAPI devices */
+ classes[0] = ata_dev_try_classify(&link->device[0],
+ devmask & (1 << 0), &err);
+ if (slave_possible && err != 0x81)
+ classes[1] = ata_dev_try_classify(&link->device[1],
+ devmask & (1 << 1), &err);
+
+ out:
+ DPRINTK("EXIT, classes[0]=%u [1]=%u\n", classes[0], classes[1]);
+ return 0;
}
/**
- * ata_bmdma_thaw - Thaw BMDMA controller port
- * @ap: port to thaw
+ * sata_std_hardreset - reset host port via SATA phy reset
+ * @link: link to reset
+ * @class: resulting class of attached device
+ * @deadline: deadline jiffies for the operation
*
- * Thaw BMDMA controller port.
+ * SATA phy-reset host port using DET bits of SControl register,
+ * wait for !BSY and classify the attached device.
*
* LOCKING:
- * Inherited from caller.
+ * Kernel thread context (may sleep)
+ *
+ * RETURNS:
+ * 0 on success, -errno otherwise.
*/
-void ata_bmdma_thaw(struct ata_port *ap)
+int sata_std_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline)
{
- /* clear & re-enable interrupts */
- ata_chk_status(ap);
- ap->ops->irq_clear(ap);
- ap->ops->irq_on(ap);
+ struct ata_port *ap = link->ap;
+ const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context);
+ int rc;
+
+ DPRINTK("ENTER\n");
+
+ /* do hardreset */
+ rc = sata_link_hardreset(link, timing, deadline);
+ if (rc) {
+ ata_link_printk(link, KERN_ERR,
+ "COMRESET failed (errno=%d)\n", rc);
+ return rc;
+ }
+
+ /* TODO: phy layer with polling, timeouts, etc. */
+ if (ata_link_offline(link)) {
+ *class = ATA_DEV_NONE;
+ DPRINTK("EXIT, link offline\n");
+ return 0;
+ }
+
+ /* wait a while before checking status */
+ ata_wait_after_reset(ap, deadline);
+
+ /* If PMP is supported, we have to do follow-up SRST. Note
+ * that some PMPs don't send D2H Reg FIS after hardreset at
+ * all if the first port is empty. Wait for it just for a
+ * second and request follow-up SRST.
+ */
+ if (ap->flags & ATA_FLAG_PMP) {
+ ata_wait_ready(ap, jiffies + HZ);
+ return -EAGAIN;
+ }
+
+ rc = ata_wait_ready(ap, deadline);
+ /* link occupied, -ENODEV too is an error */
+ if (rc) {
+ ata_link_printk(link, KERN_ERR,
+ "COMRESET failed (errno=%d)\n", rc);
+ return rc;
+ }
+
+ ap->ops->dev_select(ap, 0); /* probably unnecessary */
+
+ *class = ata_dev_try_classify(link->device, 1, NULL);
+
+ DPRINTK("EXIT, class=%u\n", *class);
+ return 0;
}
/**
return 0;
}
+/**
+ * ata_std_ports - initialize ioaddr with standard port offsets.
+ * @ioaddr: IO address structure to be initialized
+ *
+ * Utility function which initializes data_addr, error_addr,
+ * feature_addr, nsect_addr, lbal_addr, lbam_addr, lbah_addr,
+ * device_addr, status_addr, and command_addr to standard offsets
+ * relative to cmd_addr.
+ *
+ * Does not set ctl_addr, altstatus_addr, bmdma_addr, or scr_addr.
+ */
+void ata_std_ports(struct ata_ioports *ioaddr)
+{
+ ioaddr->data_addr = ioaddr->cmd_addr + ATA_REG_DATA;
+ ioaddr->error_addr = ioaddr->cmd_addr + ATA_REG_ERR;
+ ioaddr->feature_addr = ioaddr->cmd_addr + ATA_REG_FEATURE;
+ ioaddr->nsect_addr = ioaddr->cmd_addr + ATA_REG_NSECT;
+ ioaddr->lbal_addr = ioaddr->cmd_addr + ATA_REG_LBAL;
+ ioaddr->lbam_addr = ioaddr->cmd_addr + ATA_REG_LBAM;
+ ioaddr->lbah_addr = ioaddr->cmd_addr + ATA_REG_LBAH;
+ ioaddr->device_addr = ioaddr->cmd_addr + ATA_REG_DEVICE;
+ ioaddr->status_addr = ioaddr->cmd_addr + ATA_REG_STATUS;
+ ioaddr->command_addr = ioaddr->cmd_addr + ATA_REG_CMD;
+}
+
/**
* ata_bmdma_setup - Set up PCI IDE BMDMA transaction
* @qc: Info associated with this ATA transaction.
}
/**
- * ata_noop_irq_clear - Noop placeholder for irq_clear
- * @ap: Port associated with this ATA transaction.
+ * ata_bus_reset - reset host port and associated ATA channel
+ * @ap: port to reset
+ *
+ * This is typically the first time we actually start issuing
+ * commands to the ATA channel. We wait for BSY to clear, then
+ * issue EXECUTE DEVICE DIAGNOSTIC command, polling for its
+ * result. Determine what devices, if any, are on the channel
+ * by looking at the device 0/1 error register. Look at the signature
+ * stored in each device's taskfile registers, to determine if
+ * the device is ATA or ATAPI.
+ *
+ * LOCKING:
+ * PCI/etc. bus probe sem.
+ * Obtains host lock.
+ *
+ * SIDE EFFECTS:
+ * Sets ATA_FLAG_DISABLED if bus reset fails.
+ *
+ * DEPRECATED:
+ * This function is only for drivers which still use old EH and
+ * will be removed soon.
*/
-void ata_noop_irq_clear(struct ata_port *ap)
+void ata_bus_reset(struct ata_port *ap)
{
+ struct ata_device *device = ap->link.device;
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS;
+ u8 err;
+ unsigned int dev0, dev1 = 0, devmask = 0;
+ int rc;
+
+ DPRINTK("ENTER, host %u, port %u\n", ap->print_id, ap->port_no);
+
+ /* determine if device 0/1 are present */
+ if (ap->flags & ATA_FLAG_SATA_RESET)
+ dev0 = 1;
+ else {
+ dev0 = ata_devchk(ap, 0);
+ if (slave_possible)
+ dev1 = ata_devchk(ap, 1);
+ }
+
+ if (dev0)
+ devmask |= (1 << 0);
+ if (dev1)
+ devmask |= (1 << 1);
+
+ /* select device 0 again */
+ ap->ops->dev_select(ap, 0);
+
+ /* issue bus reset */
+ if (ap->flags & ATA_FLAG_SRST) {
+ rc = ata_bus_softreset(ap, devmask, jiffies + 40 * HZ);
+ if (rc && rc != -ENODEV)
+ goto err_out;
+ }
+
+ /*
+ * determine by signature whether we have ATA or ATAPI devices
+ */
+ device[0].class = ata_dev_try_classify(&device[0], dev0, &err);
+ if ((slave_possible) && (err != 0x81))
+ device[1].class = ata_dev_try_classify(&device[1], dev1, &err);
+
+ /* is double-select really necessary? */
+ if (device[1].class != ATA_DEV_NONE)
+ ap->ops->dev_select(ap, 1);
+ if (device[0].class != ATA_DEV_NONE)
+ ap->ops->dev_select(ap, 0);
+
+ /* if no devices were detected, disable this port */
+ if ((device[0].class == ATA_DEV_NONE) &&
+ (device[1].class == ATA_DEV_NONE))
+ goto err_out;
+
+ if (ap->flags & (ATA_FLAG_SATA_RESET | ATA_FLAG_SRST)) {
+ /* set up device control for ATA_FLAG_SATA_RESET */
+ iowrite8(ap->ctl, ioaddr->ctl_addr);
+ }
+
+ DPRINTK("EXIT\n");
+ return;
+
+err_out:
+ ata_port_printk(ap, KERN_ERR, "disabling port\n");
+ ata_port_disable(ap);
+
+ DPRINTK("EXIT\n");
}
#ifdef CONFIG_PCI
#endif /* CONFIG_PCI */
+EXPORT_SYMBOL_GPL(ata_sff_port_ops);
+EXPORT_SYMBOL_GPL(ata_bmdma_port_ops);
+EXPORT_SYMBOL_GPL(ata_qc_prep);
+EXPORT_SYMBOL_GPL(ata_dumb_qc_prep);
+EXPORT_SYMBOL_GPL(ata_std_dev_select);
+EXPORT_SYMBOL_GPL(ata_check_status);
+EXPORT_SYMBOL_GPL(ata_altstatus);
+EXPORT_SYMBOL_GPL(ata_busy_sleep);
+EXPORT_SYMBOL_GPL(ata_wait_ready);
+EXPORT_SYMBOL_GPL(ata_tf_load);
+EXPORT_SYMBOL_GPL(ata_tf_read);
+EXPORT_SYMBOL_GPL(ata_exec_command);
+EXPORT_SYMBOL_GPL(ata_data_xfer);
+EXPORT_SYMBOL_GPL(ata_data_xfer_noirq);
+EXPORT_SYMBOL_GPL(ata_irq_on);
+EXPORT_SYMBOL_GPL(ata_bmdma_irq_clear);
+EXPORT_SYMBOL_GPL(ata_hsm_move);
+EXPORT_SYMBOL_GPL(ata_qc_issue_prot);
+EXPORT_SYMBOL_GPL(ata_host_intr);
+EXPORT_SYMBOL_GPL(ata_interrupt);
+EXPORT_SYMBOL_GPL(ata_bmdma_freeze);
+EXPORT_SYMBOL_GPL(ata_bmdma_thaw);
+EXPORT_SYMBOL_GPL(ata_std_prereset);
+EXPORT_SYMBOL_GPL(ata_dev_try_classify);
+EXPORT_SYMBOL_GPL(ata_wait_after_reset);
+EXPORT_SYMBOL_GPL(ata_std_softreset);
+EXPORT_SYMBOL_GPL(sata_std_hardreset);
+EXPORT_SYMBOL_GPL(ata_std_postreset);
+EXPORT_SYMBOL_GPL(ata_bmdma_error_handler);
+EXPORT_SYMBOL_GPL(ata_bmdma_post_internal_cmd);
+EXPORT_SYMBOL_GPL(ata_sff_port_start);
+EXPORT_SYMBOL_GPL(ata_std_ports);
+EXPORT_SYMBOL_GPL(ata_bmdma_setup);
+EXPORT_SYMBOL_GPL(ata_bmdma_start);
+EXPORT_SYMBOL_GPL(ata_bmdma_stop);
+EXPORT_SYMBOL_GPL(ata_bmdma_status);
+EXPORT_SYMBOL_GPL(ata_bus_reset);
+#ifdef CONFIG_PCI
+EXPORT_SYMBOL_GPL(ata_pci_clear_simplex);
+EXPORT_SYMBOL_GPL(ata_pci_default_filter);
+EXPORT_SYMBOL_GPL(ata_pci_init_bmdma);
+EXPORT_SYMBOL_GPL(ata_pci_init_sff_host);
+EXPORT_SYMBOL_GPL(ata_pci_prepare_sff_host);
+EXPORT_SYMBOL_GPL(ata_pci_activate_sff_host);
+EXPORT_SYMBOL_GPL(ata_pci_init_one);
+#endif /* CONFIG_PCI */
unsigned int tag);
extern u64 ata_tf_read_block(struct ata_taskfile *tf, struct ata_device *dev);
extern void ata_dev_disable(struct ata_device *dev);
+extern void ata_pio_queue_task(struct ata_port *ap, void *data,
+ unsigned long delay);
extern void ata_port_flush_task(struct ata_port *ap);
extern unsigned ata_exec_internal(struct ata_device *dev,
struct ata_taskfile *tf, const u8 *cdb,
extern void ata_qc_issue(struct ata_queued_cmd *qc);
extern void __ata_qc_complete(struct ata_queued_cmd *qc);
extern int ata_check_atapi_dma(struct ata_queued_cmd *qc);
-extern void ata_dev_select(struct ata_port *ap, unsigned int device,
- unsigned int wait, unsigned int can_sleep);
extern void swap_buf_le16(u16 *buf, unsigned int buf_words);
extern int ata_flush_cache(struct ata_device *dev);
extern void ata_dev_init(struct ata_device *dev);
extern void ata_eh_finish(struct ata_port *ap);
/* libata-sff.c */
+extern void ata_dev_select(struct ata_port *ap, unsigned int device,
+ unsigned int wait, unsigned int can_sleep);
extern u8 ata_irq_on(struct ata_port *ap);
-
+extern void ata_pio_task(struct work_struct *work);
#endif /* __LIBATA_H__ */
ATAPI_READ_CD = 2, /* READ CD [MSF] */
ATAPI_PASS_THRU = 3, /* SAT pass-thru */
ATAPI_MISC = 4, /* the rest */
+
+ /* Timing constants */
+ ATA_TIMING_SETUP = (1 << 0),
+ ATA_TIMING_ACT8B = (1 << 1),
+ ATA_TIMING_REC8B = (1 << 2),
+ ATA_TIMING_CYC8B = (1 << 3),
+ ATA_TIMING_8BIT = ATA_TIMING_ACT8B | ATA_TIMING_REC8B |
+ ATA_TIMING_CYC8B,
+ ATA_TIMING_ACTIVE = (1 << 4),
+ ATA_TIMING_RECOVER = (1 << 5),
+ ATA_TIMING_CYCLE = (1 << 6),
+ ATA_TIMING_UDMA = (1 << 7),
+ ATA_TIMING_ALL = ATA_TIMING_SETUP | ATA_TIMING_ACT8B |
+ ATA_TIMING_REC8B | ATA_TIMING_CYC8B |
+ ATA_TIMING_ACTIVE | ATA_TIMING_RECOVER |
+ ATA_TIMING_CYCLE | ATA_TIMING_UDMA,
};
enum ata_xfer_mask {
#define FIT(v, vmin, vmax) max_t(short, min_t(short, v, vmax), vmin)
+/*
+ * Core layer - drivers/ata/libata-core.c
+ */
extern const unsigned long sata_deb_timing_normal[];
extern const unsigned long sata_deb_timing_hotplug[];
extern const unsigned long sata_deb_timing_long[];
extern void sata_print_link_status(struct ata_link *link);
extern void ata_port_probe(struct ata_port *);
-extern void ata_bus_reset(struct ata_port *ap);
extern int sata_set_spd(struct ata_link *link);
extern int sata_link_debounce(struct ata_link *link,
const unsigned long *params, unsigned long deadline);
extern int sata_link_resume(struct ata_link *link, const unsigned long *params,
unsigned long deadline);
-extern int ata_std_prereset(struct ata_link *link, unsigned long deadline);
-extern int ata_std_softreset(struct ata_link *link, unsigned int *classes,
- unsigned long deadline);
extern int sata_link_hardreset(struct ata_link *link,
const unsigned long *timing, unsigned long deadline);
-extern int sata_std_hardreset(struct ata_link *link, unsigned int *class,
- unsigned long deadline);
-extern void ata_std_postreset(struct ata_link *link, unsigned int *classes);
extern void ata_port_disable(struct ata_port *);
-extern void ata_std_ports(struct ata_ioports *ioaddr);
extern struct ata_host *ata_host_alloc(struct device *dev, int max_ports);
extern struct ata_host *ata_host_alloc_pinfo(struct device *dev,
extern int ata_sas_slave_configure(struct scsi_device *, struct ata_port *);
extern int ata_sas_queuecmd(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *),
struct ata_port *ap);
-extern unsigned int ata_host_intr(struct ata_port *ap, struct ata_queued_cmd *qc);
extern int sata_scr_valid(struct ata_link *link);
extern int sata_scr_read(struct ata_link *link, int reg, u32 *val);
extern int sata_scr_write(struct ata_link *link, int reg, u32 val);
extern void ata_host_resume(struct ata_host *host);
#endif
extern int ata_ratelimit(void);
-extern int ata_busy_sleep(struct ata_port *ap,
- unsigned long timeout_pat, unsigned long timeout);
-extern void ata_wait_after_reset(struct ata_port *ap, unsigned long deadline);
-extern int ata_wait_ready(struct ata_port *ap, unsigned long deadline);
extern u32 ata_wait_register(void __iomem *reg, u32 mask, u32 val,
unsigned long interval_msec,
unsigned long timeout_msec);
-extern unsigned int ata_dev_try_classify(struct ata_device *dev, int present,
- u8 *r_err);
-
-/*
- * Default driver ops implementations
- */
-extern void ata_tf_load(struct ata_port *ap, const struct ata_taskfile *tf);
-extern void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf);
extern int atapi_cmd_type(u8 opcode);
extern void ata_tf_to_fis(const struct ata_taskfile *tf,
u8 pmp, int is_cmd, u8 *fis);
extern const char *ata_mode_string(unsigned long xfer_mask);
extern unsigned long ata_id_xfermask(const u16 *id);
extern void ata_noop_dev_select(struct ata_port *ap, unsigned int device);
-extern void ata_std_dev_select(struct ata_port *ap, unsigned int device);
-extern u8 ata_check_status(struct ata_port *ap);
-extern u8 ata_altstatus(struct ata_port *ap);
-extern void ata_exec_command(struct ata_port *ap, const struct ata_taskfile *tf);
extern int ata_port_start(struct ata_port *ap);
-extern int ata_sff_port_start(struct ata_port *ap);
-extern irqreturn_t ata_interrupt(int irq, void *dev_instance);
-extern unsigned int ata_data_xfer(struct ata_device *dev,
- unsigned char *buf, unsigned int buflen, int rw);
-extern unsigned int ata_data_xfer_noirq(struct ata_device *dev,
- unsigned char *buf, unsigned int buflen, int rw);
extern int ata_std_qc_defer(struct ata_queued_cmd *qc);
-extern void ata_dumb_qc_prep(struct ata_queued_cmd *qc);
-extern void ata_qc_prep(struct ata_queued_cmd *qc);
extern void ata_noop_qc_prep(struct ata_queued_cmd *qc);
-extern unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc);
extern void ata_sg_init(struct ata_queued_cmd *qc, struct scatterlist *sg,
unsigned int n_elem);
extern unsigned int ata_dev_classify(const struct ata_taskfile *tf);
unsigned int ofs, unsigned int len);
extern void ata_id_c_string(const u16 *id, unsigned char *s,
unsigned int ofs, unsigned int len);
-extern void ata_bmdma_setup(struct ata_queued_cmd *qc);
-extern void ata_bmdma_start(struct ata_queued_cmd *qc);
-extern void ata_bmdma_stop(struct ata_queued_cmd *qc);
-extern u8 ata_bmdma_status(struct ata_port *ap);
-extern void ata_bmdma_irq_clear(struct ata_port *ap);
extern void ata_noop_irq_clear(struct ata_port *ap);
-extern void ata_bmdma_freeze(struct ata_port *ap);
-extern void ata_bmdma_thaw(struct ata_port *ap);
-extern void ata_bmdma_error_handler(struct ata_port *ap);
-extern void ata_bmdma_post_internal_cmd(struct ata_queued_cmd *qc);
-extern int ata_hsm_move(struct ata_port *ap, struct ata_queued_cmd *qc,
- u8 status, int in_wq);
extern void ata_qc_complete(struct ata_queued_cmd *qc);
extern int ata_qc_complete_multiple(struct ata_port *ap, u32 qc_active,
void (*finish_qc)(struct ata_queued_cmd *));
int queue_depth);
extern struct ata_device *ata_dev_pair(struct ata_device *adev);
extern int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev);
-extern u8 ata_irq_on(struct ata_port *ap);
extern int ata_cable_40wire(struct ata_port *ap);
extern int ata_cable_80wire(struct ata_port *ap);
extern int ata_cable_ignore(struct ata_port *ap);
extern int ata_cable_unknown(struct ata_port *ap);
-/*
- * Timing helpers
- */
-
+/* Timing helpers */
extern unsigned int ata_pio_need_iordy(const struct ata_device *);
extern const struct ata_timing *ata_timing_find_mode(u8 xfer_mode);
extern int ata_timing_compute(struct ata_device *, unsigned short,
unsigned int);
extern u8 ata_timing_cycle2mode(unsigned int xfer_shift, int cycle);
-enum {
- ATA_TIMING_SETUP = (1 << 0),
- ATA_TIMING_ACT8B = (1 << 1),
- ATA_TIMING_REC8B = (1 << 2),
- ATA_TIMING_CYC8B = (1 << 3),
- ATA_TIMING_8BIT = ATA_TIMING_ACT8B | ATA_TIMING_REC8B |
- ATA_TIMING_CYC8B,
- ATA_TIMING_ACTIVE = (1 << 4),
- ATA_TIMING_RECOVER = (1 << 5),
- ATA_TIMING_CYCLE = (1 << 6),
- ATA_TIMING_UDMA = (1 << 7),
- ATA_TIMING_ALL = ATA_TIMING_SETUP | ATA_TIMING_ACT8B |
- ATA_TIMING_REC8B | ATA_TIMING_CYC8B |
- ATA_TIMING_ACTIVE | ATA_TIMING_RECOVER |
- ATA_TIMING_CYCLE | ATA_TIMING_UDMA,
+/* PCI */
+#ifdef CONFIG_PCI
+struct pci_dev;
+
+struct pci_bits {
+ unsigned int reg; /* PCI config register to read */
+ unsigned int width; /* 1 (8 bit), 2 (16 bit), 4 (32 bit) */
+ unsigned long mask;
+ unsigned long val;
};
-/* libata-acpi.c */
+extern int pci_test_config_bits(struct pci_dev *pdev, const struct pci_bits *bits);
+extern void ata_pci_remove_one(struct pci_dev *pdev);
+
+#ifdef CONFIG_PM
+extern void ata_pci_device_do_suspend(struct pci_dev *pdev, pm_message_t mesg);
+extern int __must_check ata_pci_device_do_resume(struct pci_dev *pdev);
+extern int ata_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg);
+extern int ata_pci_device_resume(struct pci_dev *pdev);
+#endif /* CONFIG_PM */
+#endif /* CONFIG_PCI */
+
+/*
+ * ACPI - drivers/ata/libata-acpi.c
+ */
#ifdef CONFIG_ATA_ACPI
static inline const struct ata_acpi_gtm *ata_acpi_init_gtm(struct ata_port *ap)
{
}
#endif
-#ifdef CONFIG_PCI
-struct pci_dev;
-
-extern int ata_pci_init_one(struct pci_dev *pdev,
- const struct ata_port_info * const * ppi,
- struct scsi_host_template *sht, void *host_priv);
-extern void ata_pci_remove_one(struct pci_dev *pdev);
-#ifdef CONFIG_PM
-extern void ata_pci_device_do_suspend(struct pci_dev *pdev, pm_message_t mesg);
-extern int __must_check ata_pci_device_do_resume(struct pci_dev *pdev);
-extern int ata_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg);
-extern int ata_pci_device_resume(struct pci_dev *pdev);
-#endif
-extern int ata_pci_clear_simplex(struct pci_dev *pdev);
-
-struct pci_bits {
- unsigned int reg; /* PCI config register to read */
- unsigned int width; /* 1 (8 bit), 2 (16 bit), 4 (32 bit) */
- unsigned long mask;
- unsigned long val;
-};
-
-extern int ata_pci_init_sff_host(struct ata_host *host);
-extern int ata_pci_init_bmdma(struct ata_host *host);
-extern int ata_pci_prepare_sff_host(struct pci_dev *pdev,
- const struct ata_port_info * const * ppi,
- struct ata_host **r_host);
-extern int ata_pci_activate_sff_host(struct ata_host *host,
- irq_handler_t irq_handler,
- struct scsi_host_template *sht);
-extern int pci_test_config_bits(struct pci_dev *pdev, const struct pci_bits *bits);
-extern unsigned long ata_pci_default_filter(struct ata_device *dev,
- unsigned long xfer_mask);
-#endif /* CONFIG_PCI */
-
/*
- * PMP
+ * PMP - drivers/ata/libata-pmp.c
*/
extern int sata_pmp_qc_defer_cmd_switch(struct ata_queued_cmd *qc);
extern int sata_pmp_std_prereset(struct ata_link *link, unsigned long deadline);
extern void sata_pmp_error_handler(struct ata_port *ap);
/*
- * EH
+ * EH - drivers/ata/libata-eh.c
*/
extern void ata_port_schedule_eh(struct ata_port *ap);
extern int ata_link_abort(struct ata_link *link);
extern const struct ata_port_operations ata_base_port_ops;
extern const struct ata_port_operations sata_port_ops;
extern const struct ata_port_operations sata_pmp_port_ops;
-extern const struct ata_port_operations ata_sff_port_ops;
-extern const struct ata_port_operations ata_bmdma_port_ops;
#define ATA_BASE_SHT(drv_name) \
.module = THIS_MODULE, \
.slave_destroy = ata_scsi_slave_destroy, \
.bios_param = ata_std_bios_param
-/* PIO only, sg_tablesize and dma_boundary limits can be removed */
-#define ATA_PIO_SHT(drv_name) \
- ATA_BASE_SHT(drv_name), \
- .sg_tablesize = LIBATA_MAX_PRD, \
- .dma_boundary = ATA_DMA_BOUNDARY
-
-#define ATA_BMDMA_SHT(drv_name) \
- ATA_BASE_SHT(drv_name), \
- .sg_tablesize = LIBATA_MAX_PRD, \
- .dma_boundary = ATA_DMA_BOUNDARY
-
#define ATA_NCQ_SHT(drv_name) \
ATA_BASE_SHT(drv_name), \
.change_queue_depth = ata_scsi_change_queue_depth
for ((dev) = (link)->device + ata_link_max_devices(link) - 1; \
(dev) >= (link)->device || ((dev) = NULL); (dev)--)
-static inline u8 ata_chk_status(struct ata_port *ap)
-{
- return ap->ops->check_status(ap);
-}
-
/**
* ata_ncq_enabled - Test whether NCQ is enabled
* @dev: ATA device to test for
ATA_DFLAG_NCQ)) == ATA_DFLAG_NCQ;
}
-/**
- * ata_pause - Flush writes and pause 400 nanoseconds.
- * @ap: Port to wait for.
- *
- * LOCKING:
- * Inherited from caller.
- */
-
-static inline void ata_pause(struct ata_port *ap)
-{
- ata_altstatus(ap);
- ndelay(400);
-}
-
-
-/**
- * ata_busy_wait - Wait for a port status register
- * @ap: Port to wait for.
- * @bits: bits that must be clear
- * @max: number of 10uS waits to perform
- *
- * Waits up to max*10 microseconds for the selected bits in the port's
- * status register to be cleared.
- * Returns final value of status register.
- *
- * LOCKING:
- * Inherited from caller.
- */
-
-static inline u8 ata_busy_wait(struct ata_port *ap, unsigned int bits,
- unsigned int max)
-{
- u8 status;
-
- do {
- udelay(10);
- status = ata_chk_status(ap);
- max--;
- } while (status != 0xff && (status & bits) && (max > 0));
-
- return status;
-}
-
-
-/**
- * ata_wait_idle - Wait for a port to be idle.
- * @ap: Port to wait for.
- *
- * Waits up to 10ms for port's BUSY and DRQ signals to clear.
- * Returns final value of status register.
- *
- * LOCKING:
- * Inherited from caller.
- */
-
-static inline u8 ata_wait_idle(struct ata_port *ap)
-{
- u8 status = ata_busy_wait(ap, ATA_BUSY | ATA_DRQ, 1000);
-
-#ifdef ATA_DEBUG
- if (status != 0xff && (status & (ATA_BUSY | ATA_DRQ)))
- ata_port_printk(ap, KERN_DEBUG, "abnormal Status 0x%X\n",
- status);
-#endif
-
- return status;
-}
-
static inline void ata_qc_set_polling(struct ata_queued_cmd *qc)
{
qc->tf.ctl |= ATA_NIEN;
return *(struct ata_port **)&host->hostdata[0];
}
+/**************************************************************************
+ * SFF - drivers/ata/libata-sff.c
+ */
+extern const struct ata_port_operations ata_sff_port_ops;
+extern const struct ata_port_operations ata_bmdma_port_ops;
+
+/* PIO only, sg_tablesize and dma_boundary limits can be removed */
+#define ATA_PIO_SHT(drv_name) \
+ ATA_BASE_SHT(drv_name), \
+ .sg_tablesize = LIBATA_MAX_PRD, \
+ .dma_boundary = ATA_DMA_BOUNDARY
+
+#define ATA_BMDMA_SHT(drv_name) \
+ ATA_BASE_SHT(drv_name), \
+ .sg_tablesize = LIBATA_MAX_PRD, \
+ .dma_boundary = ATA_DMA_BOUNDARY
+
+extern void ata_qc_prep(struct ata_queued_cmd *qc);
+extern void ata_dumb_qc_prep(struct ata_queued_cmd *qc);
+extern void ata_std_dev_select(struct ata_port *ap, unsigned int device);
+extern u8 ata_check_status(struct ata_port *ap);
+extern u8 ata_altstatus(struct ata_port *ap);
+extern int ata_busy_sleep(struct ata_port *ap,
+ unsigned long timeout_pat, unsigned long timeout);
+extern int ata_wait_ready(struct ata_port *ap, unsigned long deadline);
+extern void ata_tf_load(struct ata_port *ap, const struct ata_taskfile *tf);
+extern void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf);
+extern void ata_exec_command(struct ata_port *ap, const struct ata_taskfile *tf);
+extern unsigned int ata_data_xfer(struct ata_device *dev,
+ unsigned char *buf, unsigned int buflen, int rw);
+extern unsigned int ata_data_xfer_noirq(struct ata_device *dev,
+ unsigned char *buf, unsigned int buflen, int rw);
+extern u8 ata_irq_on(struct ata_port *ap);
+extern void ata_bmdma_irq_clear(struct ata_port *ap);
+extern int ata_hsm_move(struct ata_port *ap, struct ata_queued_cmd *qc,
+ u8 status, int in_wq);
+extern unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc);
+extern unsigned int ata_host_intr(struct ata_port *ap, struct ata_queued_cmd *qc);
+extern irqreturn_t ata_interrupt(int irq, void *dev_instance);
+extern void ata_bmdma_freeze(struct ata_port *ap);
+extern void ata_bmdma_thaw(struct ata_port *ap);
+extern int ata_std_prereset(struct ata_link *link, unsigned long deadline);
+extern unsigned int ata_dev_try_classify(struct ata_device *dev, int present,
+ u8 *r_err);
+extern void ata_wait_after_reset(struct ata_port *ap, unsigned long deadline);
+extern int ata_std_softreset(struct ata_link *link, unsigned int *classes,
+ unsigned long deadline);
+extern int sata_std_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline);
+extern void ata_std_postreset(struct ata_link *link, unsigned int *classes);
+extern void ata_bmdma_error_handler(struct ata_port *ap);
+extern void ata_bmdma_post_internal_cmd(struct ata_queued_cmd *qc);
+extern int ata_sff_port_start(struct ata_port *ap);
+extern void ata_std_ports(struct ata_ioports *ioaddr);
+extern void ata_bmdma_setup(struct ata_queued_cmd *qc);
+extern void ata_bmdma_start(struct ata_queued_cmd *qc);
+extern void ata_bmdma_stop(struct ata_queued_cmd *qc);
+extern u8 ata_bmdma_status(struct ata_port *ap);
+extern void ata_bus_reset(struct ata_port *ap);
+
+#ifdef CONFIG_PCI
+extern int ata_pci_clear_simplex(struct pci_dev *pdev);
+extern unsigned long ata_pci_default_filter(struct ata_device *dev,
+ unsigned long xfer_mask);
+extern int ata_pci_init_bmdma(struct ata_host *host);
+extern int ata_pci_init_sff_host(struct ata_host *host);
+extern int ata_pci_prepare_sff_host(struct pci_dev *pdev,
+ const struct ata_port_info * const * ppi,
+ struct ata_host **r_host);
+extern int ata_pci_activate_sff_host(struct ata_host *host,
+ irq_handler_t irq_handler,
+ struct scsi_host_template *sht);
+extern int ata_pci_init_one(struct pci_dev *pdev,
+ const struct ata_port_info * const * ppi,
+ struct scsi_host_template *sht, void *host_priv);
+#endif /* CONFIG_PCI */
+
+static inline u8 ata_chk_status(struct ata_port *ap)
+{
+ return ap->ops->check_status(ap);
+}
+
+/**
+ * ata_pause - Flush writes and pause 400 nanoseconds.
+ * @ap: Port to wait for.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static inline void ata_pause(struct ata_port *ap)
+{
+ ata_altstatus(ap);
+ ndelay(400);
+}
+
+/**
+ * ata_busy_wait - Wait for a port status register
+ * @ap: Port to wait for.
+ * @bits: bits that must be clear
+ * @max: number of 10uS waits to perform
+ *
+ * Waits up to max*10 microseconds for the selected bits in the port's
+ * status register to be cleared.
+ * Returns final value of status register.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static inline u8 ata_busy_wait(struct ata_port *ap, unsigned int bits,
+ unsigned int max)
+{
+ u8 status;
+
+ do {
+ udelay(10);
+ status = ata_chk_status(ap);
+ max--;
+ } while (status != 0xff && (status & bits) && (max > 0));
+
+ return status;
+}
+
+/**
+ * ata_wait_idle - Wait for a port to be idle.
+ * @ap: Port to wait for.
+ *
+ * Waits up to 10ms for port's BUSY and DRQ signals to clear.
+ * Returns final value of status register.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static inline u8 ata_wait_idle(struct ata_port *ap)
+{
+ u8 status = ata_busy_wait(ap, ATA_BUSY | ATA_DRQ, 1000);
+
+#ifdef ATA_DEBUG
+ if (status != 0xff && (status & (ATA_BUSY | ATA_DRQ)))
+ ata_port_printk(ap, KERN_DEBUG, "abnormal Status 0x%X\n",
+ status);
+#endif
+
+ return status;
+}
+
#endif /* __LINUX_LIBATA_H__ */
projects / linux-2.6-omap-h63xx.git / commitdiff