Blackfin arch: Add AD7879 defaults for the Blackfin Landscape LCD EZ-Extender

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>

diff --git a/arch/blackfin/mach-bf527/boards/ezbrd.c b/arch/blackfin/mach-bf527/boards/ezbrd.c
index 6f6ce180910fc85cfef8c7e78056a05ff2798d61..0314bd3355eba4a76123c21ad2b51b625c5e324b 100644 (file)
--- a/arch/blackfin/mach-bf527/boards/ezbrd.c
+++ b/arch/blackfin/mach-bf527/boards/ezbrd.c
@@ -288,6 +288,30 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 };
 #endif
 
+#if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#include <linux/spi/ad7879.h>
+static const struct ad7879_platform_data bfin_ad7879_ts_info = {
+       .model                  = 7879, /* Model = AD7879 */
+       .x_plate_ohms           = 620,  /* 620 Ohm from the touch datasheet */
+       .pressure_max           = 10000,
+       .pressure_min           = 0,
+       .first_conversion_delay = 3,    /* wait 512us before do a first conversion */
+       .acquisition_time       = 1,    /* 4us acquisition time per sample */
+       .median                 = 2,    /* do 8 measurements */
+       .averaging              = 1,    /* take the average of 4 middle samples */
+       .pen_down_acc_interval  = 255,  /* 9.4 ms */
+       .gpio_output            = 1,    /* configure AUX/VBAT/GPIO as GPIO output */
+       .gpio_default           = 1,    /* During initialization set GPIO = HIGH */
+};
+#endif
+
+#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
+       .enable_dma = 0,
+       .bits_per_word = 16,
+};
+#endif
+
 #if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
         && defined(CONFIG_SND_SOC_WM8731_SPI)
 static struct bfin5xx_spi_chip spi_wm8731_chip_info = {
@@ -386,6 +410,18 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .controller_data = &spi_ad7877_chip_info,
        },
 #endif
+#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+       {
+               .modalias = "ad7879",
+               .platform_data = &bfin_ad7879_ts_info,
+               .irq = IRQ_PG0,
+               .max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
+               .bus_num = 0,
+               .chip_select = 5,
+               .controller_data = &spi_ad7879_chip_info,
+               .mode = SPI_CPHA | SPI_CPOL,
+       },
+#endif
 #if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
         && defined(CONFIG_SND_SOC_WM8731_SPI)
        {

diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c
index 28cb8f1a39e6fed1dbf523d7f1f2e29051cdaef0..9454fb7b18c3e4d403f5fb09acbfb38b4f682fa8 100644 (file)
--- a/arch/blackfin/mach-bf527/boards/ezkit.c
+++ b/arch/blackfin/mach-bf527/boards/ezkit.c
@@ -534,6 +534,30 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 };
 #endif
 
+#if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#include <linux/spi/ad7879.h>
+static const struct ad7879_platform_data bfin_ad7879_ts_info = {
+       .model                  = 7879, /* Model = AD7879 */
+       .x_plate_ohms           = 620,  /* 620 Ohm from the touch datasheet */
+       .pressure_max           = 10000,
+       .pressure_min           = 0,
+       .first_conversion_delay = 3,    /* wait 512us before do a first conversion */
+       .acquisition_time       = 1,    /* 4us acquisition time per sample */
+       .median                 = 2,    /* do 8 measurements */
+       .averaging              = 1,    /* take the average of 4 middle samples */
+       .pen_down_acc_interval  = 255,  /* 9.4 ms */
+       .gpio_output            = 1,    /* configure AUX/VBAT/GPIO as GPIO output */
+       .gpio_default           = 1,    /* During initialization set GPIO = HIGH */
+};
+#endif
+
+#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
+       .enable_dma = 0,
+       .bits_per_word = 16,
+};
+#endif
+
 #if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
         && defined(CONFIG_SND_SOC_WM8731_SPI)
 static struct bfin5xx_spi_chip spi_wm8731_chip_info = {
@@ -624,6 +648,18 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .controller_data = &spi_ad7877_chip_info,
        },
 #endif
+#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+       {
+               .modalias = "ad7879",
+               .platform_data = &bfin_ad7879_ts_info,
+               .irq = IRQ_PF8,
+               .max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
+               .bus_num = 0,
+               .chip_select = 3,
+               .controller_data = &spi_ad7879_chip_info,
+               .mode = SPI_CPHA | SPI_CPOL,
+       },
+#endif
 #if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
         && defined(CONFIG_SND_SOC_WM8731_SPI)
        {