]> pilppa.com Git - linux-2.6-omap-h63xx.git/commitdiff
pdc202xx_old: rewrite mode programming code (v2)
authorBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tue, 15 May 2007 22:51:41 +0000 (00:51 +0200)
committerBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tue, 15 May 2007 22:51:41 +0000 (00:51 +0200)
This patch is based on the documentation (I would like to thank Promise
for it) and also partially on the older vendor driver.

Rewrite mode programming code:

* disable 66MHz clock in pdc202xx_tune_chipset() so it is correctly disabled
  even if both devices on the channel are not DMA capable and after reset

* enable/disable IORDY and PREFETCH bits in pdc202xx_tune_chipset()
  as they need to be setup correctly also for PIO only devices, plus IORDY
  wasn't disabled for non-IORDY devices and PREFETCH wasn't disabled for
  ATAPI devices

* remove dead code for setting SYNC_ERDDY_EN bits from config_chipset_for_dma()
  (driver sets ->autotune to 1 so PIO modes are always programmed => lower
   nibble of register A never equals 4 => "chipset_is_set" is always true)

* enable PIO mode programming for all ATAPI devices
  (it was limited to ->media == ide_cdrom devices)

* remove extra reads of registers A/B/C, don't read register D et all

* do clearing / programming of registers A/B/C in one go
  (gets rid of extra PCI config space read/write cycle)

* set initial values of drive_conf/AP/BP/CP variables to zero
  (paranoia for the case when PCI reads fail)

* remove XFER_UDMA6 to XFER_UDMA5 remapping case - it can't happen
  (ide_rate_filter() takes care of it)

* fix XFER_MW_DMA0 timings (they were overclocked, use the official ones)

* fix bitmasks for clearing bits of register B:

  - when programming DMA mode bit 0x10 of register B was cleared which
    resulted in overclocked PIO timing setting (iff PIO0 was used)

  - when programming PIO mode bits 0x18 weren't cleared so suboptimal
    timings were used for PIO1-4 if PIO0 was previously set (bit 0x10)
    and for PIO0/3/4 if PIO1/2 was previously set (bit 0x08)

* add FIXME comment about missing locking for 66MHz clock register

Also while at it:

* remove unused defines

* do a few cosmetic / CodingStyle fixes

* bump driver version

v2:
* in pdc202xx_tune_chipset() the old content of drive configuration
  registers is used only by the debugging code so cover "drive_conf"
  PCI registers read by #if PDC202XX_DEBUG_DRIVE_INFO
  (Noticed by Sergei Shtylyov)

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
drivers/ide/pci/pdc202xx_old.c

index 7146fe3f6ba7bdffd0bc9bafaea0afd2e8b8ab64..a6dd9c815342b16ab2bcbedc2f4f6e72922c2fea 100644 (file)
@@ -1,8 +1,9 @@
 /*
- *  linux/drivers/ide/pci/pdc202xx_old.c       Version 0.36    Sept 11, 2002
+ *  linux/drivers/ide/pci/pdc202xx_old.c       Version 0.50    Mar 3, 2007
  *
  *  Copyright (C) 1998-2002            Andre Hedrick <andre@linux-ide.org>
  *  Copyright (C) 2006-2007            MontaVista Software, Inc.
+ *  Copyright (C) 2007                 Bartlomiej Zolnierkiewicz
  *
  *  Promise Ultra33 cards with BIOS v1.20 through 1.28 will need this
  *  compiled into the kernel if you have more than one card installed.
@@ -60,45 +61,7 @@ static const char *pdc_quirk_drives[] = {
        NULL
 };
 
-/* A Register */
-#define        SYNC_ERRDY_EN   0xC0
-
-#define        SYNC_IN         0x80    /* control bit, different for master vs. slave drives */
-#define        ERRDY_EN        0x40    /* control bit, different for master vs. slave drives */
-#define        IORDY_EN        0x20    /* PIO: IOREADY */
-#define        PREFETCH_EN     0x10    /* PIO: PREFETCH */
-
-#define        PA3             0x08    /* PIO"A" timing */
-#define        PA2             0x04    /* PIO"A" timing */
-#define        PA1             0x02    /* PIO"A" timing */
-#define        PA0             0x01    /* PIO"A" timing */
-
-/* B Register */
-
-#define        MB2             0x80    /* DMA"B" timing */
-#define        MB1             0x40    /* DMA"B" timing */
-#define        MB0             0x20    /* DMA"B" timing */
-
-#define        PB4             0x10    /* PIO_FORCE 1:0 */
-
-#define        PB3             0x08    /* PIO"B" timing */     /* PIO flow Control mode */
-#define        PB2             0x04    /* PIO"B" timing */     /* PIO 4 */
-#define        PB1             0x02    /* PIO"B" timing */     /* PIO 3 half */
-#define        PB0             0x01    /* PIO"B" timing */     /* PIO 3 other half */
-
-/* C Register */
-#define        IORDYp_NO_SPEED 0x4F
-#define        SPEED_DIS       0x0F
-
-#define        DMARQp          0x80
-#define        IORDYp          0x40
-#define        DMAR_EN         0x20
-#define        DMAW_EN         0x10
-
-#define        MC3             0x08    /* DMA"C" timing */
-#define        MC2             0x04    /* DMA"C" timing */
-#define        MC1             0x02    /* DMA"C" timing */
-#define        MC0             0x01    /* DMA"C" timing */
+static void pdc_old_disable_66MHz_clock(ide_hwif_t *);
 
 static int pdc202xx_tune_chipset (ide_drive_t *drive, u8 xferspeed)
 {
@@ -107,52 +70,25 @@ static int pdc202xx_tune_chipset (ide_drive_t *drive, u8 xferspeed)
        u8 drive_pci            = 0x60 + (drive->dn << 2);
        u8 speed                = ide_rate_filter(drive, xferspeed);
 
-       u32                     drive_conf;
-       u8                      AP, BP, CP, DP;
+       u8                      AP = 0, BP = 0, CP = 0;
        u8                      TA = 0, TB = 0, TC = 0;
 
-       if (drive->media != ide_disk &&
-               drive->media != ide_cdrom && speed < XFER_SW_DMA_0)
-               return -1;
-
+#if PDC202XX_DEBUG_DRIVE_INFO
+       u32                     drive_conf = 0;
        pci_read_config_dword(dev, drive_pci, &drive_conf);
-       pci_read_config_byte(dev, (drive_pci), &AP);
-       pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
-       pci_read_config_byte(dev, (drive_pci)|0x02, &CP);
-       pci_read_config_byte(dev, (drive_pci)|0x03, &DP);
-
-       if (speed < XFER_SW_DMA_0) {
-               if ((AP & 0x0F) || (BP & 0x07)) {
-                       /* clear PIO modes of lower 8421 bits of A Register */
-                       pci_write_config_byte(dev, (drive_pci), AP &~0x0F);
-                       pci_read_config_byte(dev, (drive_pci), &AP);
+#endif
 
-                       /* clear PIO modes of lower 421 bits of B Register */
-                       pci_write_config_byte(dev, (drive_pci)|0x01, BP &~0x07);
-                       pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
-
-                       pci_read_config_byte(dev, (drive_pci), &AP);
-                       pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
-               }
-       } else {
-               if ((BP & 0xF0) && (CP & 0x0F)) {
-                       /* clear DMA modes of upper 842 bits of B Register */
-                       /* clear PIO forced mode upper 1 bit of B Register */
-                       pci_write_config_byte(dev, (drive_pci)|0x01, BP &~0xF0);
-                       pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
-
-                       /* clear DMA modes of lower 8421 bits of C Register */
-                       pci_write_config_byte(dev, (drive_pci)|0x02, CP &~0x0F);
-                       pci_read_config_byte(dev, (drive_pci)|0x02, &CP);
-               }
-       }
+       /*
+        * TODO: do this once per channel
+        */
+       if (dev->device != PCI_DEVICE_ID_PROMISE_20246)
+               pdc_old_disable_66MHz_clock(hwif);
 
-       pci_read_config_byte(dev, (drive_pci), &AP);
-       pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
-       pci_read_config_byte(dev, (drive_pci)|0x02, &CP);
+       pci_read_config_byte(dev, drive_pci,     &AP);
+       pci_read_config_byte(dev, drive_pci + 1, &BP);
+       pci_read_config_byte(dev, drive_pci + 2, &CP);
 
        switch(speed) {
-               case XFER_UDMA_6:       speed = XFER_UDMA_5;
                case XFER_UDMA_5:
                case XFER_UDMA_4:       TB = 0x20; TC = 0x01; break;
                case XFER_UDMA_2:       TB = 0x20; TC = 0x01; break;
@@ -161,7 +97,7 @@ static int pdc202xx_tune_chipset (ide_drive_t *drive, u8 xferspeed)
                case XFER_UDMA_0:
                case XFER_MW_DMA_2:     TB = 0x60; TC = 0x03; break;
                case XFER_MW_DMA_1:     TB = 0x60; TC = 0x04; break;
-               case XFER_MW_DMA_0:
+               case XFER_MW_DMA_0:     TB = 0xE0; TC = 0x0F; break;
                case XFER_SW_DMA_2:     TB = 0x60; TC = 0x05; break;
                case XFER_SW_DMA_1:     TB = 0x80; TC = 0x06; break;
                case XFER_SW_DMA_0:     TB = 0xC0; TC = 0x0B; break;
@@ -174,25 +110,39 @@ static int pdc202xx_tune_chipset (ide_drive_t *drive, u8 xferspeed)
        }
 
        if (speed < XFER_SW_DMA_0) {
-               pci_write_config_byte(dev, (drive_pci), AP|TA);
-               pci_write_config_byte(dev, (drive_pci)|0x01, BP|TB);
+               /*
+                * preserve SYNC_INT / ERDDY_EN bits while clearing
+                * Prefetch_EN / IORDY_EN / PA[3:0] bits of register A
+                */
+               AP &= ~0x3f;
+               if (drive->id->capability & 4)
+                       AP |= 0x20;     /* set IORDY_EN bit */
+               if (drive->media == ide_disk)
+                       AP |= 0x10;     /* set Prefetch_EN bit */
+               /* clear PB[4:0] bits of register B */
+               BP &= ~0x1f;
+               pci_write_config_byte(dev, drive_pci,     AP | TA);
+               pci_write_config_byte(dev, drive_pci + 1, BP | TB);
        } else {
-               pci_write_config_byte(dev, (drive_pci)|0x01, BP|TB);
-               pci_write_config_byte(dev, (drive_pci)|0x02, CP|TC);
+               /* clear MB[2:0] bits of register B */
+               BP &= ~0xe0;
+               /* clear MC[3:0] bits of register C */
+               CP &= ~0x0f;
+               pci_write_config_byte(dev, drive_pci + 1, BP | TB);
+               pci_write_config_byte(dev, drive_pci + 2, CP | TC);
        }
 
 #if PDC202XX_DEBUG_DRIVE_INFO
        printk(KERN_DEBUG "%s: %s drive%d 0x%08x ",
                drive->name, ide_xfer_verbose(speed),
                drive->dn, drive_conf);
-               pci_read_config_dword(dev, drive_pci, &drive_conf);
+       pci_read_config_dword(dev, drive_pci, &drive_conf);
        printk("0x%08x\n", drive_conf);
-#endif /* PDC202XX_DEBUG_DRIVE_INFO */
+#endif
 
-       return (ide_config_drive_speed(drive, speed));
+       return ide_config_drive_speed(drive, speed);
 }
 
-
 static void pdc202xx_tune_drive(ide_drive_t *drive, u8 pio)
 {
        pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
@@ -210,6 +160,8 @@ static u8 pdc202xx_old_cable_detect (ide_hwif_t *hwif)
  * Set the control register to use the 66MHz system
  * clock for UDMA 3/4/5 mode operation when necessary.
  *
+ * FIXME: this register is shared by both channels, some locking is needed
+ *
  * It may also be possible to leave the 66MHz clock on
  * and readjust the timing parameters.
  */
@@ -231,55 +183,13 @@ static void pdc_old_disable_66MHz_clock(ide_hwif_t *hwif)
 
 static int config_chipset_for_dma (ide_drive_t *drive)
 {
-       struct hd_driveid *id   = drive->id;
-       ide_hwif_t *hwif        = HWIF(drive);
-       struct pci_dev *dev     = hwif->pci_dev;
-       u32 drive_conf          = 0;
-       u8 drive_pci            = 0x60 + (drive->dn << 2);
-       u8 test1 = 0, test2 = 0, speed = -1;
-       u8 AP = 0;
-
-       if (dev->device != PCI_DEVICE_ID_PROMISE_20246)
-               pdc_old_disable_66MHz_clock(drive->hwif);
+       u8 speed = ide_max_dma_mode(drive);
 
-       drive_pci = 0x60 + (drive->dn << 2);
-       pci_read_config_dword(dev, drive_pci, &drive_conf);
-       if ((drive_conf != 0x004ff304) && (drive_conf != 0x004ff3c4))
-               goto chipset_is_set;
-
-       pci_read_config_byte(dev, drive_pci, &test1);
-       if (!(test1 & SYNC_ERRDY_EN)) {
-               if (drive->select.b.unit & 0x01) {
-                       pci_read_config_byte(dev, drive_pci - 4, &test2);
-                       if ((test2 & SYNC_ERRDY_EN) &&
-                           !(test1 & SYNC_ERRDY_EN)) {
-                               pci_write_config_byte(dev, drive_pci,
-                                       test1|SYNC_ERRDY_EN);
-                       }
-               } else {
-                       pci_write_config_byte(dev, drive_pci,
-                               test1|SYNC_ERRDY_EN);
-               }
-       }
-
-chipset_is_set:
-
-       pci_read_config_byte(dev, (drive_pci), &AP);
-       if (id->capability & 4) /* IORDY_EN */
-               pci_write_config_byte(dev, (drive_pci), AP|IORDY_EN);
-       pci_read_config_byte(dev, (drive_pci), &AP);
-       if (drive->media == ide_disk)   /* PREFETCH_EN */
-               pci_write_config_byte(dev, (drive_pci), AP|PREFETCH_EN);
-
-       speed = ide_max_dma_mode(drive);
-
-       if (!(speed)) {
-               /* restore original pci-config space */
-               pci_write_config_dword(dev, drive_pci, drive_conf);
+       if (!speed)
                return 0;
-       }
 
-       (void) hwif->speedproc(drive, speed);
+       (void)pdc202xx_tune_chipset(drive, speed);
+
        return ide_dma_enable(drive);
 }