--- /dev/null
+SH7760/SH7763 integrated LCDC Framebuffer driver
+================================================
+
+0. Overwiew
+-----------
+The SH7760/SH7763 have an integrated LCD Display controller (LCDC) which
+supports (in theory) resolutions ranging from 1x1 to 1024x1024,
+with color depths ranging from 1 to 16 bits, on STN, DSTN and TFT Panels.
+
+Caveats:
+* Framebuffer memory must be a large chunk allocated at the top
+ of Area3 (HW requirement). Because of this requirement you should NOT
+ make the driver a module since at runtime it may become impossible to
+ get a large enough contiguous chunk of memory.
+
+* The driver does not support changing resolution while loaded
+ (displays aren't hotpluggable anyway)
+
+* Heavy flickering may be observed
+ a) if you're using 15/16bit color modes at >= 640x480 px resolutions,
+ b) during PCMCIA (or any other slow bus) activity.
+
+* Rotation works only 90degress clockwise, and only if horizontal
+ resolution is <= 320 pixels.
+
+files: drivers/video/sh7760fb.c
+ include/asm-sh/sh7760fb.h
+ Documentation/fb/sh7760fb.txt
+
+1. Platform setup
+-----------------
+SH7760:
+ Video data is fetched via the DMABRG DMA engine, so you have to
+ configure the SH DMAC for DMABRG mode (write 0x94808080 to the
+ DMARSRA register somewhere at boot).
+
+ PFC registers PCCR and PCDR must be set to peripheral mode.
+ (write zeros to both).
+
+The driver does NOT do the above for you since board setup is, well, job
+of the board setup code.
+
+2. Panel definitions
+--------------------
+The LCDC must explicitly be told about the type of LCD panel
+attached. Data must be wrapped in a "struct sh7760fb_platdata" and
+passed to the driver as platform_data.
+
+Suggest you take a closer look at the SH7760 Manual, Section 30.
+(http://documentation.renesas.com/eng/products/mpumcu/e602291_sh7760.pdf)
+
+The following code illustrates what needs to be done to
+get the framebuffer working on a 640x480 TFT:
+
+====================== cut here ======================================
+
+#include <linux/fb.h>
+#include <asm/sh7760fb.h>
+
+/*
+ * NEC NL6440bc26-01 640x480 TFT
+ * dotclock 25175 kHz
+ * Xres 640 Yres 480
+ * Htotal 800 Vtotal 525
+ * HsynStart 656 VsynStart 490
+ * HsynLenn 30 VsynLenn 2
+ *
+ * The linux framebuffer layer does not use the syncstart/synclen
+ * values but right/left/upper/lower margin values. The comments
+ * for the x_margin explain how to calculate those from given
+ * panel sync timings.
+ */
+static struct fb_videomode nl6448bc26 = {
+ .name = "NL6448BC26",
+ .refresh = 60,
+ .xres = 640,
+ .yres = 480,
+ .pixclock = 39683, /* in picoseconds! */
+ .hsync_len = 30,
+ .vsync_len = 2,
+ .left_margin = 114, /* HTOT - (HSYNSLEN + HSYNSTART) */
+ .right_margin = 16, /* HSYNSTART - XRES */
+ .upper_margin = 33, /* VTOT - (VSYNLEN + VSYNSTART) */
+ .lower_margin = 10, /* VSYNSTART - YRES */
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED,
+ .flag = 0,
+};
+
+static struct sh7760fb_platdata sh7760fb_nl6448 = {
+ .def_mode = &nl6448bc26,
+ .ldmtr = LDMTR_TFT_COLOR_16, /* 16bit TFT panel */
+ .lddfr = LDDFR_8BPP, /* we want 8bit output */
+ .ldpmmr = 0x0070,
+ .ldpspr = 0x0500,
+ .ldaclnr = 0,
+ .ldickr = LDICKR_CLKSRC(LCDC_CLKSRC_EXTERNAL) |
+ LDICKR_CLKDIV(1),
+ .rotate = 0,
+ .novsync = 1,
+ .blank = NULL,
+};
+
+/* SH7760:
+ * 0xFE300800: 256 * 4byte xRGB palette ram
+ * 0xFE300C00: 42 bytes ctrl registers
+ */
+static struct resource sh7760_lcdc_res[] = {
+ [0] = {
+ .start = 0xFE300800,
+ .end = 0xFE300CFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = 65,
+ .end = 65,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device sh7760_lcdc_dev = {
+ .dev = {
+ .platform_data = &sh7760fb_nl6448,
+ },
+ .name = "sh7760-lcdc",
+ .id = -1,
+ .resource = sh7760_lcdc_res,
+ .num_resources = ARRAY_SIZE(sh7760_lcdc_res),
+};
+
+====================== cut here ======================================
--- /dev/null
+/*
+ * SH7760/SH7763 LCDC Framebuffer driver.
+ *
+ * (c) 2006-2008 MSC Vertriebsges.m.b.H.,
+ * Manuel Lauss <mano@roarinelk.homelinux.net>
+ * (c) 2008 Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file COPYING in the main directory of this
+ * archive for more details.
+ *
+ * PLEASE HAVE A LOOK AT Documentation/fb/sh7760fb.txt!
+ *
+ * Thanks to Siegfried Schaefer <s.schaefer at schaefer-edv.de>
+ * for his original source and testing!
+ */
+
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/fb.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include <asm/sh7760fb.h>
+
+struct sh7760fb_par {
+ void __iomem *base;
+ int irq;
+
+ struct sh7760fb_platdata *pd; /* display information */
+
+ dma_addr_t fbdma; /* physical address */
+
+ int rot; /* rotation enabled? */
+
+ u32 pseudo_palette[16];
+
+ struct platform_device *dev;
+ struct resource *ioarea;
+ struct completion vsync; /* vsync irq event */
+};
+
+static irqreturn_t sh7760fb_irq(int irq, void *data)
+{
+ struct completion *c = data;
+
+ complete(c);
+
+ return IRQ_HANDLED;
+}
+
+static void sh7760fb_wait_vsync(struct fb_info *info)
+{
+ struct sh7760fb_par *par = info->par;
+
+ if (par->pd->novsync)
+ return;
+
+ iowrite16(ioread16(par->base + LDINTR) & ~VINT_CHECK,
+ par->base + LDINTR);
+
+ if (par->irq < 0) {
+ /* poll for vert. retrace: status bit is sticky */
+ while (!(ioread16(par->base + LDINTR) & VINT_CHECK))
+ cpu_relax();
+ } else {
+ /* a "wait_for_irq_event(par->irq)" would be extremely nice */
+ init_completion(&par->vsync);
+ enable_irq(par->irq);
+ wait_for_completion(&par->vsync);
+ disable_irq_nosync(par->irq);
+ }
+}
+
+/* wait_for_lps - wait until power supply has reached a certain state. */
+static int wait_for_lps(struct sh7760fb_par *par, int val)
+{
+ int i = 100;
+ while (--i && ((ioread16(par->base + LDPMMR) & 3) != val))
+ msleep(1);
+
+ if (i <= 0)
+ return -ETIMEDOUT;
+
+ return 0;
+}
+
+/* en/disable the LCDC */
+static int sh7760fb_blank(int blank, struct fb_info *info)
+{
+ struct sh7760fb_par *par = info->par;
+ struct sh7760fb_platdata *pd = par->pd;
+ unsigned short cntr = ioread16(par->base + LDCNTR);
+ unsigned short intr = ioread16(par->base + LDINTR);
+ int lps;
+
+ if (blank == FB_BLANK_UNBLANK) {
+ intr |= VINT_START;
+ cntr = LDCNTR_DON2 | LDCNTR_DON;
+ lps = 3;
+ } else {
+ intr &= ~VINT_START;
+ cntr = LDCNTR_DON2;
+ lps = 0;
+ }
+
+ if (pd->blank)
+ pd->blank(blank);
+
+ iowrite16(intr, par->base + LDINTR);
+ iowrite16(cntr, par->base + LDCNTR);
+
+ return wait_for_lps(par, lps);
+}
+
+/* set color registers */
+static int sh7760fb_setcmap(struct fb_cmap *cmap, struct fb_info *info)
+{
+ struct sh7760fb_par *par = info->par;
+ u32 s = cmap->start;
+ u32 l = cmap->len;
+ u16 *r = cmap->red;
+ u16 *g = cmap->green;
+ u16 *b = cmap->blue;
+ u32 col, tmo;
+ int ret;
+
+ ret = 0;
+
+ sh7760fb_wait_vsync(info);
+
+ /* request palette access */
+ iowrite16(LDPALCR_PALEN, par->base + LDPALCR);
+
+ /* poll for access grant */
+ tmo = 100;
+ while (!(ioread16(par->base + LDPALCR) & LDPALCR_PALS) && (--tmo))
+ cpu_relax();
+
+ if (!tmo) {
+ ret = 1;
+ dev_dbg(info->dev, "no palette access!\n");
+ goto out;
+ }
+
+ while (l && (s < 256)) {
+ col = ((*r) & 0xff) << 16;
+ col |= ((*g) & 0xff) << 8;
+ col |= ((*b) & 0xff);
+ col &= SH7760FB_PALETTE_MASK;
+
+ if (s < 16)
+ ((u32 *) (info->pseudo_palette))[s] = s;
+
+ s++;
+ l--;
+ r++;
+ g++;
+ b++;
+ }
+out:
+ iowrite16(0, par->base + LDPALCR);
+ return ret;
+}
+
+static void encode_fix(struct fb_fix_screeninfo *fix, struct fb_info *info,
+ unsigned long stride)
+{
+ memset(fix, 0, sizeof(struct fb_fix_screeninfo));
+ strcpy(fix->id, "sh7760-lcdc");
+
+ fix->smem_start = (unsigned long)info->screen_base;
+ fix->smem_len = info->screen_size;
+
+ fix->line_length = stride;
+}
+
+static int sh7760fb_get_color_info(struct device *dev,
+ u16 lddfr, int *bpp, int *gray)
+{
+ int lbpp, lgray;
+
+ lgray = lbpp = 0;
+
+ switch (lddfr & LDDFR_COLOR_MASK) {
+ case LDDFR_1BPP_MONO:
+ lgray = 1;
+ lbpp = 1;
+ break;
+ case LDDFR_2BPP_MONO:
+ lgray = 1;
+ lbpp = 2;
+ break;
+ case LDDFR_4BPP_MONO:
+ lgray = 1;
+ case LDDFR_4BPP:
+ lbpp = 4;
+ break;
+ case LDDFR_6BPP_MONO:
+ lgray = 1;
+ case LDDFR_8BPP:
+ lbpp = 8;
+ break;
+ case LDDFR_16BPP_RGB555:
+ case LDDFR_16BPP_RGB565:
+ lbpp = 16;
+ lgray = 0;
+ break;
+ default:
+ dev_dbg(dev, "unsupported LDDFR bit depth.\n");
+ return -EINVAL;
+ }
+
+ if (bpp)
+ *bpp = lbpp;
+ if (gray)
+ *gray = lgray;
+
+ return 0;
+}
+
+static int sh7760fb_check_var(struct fb_var_screeninfo *var,
+ struct fb_info *info)
+{
+ struct fb_fix_screeninfo *fix = &info->fix;
+ struct sh7760fb_par *par = info->par;
+ int ret, bpp;
+
+ /* get color info from register value */
+ ret = sh7760fb_get_color_info(info->dev, par->pd->lddfr, &bpp, NULL);
+ if (ret)
+ return ret;
+
+ var->bits_per_pixel = bpp;
+
+ if ((var->grayscale) && (var->bits_per_pixel == 1))
+ fix->visual = FB_VISUAL_MONO10;
+ else if (var->bits_per_pixel >= 15)
+ fix->visual = FB_VISUAL_TRUECOLOR;
+ else
+ fix->visual = FB_VISUAL_PSEUDOCOLOR;
+
+ /* TODO: add some more validation here */
+ return 0;
+}
+
+/*
+ * sh7760fb_set_par - set videomode.
+ *
+ * NOTE: The rotation, grayscale and DSTN codepaths are
+ * totally untested!
+ */
+static int sh7760fb_set_par(struct fb_info *info)
+{
+ struct sh7760fb_par *par = info->par;
+ struct fb_videomode *vm = par->pd->def_mode;
+ unsigned long sbase, dstn_off, ldsarl, stride;
+ unsigned short hsynp, hsynw, htcn, hdcn;
+ unsigned short vsynp, vsynw, vtln, vdln;
+ unsigned short lddfr, ldmtr;
+ int ret, bpp, gray;
+
+ par->rot = par->pd->rotate;
+
+ /* rotate only works with xres <= 320 */
+ if (par->rot && (vm->xres > 320)) {
+ dev_dbg(info->dev, "rotation disabled due to display size\n");
+ par->rot = 0;
+ }
+
+ /* calculate LCDC reg vals from display parameters */
+ hsynp = vm->right_margin + vm->xres;
+ hsynw = vm->hsync_len;
+ htcn = vm->left_margin + hsynp + hsynw;
+ hdcn = vm->xres;
+ vsynp = vm->lower_margin + vm->yres;
+ vsynw = vm->vsync_len;
+ vtln = vm->upper_margin + vsynp + vsynw;
+ vdln = vm->yres;
+
+ /* get color info from register value */
+ ret = sh7760fb_get_color_info(info->dev, par->pd->lddfr, &bpp, &gray);
+ if (ret)
+ return ret;
+
+ dev_dbg(info->dev, "%dx%d %dbpp %s (orientation %s)\n", hdcn,
+ vdln, bpp, gray ? "grayscale" : "color",
+ par->rot ? "rotated" : "normal");
+
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+ lddfr = par->pd->lddfr | (1 << 8);
+#else
+ lddfr = par->pd->lddfr & ~(1 << 8);
+#endif
+
+ ldmtr = par->pd->ldmtr;
+
+ if (!(vm->sync & FB_SYNC_HOR_HIGH_ACT))
+ ldmtr |= LDMTR_CL1POL;
+ if (!(vm->sync & FB_SYNC_VERT_HIGH_ACT))
+ ldmtr |= LDMTR_FLMPOL;
+
+ /* shut down LCDC before changing display parameters */
+ sh7760fb_blank(FB_BLANK_POWERDOWN, info);
+
+ iowrite16(par->pd->ldickr, par->base + LDICKR); /* pixclock */
+ iowrite16(ldmtr, par->base + LDMTR); /* polarities */
+ iowrite16(lddfr, par->base + LDDFR); /* color/depth */
+ iowrite16((par->rot ? 1 << 13 : 0), par->base + LDSMR); /* rotate */
+ iowrite16(par->pd->ldpmmr, par->base + LDPMMR); /* Power Management */
+ iowrite16(par->pd->ldpspr, par->base + LDPSPR); /* Power Supply Ctrl */
+
+ /* display resolution */
+ iowrite16(((htcn >> 3) - 1) | (((hdcn >> 3) - 1) << 8),
+ par->base + LDHCNR);
+ iowrite16(vdln - 1, par->base + LDVDLNR);
+ iowrite16(vtln - 1, par->base + LDVTLNR);
+ /* h/v sync signals */
+ iowrite16((vsynp - 1) | ((vsynw - 1) << 12), par->base + LDVSYNR);
+ iowrite16(((hsynp >> 3) - 1) | (((hsynw >> 3) - 1) << 12),
+ par->base + LDHSYNR);
+ /* AC modulation sig */
+ iowrite16(par->pd->ldaclnr, par->base + LDACLNR);
+
+ stride = (par->rot) ? vtln : hdcn;
+ if (!gray)
+ stride *= (bpp + 7) >> 3;
+ else {
+ if (bpp == 1)
+ stride >>= 3;
+ else if (bpp == 2)
+ stride >>= 2;
+ else if (bpp == 4)
+ stride >>= 1;
+ /* 6 bpp == 8 bpp */
+ }
+
+ /* if rotated, stride must be power of 2 */
+ if (par->rot) {
+ unsigned long bit = 1 << 31;
+ while (bit) {
+ if (stride & bit)
+ break;
+ bit >>= 1;
+ }
+ if (stride & ~bit)
+ stride = bit << 1; /* not P-o-2, round up */
+ }
+ iowrite16(stride, par->base + LDLAOR);
+
+ /* set display mem start address */
+ sbase = (unsigned long)par->fbdma;
+ if (par->rot)
+ sbase += (hdcn - 1) * stride;
+
+ iowrite32(sbase, par->base + LDSARU);
+
+ /*
+ * for DSTN need to set address for lower half.
+ * I (mlau) don't know which address to set it to,
+ * so I guessed at (stride * yres/2).
+ */
+ if (((ldmtr & 0x003f) >= LDMTR_DSTN_MONO_8) &&
+ ((ldmtr & 0x003f) <= LDMTR_DSTN_COLOR_16)) {
+
+ dev_dbg(info->dev, " ***** DSTN untested! *****\n");
+
+ dstn_off = stride;
+ if (par->rot)
+ dstn_off *= hdcn >> 1;
+ else
+ dstn_off *= vdln >> 1;
+
+ ldsarl = sbase + dstn_off;
+ } else
+ ldsarl = 0;
+
+ iowrite32(ldsarl, par->base + LDSARL); /* mem for lower half of DSTN */
+
+ encode_fix(&info->fix, info, stride);
+ sh7760fb_check_var(&info->var, info);
+
+ sh7760fb_blank(FB_BLANK_UNBLANK, info); /* panel on! */
+
+ dev_dbg(info->dev, "hdcn : %6d htcn : %6d\n", hdcn, htcn);
+ dev_dbg(info->dev, "hsynw : %6d hsynp : %6d\n", hsynw, hsynp);
+ dev_dbg(info->dev, "vdln : %6d vtln : %6d\n", vdln, vtln);
+ dev_dbg(info->dev, "vsynw : %6d vsynp : %6d\n", vsynw, vsynp);
+ dev_dbg(info->dev, "clksrc: %6d clkdiv: %6d\n",
+ (par->pd->ldickr >> 12) & 3, par->pd->ldickr & 0x1f);
+ dev_dbg(info->dev, "ldpmmr: 0x%04x ldpspr: 0x%04x\n", par->pd->ldpmmr,
+ par->pd->ldpspr);
+ dev_dbg(info->dev, "ldmtr : 0x%04x lddfr : 0x%04x\n", ldmtr, lddfr);
+ dev_dbg(info->dev, "ldlaor: %ld\n", stride);
+ dev_dbg(info->dev, "ldsaru: 0x%08lx ldsarl: 0x%08lx\n", sbase, ldsarl);
+
+ return 0;
+}
+
+static struct fb_ops sh7760fb_ops = {
+ .owner = THIS_MODULE,
+ .fb_blank = sh7760fb_blank,
+ .fb_check_var = sh7760fb_check_var,
+ .fb_setcmap = sh7760fb_setcmap,
+ .fb_set_par = sh7760fb_set_par,
+ .fb_fillrect = cfb_fillrect,
+ .fb_copyarea = cfb_copyarea,
+ .fb_imageblit = cfb_imageblit,
+};
+
+static void sh7760fb_free_mem(struct fb_info *info)
+{
+ struct sh7760fb_par *par = info->par;
+
+ if (!info->screen_base)
+ return;
+
+ dma_free_coherent(info->dev, info->screen_size,
+ info->screen_base, par->fbdma);
+
+ par->fbdma = 0;
+ info->screen_base = NULL;
+ info->screen_size = 0;
+}
+
+/* allocate the framebuffer memory. This memory must be in Area3,
+ * (dictated by the DMA engine) and contiguous, at a 512 byte boundary.
+ */
+static int sh7760fb_alloc_mem(struct fb_info *info)
+{
+ struct sh7760fb_par *par = info->par;
+ void *fbmem;
+ unsigned long vram;
+ int ret, bpp;
+
+ if (info->screen_base)
+ return 0;
+
+ /* get color info from register value */
+ ret = sh7760fb_get_color_info(info->dev, par->pd->lddfr, &bpp, NULL);
+ if (ret) {
+ printk(KERN_ERR "colinfo\n");
+ return ret;
+ }
+
+ /* min VRAM: xres_min = 16, yres_min = 1, bpp = 1: 2byte -> 1 page
+ max VRAM: xres_max = 1024, yres_max = 1024, bpp = 16: 2MB */
+
+ vram = info->var.xres * info->var.yres;
+ if (info->var.grayscale) {
+ if (bpp == 1)
+ vram >>= 3;
+ else if (bpp == 2)
+ vram >>= 2;
+ else if (bpp == 4)
+ vram >>= 1;
+ } else if (bpp > 8)
+ vram *= 2;
+ if ((vram < 1) || (vram > 1024 * 2048)) {
+ dev_dbg(info->dev, "too much VRAM required. Check settings\n");
+ return -ENODEV;
+ }
+
+ if (vram < PAGE_SIZE)
+ vram = PAGE_SIZE;
+
+ fbmem = dma_alloc_coherent(info->dev, vram, &par->fbdma, GFP_KERNEL);
+
+ if (!fbmem)
+ return -ENOMEM;
+
+ if ((par->fbdma & SH7760FB_DMA_MASK) != SH7760FB_DMA_MASK) {
+ sh7760fb_free_mem(info);
+ dev_err(info->dev, "kernel gave me memory at 0x%08lx, which is"
+ "unusable for the LCDC\n", (unsigned long)par->fbdma);
+ return -ENOMEM;
+ }
+
+ info->screen_base = fbmem;
+ info->screen_size = vram;
+
+ return 0;
+}
+
+static int __devinit sh7760fb_probe(struct platform_device *pdev)
+{
+ struct fb_info *info;
+ struct resource *res;
+ struct sh7760fb_par *par;
+ int ret;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (unlikely(res == NULL)) {
+ dev_err(&pdev->dev, "invalid resource\n");
+ return -EINVAL;
+ }
+
+ info = framebuffer_alloc(sizeof(struct sh7760fb_par), &pdev->dev);
+ if (!info)
+ return -ENOMEM;
+
+ par = info->par;
+ par->dev = pdev;
+
+ par->pd = pdev->dev.platform_data;
+ if (!par->pd) {
+ dev_dbg(info->dev, "no display setup data!\n");
+ ret = -ENODEV;
+ goto out_fb;
+ }
+
+ par->ioarea = request_mem_region(res->start,
+ (res->end - res->start), pdev->name);
+ if (!par->ioarea) {
+ dev_err(&pdev->dev, "mmio area busy\n");
+ ret = -EBUSY;
+ goto out_fb;
+ }
+
+ par->base = ioremap_nocache(res->start, res->end - res->start + 1);
+ if (!par->base) {
+ dev_err(&pdev->dev, "cannot remap\n");
+ ret = -ENODEV;
+ goto out_res;
+ }
+
+ iowrite16(0, par->base + LDINTR); /* disable vsync irq */
+ par->irq = platform_get_irq(pdev, 0);
+ if (par->irq >= 0) {
+ ret = request_irq(par->irq, sh7760fb_irq, 0,
+ "sh7760-lcdc", &par->vsync);
+ if (ret) {
+ dev_err(&pdev->dev, "cannot grab IRQ\n");
+ par->irq = -ENXIO;
+ } else
+ disable_irq_nosync(par->irq);
+ }
+
+ fb_videomode_to_var(&info->var, par->pd->def_mode);
+
+ ret = sh7760fb_alloc_mem(info);
+ if (ret) {
+ dev_dbg(info->dev, "framebuffer memory allocation failed!\n");
+ goto out_unmap;
+ }
+
+ info->pseudo_palette = par->pseudo_palette;
+
+ /* fixup color register bitpositions. These are fixed by hardware */
+ info->var.red.offset = 11;
+ info->var.red.length = 5;
+ info->var.red.msb_right = 0;
+
+ info->var.green.offset = 5;
+ info->var.green.length = 6;
+ info->var.green.msb_right = 0;
+
+ info->var.blue.offset = 0;
+ info->var.blue.length = 5;
+ info->var.blue.msb_right = 0;
+
+ info->var.transp.offset = 0;
+ info->var.transp.length = 0;
+ info->var.transp.msb_right = 0;
+
+ /* set the DON2 bit now, before cmap allocation, as it will randomize
+ * palette memory.
+ */
+ iowrite16(LDCNTR_DON2, par->base + LDCNTR);
+ info->fbops = &sh7760fb_ops;
+
+ ret = fb_alloc_cmap(&info->cmap, 256, 0);
+ if (ret) {
+ dev_dbg(info->dev, "Unable to allocate cmap memory\n");
+ goto out_mem;
+ }
+
+ ret = register_framebuffer(info);
+ if (ret < 0) {
+ dev_dbg(info->dev, "cannot register fb!\n");
+ goto out_cmap;
+ }
+ platform_set_drvdata(pdev, info);
+
+ printk(KERN_INFO "%s: memory at phys 0x%08lx-0x%08lx, size %ld KiB\n",
+ pdev->name,
+ (unsigned long)par->fbdma,
+ (unsigned long)(par->fbdma + info->screen_size - 1),
+ info->screen_size >> 10);
+
+ return 0;
+
+out_cmap:
+ sh7760fb_blank(FB_BLANK_POWERDOWN, info);
+ fb_dealloc_cmap(&info->cmap);
+out_mem:
+ sh7760fb_free_mem(info);
+out_unmap:
+ if (par->irq >= 0)
+ free_irq(par->irq, &par->vsync);
+ iounmap(par->base);
+out_res:
+ release_resource(par->ioarea);
+ kfree(par->ioarea);
+out_fb:
+ framebuffer_release(info);
+ return ret;
+}
+
+static int __devexit sh7760fb_remove(struct platform_device *dev)
+{
+ struct fb_info *info = platform_get_drvdata(dev);
+ struct sh7760fb_par *par = info->par;
+
+ sh7760fb_blank(FB_BLANK_POWERDOWN, info);
+ unregister_framebuffer(info);
+ fb_dealloc_cmap(&info->cmap);
+ sh7760fb_free_mem(info);
+ if (par->irq >= 0)
+ free_irq(par->irq, par);
+ iounmap(par->base);
+ release_resource(par->ioarea);
+ kfree(par->ioarea);
+ framebuffer_release(info);
+ platform_set_drvdata(dev, NULL);
+
+ return 0;
+}
+
+static struct platform_driver sh7760_lcdc_driver = {
+ .driver = {
+ .name = "sh7760-lcdc",
+ .owner = THIS_MODULE,
+ },
+ .probe = sh7760fb_probe,
+ .remove = __devexit_p(sh7760fb_remove),
+};
+
+static int __init sh7760fb_init(void)
+{
+ return platform_driver_register(&sh7760_lcdc_driver);
+}
+
+static void __exit sh7760fb_exit(void)
+{
+ platform_driver_unregister(&sh7760_lcdc_driver);
+}
+
+module_init(sh7760fb_init);
+module_exit(sh7760fb_exit);
+
+MODULE_AUTHOR("Nobuhiro Iwamatsu, Manuel Lauss");
+MODULE_DESCRIPTION("FBdev for SH7760/63 integrated LCD Controller");
+MODULE_LICENSE("GPL");
--- /dev/null
+/*
+ * sh7760fb.h -- platform data for SH7760/SH7763 LCDC framebuffer driver.
+ *
+ * (c) 2006-2008 MSC Vertriebsges.m.b.H.,
+ * Manuel Lauss <mano@roarinelk.homelinux.net>
+ * (c) 2008 Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
+ */
+
+#ifndef _ASM_SH_SH7760FB_H
+#define _ASM_SH_SH7760FB_H
+
+/*
+ * some bits of the colormap registers should be written as zero.
+ * create a mask for that.
+ */
+#define SH7760FB_PALETTE_MASK 0x00f8fcf8
+
+/* The LCDC dma engine always sets bits 27-26 to 1: this is Area3 */
+#define SH7760FB_DMA_MASK 0x0C000000
+
+/* palette */
+#define LDPR(x) (((x) << 2))
+
+/* framebuffer registers and bits */
+#define LDICKR 0x400
+#define LDMTR 0x402
+/* see sh7760fb.h for LDMTR bits */
+#define LDDFR 0x404
+#define LDDFR_PABD (1 << 8)
+#define LDDFR_COLOR_MASK 0x7F
+#define LDSMR 0x406
+#define LDSMR_ROT (1 << 13)
+#define LDSARU 0x408
+#define LDSARL 0x40c
+#define LDLAOR 0x410
+#define LDPALCR 0x412
+#define LDPALCR_PALS (1 << 4)
+#define LDPALCR_PALEN (1 << 0)
+#define LDHCNR 0x414
+#define LDHSYNR 0x416
+#define LDVDLNR 0x418
+#define LDVTLNR 0x41a
+#define LDVSYNR 0x41c
+#define LDACLNR 0x41e
+#define LDINTR 0x420
+#define LDPMMR 0x424
+#define LDPSPR 0x426
+#define LDCNTR 0x428
+#define LDCNTR_DON (1 << 0)
+#define LDCNTR_DON2 (1 << 4)
+
+#ifdef CONFIG_CPU_SUBTYPE_SH7763
+# define LDLIRNR 0x440
+/* LDINTR bit */
+# define LDINTR_MINTEN (1 << 15)
+# define LDINTR_FINTEN (1 << 14)
+# define LDINTR_VSINTEN (1 << 13)
+# define LDINTR_VEINTEN (1 << 12)
+# define LDINTR_MINTS (1 << 11)
+# define LDINTR_FINTS (1 << 10)
+# define LDINTR_VSINTS (1 << 9)
+# define LDINTR_VEINTS (1 << 8)
+# define VINT_START (LDINTR_VSINTEN)
+# define VINT_CHECK (LDINTR_VSINTS)
+#else
+/* LDINTR bit */
+# define LDINTR_VINTSEL (1 << 12)
+# define LDINTR_VINTE (1 << 8)
+# define LDINTR_VINTS (1 << 0)
+# define VINT_START (LDINTR_VINTSEL)
+# define VINT_CHECK (LDINTR_VINTS)
+#endif
+
+/* HSYNC polarity inversion */
+#define LDMTR_FLMPOL (1 << 15)
+
+/* VSYNC polarity inversion */
+#define LDMTR_CL1POL (1 << 14)
+
+/* DISPLAY-ENABLE polarity inversion */
+#define LDMTR_DISPEN_LOWACT (1 << 13)
+
+/* DISPLAY DATA BUS polarity inversion */
+#define LDMTR_DPOL_LOWACT (1 << 12)
+
+/* AC modulation signal enable */
+#define LDMTR_MCNT (1 << 10)
+
+/* Disable output of HSYNC during VSYNC period */
+#define LDMTR_CL1CNT (1 << 9)
+
+/* Disable output of VSYNC during VSYNC period */
+#define LDMTR_CL2CNT (1 << 8)
+
+/* Display types supported by the LCDC */
+#define LDMTR_STN_MONO_4 0x00
+#define LDMTR_STN_MONO_8 0x01
+#define LDMTR_STN_COLOR_4 0x08
+#define LDMTR_STN_COLOR_8 0x09
+#define LDMTR_STN_COLOR_12 0x0A
+#define LDMTR_STN_COLOR_16 0x0B
+#define LDMTR_DSTN_MONO_8 0x11
+#define LDMTR_DSTN_MONO_16 0x13
+#define LDMTR_DSTN_COLOR_8 0x19
+#define LDMTR_DSTN_COLOR_12 0x1A
+#define LDMTR_DSTN_COLOR_16 0x1B
+#define LDMTR_TFT_COLOR_16 0x2B
+
+/* framebuffer color layout */
+#define LDDFR_1BPP_MONO 0x00
+#define LDDFR_2BPP_MONO 0x01
+#define LDDFR_4BPP_MONO 0x02
+#define LDDFR_6BPP_MONO 0x04
+#define LDDFR_4BPP 0x0A
+#define LDDFR_8BPP 0x0C
+#define LDDFR_16BPP_RGB555 0x1D
+#define LDDFR_16BPP_RGB565 0x2D
+
+/* LCDC Pixclock sources */
+#define LCDC_CLKSRC_BUSCLOCK 0
+#define LCDC_CLKSRC_PERIPHERAL 1
+#define LCDC_CLKSRC_EXTERNAL 2
+
+#define LDICKR_CLKSRC(x) \
+ (((x) & 3) << 12)
+
+/* LCDC pixclock input divider. Set to 1 at a minimum! */
+#define LDICKR_CLKDIV(x) \
+ ((x) & 0x1f)
+
+struct sh7760fb_platdata {
+
+ /* Set this member to a valid fb_videmode for the display you
+ * wish to use. The following members must be initialized:
+ * xres, yres, hsync_len, vsync_len, sync,
+ * {left,right,upper,lower}_margin.
+ * The driver uses the above members to calculate register values
+ * and memory requirements. Other members are ignored but may
+ * be used by other framebuffer layer components.
+ */
+ struct fb_videomode *def_mode;
+
+ /* LDMTR includes display type and signal polarity. The
+ * HSYNC/VSYNC polarities are derived from the fb_var_screeninfo
+ * data above; however the polarities of the following signals
+ * must be encoded in the ldmtr member:
+ * Display Enable signal (default high-active) DISPEN_LOWACT
+ * Display Data signals (default high-active) DPOL_LOWACT
+ * AC Modulation signal (default off) MCNT
+ * Hsync-During-Vsync suppression (default off) CL1CNT
+ * Vsync-during-vsync suppression (default off) CL2CNT
+ * NOTE: also set a display type!
+ * (one of LDMTR_{STN,DSTN,TFT}_{MONO,COLOR}_{4,8,12,16})
+ */
+ u16 ldmtr;
+
+ /* LDDFR controls framebuffer image format (depth, organization)
+ * Use ONE of the LDDFR_?BPP_* macros!
+ */
+ u16 lddfr;
+
+ /* LDPMMR and LDPSPR control the timing of the power signals
+ * for the display. Please read the SH7760 Hardware Manual,
+ * Chapters 30.3.17, 30.3.18 and 30.4.6!
+ */
+ u16 ldpmmr;
+ u16 ldpspr;
+
+ /* LDACLNR contains the line numbers after which the AC modulation
+ * signal is to toggle. Set to ZERO for TFTs or displays which
+ * do not need it. (Chapter 30.3.15 in SH7760 Hardware Manual).
+ */
+ u16 ldaclnr;
+
+ /* LDICKR contains information on pixelclock source and config.
+ * Please use the LDICKR_CLKSRC() and LDICKR_CLKDIV() macros.
+ * minimal value for CLKDIV() must be 1!.
+ */
+ u16 ldickr;
+
+ /* set this member to 1 if you wish to use the LCDC's hardware
+ * rotation function. This is limited to displays <= 320x200
+ * pixels resolution!
+ */
+ int rotate; /* set to 1 to rotate 90 CCW */
+
+ /* set this to 1 to suppress vsync irq use. */
+ int novsync;
+
+ /* blanking hook for platform. Set this if your platform can do
+ * more than the LCDC in terms of blanking (e.g. disable clock
+ * generator / backlight power supply / etc.
+ */
+ void (*blank) (int);
+};
+
+#endif /* _ASM_SH_SH7760FB_H */
projects / linux-2.6-omap-h63xx.git / commitdiff