Blackfin arch: AD7879 Touchscreen driver

Add AD7879 Touchscreen driver to the device structures

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>

diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index ccfa088018407845d37ef317506bbd82eabe3907..dc5a30849c1515443471eb07fae9940c366a7b6f 100644 (file)
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -51,7 +51,6 @@
 #include <asm/reboot.h>
 #include <asm/portmux.h>
 #include <asm/dpmc.h>
-#include <linux/spi/ad7877.h>
 
 /*
  * Name the Board for the /proc/cpuinfo
@@ -555,6 +554,7 @@ static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
 #endif
 
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+#include <linux/spi/ad7877.h>
 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
        .enable_dma = 0,
        .bits_per_word = 16,
@@ -575,6 +575,28 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 };
 #endif
 
+#if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#include <linux/spi/ad7879.h>
+static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
+       .enable_dma = 0,
+       .bits_per_word = 16,
+};
+
+static const struct ad7879_platform_data bfin_ad7879_ts_info = {
+       .model                  = 7879, /* Model = AD7879 */
+       .x_plate_ohms           = 620,  /* 620 Ohm from the touch datasheet */
+       .pressure_max           = 10000,
+       .pressure_min           = 0,
+       .first_conversion_delay = 3,    /* wait 512us before do a first conversion */
+       .acquisition_time       = 1,    /* 4us acquisition time per sample */
+       .median                 = 2,    /* do 8 measurements */
+       .averaging              = 1,    /* take the average of 4 middle samples */
+       .pen_down_acc_interval  = 255,  /* 9.4 ms */
+       .gpio_output            = 1,    /* configure AUX/VBAT/GPIO as GPIO output */
+       .gpio_default           = 1,    /* During initialization set GPIO = HIGH */
+};
+#endif
+
 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 static struct bfin5xx_spi_chip spidev_chip_info = {
        .enable_dma = 0,
@@ -728,6 +750,18 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .controller_data = &spi_ad7877_chip_info,
        },
 #endif
+#if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+       {
+               .modalias = "ad7879",
+               .platform_data = &bfin_ad7879_ts_info,
+               .irq = IRQ_PF7,
+               .max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
+               .bus_num = 0,
+               .chip_select = 1,
+               .controller_data = &spi_ad7879_chip_info,
+               .mode = SPI_CPHA | SPI_CPOL,
+       },
+#endif
 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
        {
                .modalias = "spidev",
@@ -742,7 +776,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .modalias = "bfin-lq035q1-spi",
                .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
                .bus_num = 0,
-               .chip_select = 1,
+               .chip_select = 2,
                .controller_data = &lq035q1_spi_chip_info,
                .mode = SPI_CPHA | SPI_CPOL,
        },
@@ -799,7 +833,7 @@ static struct platform_device bfin_fb_adv7393_device = {
 
 static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
        .mode =         LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
-       .use_bl =       1,
+       .use_bl =       0,      /* let something else control the LCD Blacklight */
        .gpio_bl =      GPIO_PF7,
 };