* Stuart Lynne <sl@lineo.com>, Tom Rushworth <tbr@lineo.com>
*/
-/*
- * The encapsultaion is designed to overcome difficulties with some USB hardware.
+/*
+ * The encapsultaion is designed to overcome difficulties with some USB
+ * hardware.
*
* While the USB protocol has a CRC over the data while in transit, i.e. while
- * being carried over the bus, there is no end to end protection. If the hardware
- * has any problems getting the data into or out of the USB transmit and receive
- * FIFO's then data can be lost.
+ * being carried over the bus, there is no end to end protection. If the
+ * hardware has any problems getting the data into or out of the USB transmit
+ * and receive FIFO's then data can be lost.
*
- * This protocol adds a two byte trailer to each USB packet to specify the number
- * of bytes of valid data and a 10 bit CRC that will allow the receiver to verify
- * that the entire USB packet was received without error.
+ * This protocol adds a two byte trailer to each USB packet to specify the
+ * number of bytes of valid data and a 10 bit CRC that will allow the receiver
+ * to verify that the entire USB packet was received without error.
*
- * Because in this case the sender and receiver are the class and function drivers
- * there is now end to end protection.
+ * Because in this case the sender and receiver are the class and function
+ * drivers there is now end to end protection.
*
- * There is an additional option that can be used to force all transmitted packets
- * to be padded to the maximum packet size. This provides a work around for some
- * devices which have problems with small USB packets.
+ * There is an additional option that can be used to force all transmitted
+ * packets to be padded to the maximum packet size. This provides a work
+ * around for some devices which have problems with small USB packets.
*
* Assuming a packetsize of N:
*
* | Data Length | 10 bit CRC |
* + 7 . 6 . 5 . 4 . 3 . 2 . 1 . 0 | 7 . 6 . 5 . 4 . 3 . 2 . 1 . 0 +
*
- * The 10 bit CRC is computed across the sent data, followed by the trailer with
- * the length set and the CRC set to zero. The CRC is then OR'd into the trailer.
+ * The 10 bit CRC is computed across the sent data, followed by the trailer
+ * with the length set and the CRC set to zero. The CRC is then OR'd into
+ * the trailer.
*
- * When received a 10 bit CRC is computed over the entire frame including the trailer
- * and should be equal to zero.
+ * When received a 10 bit CRC is computed over the entire frame including
+ * the trailer and should be equal to zero.
*
* Two module parameters are used to control the encapsulation, if both are
* turned of the module works as a simple serial device with NO
#include <linux/tty_flip.h>
#include <linux/module.h>
#include <linux/spinlock.h>
-#include <asm/uaccess.h>
+#include <linux/uaccess.h>
#include <linux/usb.h>
#include <linux/usb/serial.h>
#define DRIVER_AUTHOR "sl@lineo.com, tbr@lineo.com"
#define DRIVER_DESC "USB Safe Encapsulated Serial"
-MODULE_AUTHOR (DRIVER_AUTHOR);
-MODULE_DESCRIPTION (DRIVER_DESC);
+MODULE_AUTHOR(DRIVER_AUTHOR);
+MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_LICENSE("GPL");
-static __u16 vendor; // no default
-static __u16 product; // no default
+static __u16 vendor; /* no default */
+static __u16 product; /* no default */
module_param(vendor, ushort, 0);
MODULE_PARM_DESC(vendor, "User specified USB idVendor (required)");
module_param(product, ushort, 0);
#define LINEO_SAFESERIAL_CRC_PADDED 0x02
-#define MY_USB_DEVICE(vend,prod,dc,ic,isc) \
- .match_flags = USB_DEVICE_ID_MATCH_DEVICE | USB_DEVICE_ID_MATCH_DEV_CLASS | \
- USB_DEVICE_ID_MATCH_INT_CLASS | USB_DEVICE_ID_MATCH_INT_SUBCLASS, \
- .idVendor = (vend), \
- .idProduct = (prod),\
- .bDeviceClass = (dc),\
- .bInterfaceClass = (ic), \
- .bInterfaceSubClass = (isc),
+#define MY_USB_DEVICE(vend, prod, dc, ic, isc) \
+ .match_flags = USB_DEVICE_ID_MATCH_DEVICE | \
+ USB_DEVICE_ID_MATCH_DEV_CLASS | \
+ USB_DEVICE_ID_MATCH_INT_CLASS | \
+ USB_DEVICE_ID_MATCH_INT_SUBCLASS, \
+ .idVendor = (vend), \
+ .idProduct = (prod),\
+ .bDeviceClass = (dc),\
+ .bInterfaceClass = (ic), \
+ .bInterfaceSubClass = (isc),
static struct usb_device_id id_table[] = {
- {MY_USB_DEVICE (0x49f, 0xffff, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, // Itsy
- {MY_USB_DEVICE (0x3f0, 0x2101, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, // Calypso
- {MY_USB_DEVICE (0x4dd, 0x8001, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, // Iris
- {MY_USB_DEVICE (0x4dd, 0x8002, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, // Collie
- {MY_USB_DEVICE (0x4dd, 0x8003, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, // Collie
- {MY_USB_DEVICE (0x4dd, 0x8004, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, // Collie
- {MY_USB_DEVICE (0x5f9, 0xffff, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, // Sharp tmp
- // extra null entry for module
- // vendor/produc parameters
- {MY_USB_DEVICE (0, 0, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)},
- {} // terminating entry
+ {MY_USB_DEVICE(0x49f, 0xffff, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, /* Itsy */
+ {MY_USB_DEVICE(0x3f0, 0x2101, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, /* Calypso */
+ {MY_USB_DEVICE(0x4dd, 0x8001, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, /* Iris */
+ {MY_USB_DEVICE(0x4dd, 0x8002, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, /* Collie */
+ {MY_USB_DEVICE(0x4dd, 0x8003, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, /* Collie */
+ {MY_USB_DEVICE(0x4dd, 0x8004, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, /* Collie */
+ {MY_USB_DEVICE(0x5f9, 0xffff, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, /* Sharp tmp */
+ /* extra null entry for module vendor/produc parameters */
+ {MY_USB_DEVICE(0, 0, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)},
+ {} /* terminating entry */
};
-MODULE_DEVICE_TABLE (usb, id_table);
+MODULE_DEVICE_TABLE(usb, id_table);
static struct usb_driver safe_driver = {
.name = "safe_serial",
};
static const __u16 crc10_table[256] = {
- 0x000, 0x233, 0x255, 0x066, 0x299, 0x0aa, 0x0cc, 0x2ff, 0x301, 0x132, 0x154, 0x367, 0x198, 0x3ab, 0x3cd, 0x1fe,
- 0x031, 0x202, 0x264, 0x057, 0x2a8, 0x09b, 0x0fd, 0x2ce, 0x330, 0x103, 0x165, 0x356, 0x1a9, 0x39a, 0x3fc, 0x1cf,
- 0x062, 0x251, 0x237, 0x004, 0x2fb, 0x0c8, 0x0ae, 0x29d, 0x363, 0x150, 0x136, 0x305, 0x1fa, 0x3c9, 0x3af, 0x19c,
- 0x053, 0x260, 0x206, 0x035, 0x2ca, 0x0f9, 0x09f, 0x2ac, 0x352, 0x161, 0x107, 0x334, 0x1cb, 0x3f8, 0x39e, 0x1ad,
- 0x0c4, 0x2f7, 0x291, 0x0a2, 0x25d, 0x06e, 0x008, 0x23b, 0x3c5, 0x1f6, 0x190, 0x3a3, 0x15c, 0x36f, 0x309, 0x13a,
- 0x0f5, 0x2c6, 0x2a0, 0x093, 0x26c, 0x05f, 0x039, 0x20a, 0x3f4, 0x1c7, 0x1a1, 0x392, 0x16d, 0x35e, 0x338, 0x10b,
- 0x0a6, 0x295, 0x2f3, 0x0c0, 0x23f, 0x00c, 0x06a, 0x259, 0x3a7, 0x194, 0x1f2, 0x3c1, 0x13e, 0x30d, 0x36b, 0x158,
- 0x097, 0x2a4, 0x2c2, 0x0f1, 0x20e, 0x03d, 0x05b, 0x268, 0x396, 0x1a5, 0x1c3, 0x3f0, 0x10f, 0x33c, 0x35a, 0x169,
- 0x188, 0x3bb, 0x3dd, 0x1ee, 0x311, 0x122, 0x144, 0x377, 0x289, 0x0ba, 0x0dc, 0x2ef, 0x010, 0x223, 0x245, 0x076,
- 0x1b9, 0x38a, 0x3ec, 0x1df, 0x320, 0x113, 0x175, 0x346, 0x2b8, 0x08b, 0x0ed, 0x2de, 0x021, 0x212, 0x274, 0x047,
- 0x1ea, 0x3d9, 0x3bf, 0x18c, 0x373, 0x140, 0x126, 0x315, 0x2eb, 0x0d8, 0x0be, 0x28d, 0x072, 0x241, 0x227, 0x014,
- 0x1db, 0x3e8, 0x38e, 0x1bd, 0x342, 0x171, 0x117, 0x324, 0x2da, 0x0e9, 0x08f, 0x2bc, 0x043, 0x270, 0x216, 0x025,
- 0x14c, 0x37f, 0x319, 0x12a, 0x3d5, 0x1e6, 0x180, 0x3b3, 0x24d, 0x07e, 0x018, 0x22b, 0x0d4, 0x2e7, 0x281, 0x0b2,
- 0x17d, 0x34e, 0x328, 0x11b, 0x3e4, 0x1d7, 0x1b1, 0x382, 0x27c, 0x04f, 0x029, 0x21a, 0x0e5, 0x2d6, 0x2b0, 0x083,
- 0x12e, 0x31d, 0x37b, 0x148, 0x3b7, 0x184, 0x1e2, 0x3d1, 0x22f, 0x01c, 0x07a, 0x249, 0x0b6, 0x285, 0x2e3, 0x0d0,
- 0x11f, 0x32c, 0x34a, 0x179, 0x386, 0x1b5, 0x1d3, 0x3e0, 0x21e, 0x02d, 0x04b, 0x278, 0x087, 0x2b4, 0x2d2, 0x0e1,
+ 0x000, 0x233, 0x255, 0x066, 0x299, 0x0aa, 0x0cc, 0x2ff,
+ 0x301, 0x132, 0x154, 0x367, 0x198, 0x3ab, 0x3cd, 0x1fe,
+ 0x031, 0x202, 0x264, 0x057, 0x2a8, 0x09b, 0x0fd, 0x2ce,
+ 0x330, 0x103, 0x165, 0x356, 0x1a9, 0x39a, 0x3fc, 0x1cf,
+ 0x062, 0x251, 0x237, 0x004, 0x2fb, 0x0c8, 0x0ae, 0x29d,
+ 0x363, 0x150, 0x136, 0x305, 0x1fa, 0x3c9, 0x3af, 0x19c,
+ 0x053, 0x260, 0x206, 0x035, 0x2ca, 0x0f9, 0x09f, 0x2ac,
+ 0x352, 0x161, 0x107, 0x334, 0x1cb, 0x3f8, 0x39e, 0x1ad,
+ 0x0c4, 0x2f7, 0x291, 0x0a2, 0x25d, 0x06e, 0x008, 0x23b,
+ 0x3c5, 0x1f6, 0x190, 0x3a3, 0x15c, 0x36f, 0x309, 0x13a,
+ 0x0f5, 0x2c6, 0x2a0, 0x093, 0x26c, 0x05f, 0x039, 0x20a,
+ 0x3f4, 0x1c7, 0x1a1, 0x392, 0x16d, 0x35e, 0x338, 0x10b,
+ 0x0a6, 0x295, 0x2f3, 0x0c0, 0x23f, 0x00c, 0x06a, 0x259,
+ 0x3a7, 0x194, 0x1f2, 0x3c1, 0x13e, 0x30d, 0x36b, 0x158,
+ 0x097, 0x2a4, 0x2c2, 0x0f1, 0x20e, 0x03d, 0x05b, 0x268,
+ 0x396, 0x1a5, 0x1c3, 0x3f0, 0x10f, 0x33c, 0x35a, 0x169,
+ 0x188, 0x3bb, 0x3dd, 0x1ee, 0x311, 0x122, 0x144, 0x377,
+ 0x289, 0x0ba, 0x0dc, 0x2ef, 0x010, 0x223, 0x245, 0x076,
+ 0x1b9, 0x38a, 0x3ec, 0x1df, 0x320, 0x113, 0x175, 0x346,
+ 0x2b8, 0x08b, 0x0ed, 0x2de, 0x021, 0x212, 0x274, 0x047,
+ 0x1ea, 0x3d9, 0x3bf, 0x18c, 0x373, 0x140, 0x126, 0x315,
+ 0x2eb, 0x0d8, 0x0be, 0x28d, 0x072, 0x241, 0x227, 0x014,
+ 0x1db, 0x3e8, 0x38e, 0x1bd, 0x342, 0x171, 0x117, 0x324,
+ 0x2da, 0x0e9, 0x08f, 0x2bc, 0x043, 0x270, 0x216, 0x025,
+ 0x14c, 0x37f, 0x319, 0x12a, 0x3d5, 0x1e6, 0x180, 0x3b3,
+ 0x24d, 0x07e, 0x018, 0x22b, 0x0d4, 0x2e7, 0x281, 0x0b2,
+ 0x17d, 0x34e, 0x328, 0x11b, 0x3e4, 0x1d7, 0x1b1, 0x382,
+ 0x27c, 0x04f, 0x029, 0x21a, 0x0e5, 0x2d6, 0x2b0, 0x083,
+ 0x12e, 0x31d, 0x37b, 0x148, 0x3b7, 0x184, 0x1e2, 0x3d1,
+ 0x22f, 0x01c, 0x07a, 0x249, 0x0b6, 0x285, 0x2e3, 0x0d0,
+ 0x11f, 0x32c, 0x34a, 0x179, 0x386, 0x1b5, 0x1d3, 0x3e0,
+ 0x21e, 0x02d, 0x04b, 0x278, 0x087, 0x2b4, 0x2d2, 0x0e1,
};
-#define CRC10_INITFCS 0x000 // Initial FCS value
-#define CRC10_GOODFCS 0x000 // Good final FCS value
-#define CRC10_FCS(fcs, c) ( (((fcs) << 8) & 0x3ff) ^ crc10_table[((fcs) >> 2) & 0xff] ^ (c))
+#define CRC10_INITFCS 0x000 /* Initial FCS value */
+#define CRC10_GOODFCS 0x000 /* Good final FCS value */
+#define CRC10_FCS(fcs, c) ((((fcs) << 8) & 0x3ff) ^ crc10_table[((fcs) >> 2) & 0xff] ^ (c))
-/**
+/**
* fcs_compute10 - memcpy and calculate 10 bit CRC across buffer
* @sp: pointer to buffer
* @len: number of bytes
* Perform a memcpy and calculate fcs using ppp 10bit CRC algorithm. Return
* new 10 bit FCS.
*/
-static __u16 __inline__ fcs_compute10 (unsigned char *sp, int len, __u16 fcs)
+static __u16 __inline__ fcs_compute10(unsigned char *sp, int len, __u16 fcs)
{
- for (; len-- > 0; fcs = CRC10_FCS (fcs, *sp++));
+ for (; len-- > 0; fcs = CRC10_FCS(fcs, *sp++));
return fcs;
}
-static void safe_read_bulk_callback (struct urb *urb)
+static void safe_read_bulk_callback(struct urb *urb)
{
struct usb_serial_port *port = urb->context;
unsigned char *data = urb->transfer_buffer;
int result;
int status = urb->status;
- dbg ("%s", __func__);
+ dbg("%s", __func__);
if (status) {
dbg("%s - nonzero read bulk status received: %d",
return;
}
- dbg ("safe_read_bulk_callback length: %d", port->read_urb->actual_length);
+ dbg("safe_read_bulk_callback length: %d",
+ port->read_urb->actual_length);
#ifdef ECHO_RCV
{
int i;
unsigned char *cp = port->read_urb->transfer_buffer;
for (i = 0; i < port->read_urb->actual_length; i++) {
- if ((i % 32) == 0) {
- printk ("\nru[%02x] ", i);
- }
- printk ("%02x ", *cp++);
+ if ((i % 32) == 0)
+ printk("\nru[%02x] ", i);
+ printk("%02x ", *cp++);
}
- printk ("\n");
+ printk("\n");
}
#endif
if (safe) {
__u16 fcs;
- if (!(fcs = fcs_compute10 (data, length, CRC10_INITFCS))) {
+ fcs = fcs_compute10(data, length, CRC10_INITFCS);
+ if (!fcs) {
int actual_length = data[length - 2] >> 2;
if (actual_length <= (length - 2)) {
- info ("%s - actual: %d", __func__, actual_length);
- tty_insert_flip_string(port->port.tty, data, actual_length);
- tty_flip_buffer_push (port->port.tty);
+ info("%s - actual: %d", __func__,
+ actual_length);
+ tty_insert_flip_string(port->port.tty,
+ data, actual_length);
+ tty_flip_buffer_push(port->port.tty);
} else {
- err ("%s - inconsistent lengths %d:%d", __func__,
- actual_length, length);
+ err("%s - inconsistent lengths %d:%d",
+ __func__, actual_length, length);
}
} else {
- err ("%s - bad CRC %x", __func__, fcs);
+ err("%s - bad CRC %x", __func__, fcs);
}
} else {
tty_insert_flip_string(port->port.tty, data, length);
- tty_flip_buffer_push (port->port.tty);
+ tty_flip_buffer_push(port->port.tty);
}
/* Continue trying to always read */
- usb_fill_bulk_urb (urb, port->serial->dev,
- usb_rcvbulkpipe (port->serial->dev, port->bulk_in_endpointAddress),
- urb->transfer_buffer, urb->transfer_buffer_length,
- safe_read_bulk_callback, port);
-
- if ((result = usb_submit_urb (urb, GFP_ATOMIC))) {
- err ("%s - failed resubmitting read urb, error %d", __func__, result);
+ usb_fill_bulk_urb(urb, port->serial->dev,
+ usb_rcvbulkpipe(port->serial->dev,
+ port->bulk_in_endpointAddress),
+ urb->transfer_buffer, urb->transfer_buffer_length,
+ safe_read_bulk_callback, port);
+
+ result = usb_submit_urb(urb, GFP_ATOMIC);
+ if (result)
+ err("%s - failed resubmitting read urb, error %d",
+ __func__, result);
/* FIXME: Need a mechanism to retry later if this happens */
- }
}
static int safe_write(struct tty_struct *tty, struct usb_serial_port *port,
int i;
int packet_length;
- dbg ("safe_write port: %p %d urb: %p count: %d", port, port->number, port->write_urb,
- count);
+ dbg("safe_write port: %p %d urb: %p count: %d",
+ port, port->number, port->write_urb, count);
if (!port->write_urb) {
- dbg ("%s - write urb NULL", __func__);
+ dbg("%s - write urb NULL", __func__);
return 0;
}
- dbg ("safe_write write_urb: %d transfer_buffer_length",
+ dbg("safe_write write_urb: %d transfer_buffer_length",
port->write_urb->transfer_buffer_length);
if (!port->write_urb->transfer_buffer_length) {
- dbg ("%s - write urb transfer_buffer_length zero", __func__);
+ dbg("%s - write urb transfer_buffer_length zero", __func__);
return 0;
}
if (count == 0) {
- dbg ("%s - write request of 0 bytes", __func__);
+ dbg("%s - write request of 0 bytes", __func__);
return 0;
}
spin_lock_bh(&port->lock);
port->write_urb_busy = 1;
spin_unlock_bh(&port->lock);
- packet_length = port->bulk_out_size; // get max packetsize
+ packet_length = port->bulk_out_size; /* get max packetsize */
- i = packet_length - (safe ? 2 : 0); // get bytes to send
+ i = packet_length - (safe ? 2 : 0); /* get bytes to send */
count = (count > i) ? i : count;
- // get the data into the transfer buffer
+ /* get the data into the transfer buffer */
data = port->write_urb->transfer_buffer;
- memset (data, '0', packet_length);
+ memset(data, '0', packet_length);
- memcpy (data, buf, count);
+ memcpy(data, buf, count);
if (safe) {
__u16 fcs;
- // pad if necessary
- if (!padded) {
+ /* pad if necessary */
+ if (!padded)
packet_length = count + 2;
- }
- // set count
+ /* set count */
data[packet_length - 2] = count << 2;
data[packet_length - 1] = 0;
- // compute fcs and insert into trailer
- fcs = fcs_compute10 (data, packet_length, CRC10_INITFCS);
+ /* compute fcs and insert into trailer */
+ fcs = fcs_compute10(data, packet_length, CRC10_INITFCS);
data[packet_length - 2] |= fcs >> 8;
data[packet_length - 1] |= fcs & 0xff;
- // set length to send
+ /* set length to send */
port->write_urb->transfer_buffer_length = packet_length;
} else {
port->write_urb->transfer_buffer_length = count;
}
- usb_serial_debug_data(debug, &port->dev, __func__, count, port->write_urb->transfer_buffer);
+ usb_serial_debug_data(debug, &port->dev, __func__, count,
+ port->write_urb->transfer_buffer);
#ifdef ECHO_TX
{
int i;
unsigned char *cp = port->write_urb->transfer_buffer;
for (i = 0; i < port->write_urb->transfer_buffer_length; i++) {
- if ((i % 32) == 0) {
- printk ("\nsu[%02x] ", i);
- }
- printk ("%02x ", *cp++);
+ if ((i % 32) == 0)
+ printk("\nsu[%02x] ", i);
+ printk("%02x ", *cp++);
}
- printk ("\n");
+ printk("\n");
}
#endif
port->write_urb->dev = port->serial->dev;
- if ((result = usb_submit_urb (port->write_urb, GFP_KERNEL))) {
+ result = usb_submit_urb(port->write_urb, GFP_KERNEL);
+ if (result) {
port->write_urb_busy = 0;
- err ("%s - failed submitting write urb, error %d", __func__, result);
+ err("%s - failed submitting write urb, error %d",
+ __func__, result);
return 0;
}
- dbg ("%s urb: %p submitted", __func__, port->write_urb);
+ dbg("%s urb: %p submitted", __func__, port->write_urb);
- return (count);
+ return count;
}
static int safe_write_room(struct tty_struct *tty)
int room = 0; /* Default: no room */
unsigned long flags;
- dbg ("%s", __func__);
+ dbg("%s", __func__);
spin_lock_irqsave(&port->lock, flags);
if (port->write_urb_busy)
room = port->bulk_out_size - (safe ? 2 : 0);
spin_unlock_irqrestore(&port->lock, flags);
- if (room) {
- dbg ("safe_write_room returns %d", room);
- }
-
+ if (room)
+ dbg("safe_write_room returns %d", room);
return room;
}
-static int safe_startup (struct usb_serial *serial)
+static int safe_startup(struct usb_serial *serial)
{
switch (serial->interface->cur_altsetting->desc.bInterfaceProtocol) {
case LINEO_SAFESERIAL_CRC:
.attach = safe_startup,
};
-static int __init safe_init (void)
+static int __init safe_init(void)
{
int i, retval;
- info (DRIVER_VERSION " " DRIVER_AUTHOR);
- info (DRIVER_DESC);
- info ("vendor: %x product: %x safe: %d padded: %d\n", vendor, product, safe, padded);
+ info(DRIVER_VERSION " " DRIVER_AUTHOR);
+ info(DRIVER_DESC);
+ info("vendor: %x product: %x safe: %d padded: %d\n",
+ vendor, product, safe, padded);
- // if we have vendor / product parameters patch them into id list
+ /* if we have vendor / product parameters patch them into id list */
if (vendor || product) {
- info ("vendor: %x product: %x\n", vendor, product);
+ info("vendor: %x product: %x\n", vendor, product);
for (i = 0; i < ARRAY_SIZE(id_table); i++) {
if (!id_table[i].idVendor && !id_table[i].idProduct) {
return retval;
}
-static void __exit safe_exit (void)
+static void __exit safe_exit(void)
{
- usb_deregister (&safe_driver);
- usb_serial_deregister (&safe_device);
+ usb_deregister(&safe_driver);
+ usb_serial_deregister(&safe_device);
}
-module_init (safe_init);
-module_exit (safe_exit);
+module_init(safe_init);
+module_exit(safe_exit);
projects / linux-2.6-omap-h63xx.git / commitdiff