1. add common GPIO handling code into [arch/arm/plat-pxa]
2. common code in <mach/gpio.h> moved into <plat/gpio.h>, new processors
should implement its own <mach/gpio.h>, provide the following required
definitions and '#include <plat/gpio.h>' in the end:
- GPIO_REGS_VIRT for mapped virtual address of the GPIO registers'
physical I/O memory
- macros of GPLR(), GPSR(), GPDR() for constant optimization for
functions gpio_{set,get}_value() (so that bit-bang code can still
have tolerable performance)
- NR_BUILTIN_GPIO for the number of onchip GPIO
- definitions of __gpio_is_inverted() and __gpio_is_occupied(), they
can be either macros or inlined functions
Signed-off-by: Eric Miao <eric.miao@marvell.com>
# Common support (must be linked before board specific support)
obj-y += clock.o devices.o generic.o irq.o \
- time.o gpio.o reset.o
+ time.o reset.o
obj-$(CONFIG_PM) += pm.o sleep.o standby.o
ifeq ($(CONFIG_CPU_FREQ),y)
#define GAFR(x) GPIO_REG(0x54 + (((x) & 0x70) >> 2))
-/* NOTE: some PXAs have fewer on-chip GPIOs (like PXA255, with 85).
- * Those cases currently cause holes in the GPIO number space, the
- * actual number of the last GPIO is recorded by 'pxa_last_gpio'.
- */
-extern int pxa_last_gpio;
-
#define NR_BUILTIN_GPIO 128
-static inline int gpio_get_value(unsigned gpio)
-{
- if (__builtin_constant_p(gpio) && (gpio < NR_BUILTIN_GPIO))
- return GPLR(gpio) & GPIO_bit(gpio);
- else
- return __gpio_get_value(gpio);
-}
-
-static inline void gpio_set_value(unsigned gpio, int value)
-{
- if (__builtin_constant_p(gpio) && (gpio < NR_BUILTIN_GPIO)) {
- if (value)
- GPSR(gpio) = GPIO_bit(gpio);
- else
- GPCR(gpio) = GPIO_bit(gpio);
- } else {
- __gpio_set_value(gpio, value);
- }
-}
-
-#define gpio_cansleep __gpio_cansleep
#define gpio_to_bank(gpio) ((gpio) >> 5)
#define gpio_to_irq(gpio) IRQ_GPIO(gpio)
#define irq_to_gpio(irq) IRQ_TO_GPIO(irq)
-
#ifdef CONFIG_CPU_PXA26x
/* GPIO86/87/88/89 on PXA26x have their direction bits in GPDR2 inverted,
* as well as their Alternate Function value being '1' for GPIO in GAFRx.
return GPDR(gpio) & GPIO_bit(gpio);
}
-typedef int (*set_wake_t)(unsigned int irq, unsigned int on);
-
-extern void pxa_init_gpio(int mux_irq, int start, int end, set_wake_t fn);
+#include <plat/gpio.h>
#endif
obj-y := dma.o
+obj-$(CONFIG_GENERIC_GPIO) += gpio.o
/*
- * linux/arch/arm/mach-pxa/gpio.c
+ * linux/arch/arm/plat-pxa/gpio.c
*
* Generic PXA GPIO handling
*
int pxa_last_gpio;
-/*
- * We handle the GPIOs by banks, each bank covers up to 32 GPIOs with
- * one set of registers. The register offsets are organized below:
- *
- * GPLR GPDR GPSR GPCR GRER GFER GEDR
- * BANK 0 - 0x0000 0x000C 0x0018 0x0024 0x0030 0x003C 0x0048
- * BANK 1 - 0x0004 0x0010 0x001C 0x0028 0x0034 0x0040 0x004C
- * BANK 2 - 0x0008 0x0014 0x0020 0x002C 0x0038 0x0044 0x0050
- *
- * BANK 3 - 0x0100 0x010C 0x0118 0x0124 0x0130 0x013C 0x0148
- * BANK 4 - 0x0104 0x0110 0x011C 0x0128 0x0134 0x0140 0x014C
- * BANK 5 - 0x0108 0x0114 0x0120 0x012C 0x0138 0x0144 0x0150
- *
- * NOTE:
- * BANK 3 is only available on PXA27x and later processors.
- * BANK 4 and 5 are only available on PXA935
- */
-
-#define GPIO_BANK(n) (GPIO_REGS_VIRT + BANK_OFF(n))
-
-#define GPLR_OFFSET 0x00
-#define GPDR_OFFSET 0x0C
-#define GPSR_OFFSET 0x18
-#define GPCR_OFFSET 0x24
-#define GRER_OFFSET 0x30
-#define GFER_OFFSET 0x3C
-#define GEDR_OFFSET 0x48
-
struct pxa_gpio_chip {
struct gpio_chip chip;
void __iomem *regbase;
--- /dev/null
+#ifndef __PLAT_GPIO_H
+#define __PLAT_GPIO_H
+
+/*
+ * We handle the GPIOs by banks, each bank covers up to 32 GPIOs with
+ * one set of registers. The register offsets are organized below:
+ *
+ * GPLR GPDR GPSR GPCR GRER GFER GEDR
+ * BANK 0 - 0x0000 0x000C 0x0018 0x0024 0x0030 0x003C 0x0048
+ * BANK 1 - 0x0004 0x0010 0x001C 0x0028 0x0034 0x0040 0x004C
+ * BANK 2 - 0x0008 0x0014 0x0020 0x002C 0x0038 0x0044 0x0050
+ *
+ * BANK 3 - 0x0100 0x010C 0x0118 0x0124 0x0130 0x013C 0x0148
+ * BANK 4 - 0x0104 0x0110 0x011C 0x0128 0x0134 0x0140 0x014C
+ * BANK 5 - 0x0108 0x0114 0x0120 0x012C 0x0138 0x0144 0x0150
+ *
+ * NOTE:
+ * BANK 3 is only available on PXA27x and later processors.
+ * BANK 4 and 5 are only available on PXA935
+ */
+
+#define GPIO_BANK(n) (GPIO_REGS_VIRT + BANK_OFF(n))
+
+#define GPLR_OFFSET 0x00
+#define GPDR_OFFSET 0x0C
+#define GPSR_OFFSET 0x18
+#define GPCR_OFFSET 0x24
+#define GRER_OFFSET 0x30
+#define GFER_OFFSET 0x3C
+#define GEDR_OFFSET 0x48
+
+static inline int gpio_get_value(unsigned gpio)
+{
+ if (__builtin_constant_p(gpio) && (gpio < NR_BUILTIN_GPIO))
+ return GPLR(gpio) & GPIO_bit(gpio);
+ else
+ return __gpio_get_value(gpio);
+}
+
+static inline void gpio_set_value(unsigned gpio, int value)
+{
+ if (__builtin_constant_p(gpio) && (gpio < NR_BUILTIN_GPIO)) {
+ if (value)
+ GPSR(gpio) = GPIO_bit(gpio);
+ else
+ GPCR(gpio) = GPIO_bit(gpio);
+ } else
+ __gpio_set_value(gpio, value);
+}
+
+#define gpio_cansleep __gpio_cansleep
+
+/* NOTE: some PXAs have fewer on-chip GPIOs (like PXA255, with 85).
+ * Those cases currently cause holes in the GPIO number space, the
+ * actual number of the last GPIO is recorded by 'pxa_last_gpio'.
+ */
+extern int pxa_last_gpio;
+
+typedef int (*set_wake_t)(unsigned int irq, unsigned int on);
+
+extern void pxa_init_gpio(int mux_irq, int start, int end, set_wake_t fn);
+#endif /* __PLAT_GPIO_H */
projects / linux-2.6-omap-h63xx.git / commitdiff