/**
* sdc_init_panel() - initialize a synchronous LCD panel.
- * @mx3fb: mx3fb context.
- * @panel: panel type.
- * @pixel_clk: desired pixel clock frequency in Hz.
- * @width: width of panel in pixels.
- * @height: height of panel in pixels.
- * @pixel_fmt: pixel format of buffer as FOURCC ASCII code.
- * @h_start_width: number of pixel clocks between the HSYNC signal pulse
- * and the start of valid data.
- * @h_sync_width: width of the HSYNC signal in units of pixel clocks.
- * @h_end_width: number of pixel clocks between the end of valid data
- * and the HSYNC signal for next line.
- * @v_start_width: number of lines between the VSYNC signal pulse and the
- * start of valid data.
- * @v_sync_width: width of the VSYNC signal in units of lines
- * @v_end_width: number of lines between the end of valid data and the
- * VSYNC signal for next frame.
- * @sig: bitfield of signal polarities for LCD interface.
- * @return: 0 on success or negative error code on failure.
+ * @mx3fb: mx3fb context.
+ * @panel: panel type.
+ * @pixel_clk: desired pixel clock frequency in Hz.
+ * @width: width of panel in pixels.
+ * @height: height of panel in pixels.
+ * @pixel_fmt: pixel format of buffer as FOURCC ASCII code.
+ * @h_start_width: number of pixel clocks between the HSYNC signal pulse
+ * and the start of valid data.
+ * @h_sync_width: width of the HSYNC signal in units of pixel clocks.
+ * @h_end_width: number of pixel clocks between the end of valid data
+ * and the HSYNC signal for next line.
+ * @v_start_width: number of lines between the VSYNC signal pulse and the
+ * start of valid data.
+ * @v_sync_width: width of the VSYNC signal in units of lines
+ * @v_end_width: number of lines between the end of valid data and the
+ * VSYNC signal for next frame.
+ * @sig: bitfield of signal polarities for LCD interface.
+ * @return: 0 on success or negative error code on failure.
*/
static int sdc_init_panel(struct mx3fb_data *mx3fb, enum ipu_panel panel,
- uint32_t pixel_clk,
- uint16_t width, uint16_t height,
- enum pixel_fmt pixel_fmt,
- uint16_t h_start_width, uint16_t h_sync_width,
- uint16_t h_end_width, uint16_t v_start_width,
- uint16_t v_sync_width, uint16_t v_end_width,
- struct ipu_di_signal_cfg sig)
+ uint32_t pixel_clk,
+ uint16_t width, uint16_t height,
+ enum pixel_fmt pixel_fmt,
+ uint16_t h_start_width, uint16_t h_sync_width,
+ uint16_t h_end_width, uint16_t v_start_width,
+ uint16_t v_sync_width, uint16_t v_end_width,
+ struct ipu_di_signal_cfg sig)
{
- unsigned long lock_flags;
- uint32_t reg;
- uint32_t old_conf;
- uint32_t div;
- struct clk *ipu_clk;
+ unsigned long lock_flags;
+ uint32_t reg;
+ uint32_t old_conf;
+ uint32_t div;
+ struct clk *ipu_clk;
- dev_dbg(mx3fb->dev, "panel size = %d x %d", width, height);
+ dev_dbg(mx3fb->dev, "panel size = %d x %d", width, height);
- if (v_sync_width == 0 || h_sync_width == 0)
- return -EINVAL;
+ if (v_sync_width == 0 || h_sync_width == 0)
+ return -EINVAL;
- /* Init panel size and blanking periods */
- reg = ((uint32_t) (h_sync_width - 1) << 26) |
- ((uint32_t) (width + h_start_width + h_end_width - 1) << 16);
- mx3fb_write_reg(mx3fb, reg, SDC_HOR_CONF);
+ /* Init panel size and blanking periods */
+ reg = ((uint32_t) (h_sync_width - 1) << 26) |
+ ((uint32_t) (width + h_start_width + h_end_width - 1) << 16);
+ mx3fb_write_reg(mx3fb, reg, SDC_HOR_CONF);
#ifdef DEBUG
- printk(KERN_CONT " hor_conf %x,", reg);
+ printk(KERN_CONT " hor_conf %x,", reg);
#endif
- reg = ((uint32_t) (v_sync_width - 1) << 26) | SDC_V_SYNC_WIDTH_L |
- ((uint32_t) (height + v_start_width + v_end_width - 1) << 16);
- mx3fb_write_reg(mx3fb, reg, SDC_VER_CONF);
+ reg = ((uint32_t) (v_sync_width - 1) << 26) | SDC_V_SYNC_WIDTH_L |
+ ((uint32_t) (height + v_start_width + v_end_width - 1) << 16);
+ mx3fb_write_reg(mx3fb, reg, SDC_VER_CONF);
#ifdef DEBUG
- printk(KERN_CONT " ver_conf %x\n", reg);
+ printk(KERN_CONT " ver_conf %x\n", reg);
#endif
- mx3fb->h_start_width = h_start_width;
- mx3fb->v_start_width = v_start_width;
-
- switch (panel) {
- case IPU_PANEL_SHARP_TFT:
- mx3fb_write_reg(mx3fb, 0x00FD0102L, SDC_SHARP_CONF_1);
- mx3fb_write_reg(mx3fb, 0x00F500F4L, SDC_SHARP_CONF_2);
- mx3fb_write_reg(mx3fb, SDC_COM_SHARP | SDC_COM_TFT_COLOR, SDC_COM_CONF);
- break;
- case IPU_PANEL_TFT:
- mx3fb_write_reg(mx3fb, SDC_COM_TFT_COLOR, SDC_COM_CONF);
- break;
- default:
- return -EINVAL;
- }
-
- /* Init clocking */
-
- /*
- * Calculate divider: fractional part is 4 bits so simply multiple by
- * 24 to get fractional part, as long as we stay under ~250MHz and on
- * i.MX31 it (HSP_CLK) is <= 178MHz. Currently 128.267MHz
- */
- dev_dbg(mx3fb->dev, "pixel clk = %d\n", pixel_clk);
-
- ipu_clk = clk_get(mx3fb->dev, NULL);
- div = clk_get_rate(ipu_clk) * 16 / pixel_clk;
- clk_put(ipu_clk);
-
- if (div < 0x40) { /* Divider less than 4 */
- dev_dbg(mx3fb->dev,
- "InitPanel() - Pixel clock divider less than 4\n");
- div = 0x40;
- }
-
- spin_lock_irqsave(&mx3fb->lock, lock_flags);
-
- /*
- * DISP3_IF_CLK_DOWN_WR is half the divider value and 2 fraction bits
- * fewer. Subtract 1 extra from DISP3_IF_CLK_DOWN_WR based on timing
- * debug. DISP3_IF_CLK_UP_WR is 0
- */
- mx3fb_write_reg(mx3fb, (((div / 8) - 1) << 22) | div, DI_DISP3_TIME_CONF);
-
- /* DI settings */
- old_conf = mx3fb_read_reg(mx3fb, DI_DISP_IF_CONF) & 0x78FFFFFF;
- old_conf |= sig.datamask_en << DI_D3_DATAMSK_SHIFT |
- sig.clksel_en << DI_D3_CLK_SEL_SHIFT |
- sig.clkidle_en << DI_D3_CLK_IDLE_SHIFT;
- mx3fb_write_reg(mx3fb, old_conf, DI_DISP_IF_CONF);
-
- old_conf = mx3fb_read_reg(mx3fb, DI_DISP_SIG_POL) & 0xE0FFFFFF;
- old_conf |= sig.data_pol << DI_D3_DATA_POL_SHIFT |
- sig.clk_pol << DI_D3_CLK_POL_SHIFT |
- sig.enable_pol << DI_D3_DRDY_SHARP_POL_SHIFT |
- sig.Hsync_pol << DI_D3_HSYNC_POL_SHIFT |
- sig.Vsync_pol << DI_D3_VSYNC_POL_SHIFT;
- mx3fb_write_reg(mx3fb, old_conf, DI_DISP_SIG_POL);
-
- switch (pixel_fmt) {
- case IPU_PIX_FMT_RGB24:
- mx3fb_write_reg(mx3fb, di_mappings[0], DI_DISP3_B0_MAP);
- mx3fb_write_reg(mx3fb, di_mappings[1], DI_DISP3_B1_MAP);
- mx3fb_write_reg(mx3fb, di_mappings[2], DI_DISP3_B2_MAP);
- mx3fb_write_reg(mx3fb, mx3fb_read_reg(mx3fb, DI_DISP_ACC_CC) |
- ((di_mappings[3] - 1) << 12), DI_DISP_ACC_CC);
- break;
- case IPU_PIX_FMT_RGB666:
- mx3fb_write_reg(mx3fb, di_mappings[4], DI_DISP3_B0_MAP);
- mx3fb_write_reg(mx3fb, di_mappings[5], DI_DISP3_B1_MAP);
- mx3fb_write_reg(mx3fb, di_mappings[6], DI_DISP3_B2_MAP);
- mx3fb_write_reg(mx3fb, mx3fb_read_reg(mx3fb, DI_DISP_ACC_CC) |
- ((di_mappings[7] - 1) << 12), DI_DISP_ACC_CC);
- break;
- case IPU_PIX_FMT_BGR666:
- mx3fb_write_reg(mx3fb, di_mappings[8], DI_DISP3_B0_MAP);
- mx3fb_write_reg(mx3fb, di_mappings[9], DI_DISP3_B1_MAP);
- mx3fb_write_reg(mx3fb, di_mappings[10], DI_DISP3_B2_MAP);
- mx3fb_write_reg(mx3fb, mx3fb_read_reg(mx3fb, DI_DISP_ACC_CC) |
- ((di_mappings[11] - 1) << 12), DI_DISP_ACC_CC);
- break;
- default:
- mx3fb_write_reg(mx3fb, di_mappings[12], DI_DISP3_B0_MAP);
- mx3fb_write_reg(mx3fb, di_mappings[13], DI_DISP3_B1_MAP);
- mx3fb_write_reg(mx3fb, di_mappings[14], DI_DISP3_B2_MAP);
- mx3fb_write_reg(mx3fb, mx3fb_read_reg(mx3fb, DI_DISP_ACC_CC) |
- ((di_mappings[15] - 1) << 12), DI_DISP_ACC_CC);
- break;
- }
-
- spin_unlock_irqrestore(&mx3fb->lock, lock_flags);
-
- dev_dbg(mx3fb->dev, "DI_DISP_IF_CONF = 0x%08X\n",
- mx3fb_read_reg(mx3fb, DI_DISP_IF_CONF));
- dev_dbg(mx3fb->dev, "DI_DISP_SIG_POL = 0x%08X\n",
- mx3fb_read_reg(mx3fb, DI_DISP_SIG_POL));
- dev_dbg(mx3fb->dev, "DI_DISP3_TIME_CONF = 0x%08X\n",
- mx3fb_read_reg(mx3fb, DI_DISP3_TIME_CONF));
-
- return 0;
+ mx3fb->h_start_width = h_start_width;
+ mx3fb->v_start_width = v_start_width;
+
+ switch (panel) {
+ case IPU_PANEL_SHARP_TFT:
+ mx3fb_write_reg(mx3fb, 0x00FD0102L, SDC_SHARP_CONF_1);
+ mx3fb_write_reg(mx3fb, 0x00F500F4L, SDC_SHARP_CONF_2);
+ mx3fb_write_reg(mx3fb, SDC_COM_SHARP | SDC_COM_TFT_COLOR, SDC_COM_CONF);
+ break;
+ case IPU_PANEL_TFT:
+ mx3fb_write_reg(mx3fb, SDC_COM_TFT_COLOR, SDC_COM_CONF);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ /* Init clocking */
+
+ /*
+ * Calculate divider: fractional part is 4 bits so simply multiple by
+ * 2^4 to get fractional part, as long as we stay under ~250MHz and on
+ * i.MX31 it (HSP_CLK) is <= 178MHz. Currently 128.267MHz
+ */
+ dev_dbg(mx3fb->dev, "pixel clk = %d\n", pixel_clk);
+
- ipu_clk = clk_get(mx3fb->dev, "ipu_clk");
++ ipu_clk = clk_get(mx3fb->dev, NULL);
+ div = clk_get_rate(ipu_clk) * 16 / pixel_clk;
+ clk_put(ipu_clk);
+
+ if (div < 0x40) { /* Divider less than 4 */
+ dev_dbg(mx3fb->dev,
+ "InitPanel() - Pixel clock divider less than 4\n");
+ div = 0x40;
+ }
+
+ spin_lock_irqsave(&mx3fb->lock, lock_flags);
+
+ /*
+ * DISP3_IF_CLK_DOWN_WR is half the divider value and 2 fraction bits
+ * fewer. Subtract 1 extra from DISP3_IF_CLK_DOWN_WR based on timing
+ * debug. DISP3_IF_CLK_UP_WR is 0
+ */
+ mx3fb_write_reg(mx3fb, (((div / 8) - 1) << 22) | div, DI_DISP3_TIME_CONF);
+
+ /* DI settings */
+ old_conf = mx3fb_read_reg(mx3fb, DI_DISP_IF_CONF) & 0x78FFFFFF;
+ old_conf |= sig.datamask_en << DI_D3_DATAMSK_SHIFT |
+ sig.clksel_en << DI_D3_CLK_SEL_SHIFT |
+ sig.clkidle_en << DI_D3_CLK_IDLE_SHIFT;
+ mx3fb_write_reg(mx3fb, old_conf, DI_DISP_IF_CONF);
+
+ old_conf = mx3fb_read_reg(mx3fb, DI_DISP_SIG_POL) & 0xE0FFFFFF;
+ old_conf |= sig.data_pol << DI_D3_DATA_POL_SHIFT |
+ sig.clk_pol << DI_D3_CLK_POL_SHIFT |
+ sig.enable_pol << DI_D3_DRDY_SHARP_POL_SHIFT |
+ sig.Hsync_pol << DI_D3_HSYNC_POL_SHIFT |
+ sig.Vsync_pol << DI_D3_VSYNC_POL_SHIFT;
+ mx3fb_write_reg(mx3fb, old_conf, DI_DISP_SIG_POL);
+
+ switch (pixel_fmt) {
+ case IPU_PIX_FMT_RGB24:
+ mx3fb_write_reg(mx3fb, di_mappings[0], DI_DISP3_B0_MAP);
+ mx3fb_write_reg(mx3fb, di_mappings[1], DI_DISP3_B1_MAP);
+ mx3fb_write_reg(mx3fb, di_mappings[2], DI_DISP3_B2_MAP);
+ mx3fb_write_reg(mx3fb, mx3fb_read_reg(mx3fb, DI_DISP_ACC_CC) |
+ ((di_mappings[3] - 1) << 12), DI_DISP_ACC_CC);
+ break;
+ case IPU_PIX_FMT_RGB666:
+ mx3fb_write_reg(mx3fb, di_mappings[4], DI_DISP3_B0_MAP);
+ mx3fb_write_reg(mx3fb, di_mappings[5], DI_DISP3_B1_MAP);
+ mx3fb_write_reg(mx3fb, di_mappings[6], DI_DISP3_B2_MAP);
+ mx3fb_write_reg(mx3fb, mx3fb_read_reg(mx3fb, DI_DISP_ACC_CC) |
+ ((di_mappings[7] - 1) << 12), DI_DISP_ACC_CC);
+ break;
+ case IPU_PIX_FMT_BGR666:
+ mx3fb_write_reg(mx3fb, di_mappings[8], DI_DISP3_B0_MAP);
+ mx3fb_write_reg(mx3fb, di_mappings[9], DI_DISP3_B1_MAP);
+ mx3fb_write_reg(mx3fb, di_mappings[10], DI_DISP3_B2_MAP);
+ mx3fb_write_reg(mx3fb, mx3fb_read_reg(mx3fb, DI_DISP_ACC_CC) |
+ ((di_mappings[11] - 1) << 12), DI_DISP_ACC_CC);
+ break;
+ default:
+ mx3fb_write_reg(mx3fb, di_mappings[12], DI_DISP3_B0_MAP);
+ mx3fb_write_reg(mx3fb, di_mappings[13], DI_DISP3_B1_MAP);
+ mx3fb_write_reg(mx3fb, di_mappings[14], DI_DISP3_B2_MAP);
+ mx3fb_write_reg(mx3fb, mx3fb_read_reg(mx3fb, DI_DISP_ACC_CC) |
+ ((di_mappings[15] - 1) << 12), DI_DISP_ACC_CC);
+ break;
+ }
+
+ spin_unlock_irqrestore(&mx3fb->lock, lock_flags);
+
+ dev_dbg(mx3fb->dev, "DI_DISP_IF_CONF = 0x%08X\n",
+ mx3fb_read_reg(mx3fb, DI_DISP_IF_CONF));
+ dev_dbg(mx3fb->dev, "DI_DISP_SIG_POL = 0x%08X\n",
+ mx3fb_read_reg(mx3fb, DI_DISP_SIG_POL));
+ dev_dbg(mx3fb->dev, "DI_DISP3_TIME_CONF = 0x%08X\n",
+ mx3fb_read_reg(mx3fb, DI_DISP3_TIME_CONF));
+
+ return 0;
}
/**
projects / linux-2.6-omap-h63xx.git / commitdiff