[PATCH] skge: cleanup ethtool mode support

Unify mapping of supported modes based on hardware.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>

diff --git a/drivers/net/skge.c b/drivers/net/skge.c
index 68de7f748a81581d0b81da752e18593f25d82c8d..81b8fe9581c7144c08fb6c41f2903e858cd048a8 100644 (file)
--- a/drivers/net/skge.c
+++ b/drivers/net/skge.c
@@ -179,6 +179,36 @@ static int skge_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
        return 0;
 }
 
+/* Determine supported/adverised modes based on hardware.
+ * Note: ethtoool ADVERTISED_xxx == SUPPORTED_xxx
+ */
+static u32 skge_supported_modes(const struct skge_hw *hw)
+{
+       u32 supported;
+
+       if (iscopper(hw)) {
+               supported = SUPPORTED_10baseT_Half
+                       | SUPPORTED_10baseT_Full
+                       | SUPPORTED_100baseT_Half
+                       | SUPPORTED_100baseT_Full
+                       | SUPPORTED_1000baseT_Half
+                       | SUPPORTED_1000baseT_Full
+                       | SUPPORTED_Autoneg| SUPPORTED_TP;
+
+               if (hw->chip_id == CHIP_ID_GENESIS)
+                       supported &= ~(SUPPORTED_10baseT_Half
+                                            | SUPPORTED_10baseT_Full
+                                            | SUPPORTED_100baseT_Half
+                                            | SUPPORTED_100baseT_Full);
+
+               else if (hw->chip_id == CHIP_ID_YUKON)
+                       supported &= ~SUPPORTED_1000baseT_Half;
+       } else
+               supported = SUPPORTED_1000baseT_Full | SUPPORTED_FIBRE
+                       | SUPPORTED_Autoneg;
+
+       return supported;
+}
 
 static int skge_get_settings(struct net_device *dev,
                             struct ethtool_cmd *ecmd)
@@ -187,35 +217,13 @@ static int skge_get_settings(struct net_device *dev,
        struct skge_hw *hw = skge->hw;
 
        ecmd->transceiver = XCVR_INTERNAL;
+       ecmd->supported = skge_supported_modes(hw);
 
        if (iscopper(hw)) {
-               if (hw->chip_id == CHIP_ID_GENESIS)
-                       ecmd->supported = SUPPORTED_1000baseT_Full
-                               | SUPPORTED_1000baseT_Half
-                               | SUPPORTED_Autoneg | SUPPORTED_TP;
-               else {
-                       ecmd->supported = SUPPORTED_10baseT_Half
-                               | SUPPORTED_10baseT_Full
-                               | SUPPORTED_100baseT_Half
-                               | SUPPORTED_100baseT_Full
-                               | SUPPORTED_1000baseT_Half
-                               | SUPPORTED_1000baseT_Full
-                               | SUPPORTED_Autoneg| SUPPORTED_TP;
-
-                       if (hw->chip_id == CHIP_ID_YUKON)
-                               ecmd->supported &= ~SUPPORTED_1000baseT_Half;
-
-               }
-
                ecmd->port = PORT_TP;
                ecmd->phy_address = hw->phy_addr;
-       } else {
-               ecmd->supported = SUPPORTED_1000baseT_Full
-                       | SUPPORTED_FIBRE
-                       | SUPPORTED_Autoneg;
-
+       } else
                ecmd->port = PORT_FIBRE;
-       }
 
        ecmd->advertising = skge->advertising;
        ecmd->autoneg = skge->autoneg;
@@ -224,60 +232,57 @@ static int skge_get_settings(struct net_device *dev,
        return 0;
 }
 
-static u32 skge_modes(const struct skge_hw *hw)
-{
-       u32 modes = ADVERTISED_Autoneg
-               | ADVERTISED_1000baseT_Full | ADVERTISED_1000baseT_Half
-               | ADVERTISED_100baseT_Full | ADVERTISED_100baseT_Half
-               | ADVERTISED_10baseT_Full | ADVERTISED_10baseT_Half;
-
-       if (iscopper(hw)) {
-               modes |= ADVERTISED_TP;
-               switch (hw->chip_id) {
-               case CHIP_ID_GENESIS:
-                       modes &= ~(ADVERTISED_100baseT_Full
-                                  | ADVERTISED_100baseT_Half
-                                  | ADVERTISED_10baseT_Full
-                                  | ADVERTISED_10baseT_Half);
-                       break;
-
-               case CHIP_ID_YUKON:
-                       modes &= ~ADVERTISED_1000baseT_Half;
-                       break;
-
-               }
-       } else {
-               modes |= ADVERTISED_FIBRE;
-               modes &= ~ADVERTISED_1000baseT_Half;
-       }
-       return modes;
-}
-
 static int skge_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
 {
        struct skge_port *skge = netdev_priv(dev);
        const struct skge_hw *hw = skge->hw;
+       u32 supported = skge_supported_modes(hw);
 
        if (ecmd->autoneg == AUTONEG_ENABLE) {
-               if (ecmd->advertising & skge_modes(hw))
-                       return -EINVAL;
+               ecmd->advertising = supported;
+               skge->duplex = -1;
+               skge->speed = -1;
        } else {
-               switch (ecmd->speed) {
+               u32 setting;
+
+               switch(ecmd->speed) {
                case SPEED_1000:
+                       if (ecmd->duplex == DUPLEX_FULL)
+                               setting = SUPPORTED_1000baseT_Full;
+                       else if (ecmd->duplex == DUPLEX_HALF)
+                               setting = SUPPORTED_1000baseT_Half;
+                       else
+                               return -EINVAL;
                        break;
                case SPEED_100:
+                       if (ecmd->duplex == DUPLEX_FULL)
+                               setting = SUPPORTED_100baseT_Full;
+                       else if (ecmd->duplex == DUPLEX_HALF)
+                               setting = SUPPORTED_100baseT_Half;
+                       else
+                               return -EINVAL;
+                       break;
+
                case SPEED_10:
-                       if (iscopper(hw) || hw->chip_id == CHIP_ID_GENESIS)
+                       if (ecmd->duplex == DUPLEX_FULL)
+                               setting = SUPPORTED_10baseT_Full;
+                       else if (ecmd->duplex == DUPLEX_HALF)
+                               setting = SUPPORTED_10baseT_Half;
+                       else
                                return -EINVAL;
                        break;
                default:
                        return -EINVAL;
                }
+
+               if ((setting & supported) == 0)
+                       return -EINVAL;
+
+               skge->speed = ecmd->speed;
+               skge->duplex = ecmd->duplex;
        }
 
        skge->autoneg = ecmd->autoneg;
-       skge->speed = ecmd->speed;
-       skge->duplex = ecmd->duplex;
        skge->advertising = ecmd->advertising;
 
        if (netif_running(dev)) {
@@ -2973,7 +2978,7 @@ static struct net_device *skge_devinit(struct skge_hw *hw, int port,
        skge->flow_control = FLOW_MODE_SYMMETRIC;
        skge->duplex = -1;
        skge->speed = -1;
-       skge->advertising = skge_modes(hw);
+       skge->advertising = skge_supported_modes(hw);
 
        hw->dev[port] = dev;