bool "OMAP730 Based System"
select ARCH_OMAP_OTG
-config ARCH_OMAP1510
+config ARCH_OMAP15XX
depends on ARCH_OMAP1
default y
- bool "OMAP1510 Based System"
+ bool "OMAP15xx Based System"
config ARCH_OMAP16XX
depends on ARCH_OMAP1
config MACH_OMAP_INNOVATOR
bool "TI Innovator"
- depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX)
+ depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX)
help
TI OMAP 1510 or 1610 Innovator board support. Say Y here if you
have such a board.
config MACH_VOICEBLUE
bool "Voiceblue"
- depends on ARCH_OMAP1 && ARCH_OMAP1510
+ depends on ARCH_OMAP1 && ARCH_OMAP15XX
help
Support for Voiceblue GSM/VoIP gateway. Say Y here if you have
such a board.
config MACH_NETSTAR
bool "NetStar"
- depends on ARCH_OMAP1 && ARCH_OMAP1510
+ depends on ARCH_OMAP1 && ARCH_OMAP15XX
help
Support for NetStar PBX. Say Y here if you have such a board.
+config MACH_OMAP_PALMTE
+ bool "Palm Tungsten E"
+ depends on ARCH_OMAP1 && ARCH_OMAP15XX
+ help
+ Support for the Palm Tungsten E PDA. Currently only the LCD panel
+ is supported. To boot the kernel, you'll need a PalmOS compatible
+ bootloader; check out http://palmtelinux.sourceforge.net for more
+ informations.
+ Say Y here if you have such a PDA, say NO otherwise.
+
config MACH_OMAP_GENERIC
bool "Generic OMAP board"
- depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX)
+ depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX)
help
Support for generic OMAP-1510, 1610 or 1710 board with
no FPGA. Can be used as template for porting Linux to
config OMAP_ARM_168MHZ
bool "OMAP ARM 168 MHz CPU"
- depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX || ARCH_OMAP730)
+ depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730)
help
Enable 168MHz clock for OMAP CPU. If unsure, say N.
config OMAP_ARM_150MHZ
bool "OMAP ARM 150 MHz CPU"
- depends on ARCH_OMAP1 && ARCH_OMAP1510
+ depends on ARCH_OMAP1 && ARCH_OMAP15XX
help
Enable 150MHz clock for OMAP CPU. If unsure, say N.
config OMAP_ARM_120MHZ
bool "OMAP ARM 120 MHz CPU"
- depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX || ARCH_OMAP730)
+ depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730)
help
Enable 120MHz clock for OMAP CPU. If unsure, say N.
config OMAP_ARM_60MHZ
bool "OMAP ARM 60 MHz CPU"
- depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX || ARCH_OMAP730)
+ depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730)
default y
help
Enable 60MHz clock for OMAP CPU. If unsure, say Y.
config OMAP_ARM_30MHZ
bool "OMAP ARM 30 MHz CPU"
- depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX || ARCH_OMAP730)
+ depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730)
help
Enable 30MHz clock for OMAP CPU. If unsure, say N.
#
# Common support
-obj-y := io.o id.o irq.o time.o serial.o devices.o
+obj-y := io.o id.o clock.o irq.o time.o mux.o serial.o devices.o
led-y := leds.o
# Specific board support
obj-$(CONFIG_MACH_OMAP_H3) += board-h3.o
obj-$(CONFIG_MACH_VOICEBLUE) += board-voiceblue.o
obj-$(CONFIG_MACH_NETSTAR) += board-netstar.o
+obj-$(CONFIG_MACH_OMAP_PALMTE) += board-palmte.o
-ifeq ($(CONFIG_ARCH_OMAP1510),y)
+ifeq ($(CONFIG_ARCH_OMAP15XX),y)
# Innovator-1510 FPGA
obj-$(CONFIG_MACH_OMAP_INNOVATOR) += fpga.o
endif
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/device.h>
+#include <linux/platform_device.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/arch/board.h>
#include <asm/arch/common.h>
-static int __initdata generic_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1};
-
static void __init omap_generic_init_irq(void)
{
omap_init_irq();
/* assume no Mini-AB port */
-#ifdef CONFIG_ARCH_OMAP1510
+#ifdef CONFIG_ARCH_OMAP15XX
static struct omap_usb_config generic1510_usb_config __initdata = {
.register_host = 1,
.register_dev = 1,
#endif
+static struct omap_uart_config generic_uart_config __initdata = {
+ .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
+};
+
static struct omap_board_config_kernel generic_config[] = {
{ OMAP_TAG_USB, NULL },
{ OMAP_TAG_MMC, &generic_mmc_config },
+ { OMAP_TAG_UART, &generic_uart_config },
};
static void __init omap_generic_init(void)
{
- const struct omap_uart_config *uart_conf;
-
- /*
- * Make sure the serial ports are muxed on at this point.
- * You have to mux them off in device drivers later on
- * if not needed.
- */
-#ifdef CONFIG_ARCH_OMAP1510
+#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
generic_config[0].data = &generic1510_usb_config;
}
}
#endif
- uart_conf = omap_get_config(OMAP_TAG_UART, struct omap_uart_config);
- if (uart_conf != NULL) {
- unsigned int enabled_ports, i;
-
- enabled_ports = uart_conf->enabled_uarts;
- for (i = 0; i < 3; i++) {
- if (!(enabled_ports & (1 << i)))
- generic_serial_ports[i] = 0;
- }
- }
-
omap_board_config = generic_config;
omap_board_config_size = ARRAY_SIZE(generic_config);
- omap_serial_init(generic_serial_ports);
+ omap_serial_init();
}
static void __init omap_generic_map_io(void)
extern int omap_gpio_init(void);
-static int __initdata h2_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1};
-
static struct mtd_partition h2_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
},
};
+static struct omap_uart_config h2_uart_config __initdata = {
+ .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
+};
+
+static struct omap_lcd_config h2_lcd_config __initdata = {
+ .panel_name = "h2",
+ .ctrl_name = "internal",
+};
+
static struct omap_board_config_kernel h2_config[] = {
{ OMAP_TAG_USB, &h2_usb_config },
{ OMAP_TAG_MMC, &h2_mmc_config },
+ { OMAP_TAG_UART, &h2_uart_config },
+ { OMAP_TAG_LCD, &h2_lcd_config },
};
static void __init h2_init(void)
platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices));
omap_board_config = h2_config;
omap_board_config_size = ARRAY_SIZE(h2_config);
+ omap_serial_init();
}
static void __init h2_map_io(void)
{
omap_map_common_io();
- omap_serial_init(h2_serial_ports);
}
MACHINE_START(OMAP_H2, "TI-H2")
extern int omap_gpio_init(void);
-static int __initdata h3_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1};
-
static struct mtd_partition h3_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
},
};
+static struct omap_uart_config h3_uart_config __initdata = {
+ .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
+};
+
+static struct omap_lcd_config h3_lcd_config __initdata = {
+ .panel_name = "h3",
+ .ctrl_name = "internal",
+};
+
static struct omap_board_config_kernel h3_config[] = {
- { OMAP_TAG_USB, &h3_usb_config },
- { OMAP_TAG_MMC, &h3_mmc_config },
+ { OMAP_TAG_USB, &h3_usb_config },
+ { OMAP_TAG_MMC, &h3_mmc_config },
+ { OMAP_TAG_UART, &h3_uart_config },
+ { OMAP_TAG_LCD, &h3_lcd_config },
};
static void __init h3_init(void)
(void) platform_add_devices(devices, ARRAY_SIZE(devices));
omap_board_config = h3_config;
omap_board_config_size = ARRAY_SIZE(h3_config);
+ omap_serial_init();
}
static void __init h3_init_smc91x(void)
static void __init h3_map_io(void)
{
omap_map_common_io();
- omap_serial_init(h3_serial_ports);
}
MACHINE_START(OMAP_H3, "TI OMAP1710 H3 board")
#include <asm/arch/usb.h>
#include <asm/arch/common.h>
-static int __initdata innovator_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1};
-
static struct mtd_partition innovator_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
.resource = &innovator_flash_resource,
};
-#ifdef CONFIG_ARCH_OMAP1510
+#ifdef CONFIG_ARCH_OMAP15XX
/* Only FPGA needs to be mapped here. All others are done with ioremap */
static struct map_desc innovator1510_io_desc[] __initdata = {
&innovator1510_smc91x_device,
};
-#endif /* CONFIG_ARCH_OMAP1510 */
+#endif /* CONFIG_ARCH_OMAP15XX */
#ifdef CONFIG_ARCH_OMAP16XX
{
omap_init_irq();
omap_gpio_init();
-#ifdef CONFIG_ARCH_OMAP1510
+#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
omap1510_fpga_init_irq();
}
innovator_init_smc91x();
}
-#ifdef CONFIG_ARCH_OMAP1510
+#ifdef CONFIG_ARCH_OMAP15XX
static struct omap_usb_config innovator1510_usb_config __initdata = {
/* for bundled non-standard host and peripheral cables */
.hmc_mode = 4,
.register_dev = 1,
.pins[0] = 2,
};
+
+static struct omap_lcd_config innovator1510_lcd_config __initdata = {
+ .panel_name = "inn1510",
+ .ctrl_name = "internal",
+};
#endif
#ifdef CONFIG_ARCH_OMAP16XX
.pins[1] = 3,
};
+
+static struct omap_lcd_config innovator1610_lcd_config __initdata = {
+ .panel_name = "inn1610",
+ .ctrl_name = "internal",
+};
#endif
static struct omap_mmc_config innovator_mmc_config __initdata = {
},
};
+static struct omap_uart_config innovator_uart_config __initdata = {
+ .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
+};
+
static struct omap_board_config_kernel innovator_config[] = {
{ OMAP_TAG_USB, NULL },
+ { OMAP_TAG_LCD, NULL },
{ OMAP_TAG_MMC, &innovator_mmc_config },
+ { OMAP_TAG_UART, &innovator_uart_config },
};
static void __init innovator_init(void)
{
-#ifdef CONFIG_ARCH_OMAP1510
+#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
platform_add_devices(innovator1510_devices, ARRAY_SIZE(innovator1510_devices));
}
}
#endif
-#ifdef CONFIG_ARCH_OMAP1510
- if (cpu_is_omap1510())
+#ifdef CONFIG_ARCH_OMAP15XX
+ if (cpu_is_omap1510()) {
innovator_config[0].data = &innovator1510_usb_config;
+ innovator_config[1].data = &innovator1510_lcd_config;
+ }
#endif
#ifdef CONFIG_ARCH_OMAP16XX
- if (cpu_is_omap1610())
+ if (cpu_is_omap1610()) {
innovator_config[0].data = &h2_usb_config;
+ innovator_config[1].data = &innovator1610_lcd_config;
+ }
#endif
omap_board_config = innovator_config;
omap_board_config_size = ARRAY_SIZE(innovator_config);
+ omap_serial_init();
}
static void __init innovator_map_io(void)
{
omap_map_common_io();
-#ifdef CONFIG_ARCH_OMAP1510
+#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
iotable_init(innovator1510_io_desc, ARRAY_SIZE(innovator1510_io_desc));
udelay(10); /* Delay needed for FPGA */
fpga_read(OMAP1510_FPGA_BOARD_REV));
}
#endif
- omap_serial_init(innovator_serial_ports);
}
MACHINE_START(OMAP_INNOVATOR, "TI-Innovator")
&netstar_smc91x_device,
};
+static struct omap_uart_config netstar_uart_config __initdata = {
+ .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
+};
+
+static struct omap_board_config_kernel netstar_config[] = {
+ { OMAP_TAG_UART, &netstar_uart_config },
+};
+
static void __init netstar_init_irq(void)
{
omap_init_irq();
/* Switch off red LED */
omap_writeb(0x00, OMAP_LPG1_PMR); /* Disable clock */
omap_writeb(0x80, OMAP_LPG1_LCR);
-}
-static int __initdata omap_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1};
+ omap_board_config = netstar_config;
+ omap_board_config_size = ARRAY_SIZE(netstar_config);
+ omap_serial_init();
+}
static void __init netstar_map_io(void)
{
omap_map_common_io();
- omap_serial_init(omap_serial_ports);
}
#define MACHINE_PANICED 1
#include <asm/arch/tc.h>
#include <asm/arch/common.h>
-static int __initdata osk_serial_ports[OMAP_MAX_NR_PORTS] = {1, 0, 0};
-
static struct mtd_partition osk_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
}
/* Check EMIFS wait states to fix errors with SMC_GET_PKT_HDR */
- EMIFS_CCS(1) |= 0x2;
+ EMIFS_CCS(1) |= 0x3;
}
static void __init osk_init_cf(void)
.pins[0] = 2,
};
+static struct omap_uart_config osk_uart_config __initdata = {
+ .enabled_uarts = (1 << 0),
+};
+
+static struct omap_lcd_config osk_lcd_config __initdata = {
+ .panel_name = "osk",
+ .ctrl_name = "internal",
+};
+
static struct omap_board_config_kernel osk_config[] = {
{ OMAP_TAG_USB, &osk_usb_config },
+ { OMAP_TAG_UART, &osk_uart_config },
+ { OMAP_TAG_LCD, &osk_lcd_config },
};
#ifdef CONFIG_OMAP_OSK_MISTRAL
omap_board_config_size = ARRAY_SIZE(osk_config);
USB_TRANSCEIVER_CTRL_REG |= (3 << 1);
+ omap_serial_init();
osk_mistral_init();
}
static void __init osk_map_io(void)
{
omap_map_common_io();
- omap_serial_init(osk_serial_ports);
}
MACHINE_START(OMAP_OSK, "TI-OSK")
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap1/board-palmte.c
+ *
+ * Modified from board-generic.c
+ *
+ * Support for the Palm Tungsten E PDA.
+ *
+ * Original version : Laurent Gonzalez
+ *
+ * Maintainters : http://palmtelinux.sf.net
+ * palmtelinux-developpers@lists.sf.net
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/notifier.h>
+
+#include <asm/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <asm/arch/gpio.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/usb.h>
+#include <asm/arch/board.h>
+#include <asm/arch/common.h>
+#include <asm/hardware/clock.h>
+
+static void __init omap_generic_init_irq(void)
+{
+ omap_init_irq();
+}
+
+static struct omap_usb_config palmte_usb_config __initdata = {
+ .register_dev = 1,
+ .hmc_mode = 0,
+ .pins[0] = 3,
+};
+
+static struct omap_mmc_config palmte_mmc_config __initdata = {
+ .mmc [0] = {
+ .enabled = 1,
+ .wire4 = 1,
+ .wp_pin = OMAP_MPUIO(3),
+ .power_pin = -1,
+ .switch_pin = -1,
+ },
+};
+
+static struct omap_lcd_config palmte_lcd_config __initdata = {
+ .panel_name = "palmte",
+ .ctrl_name = "internal",
+};
+
+static struct omap_board_config_kernel palmte_config[] = {
+ { OMAP_TAG_USB, &palmte_usb_config },
+ { OMAP_TAG_MMC, &palmte_mmc_config },
+ { OMAP_TAG_LCD, &palmte_lcd_config },
+};
+
+static void __init omap_generic_init(void)
+{
+ omap_board_config = palmte_config;
+ omap_board_config_size = ARRAY_SIZE(palmte_config);
+}
+
+static void __init omap_generic_map_io(void)
+{
+ omap_map_common_io();
+}
+
+MACHINE_START(OMAP_PALMTE, "OMAP310 based Palm Tungsten E")
+ .phys_ram = 0x10000000,
+ .phys_io = 0xfff00000,
+ .io_pg_offst = ((0xfef00000) >> 18) & 0xfffc,
+ .boot_params = 0x10000100,
+ .map_io = omap_generic_map_io,
+ .init_irq = omap_generic_init_irq,
+ .init_machine = omap_generic_init,
+ .timer = &omap_timer,
+MACHINE_END
#include <asm/arch/mux.h>
#include <asm/arch/fpga.h>
#include <asm/arch/common.h>
+#include <asm/arch/board.h>
static struct resource smc91x_resources[] = {
[0] = {
},
};
-static int __initdata p2_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 0};
-
static struct mtd_partition p2_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
&smc91x_device,
};
+static struct omap_uart_config perseus2_uart_config __initdata = {
+ .enabled_uarts = ((1 << 0) | (1 << 1)),
+};
+
+static struct omap_lcd_config perseus2_lcd_config __initdata = {
+ .panel_name = "p2",
+ .ctrl_name = "internal",
+};
+
+static struct omap_board_config_kernel perseus2_config[] = {
+ { OMAP_TAG_UART, &perseus2_uart_config },
+ { OMAP_TAG_LCD, &perseus2_lcd_config },
+};
+
static void __init omap_perseus2_init(void)
{
(void) platform_add_devices(devices, ARRAY_SIZE(devices));
+
+ omap_board_config = perseus2_config;
+ omap_board_config_size = ARRAY_SIZE(perseus2_config);
+ omap_serial_init();
}
static void __init perseus2_init_smc91x(void)
omap_gpio_init();
perseus2_init_smc91x();
}
-
/* Only FPGA needs to be mapped here. All others are done with ioremap */
static struct map_desc omap_perseus2_io_desc[] __initdata = {
{
* It is used as the Ethernet controller interrupt
*/
omap_writel(omap_readl(OMAP730_IO_CONF_9) & 0x1FFFFFFF, OMAP730_IO_CONF_9);
- omap_serial_init(p2_serial_ports);
}
MACHINE_START(OMAP_PERSEUS2, "OMAP730 Perseus2")
},
};
+static struct omap_uart_config voiceblue_uart_config __initdata = {
+ .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
+};
+
static struct omap_board_config_kernel voiceblue_config[] = {
{ OMAP_TAG_USB, &voiceblue_usb_config },
{ OMAP_TAG_MMC, &voiceblue_mmc_config },
+ { OMAP_TAG_UART, &voiceblue_uart_config },
};
static void __init voiceblue_init_irq(void)
platform_add_devices(voiceblue_devices, ARRAY_SIZE(voiceblue_devices));
omap_board_config = voiceblue_config;
omap_board_config_size = ARRAY_SIZE(voiceblue_config);
+ omap_serial_init();
/* There is a good chance board is going up, so enable power LED
* (it is connected through invertor) */
omap_writeb(0x00, OMAP_LPG1_PMR); /* Disable clock */
}
-static int __initdata omap_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1};
-
static void __init voiceblue_map_io(void)
{
omap_map_common_io();
- omap_serial_init(omap_serial_ports);
}
#define MACHINE_PANICED 1
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap1/clock.c
+ *
+ * Copyright (C) 2004 - 2005 Nokia corporation
+ * Written by Tuukka Tikkanen <tuukka.tikkanen@elektrobit.com>
+ *
+ * Modified to use omap shared clock framework by
+ * Tony Lindgren <tony@atomide.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+
+#include <asm/io.h>
+#include <asm/hardware/clock.h>
+
+#include <asm/arch/usb.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sram.h>
+
+#include "clock.h"
+
+__u32 arm_idlect1_mask;
+
+/*-------------------------------------------------------------------------
+ * Omap1 specific clock functions
+ *-------------------------------------------------------------------------*/
+
+static void omap1_watchdog_recalc(struct clk * clk)
+{
+ clk->rate = clk->parent->rate / 14;
+}
+
+static void omap1_uart_recalc(struct clk * clk)
+{
+ unsigned int val = omap_readl(clk->enable_reg);
+ if (val & clk->enable_bit)
+ clk->rate = 48000000;
+ else
+ clk->rate = 12000000;
+}
+
+static int omap1_clk_enable_dsp_domain(struct clk *clk)
+{
+ int retval;
+
+ retval = omap1_clk_use(&api_ck.clk);
+ if (!retval) {
+ retval = omap1_clk_enable(clk);
+ omap1_clk_unuse(&api_ck.clk);
+ }
+
+ return retval;
+}
+
+static void omap1_clk_disable_dsp_domain(struct clk *clk)
+{
+ if (omap1_clk_use(&api_ck.clk) == 0) {
+ omap1_clk_disable(clk);
+ omap1_clk_unuse(&api_ck.clk);
+ }
+}
+
+static int omap1_clk_enable_uart_functional(struct clk *clk)
+{
+ int ret;
+ struct uart_clk *uclk;
+
+ ret = omap1_clk_enable(clk);
+ if (ret == 0) {
+ /* Set smart idle acknowledgement mode */
+ uclk = (struct uart_clk *)clk;
+ omap_writeb((omap_readb(uclk->sysc_addr) & ~0x10) | 8,
+ uclk->sysc_addr);
+ }
+
+ return ret;
+}
+
+static void omap1_clk_disable_uart_functional(struct clk *clk)
+{
+ struct uart_clk *uclk;
+
+ /* Set force idle acknowledgement mode */
+ uclk = (struct uart_clk *)clk;
+ omap_writeb((omap_readb(uclk->sysc_addr) & ~0x18), uclk->sysc_addr);
+
+ omap1_clk_disable(clk);
+}
+
+static void omap1_clk_allow_idle(struct clk *clk)
+{
+ struct arm_idlect1_clk * iclk = (struct arm_idlect1_clk *)clk;
+
+ if (!(clk->flags & CLOCK_IDLE_CONTROL))
+ return;
+
+ if (iclk->no_idle_count > 0 && !(--iclk->no_idle_count))
+ arm_idlect1_mask |= 1 << iclk->idlect_shift;
+}
+
+static void omap1_clk_deny_idle(struct clk *clk)
+{
+ struct arm_idlect1_clk * iclk = (struct arm_idlect1_clk *)clk;
+
+ if (!(clk->flags & CLOCK_IDLE_CONTROL))
+ return;
+
+ if (iclk->no_idle_count++ == 0)
+ arm_idlect1_mask &= ~(1 << iclk->idlect_shift);
+}
+
+static __u16 verify_ckctl_value(__u16 newval)
+{
+ /* This function checks for following limitations set
+ * by the hardware (all conditions must be true):
+ * DSPMMU_CK == DSP_CK or DSPMMU_CK == DSP_CK/2
+ * ARM_CK >= TC_CK
+ * DSP_CK >= TC_CK
+ * DSPMMU_CK >= TC_CK
+ *
+ * In addition following rules are enforced:
+ * LCD_CK <= TC_CK
+ * ARMPER_CK <= TC_CK
+ *
+ * However, maximum frequencies are not checked for!
+ */
+ __u8 per_exp;
+ __u8 lcd_exp;
+ __u8 arm_exp;
+ __u8 dsp_exp;
+ __u8 tc_exp;
+ __u8 dspmmu_exp;
+
+ per_exp = (newval >> CKCTL_PERDIV_OFFSET) & 3;
+ lcd_exp = (newval >> CKCTL_LCDDIV_OFFSET) & 3;
+ arm_exp = (newval >> CKCTL_ARMDIV_OFFSET) & 3;
+ dsp_exp = (newval >> CKCTL_DSPDIV_OFFSET) & 3;
+ tc_exp = (newval >> CKCTL_TCDIV_OFFSET) & 3;
+ dspmmu_exp = (newval >> CKCTL_DSPMMUDIV_OFFSET) & 3;
+
+ if (dspmmu_exp < dsp_exp)
+ dspmmu_exp = dsp_exp;
+ if (dspmmu_exp > dsp_exp+1)
+ dspmmu_exp = dsp_exp+1;
+ if (tc_exp < arm_exp)
+ tc_exp = arm_exp;
+ if (tc_exp < dspmmu_exp)
+ tc_exp = dspmmu_exp;
+ if (tc_exp > lcd_exp)
+ lcd_exp = tc_exp;
+ if (tc_exp > per_exp)
+ per_exp = tc_exp;
+
+ newval &= 0xf000;
+ newval |= per_exp << CKCTL_PERDIV_OFFSET;
+ newval |= lcd_exp << CKCTL_LCDDIV_OFFSET;
+ newval |= arm_exp << CKCTL_ARMDIV_OFFSET;
+ newval |= dsp_exp << CKCTL_DSPDIV_OFFSET;
+ newval |= tc_exp << CKCTL_TCDIV_OFFSET;
+ newval |= dspmmu_exp << CKCTL_DSPMMUDIV_OFFSET;
+
+ return newval;
+}
+
+static int calc_dsor_exp(struct clk *clk, unsigned long rate)
+{
+ /* Note: If target frequency is too low, this function will return 4,
+ * which is invalid value. Caller must check for this value and act
+ * accordingly.
+ *
+ * Note: This function does not check for following limitations set
+ * by the hardware (all conditions must be true):
+ * DSPMMU_CK == DSP_CK or DSPMMU_CK == DSP_CK/2
+ * ARM_CK >= TC_CK
+ * DSP_CK >= TC_CK
+ * DSPMMU_CK >= TC_CK
+ */
+ unsigned long realrate;
+ struct clk * parent;
+ unsigned dsor_exp;
+
+ if (unlikely(!(clk->flags & RATE_CKCTL)))
+ return -EINVAL;
+
+ parent = clk->parent;
+ if (unlikely(parent == 0))
+ return -EIO;
+
+ realrate = parent->rate;
+ for (dsor_exp=0; dsor_exp<4; dsor_exp++) {
+ if (realrate <= rate)
+ break;
+
+ realrate /= 2;
+ }
+
+ return dsor_exp;
+}
+
+static void omap1_ckctl_recalc(struct clk * clk)
+{
+ int dsor;
+
+ /* Calculate divisor encoded as 2-bit exponent */
+ dsor = 1 << (3 & (omap_readw(ARM_CKCTL) >> clk->rate_offset));
+
+ if (unlikely(clk->rate == clk->parent->rate / dsor))
+ return; /* No change, quick exit */
+ clk->rate = clk->parent->rate / dsor;
+
+ if (unlikely(clk->flags & RATE_PROPAGATES))
+ propagate_rate(clk);
+}
+
+static void omap1_ckctl_recalc_dsp_domain(struct clk * clk)
+{
+ int dsor;
+
+ /* Calculate divisor encoded as 2-bit exponent
+ *
+ * The clock control bits are in DSP domain,
+ * so api_ck is needed for access.
+ * Note that DSP_CKCTL virt addr = phys addr, so
+ * we must use __raw_readw() instead of omap_readw().
+ */
+ omap1_clk_use(&api_ck.clk);
+ dsor = 1 << (3 & (__raw_readw(DSP_CKCTL) >> clk->rate_offset));
+ omap1_clk_unuse(&api_ck.clk);
+
+ if (unlikely(clk->rate == clk->parent->rate / dsor))
+ return; /* No change, quick exit */
+ clk->rate = clk->parent->rate / dsor;
+
+ if (unlikely(clk->flags & RATE_PROPAGATES))
+ propagate_rate(clk);
+}
+
+/* MPU virtual clock functions */
+static int omap1_select_table_rate(struct clk * clk, unsigned long rate)
+{
+ /* Find the highest supported frequency <= rate and switch to it */
+ struct mpu_rate * ptr;
+
+ if (clk != &virtual_ck_mpu)
+ return -EINVAL;
+
+ for (ptr = rate_table; ptr->rate; ptr++) {
+ if (ptr->xtal != ck_ref.rate)
+ continue;
+
+ /* DPLL1 cannot be reprogrammed without risking system crash */
+ if (likely(ck_dpll1.rate!=0) && ptr->pll_rate != ck_dpll1.rate)
+ continue;
+
+ /* Can check only after xtal frequency check */
+ if (ptr->rate <= rate)
+ break;
+ }
+
+ if (!ptr->rate)
+ return -EINVAL;
+
+ /*
+ * In most cases we should not need to reprogram DPLL.
+ * Reprogramming the DPLL is tricky, it must be done from SRAM.
+ */
+ omap_sram_reprogram_clock(ptr->dpllctl_val, ptr->ckctl_val);
+
+ ck_dpll1.rate = ptr->pll_rate;
+ propagate_rate(&ck_dpll1);
+ return 0;
+}
+
+static int omap1_clk_set_rate_dsp_domain(struct clk *clk, unsigned long rate)
+{
+ int ret = -EINVAL;
+ int dsor_exp;
+ __u16 regval;
+
+ if (clk->flags & RATE_CKCTL) {
+ dsor_exp = calc_dsor_exp(clk, rate);
+ if (dsor_exp > 3)
+ dsor_exp = -EINVAL;
+ if (dsor_exp < 0)
+ return dsor_exp;
+
+ regval = __raw_readw(DSP_CKCTL);
+ regval &= ~(3 << clk->rate_offset);
+ regval |= dsor_exp << clk->rate_offset;
+ __raw_writew(regval, DSP_CKCTL);
+ clk->rate = clk->parent->rate / (1 << dsor_exp);
+ ret = 0;
+ }
+
+ if (unlikely(ret == 0 && (clk->flags & RATE_PROPAGATES)))
+ propagate_rate(clk);
+
+ return ret;
+}
+
+static long omap1_round_to_table_rate(struct clk * clk, unsigned long rate)
+{
+ /* Find the highest supported frequency <= rate */
+ struct mpu_rate * ptr;
+ long highest_rate;
+
+ if (clk != &virtual_ck_mpu)
+ return -EINVAL;
+
+ highest_rate = -EINVAL;
+
+ for (ptr = rate_table; ptr->rate; ptr++) {
+ if (ptr->xtal != ck_ref.rate)
+ continue;
+
+ highest_rate = ptr->rate;
+
+ /* Can check only after xtal frequency check */
+ if (ptr->rate <= rate)
+ break;
+ }
+
+ return highest_rate;
+}
+
+static unsigned calc_ext_dsor(unsigned long rate)
+{
+ unsigned dsor;
+
+ /* MCLK and BCLK divisor selection is not linear:
+ * freq = 96MHz / dsor
+ *
+ * RATIO_SEL range: dsor <-> RATIO_SEL
+ * 0..6: (RATIO_SEL+2) <-> (dsor-2)
+ * 6..48: (8+(RATIO_SEL-6)*2) <-> ((dsor-8)/2+6)
+ * Minimum dsor is 2 and maximum is 96. Odd divisors starting from 9
+ * can not be used.
+ */
+ for (dsor = 2; dsor < 96; ++dsor) {
+ if ((dsor & 1) && dsor > 8)
+ continue;
+ if (rate >= 96000000 / dsor)
+ break;
+ }
+ return dsor;
+}
+
+/* Only needed on 1510 */
+static int omap1_set_uart_rate(struct clk * clk, unsigned long rate)
+{
+ unsigned int val;
+
+ val = omap_readl(clk->enable_reg);
+ if (rate == 12000000)
+ val &= ~(1 << clk->enable_bit);
+ else if (rate == 48000000)
+ val |= (1 << clk->enable_bit);
+ else
+ return -EINVAL;
+ omap_writel(val, clk->enable_reg);
+ clk->rate = rate;
+
+ return 0;
+}
+
+/* External clock (MCLK & BCLK) functions */
+static int omap1_set_ext_clk_rate(struct clk * clk, unsigned long rate)
+{
+ unsigned dsor;
+ __u16 ratio_bits;
+
+ dsor = calc_ext_dsor(rate);
+ clk->rate = 96000000 / dsor;
+ if (dsor > 8)
+ ratio_bits = ((dsor - 8) / 2 + 6) << 2;
+ else
+ ratio_bits = (dsor - 2) << 2;
+
+ ratio_bits |= omap_readw(clk->enable_reg) & ~0xfd;
+ omap_writew(ratio_bits, clk->enable_reg);
+
+ return 0;
+}
+
+static long omap1_round_ext_clk_rate(struct clk * clk, unsigned long rate)
+{
+ return 96000000 / calc_ext_dsor(rate);
+}
+
+static void omap1_init_ext_clk(struct clk * clk)
+{
+ unsigned dsor;
+ __u16 ratio_bits;
+
+ /* Determine current rate and ensure clock is based on 96MHz APLL */
+ ratio_bits = omap_readw(clk->enable_reg) & ~1;
+ omap_writew(ratio_bits, clk->enable_reg);
+
+ ratio_bits = (ratio_bits & 0xfc) >> 2;
+ if (ratio_bits > 6)
+ dsor = (ratio_bits - 6) * 2 + 8;
+ else
+ dsor = ratio_bits + 2;
+
+ clk-> rate = 96000000 / dsor;
+}
+
+static int omap1_clk_use(struct clk *clk)
+{
+ int ret = 0;
+ if (clk->usecount++ == 0) {
+ if (likely(clk->parent)) {
+ ret = omap1_clk_use(clk->parent);
+
+ if (unlikely(ret != 0)) {
+ clk->usecount--;
+ return ret;
+ }
+
+ if (clk->flags & CLOCK_NO_IDLE_PARENT)
+ if (!cpu_is_omap24xx())
+ omap1_clk_deny_idle(clk->parent);
+ }
+
+ ret = clk->enable(clk);
+
+ if (unlikely(ret != 0) && clk->parent) {
+ omap1_clk_unuse(clk->parent);
+ clk->usecount--;
+ }
+ }
+
+ return ret;
+}
+
+static void omap1_clk_unuse(struct clk *clk)
+{
+ if (clk->usecount > 0 && !(--clk->usecount)) {
+ clk->disable(clk);
+ if (likely(clk->parent)) {
+ omap1_clk_unuse(clk->parent);
+ if (clk->flags & CLOCK_NO_IDLE_PARENT)
+ if (!cpu_is_omap24xx())
+ omap1_clk_allow_idle(clk->parent);
+ }
+ }
+}
+
+static int omap1_clk_enable(struct clk *clk)
+{
+ __u16 regval16;
+ __u32 regval32;
+
+ if (clk->flags & ALWAYS_ENABLED)
+ return 0;
+
+ if (unlikely(clk->enable_reg == 0)) {
+ printk(KERN_ERR "clock.c: Enable for %s without enable code\n",
+ clk->name);
+ return 0;
+ }
+
+ if (clk->flags & ENABLE_REG_32BIT) {
+ if (clk->flags & VIRTUAL_IO_ADDRESS) {
+ regval32 = __raw_readl(clk->enable_reg);
+ regval32 |= (1 << clk->enable_bit);
+ __raw_writel(regval32, clk->enable_reg);
+ } else {
+ regval32 = omap_readl(clk->enable_reg);
+ regval32 |= (1 << clk->enable_bit);
+ omap_writel(regval32, clk->enable_reg);
+ }
+ } else {
+ if (clk->flags & VIRTUAL_IO_ADDRESS) {
+ regval16 = __raw_readw(clk->enable_reg);
+ regval16 |= (1 << clk->enable_bit);
+ __raw_writew(regval16, clk->enable_reg);
+ } else {
+ regval16 = omap_readw(clk->enable_reg);
+ regval16 |= (1 << clk->enable_bit);
+ omap_writew(regval16, clk->enable_reg);
+ }
+ }
+
+ return 0;
+}
+
+static void omap1_clk_disable(struct clk *clk)
+{
+ __u16 regval16;
+ __u32 regval32;
+
+ if (clk->enable_reg == 0)
+ return;
+
+ if (clk->flags & ENABLE_REG_32BIT) {
+ if (clk->flags & VIRTUAL_IO_ADDRESS) {
+ regval32 = __raw_readl(clk->enable_reg);
+ regval32 &= ~(1 << clk->enable_bit);
+ __raw_writel(regval32, clk->enable_reg);
+ } else {
+ regval32 = omap_readl(clk->enable_reg);
+ regval32 &= ~(1 << clk->enable_bit);
+ omap_writel(regval32, clk->enable_reg);
+ }
+ } else {
+ if (clk->flags & VIRTUAL_IO_ADDRESS) {
+ regval16 = __raw_readw(clk->enable_reg);
+ regval16 &= ~(1 << clk->enable_bit);
+ __raw_writew(regval16, clk->enable_reg);
+ } else {
+ regval16 = omap_readw(clk->enable_reg);
+ regval16 &= ~(1 << clk->enable_bit);
+ omap_writew(regval16, clk->enable_reg);
+ }
+ }
+}
+
+static long omap1_clk_round_rate(struct clk *clk, unsigned long rate)
+{
+ int dsor_exp;
+
+ if (clk->flags & RATE_FIXED)
+ return clk->rate;
+
+ if (clk->flags & RATE_CKCTL) {
+ dsor_exp = calc_dsor_exp(clk, rate);
+ if (dsor_exp < 0)
+ return dsor_exp;
+ if (dsor_exp > 3)
+ dsor_exp = 3;
+ return clk->parent->rate / (1 << dsor_exp);
+ }
+
+ if(clk->round_rate != 0)
+ return clk->round_rate(clk, rate);
+
+ return clk->rate;
+}
+
+static int omap1_clk_set_rate(struct clk *clk, unsigned long rate)
+{
+ int ret = -EINVAL;
+ int dsor_exp;
+ __u16 regval;
+
+ if (clk->set_rate)
+ ret = clk->set_rate(clk, rate);
+ else if (clk->flags & RATE_CKCTL) {
+ dsor_exp = calc_dsor_exp(clk, rate);
+ if (dsor_exp > 3)
+ dsor_exp = -EINVAL;
+ if (dsor_exp < 0)
+ return dsor_exp;
+
+ regval = omap_readw(ARM_CKCTL);
+ regval &= ~(3 << clk->rate_offset);
+ regval |= dsor_exp << clk->rate_offset;
+ regval = verify_ckctl_value(regval);
+ omap_writew(regval, ARM_CKCTL);
+ clk->rate = clk->parent->rate / (1 << dsor_exp);
+ ret = 0;
+ }
+
+ if (unlikely(ret == 0 && (clk->flags & RATE_PROPAGATES)))
+ propagate_rate(clk);
+
+ return ret;
+}
+
+/*-------------------------------------------------------------------------
+ * Omap1 clock reset and init functions
+ *-------------------------------------------------------------------------*/
+
+#ifdef CONFIG_OMAP_RESET_CLOCKS
+/*
+ * Resets some clocks that may be left on from bootloader,
+ * but leaves serial clocks on. See also omap_late_clk_reset().
+ */
+static inline void omap1_early_clk_reset(void)
+{
+ //omap_writel(0x3 << 29, MOD_CONF_CTRL_0);
+}
+
+static int __init omap1_late_clk_reset(void)
+{
+ /* Turn off all unused clocks */
+ struct clk *p;
+ __u32 regval32;
+
+ /* USB_REQ_EN will be disabled later if necessary (usb_dc_ck) */
+ regval32 = omap_readw(SOFT_REQ_REG) & (1 << 4);
+ omap_writew(regval32, SOFT_REQ_REG);
+ omap_writew(0, SOFT_REQ_REG2);
+
+ list_for_each_entry(p, &clocks, node) {
+ if (p->usecount > 0 || (p->flags & ALWAYS_ENABLED) ||
+ p->enable_reg == 0)
+ continue;
+
+ /* Clocks in the DSP domain need api_ck. Just assume bootloader
+ * has not enabled any DSP clocks */
+ if ((u32)p->enable_reg == DSP_IDLECT2) {
+ printk(KERN_INFO "Skipping reset check for DSP domain "
+ "clock \"%s\"\n", p->name);
+ continue;
+ }
+
+ /* Is the clock already disabled? */
+ if (p->flags & ENABLE_REG_32BIT) {
+ if (p->flags & VIRTUAL_IO_ADDRESS)
+ regval32 = __raw_readl(p->enable_reg);
+ else
+ regval32 = omap_readl(p->enable_reg);
+ } else {
+ if (p->flags & VIRTUAL_IO_ADDRESS)
+ regval32 = __raw_readw(p->enable_reg);
+ else
+ regval32 = omap_readw(p->enable_reg);
+ }
+
+ if ((regval32 & (1 << p->enable_bit)) == 0)
+ continue;
+
+ /* FIXME: This clock seems to be necessary but no-one
+ * has asked for its activation. */
+ if (p == &tc2_ck // FIX: pm.c (SRAM), CCP, Camera
+ || p == &ck_dpll1out.clk // FIX: SoSSI, SSR
+ || p == &arm_gpio_ck // FIX: GPIO code for 1510
+ ) {
+ printk(KERN_INFO "FIXME: Clock \"%s\" seems unused\n",
+ p->name);
+ continue;
+ }
+
+ printk(KERN_INFO "Disabling unused clock \"%s\"... ", p->name);
+ p->disable(p);
+ printk(" done\n");
+ }
+
+ return 0;
+}
+late_initcall(omap1_late_clk_reset);
+
+#else
+#define omap1_early_clk_reset() {}
+#endif
+
+static struct clk_functions omap1_clk_functions = {
+ .clk_use = omap1_clk_use,
+ .clk_unuse = omap1_clk_unuse,
+ .clk_round_rate = omap1_clk_round_rate,
+ .clk_set_rate = omap1_clk_set_rate,
+};
+
+int __init omap1_clk_init(void)
+{
+ struct clk ** clkp;
+ const struct omap_clock_config *info;
+ int crystal_type = 0; /* Default 12 MHz */
+
+ omap1_early_clk_reset();
+ clk_init(&omap1_clk_functions);
+
+ /* By default all idlect1 clocks are allowed to idle */
+ arm_idlect1_mask = ~0;
+
+ for (clkp = onchip_clks; clkp < onchip_clks+ARRAY_SIZE(onchip_clks); clkp++) {
+ if (((*clkp)->flags &CLOCK_IN_OMAP1510) && cpu_is_omap1510()) {
+ clk_register(*clkp);
+ continue;
+ }
+
+ if (((*clkp)->flags &CLOCK_IN_OMAP16XX) && cpu_is_omap16xx()) {
+ clk_register(*clkp);
+ continue;
+ }
+
+ if (((*clkp)->flags &CLOCK_IN_OMAP730) && cpu_is_omap730()) {
+ clk_register(*clkp);
+ continue;
+ }
+ }
+
+ info = omap_get_config(OMAP_TAG_CLOCK, struct omap_clock_config);
+ if (info != NULL) {
+ if (!cpu_is_omap1510())
+ crystal_type = info->system_clock_type;
+ }
+
+#if defined(CONFIG_ARCH_OMAP730)
+ ck_ref.rate = 13000000;
+#elif defined(CONFIG_ARCH_OMAP16XX)
+ if (crystal_type == 2)
+ ck_ref.rate = 19200000;
+#endif
+
+ printk("Clocks: ARM_SYSST: 0x%04x DPLL_CTL: 0x%04x ARM_CKCTL: 0x%04x\n",
+ omap_readw(ARM_SYSST), omap_readw(DPLL_CTL),
+ omap_readw(ARM_CKCTL));
+
+ /* We want to be in syncronous scalable mode */
+ omap_writew(0x1000, ARM_SYSST);
+
+#ifdef CONFIG_OMAP_CLOCKS_SET_BY_BOOTLOADER
+ /* Use values set by bootloader. Determine PLL rate and recalculate
+ * dependent clocks as if kernel had changed PLL or divisors.
+ */
+ {
+ unsigned pll_ctl_val = omap_readw(DPLL_CTL);
+
+ ck_dpll1.rate = ck_ref.rate; /* Base xtal rate */
+ if (pll_ctl_val & 0x10) {
+ /* PLL enabled, apply multiplier and divisor */
+ if (pll_ctl_val & 0xf80)
+ ck_dpll1.rate *= (pll_ctl_val & 0xf80) >> 7;
+ ck_dpll1.rate /= ((pll_ctl_val & 0x60) >> 5) + 1;
+ } else {
+ /* PLL disabled, apply bypass divisor */
+ switch (pll_ctl_val & 0xc) {
+ case 0:
+ break;
+ case 0x4:
+ ck_dpll1.rate /= 2;
+ break;
+ default:
+ ck_dpll1.rate /= 4;
+ break;
+ }
+ }
+ }
+ propagate_rate(&ck_dpll1);
+#else
+ /* Find the highest supported frequency and enable it */
+ if (omap1_select_table_rate(&virtual_ck_mpu, ~0)) {
+ printk(KERN_ERR "System frequencies not set. Check your config.\n");
+ /* Guess sane values (60MHz) */
+ omap_writew(0x2290, DPLL_CTL);
+ omap_writew(0x1005, ARM_CKCTL);
+ ck_dpll1.rate = 60000000;
+ propagate_rate(&ck_dpll1);
+ }
+#endif
+ /* Cache rates for clocks connected to ck_ref (not dpll1) */
+ propagate_rate(&ck_ref);
+ printk(KERN_INFO "Clocking rate (xtal/DPLL1/MPU): "
+ "%ld.%01ld/%ld.%01ld/%ld.%01ld MHz\n",
+ ck_ref.rate / 1000000, (ck_ref.rate / 100000) % 10,
+ ck_dpll1.rate / 1000000, (ck_dpll1.rate / 100000) % 10,
+ arm_ck.rate / 1000000, (arm_ck.rate / 100000) % 10);
+
+#ifdef CONFIG_MACH_OMAP_PERSEUS2
+ /* Select slicer output as OMAP input clock */
+ omap_writew(omap_readw(OMAP730_PCC_UPLD_CTRL) & ~0x1, OMAP730_PCC_UPLD_CTRL);
+#endif
+
+ /* Turn off DSP and ARM_TIMXO. Make sure ARM_INTHCK is not divided */
+ omap_writew(omap_readw(ARM_CKCTL) & 0x0fff, ARM_CKCTL);
+
+ /* Put DSP/MPUI into reset until needed */
+ omap_writew(0, ARM_RSTCT1);
+ omap_writew(1, ARM_RSTCT2);
+ omap_writew(0x400, ARM_IDLECT1);
+
+ /*
+ * According to OMAP5910 Erratum SYS_DMA_1, bit DMACK_REQ (bit 8)
+ * of the ARM_IDLECT2 register must be set to zero. The power-on
+ * default value of this bit is one.
+ */
+ omap_writew(0x0000, ARM_IDLECT2); /* Turn LCD clock off also */
+
+ /*
+ * Only enable those clocks we will need, let the drivers
+ * enable other clocks as necessary
+ */
+ clk_use(&armper_ck.clk);
+ clk_use(&armxor_ck.clk);
+ clk_use(&armtim_ck.clk); /* This should be done by timer code */
+
+ if (cpu_is_omap1510())
+ clk_enable(&arm_gpio_ck);
+
+ return 0;
+}
+
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap1/clock.h
+ *
+ * Copyright (C) 2004 - 2005 Nokia corporation
+ * Written by Tuukka Tikkanen <tuukka.tikkanen@elektrobit.com>
+ * Based on clocks.h by Tony Lindgren, Gordon McNutt and RidgeRun, Inc
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ARCH_ARM_MACH_OMAP1_CLOCK_H
+#define __ARCH_ARM_MACH_OMAP1_CLOCK_H
+
+static int omap1_clk_enable(struct clk * clk);
+static void omap1_clk_disable(struct clk * clk);
+static void omap1_ckctl_recalc(struct clk * clk);
+static void omap1_watchdog_recalc(struct clk * clk);
+static void omap1_ckctl_recalc_dsp_domain(struct clk * clk);
+static int omap1_clk_enable_dsp_domain(struct clk * clk);
+static int omap1_clk_set_rate_dsp_domain(struct clk * clk, unsigned long rate);
+static void omap1_clk_disable_dsp_domain(struct clk * clk);
+static int omap1_set_uart_rate(struct clk * clk, unsigned long rate);
+static void omap1_uart_recalc(struct clk * clk);
+static int omap1_clk_enable_uart_functional(struct clk * clk);
+static void omap1_clk_disable_uart_functional(struct clk * clk);
+static int omap1_set_ext_clk_rate(struct clk * clk, unsigned long rate);
+static long omap1_round_ext_clk_rate(struct clk * clk, unsigned long rate);
+static void omap1_init_ext_clk(struct clk * clk);
+static int omap1_select_table_rate(struct clk * clk, unsigned long rate);
+static long omap1_round_to_table_rate(struct clk * clk, unsigned long rate);
+static int omap1_clk_use(struct clk *clk);
+static void omap1_clk_unuse(struct clk *clk);
+
+struct mpu_rate {
+ unsigned long rate;
+ unsigned long xtal;
+ unsigned long pll_rate;
+ __u16 ckctl_val;
+ __u16 dpllctl_val;
+};
+
+struct uart_clk {
+ struct clk clk;
+ unsigned long sysc_addr;
+};
+
+/* Provide a method for preventing idling some ARM IDLECT clocks */
+struct arm_idlect1_clk {
+ struct clk clk;
+ unsigned long no_idle_count;
+ __u8 idlect_shift;
+};
+
+/* ARM_CKCTL bit shifts */
+#define CKCTL_PERDIV_OFFSET 0
+#define CKCTL_LCDDIV_OFFSET 2
+#define CKCTL_ARMDIV_OFFSET 4
+#define CKCTL_DSPDIV_OFFSET 6
+#define CKCTL_TCDIV_OFFSET 8
+#define CKCTL_DSPMMUDIV_OFFSET 10
+/*#define ARM_TIMXO 12*/
+#define EN_DSPCK 13
+/*#define ARM_INTHCK_SEL 14*/ /* Divide-by-2 for mpu inth_ck */
+/* DSP_CKCTL bit shifts */
+#define CKCTL_DSPPERDIV_OFFSET 0
+
+/* ARM_IDLECT2 bit shifts */
+#define EN_WDTCK 0
+#define EN_XORPCK 1
+#define EN_PERCK 2
+#define EN_LCDCK 3
+#define EN_LBCK 4 /* Not on 1610/1710 */
+/*#define EN_HSABCK 5*/
+#define EN_APICK 6
+#define EN_TIMCK 7
+#define DMACK_REQ 8
+#define EN_GPIOCK 9 /* Not on 1610/1710 */
+/*#define EN_LBFREECK 10*/
+#define EN_CKOUT_ARM 11
+
+/* ARM_IDLECT3 bit shifts */
+#define EN_OCPI_CK 0
+#define EN_TC1_CK 2
+#define EN_TC2_CK 4
+
+/* DSP_IDLECT2 bit shifts (0,1,2 are same as for ARM_IDLECT2) */
+#define EN_DSPTIMCK 5
+
+/* Various register defines for clock controls scattered around OMAP chip */
+#define USB_MCLK_EN_BIT 4 /* In ULPD_CLKC_CTRL */
+#define USB_HOST_HHC_UHOST_EN 9 /* In MOD_CONF_CTRL_0 */
+#define SWD_ULPD_PLL_CLK_REQ 1 /* In SWD_CLK_DIV_CTRL_SEL */
+#define COM_ULPD_PLL_CLK_REQ 1 /* In COM_CLK_DIV_CTRL_SEL */
+#define SWD_CLK_DIV_CTRL_SEL 0xfffe0874
+#define COM_CLK_DIV_CTRL_SEL 0xfffe0878
+#define SOFT_REQ_REG 0xfffe0834
+#define SOFT_REQ_REG2 0xfffe0880
+
+/*-------------------------------------------------------------------------
+ * Omap1 MPU rate table
+ *-------------------------------------------------------------------------*/
+static struct mpu_rate rate_table[] = {
+ /* MPU MHz, xtal MHz, dpll1 MHz, CKCTL, DPLL_CTL
+ * NOTE: Comment order here is different from bits in CKCTL value:
+ * armdiv, dspdiv, dspmmu, tcdiv, perdiv, lcddiv
+ */
+#if defined(CONFIG_OMAP_ARM_216MHZ)
+ { 216000000, 12000000, 216000000, 0x050d, 0x2910 }, /* 1/1/2/2/2/8 */
+#endif
+#if defined(CONFIG_OMAP_ARM_195MHZ)
+ { 195000000, 13000000, 195000000, 0x050e, 0x2790 }, /* 1/1/2/2/4/8 */
+#endif
+#if defined(CONFIG_OMAP_ARM_192MHZ)
+ { 192000000, 19200000, 192000000, 0x050f, 0x2510 }, /* 1/1/2/2/8/8 */
+ { 192000000, 12000000, 192000000, 0x050f, 0x2810 }, /* 1/1/2/2/8/8 */
+ { 96000000, 12000000, 192000000, 0x055f, 0x2810 }, /* 2/2/2/2/8/8 */
+ { 48000000, 12000000, 192000000, 0x0baf, 0x2810 }, /* 4/4/4/8/8/8 */
+ { 24000000, 12000000, 192000000, 0x0fff, 0x2810 }, /* 8/8/8/8/8/8 */
+#endif
+#if defined(CONFIG_OMAP_ARM_182MHZ)
+ { 182000000, 13000000, 182000000, 0x050e, 0x2710 }, /* 1/1/2/2/4/8 */
+#endif
+#if defined(CONFIG_OMAP_ARM_168MHZ)
+ { 168000000, 12000000, 168000000, 0x010f, 0x2710 }, /* 1/1/1/2/8/8 */
+#endif
+#if defined(CONFIG_OMAP_ARM_150MHZ)
+ { 150000000, 12000000, 150000000, 0x010a, 0x2cb0 }, /* 1/1/1/2/4/4 */
+#endif
+#if defined(CONFIG_OMAP_ARM_120MHZ)
+ { 120000000, 12000000, 120000000, 0x010a, 0x2510 }, /* 1/1/1/2/4/4 */
+#endif
+#if defined(CONFIG_OMAP_ARM_96MHZ)
+ { 96000000, 12000000, 96000000, 0x0005, 0x2410 }, /* 1/1/1/1/2/2 */
+#endif
+#if defined(CONFIG_OMAP_ARM_60MHZ)
+ { 60000000, 12000000, 60000000, 0x0005, 0x2290 }, /* 1/1/1/1/2/2 */
+#endif
+#if defined(CONFIG_OMAP_ARM_30MHZ)
+ { 30000000, 12000000, 60000000, 0x0555, 0x2290 }, /* 2/2/2/2/2/2 */
+#endif
+ { 0, 0, 0, 0, 0 },
+};
+
+/*-------------------------------------------------------------------------
+ * Omap1 clocks
+ *-------------------------------------------------------------------------*/
+
+static struct clk ck_ref = {
+ .name = "ck_ref",
+ .rate = 12000000,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ ALWAYS_ENABLED,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk ck_dpll1 = {
+ .name = "ck_dpll1",
+ .parent = &ck_ref,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ RATE_PROPAGATES | ALWAYS_ENABLED,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct arm_idlect1_clk ck_dpll1out = {
+ .clk = {
+ .name = "ck_dpll1out",
+ .parent = &ck_dpll1,
+ .flags = CLOCK_IN_OMAP16XX | CLOCK_IDLE_CONTROL,
+ .enable_reg = (void __iomem *)ARM_IDLECT2,
+ .enable_bit = EN_CKOUT_ARM,
+ .recalc = &followparent_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+ },
+ .idlect_shift = 12,
+};
+
+static struct clk arm_ck = {
+ .name = "arm_ck",
+ .parent = &ck_dpll1,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ RATE_CKCTL | RATE_PROPAGATES | ALWAYS_ENABLED,
+ .rate_offset = CKCTL_ARMDIV_OFFSET,
+ .recalc = &omap1_ckctl_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct arm_idlect1_clk armper_ck = {
+ .clk = {
+ .name = "armper_ck",
+ .parent = &ck_dpll1,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ RATE_CKCTL | CLOCK_IDLE_CONTROL,
+ .enable_reg = (void __iomem *)ARM_IDLECT2,
+ .enable_bit = EN_PERCK,
+ .rate_offset = CKCTL_PERDIV_OFFSET,
+ .recalc = &omap1_ckctl_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+ },
+ .idlect_shift = 2,
+};
+
+static struct clk arm_gpio_ck = {
+ .name = "arm_gpio_ck",
+ .parent = &ck_dpll1,
+ .flags = CLOCK_IN_OMAP1510,
+ .enable_reg = (void __iomem *)ARM_IDLECT2,
+ .enable_bit = EN_GPIOCK,
+ .recalc = &followparent_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct arm_idlect1_clk armxor_ck = {
+ .clk = {
+ .name = "armxor_ck",
+ .parent = &ck_ref,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ CLOCK_IDLE_CONTROL,
+ .enable_reg = (void __iomem *)ARM_IDLECT2,
+ .enable_bit = EN_XORPCK,
+ .recalc = &followparent_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+ },
+ .idlect_shift = 1,
+};
+
+static struct arm_idlect1_clk armtim_ck = {
+ .clk = {
+ .name = "armtim_ck",
+ .parent = &ck_ref,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ CLOCK_IDLE_CONTROL,
+ .enable_reg = (void __iomem *)ARM_IDLECT2,
+ .enable_bit = EN_TIMCK,
+ .recalc = &followparent_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+ },
+ .idlect_shift = 9,
+};
+
+static struct arm_idlect1_clk armwdt_ck = {
+ .clk = {
+ .name = "armwdt_ck",
+ .parent = &ck_ref,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ CLOCK_IDLE_CONTROL,
+ .enable_reg = (void __iomem *)ARM_IDLECT2,
+ .enable_bit = EN_WDTCK,
+ .recalc = &omap1_watchdog_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+ },
+ .idlect_shift = 0,
+};
+
+static struct clk arminth_ck16xx = {
+ .name = "arminth_ck",
+ .parent = &arm_ck,
+ .flags = CLOCK_IN_OMAP16XX | ALWAYS_ENABLED,
+ .recalc = &followparent_recalc,
+ /* Note: On 16xx the frequency can be divided by 2 by programming
+ * ARM_CKCTL:ARM_INTHCK_SEL(14) to 1
+ *
+ * 1510 version is in TC clocks.
+ */
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk dsp_ck = {
+ .name = "dsp_ck",
+ .parent = &ck_dpll1,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ RATE_CKCTL,
+ .enable_reg = (void __iomem *)ARM_CKCTL,
+ .enable_bit = EN_DSPCK,
+ .rate_offset = CKCTL_DSPDIV_OFFSET,
+ .recalc = &omap1_ckctl_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk dspmmu_ck = {
+ .name = "dspmmu_ck",
+ .parent = &ck_dpll1,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ RATE_CKCTL | ALWAYS_ENABLED,
+ .rate_offset = CKCTL_DSPMMUDIV_OFFSET,
+ .recalc = &omap1_ckctl_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk dspper_ck = {
+ .name = "dspper_ck",
+ .parent = &ck_dpll1,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ RATE_CKCTL | VIRTUAL_IO_ADDRESS,
+ .enable_reg = (void __iomem *)DSP_IDLECT2,
+ .enable_bit = EN_PERCK,
+ .rate_offset = CKCTL_PERDIV_OFFSET,
+ .recalc = &omap1_ckctl_recalc_dsp_domain,
+ .set_rate = &omap1_clk_set_rate_dsp_domain,
+ .enable = &omap1_clk_enable_dsp_domain,
+ .disable = &omap1_clk_disable_dsp_domain,
+};
+
+static struct clk dspxor_ck = {
+ .name = "dspxor_ck",
+ .parent = &ck_ref,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ VIRTUAL_IO_ADDRESS,
+ .enable_reg = (void __iomem *)DSP_IDLECT2,
+ .enable_bit = EN_XORPCK,
+ .recalc = &followparent_recalc,
+ .enable = &omap1_clk_enable_dsp_domain,
+ .disable = &omap1_clk_disable_dsp_domain,
+};
+
+static struct clk dsptim_ck = {
+ .name = "dsptim_ck",
+ .parent = &ck_ref,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ VIRTUAL_IO_ADDRESS,
+ .enable_reg = (void __iomem *)DSP_IDLECT2,
+ .enable_bit = EN_DSPTIMCK,
+ .recalc = &followparent_recalc,
+ .enable = &omap1_clk_enable_dsp_domain,
+ .disable = &omap1_clk_disable_dsp_domain,
+};
+
+/* Tie ARM_IDLECT1:IDLIF_ARM to this logical clock structure */
+static struct arm_idlect1_clk tc_ck = {
+ .clk = {
+ .name = "tc_ck",
+ .parent = &ck_dpll1,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ CLOCK_IN_OMAP730 | RATE_CKCTL |
+ RATE_PROPAGATES | ALWAYS_ENABLED |
+ CLOCK_IDLE_CONTROL,
+ .rate_offset = CKCTL_TCDIV_OFFSET,
+ .recalc = &omap1_ckctl_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+ },
+ .idlect_shift = 6,
+};
+
+static struct clk arminth_ck1510 = {
+ .name = "arminth_ck",
+ .parent = &tc_ck.clk,
+ .flags = CLOCK_IN_OMAP1510 | ALWAYS_ENABLED,
+ .recalc = &followparent_recalc,
+ /* Note: On 1510 the frequency follows TC_CK
+ *
+ * 16xx version is in MPU clocks.
+ */
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk tipb_ck = {
+ /* No-idle controlled by "tc_ck" */
+ .name = "tibp_ck",
+ .parent = &tc_ck.clk,
+ .flags = CLOCK_IN_OMAP1510 | ALWAYS_ENABLED,
+ .recalc = &followparent_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk l3_ocpi_ck = {
+ /* No-idle controlled by "tc_ck" */
+ .name = "l3_ocpi_ck",
+ .parent = &tc_ck.clk,
+ .flags = CLOCK_IN_OMAP16XX,
+ .enable_reg = (void __iomem *)ARM_IDLECT3,
+ .enable_bit = EN_OCPI_CK,
+ .recalc = &followparent_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk tc1_ck = {
+ .name = "tc1_ck",
+ .parent = &tc_ck.clk,
+ .flags = CLOCK_IN_OMAP16XX,
+ .enable_reg = (void __iomem *)ARM_IDLECT3,
+ .enable_bit = EN_TC1_CK,
+ .recalc = &followparent_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk tc2_ck = {
+ .name = "tc2_ck",
+ .parent = &tc_ck.clk,
+ .flags = CLOCK_IN_OMAP16XX,
+ .enable_reg = (void __iomem *)ARM_IDLECT3,
+ .enable_bit = EN_TC2_CK,
+ .recalc = &followparent_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk dma_ck = {
+ /* No-idle controlled by "tc_ck" */
+ .name = "dma_ck",
+ .parent = &tc_ck.clk,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ ALWAYS_ENABLED,
+ .recalc = &followparent_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk dma_lcdfree_ck = {
+ .name = "dma_lcdfree_ck",
+ .parent = &tc_ck.clk,
+ .flags = CLOCK_IN_OMAP16XX | ALWAYS_ENABLED,
+ .recalc = &followparent_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct arm_idlect1_clk api_ck = {
+ .clk = {
+ .name = "api_ck",
+ .parent = &tc_ck.clk,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ CLOCK_IDLE_CONTROL,
+ .enable_reg = (void __iomem *)ARM_IDLECT2,
+ .enable_bit = EN_APICK,
+ .recalc = &followparent_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+ },
+ .idlect_shift = 8,
+};
+
+static struct arm_idlect1_clk lb_ck = {
+ .clk = {
+ .name = "lb_ck",
+ .parent = &tc_ck.clk,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IDLE_CONTROL,
+ .enable_reg = (void __iomem *)ARM_IDLECT2,
+ .enable_bit = EN_LBCK,
+ .recalc = &followparent_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+ },
+ .idlect_shift = 4,
+};
+
+static struct clk rhea1_ck = {
+ .name = "rhea1_ck",
+ .parent = &tc_ck.clk,
+ .flags = CLOCK_IN_OMAP16XX | ALWAYS_ENABLED,
+ .recalc = &followparent_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk rhea2_ck = {
+ .name = "rhea2_ck",
+ .parent = &tc_ck.clk,
+ .flags = CLOCK_IN_OMAP16XX | ALWAYS_ENABLED,
+ .recalc = &followparent_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk lcd_ck_16xx = {
+ .name = "lcd_ck",
+ .parent = &ck_dpll1,
+ .flags = CLOCK_IN_OMAP16XX | CLOCK_IN_OMAP730 | RATE_CKCTL,
+ .enable_reg = (void __iomem *)ARM_IDLECT2,
+ .enable_bit = EN_LCDCK,
+ .rate_offset = CKCTL_LCDDIV_OFFSET,
+ .recalc = &omap1_ckctl_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct arm_idlect1_clk lcd_ck_1510 = {
+ .clk = {
+ .name = "lcd_ck",
+ .parent = &ck_dpll1,
+ .flags = CLOCK_IN_OMAP1510 | RATE_CKCTL |
+ CLOCK_IDLE_CONTROL,
+ .enable_reg = (void __iomem *)ARM_IDLECT2,
+ .enable_bit = EN_LCDCK,
+ .rate_offset = CKCTL_LCDDIV_OFFSET,
+ .recalc = &omap1_ckctl_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+ },
+ .idlect_shift = 3,
+};
+
+static struct clk uart1_1510 = {
+ .name = "uart1_ck",
+ /* Direct from ULPD, no real parent */
+ .parent = &armper_ck.clk,
+ .rate = 12000000,
+ .flags = CLOCK_IN_OMAP1510 | ENABLE_REG_32BIT |
+ ALWAYS_ENABLED | CLOCK_NO_IDLE_PARENT,
+ .enable_reg = (void __iomem *)MOD_CONF_CTRL_0,
+ .enable_bit = 29, /* Chooses between 12MHz and 48MHz */
+ .set_rate = &omap1_set_uart_rate,
+ .recalc = &omap1_uart_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct uart_clk uart1_16xx = {
+ .clk = {
+ .name = "uart1_ck",
+ /* Direct from ULPD, no real parent */
+ .parent = &armper_ck.clk,
+ .rate = 48000000,
+ .flags = CLOCK_IN_OMAP16XX | RATE_FIXED |
+ ENABLE_REG_32BIT | CLOCK_NO_IDLE_PARENT,
+ .enable_reg = (void __iomem *)MOD_CONF_CTRL_0,
+ .enable_bit = 29,
+ .enable = &omap1_clk_enable_uart_functional,
+ .disable = &omap1_clk_disable_uart_functional,
+ },
+ .sysc_addr = 0xfffb0054,
+};
+
+static struct clk uart2_ck = {
+ .name = "uart2_ck",
+ /* Direct from ULPD, no real parent */
+ .parent = &armper_ck.clk,
+ .rate = 12000000,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ ENABLE_REG_32BIT | ALWAYS_ENABLED |
+ CLOCK_NO_IDLE_PARENT,
+ .enable_reg = (void __iomem *)MOD_CONF_CTRL_0,
+ .enable_bit = 30, /* Chooses between 12MHz and 48MHz */
+ .set_rate = &omap1_set_uart_rate,
+ .recalc = &omap1_uart_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk uart3_1510 = {
+ .name = "uart3_ck",
+ /* Direct from ULPD, no real parent */
+ .parent = &armper_ck.clk,
+ .rate = 12000000,
+ .flags = CLOCK_IN_OMAP1510 | ENABLE_REG_32BIT |
+ ALWAYS_ENABLED | CLOCK_NO_IDLE_PARENT,
+ .enable_reg = (void __iomem *)MOD_CONF_CTRL_0,
+ .enable_bit = 31, /* Chooses between 12MHz and 48MHz */
+ .set_rate = &omap1_set_uart_rate,
+ .recalc = &omap1_uart_recalc,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct uart_clk uart3_16xx = {
+ .clk = {
+ .name = "uart3_ck",
+ /* Direct from ULPD, no real parent */
+ .parent = &armper_ck.clk,
+ .rate = 48000000,
+ .flags = CLOCK_IN_OMAP16XX | RATE_FIXED |
+ ENABLE_REG_32BIT | CLOCK_NO_IDLE_PARENT,
+ .enable_reg = (void __iomem *)MOD_CONF_CTRL_0,
+ .enable_bit = 31,
+ .enable = &omap1_clk_enable_uart_functional,
+ .disable = &omap1_clk_disable_uart_functional,
+ },
+ .sysc_addr = 0xfffb9854,
+};
+
+static struct clk usb_clko = { /* 6 MHz output on W4_USB_CLKO */
+ .name = "usb_clko",
+ /* Direct from ULPD, no parent */
+ .rate = 6000000,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ RATE_FIXED | ENABLE_REG_32BIT,
+ .enable_reg = (void __iomem *)ULPD_CLOCK_CTRL,
+ .enable_bit = USB_MCLK_EN_BIT,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk usb_hhc_ck1510 = {
+ .name = "usb_hhc_ck",
+ /* Direct from ULPD, no parent */
+ .rate = 48000000, /* Actually 2 clocks, 12MHz and 48MHz */
+ .flags = CLOCK_IN_OMAP1510 |
+ RATE_FIXED | ENABLE_REG_32BIT,
+ .enable_reg = (void __iomem *)MOD_CONF_CTRL_0,
+ .enable_bit = USB_HOST_HHC_UHOST_EN,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk usb_hhc_ck16xx = {
+ .name = "usb_hhc_ck",
+ /* Direct from ULPD, no parent */
+ .rate = 48000000,
+ /* OTG_SYSCON_2.OTG_PADEN == 0 (not 1510-compatible) */
+ .flags = CLOCK_IN_OMAP16XX |
+ RATE_FIXED | ENABLE_REG_32BIT,
+ .enable_reg = (void __iomem *)OTG_BASE + 0x08 /* OTG_SYSCON_2 */,
+ .enable_bit = 8 /* UHOST_EN */,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk usb_dc_ck = {
+ .name = "usb_dc_ck",
+ /* Direct from ULPD, no parent */
+ .rate = 48000000,
+ .flags = CLOCK_IN_OMAP16XX | RATE_FIXED,
+ .enable_reg = (void __iomem *)SOFT_REQ_REG,
+ .enable_bit = 4,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk mclk_1510 = {
+ .name = "mclk",
+ /* Direct from ULPD, no parent. May be enabled by ext hardware. */
+ .rate = 12000000,
+ .flags = CLOCK_IN_OMAP1510 | RATE_FIXED,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk mclk_16xx = {
+ .name = "mclk",
+ /* Direct from ULPD, no parent. May be enabled by ext hardware. */
+ .flags = CLOCK_IN_OMAP16XX,
+ .enable_reg = (void __iomem *)COM_CLK_DIV_CTRL_SEL,
+ .enable_bit = COM_ULPD_PLL_CLK_REQ,
+ .set_rate = &omap1_set_ext_clk_rate,
+ .round_rate = &omap1_round_ext_clk_rate,
+ .init = &omap1_init_ext_clk,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk bclk_1510 = {
+ .name = "bclk",
+ /* Direct from ULPD, no parent. May be enabled by ext hardware. */
+ .rate = 12000000,
+ .flags = CLOCK_IN_OMAP1510 | RATE_FIXED,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk bclk_16xx = {
+ .name = "bclk",
+ /* Direct from ULPD, no parent. May be enabled by ext hardware. */
+ .flags = CLOCK_IN_OMAP16XX,
+ .enable_reg = (void __iomem *)SWD_CLK_DIV_CTRL_SEL,
+ .enable_bit = SWD_ULPD_PLL_CLK_REQ,
+ .set_rate = &omap1_set_ext_clk_rate,
+ .round_rate = &omap1_round_ext_clk_rate,
+ .init = &omap1_init_ext_clk,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk mmc1_ck = {
+ .name = "mmc1_ck",
+ /* Functional clock is direct from ULPD, interface clock is ARMPER */
+ .parent = &armper_ck.clk,
+ .rate = 48000000,
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ RATE_FIXED | ENABLE_REG_32BIT | CLOCK_NO_IDLE_PARENT,
+ .enable_reg = (void __iomem *)MOD_CONF_CTRL_0,
+ .enable_bit = 23,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk mmc2_ck = {
+ .name = "mmc2_ck",
+ /* Functional clock is direct from ULPD, interface clock is ARMPER */
+ .parent = &armper_ck.clk,
+ .rate = 48000000,
+ .flags = CLOCK_IN_OMAP16XX |
+ RATE_FIXED | ENABLE_REG_32BIT | CLOCK_NO_IDLE_PARENT,
+ .enable_reg = (void __iomem *)MOD_CONF_CTRL_0,
+ .enable_bit = 20,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk virtual_ck_mpu = {
+ .name = "mpu",
+ .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
+ VIRTUAL_CLOCK | ALWAYS_ENABLED,
+ .parent = &arm_ck, /* Is smarter alias for */
+ .recalc = &followparent_recalc,
+ .set_rate = &omap1_select_table_rate,
+ .round_rate = &omap1_round_to_table_rate,
+ .enable = &omap1_clk_enable,
+ .disable = &omap1_clk_disable,
+};
+
+static struct clk * onchip_clks[] = {
+ /* non-ULPD clocks */
+ &ck_ref,
+ &ck_dpll1,
+ /* CK_GEN1 clocks */
+ &ck_dpll1out.clk,
+ &arm_ck,
+ &armper_ck.clk,
+ &arm_gpio_ck,
+ &armxor_ck.clk,
+ &armtim_ck.clk,
+ &armwdt_ck.clk,
+ &arminth_ck1510, &arminth_ck16xx,
+ /* CK_GEN2 clocks */
+ &dsp_ck,
+ &dspmmu_ck,
+ &dspper_ck,
+ &dspxor_ck,
+ &dsptim_ck,
+ /* CK_GEN3 clocks */
+ &tc_ck.clk,
+ &tipb_ck,
+ &l3_ocpi_ck,
+ &tc1_ck,
+ &tc2_ck,
+ &dma_ck,
+ &dma_lcdfree_ck,
+ &api_ck.clk,
+ &lb_ck.clk,
+ &rhea1_ck,
+ &rhea2_ck,
+ &lcd_ck_16xx,
+ &lcd_ck_1510.clk,
+ /* ULPD clocks */
+ &uart1_1510,
+ &uart1_16xx.clk,
+ &uart2_ck,
+ &uart3_1510,
+ &uart3_16xx.clk,
+ &usb_clko,
+ &usb_hhc_ck1510, &usb_hhc_ck16xx,
+ &usb_dc_ck,
+ &mclk_1510, &mclk_16xx,
+ &bclk_1510, &bclk_16xx,
+ &mmc1_ck,
+ &mmc2_ck,
+ /* Virtual clocks */
+ &virtual_ck_mpu,
+};
+
+#endif
#include <asm/arch/mux.h>
#include <asm/arch/gpio.h>
-
-static void omap_nop_release(struct device *dev)
-{
- /* Nothing */
-}
-
-/*-------------------------------------------------------------------------*/
-
-#if defined(CONFIG_I2C_OMAP) || defined(CONFIG_I2C_OMAP_MODULE)
-
-#define OMAP_I2C_BASE 0xfffb3800
-
-static struct resource i2c_resources[] = {
- {
- .start = OMAP_I2C_BASE,
- .end = OMAP_I2C_BASE + 0x3f,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = INT_I2C,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-/* DMA not used; works around erratum writing to non-empty i2c fifo */
-
-static struct platform_device omap_i2c_device = {
- .name = "i2c_omap",
- .id = -1,
- .dev = {
- .release = omap_nop_release,
- },
- .num_resources = ARRAY_SIZE(i2c_resources),
- .resource = i2c_resources,
-};
-
-static void omap_init_i2c(void)
-{
- /* FIXME define and use a boot tag, in case of boards that
- * either don't wire up I2C, or chips that mux it differently...
- * it can include clocking and address info, maybe more.
- */
- omap_cfg_reg(I2C_SCL);
- omap_cfg_reg(I2C_SDA);
-
- (void) platform_device_register(&omap_i2c_device);
-}
-#else
-static inline void omap_init_i2c(void) {}
-#endif
+extern void omap_nop_release(struct device *dev);
/*-------------------------------------------------------------------------*/
/*-------------------------------------------------------------------------*/
-#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
-
-#define OMAP_MMC1_BASE 0xfffb7800
-#define OMAP_MMC2_BASE 0xfffb7c00 /* omap16xx only */
-
-static struct omap_mmc_conf mmc1_conf;
-
-static u64 mmc1_dmamask = 0xffffffff;
-
-static struct resource mmc1_resources[] = {
- {
- .start = IO_ADDRESS(OMAP_MMC1_BASE),
- .end = IO_ADDRESS(OMAP_MMC1_BASE) + 0x7f,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = INT_MMC,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device mmc_omap_device1 = {
- .name = "mmci-omap",
- .id = 1,
- .dev = {
- .release = omap_nop_release,
- .dma_mask = &mmc1_dmamask,
- .platform_data = &mmc1_conf,
- },
- .num_resources = ARRAY_SIZE(mmc1_resources),
- .resource = mmc1_resources,
-};
-
-#ifdef CONFIG_ARCH_OMAP16XX
-
-static struct omap_mmc_conf mmc2_conf;
-
-static u64 mmc2_dmamask = 0xffffffff;
-
-static struct resource mmc2_resources[] = {
- {
- .start = IO_ADDRESS(OMAP_MMC2_BASE),
- .end = IO_ADDRESS(OMAP_MMC2_BASE) + 0x7f,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = INT_1610_MMC2,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device mmc_omap_device2 = {
- .name = "mmci-omap",
- .id = 2,
- .dev = {
- .release = omap_nop_release,
- .dma_mask = &mmc2_dmamask,
- .platform_data = &mmc2_conf,
- },
- .num_resources = ARRAY_SIZE(mmc2_resources),
- .resource = mmc2_resources,
-};
-#endif
-
-static void __init omap_init_mmc(void)
-{
- const struct omap_mmc_config *mmc_conf;
- const struct omap_mmc_conf *mmc;
-
- /* NOTE: assumes MMC was never (wrongly) enabled */
- mmc_conf = omap_get_config(OMAP_TAG_MMC, struct omap_mmc_config);
- if (!mmc_conf)
- return;
-
- /* block 1 is always available and has just one pinout option */
- mmc = &mmc_conf->mmc[0];
- if (mmc->enabled) {
- omap_cfg_reg(MMC_CMD);
- omap_cfg_reg(MMC_CLK);
- omap_cfg_reg(MMC_DAT0);
- if (cpu_is_omap1710()) {
- omap_cfg_reg(M15_1710_MMC_CLKI);
- omap_cfg_reg(P19_1710_MMC_CMDDIR);
- omap_cfg_reg(P20_1710_MMC_DATDIR0);
- }
- if (mmc->wire4) {
- omap_cfg_reg(MMC_DAT1);
- /* NOTE: DAT2 can be on W10 (here) or M15 */
- if (!mmc->nomux)
- omap_cfg_reg(MMC_DAT2);
- omap_cfg_reg(MMC_DAT3);
- }
- mmc1_conf = *mmc;
- (void) platform_device_register(&mmc_omap_device1);
- }
-
-#ifdef CONFIG_ARCH_OMAP16XX
- /* block 2 is on newer chips, and has many pinout options */
- mmc = &mmc_conf->mmc[1];
- if (mmc->enabled) {
- if (!mmc->nomux) {
- omap_cfg_reg(Y8_1610_MMC2_CMD);
- omap_cfg_reg(Y10_1610_MMC2_CLK);
- omap_cfg_reg(R18_1610_MMC2_CLKIN);
- omap_cfg_reg(W8_1610_MMC2_DAT0);
- if (mmc->wire4) {
- omap_cfg_reg(V8_1610_MMC2_DAT1);
- omap_cfg_reg(W15_1610_MMC2_DAT2);
- omap_cfg_reg(R10_1610_MMC2_DAT3);
- }
-
- /* These are needed for the level shifter */
- omap_cfg_reg(V9_1610_MMC2_CMDDIR);
- omap_cfg_reg(V5_1610_MMC2_DATDIR0);
- omap_cfg_reg(W19_1610_MMC2_DATDIR1);
- }
-
- /* Feedback clock must be set on OMAP-1710 MMC2 */
- if (cpu_is_omap1710())
- omap_writel(omap_readl(MOD_CONF_CTRL_1) | (1 << 24),
- MOD_CONF_CTRL_1);
- mmc2_conf = *mmc;
- (void) platform_device_register(&mmc_omap_device2);
- }
-#endif
- return;
-}
-#else
-static inline void omap_init_mmc(void) {}
-#endif
-
#if defined(CONFIG_OMAP_RTC) || defined(CONFIG_OMAP_RTC)
#define OMAP_RTC_BASE 0xfffb4800
static inline void omap_init_rtc(void) {}
#endif
-/*-------------------------------------------------------------------------*/
-
-#if defined(CONFIG_OMAP16XX_WATCHDOG) || defined(CONFIG_OMAP16XX_WATCHDOG_MODULE)
-
-#define OMAP_WDT_BASE 0xfffeb000
-
-static struct resource wdt_resources[] = {
- {
- .start = OMAP_WDT_BASE,
- .end = OMAP_WDT_BASE + 0x4f,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device omap_wdt_device = {
- .name = "omap1610_wdt",
- .id = -1,
- .dev = {
- .release = omap_nop_release,
- },
- .num_resources = ARRAY_SIZE(wdt_resources),
- .resource = wdt_resources,
-};
-
-static void omap_init_wdt(void)
-{
- (void) platform_device_register(&omap_wdt_device);
-}
-#else
-static inline void omap_init_wdt(void) {}
-#endif
-
/*-------------------------------------------------------------------------*/
* may be handled by the boot loader, and drivers should expect it will
* normally have been done by the time they're probed.
*/
-static int __init omap_init_devices(void)
+static int __init omap1_init_devices(void)
{
/* please keep these calls, and their implementations above,
* in alphabetical order so they're easier to sort through.
*/
- omap_init_i2c();
omap_init_irda();
- omap_init_mmc();
omap_init_rtc();
- omap_init_wdt();
return 0;
}
-arch_initcall(omap_init_devices);
+arch_initcall(omap1_init_devices);
#include <asm/io.h>
+#define OMAP_DIE_ID_0 0xfffe1800
+#define OMAP_DIE_ID_1 0xfffe1804
+#define OMAP_PRODUCTION_ID_0 0xfffe2000
+#define OMAP_PRODUCTION_ID_1 0xfffe2004
+#define OMAP32_ID_0 0xfffed400
+#define OMAP32_ID_1 0xfffed404
+
struct omap_id {
u16 jtag_id; /* Used to determine OMAP type */
u8 die_rev; /* Processor revision */
/* Register values to detect the OMAP version */
static struct omap_id omap_ids[] __initdata = {
+ { .jtag_id = 0xb574, .die_rev = 0x2, .omap_id = 0x03310315, .type = 0x03100000},
{ .jtag_id = 0x355f, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x07300100},
{ .jtag_id = 0xb55f, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x07300300},
{ .jtag_id = 0xb470, .die_rev = 0x0, .omap_id = 0x03310100, .type = 0x15100000},
case 0x07:
system_rev |= 0x07;
break;
+ case 0x03:
case 0x15:
system_rev |= 0x15;
break;
#include <asm/mach/map.h>
#include <asm/io.h>
+#include <asm/arch/mux.h>
#include <asm/arch/tc.h>
-extern int clk_init(void);
+extern int omap1_clk_init(void);
extern void omap_check_revision(void);
extern void omap_sram_init(void);
};
#endif
-#ifdef CONFIG_ARCH_OMAP1510
+#ifdef CONFIG_ARCH_OMAP15XX
static struct map_desc omap1510_io_desc[] __initdata = {
{
.virtual = OMAP1510_DSP_BASE,
iotable_init(omap730_io_desc, ARRAY_SIZE(omap730_io_desc));
}
#endif
-#ifdef CONFIG_ARCH_OMAP1510
+#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
iotable_init(omap1510_io_desc, ARRAY_SIZE(omap1510_io_desc));
}
/* Must init clocks early to assure that timer interrupt works
*/
- clk_init();
+ omap1_clk_init();
}
/*
*/
void __init omap_map_common_io(void)
{
- if (!initialized)
+ if (!initialized) {
_omap_map_io();
+ omap1_mux_init();
+ }
}
#include <asm/irq.h>
#include <asm/mach/irq.h>
#include <asm/arch/gpio.h>
+#include <asm/arch/cpu.h>
#include <asm/io.h>
};
#endif
-#ifdef CONFIG_ARCH_OMAP1510
+#ifdef CONFIG_ARCH_OMAP15XX
static struct omap_irq_bank omap1510_irq_banks[] = {
{ .base_reg = OMAP_IH1_BASE, .trigger_map = 0xb3febfff },
{ .base_reg = OMAP_IH2_BASE, .trigger_map = 0xffbfffed },
};
+static struct omap_irq_bank omap310_irq_banks[] = {
+ { .base_reg = OMAP_IH1_BASE, .trigger_map = 0xb3faefc3 },
+ { .base_reg = OMAP_IH2_BASE, .trigger_map = 0x65b3c061 },
+};
#endif
#if defined(CONFIG_ARCH_OMAP16XX)
irq_bank_count = ARRAY_SIZE(omap730_irq_banks);
}
#endif
-#ifdef CONFIG_ARCH_OMAP1510
+#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
irq_banks = omap1510_irq_banks;
irq_bank_count = ARRAY_SIZE(omap1510_irq_banks);
}
+ if (cpu_is_omap310()) {
+ irq_banks = omap310_irq_banks;
+ irq_bank_count = ARRAY_SIZE(omap310_irq_banks);
+ }
#endif
#if defined(CONFIG_ARCH_OMAP16XX)
if (cpu_is_omap16xx()) {
}
/* Unmask level 2 handler */
- if (cpu_is_omap730()) {
+
+ if (cpu_is_omap730())
omap_unmask_irq(INT_730_IH2_IRQ);
- } else {
- omap_unmask_irq(INT_IH2_IRQ);
- }
+ else if (cpu_is_omap1510())
+ omap_unmask_irq(INT_1510_IH2_IRQ);
+ else if (cpu_is_omap16xx())
+ omap_unmask_irq(INT_1610_IH2_IRQ);
}
#include <asm/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
+#include <asm/mach-types.h>
#include <asm/arch/fpga.h>
#include <asm/arch/gpio.h>
case led_stop:
case led_halted:
/* all leds off during suspend or shutdown */
- omap_set_gpio_dataout(GPIO_TIMER, 0);
- omap_set_gpio_dataout(GPIO_IDLE, 0);
+
+ if (! machine_is_omap_perseus2()) {
+ omap_set_gpio_dataout(GPIO_TIMER, 0);
+ omap_set_gpio_dataout(GPIO_IDLE, 0);
+ }
+
__raw_writew(~0, &fpga->leds);
led_state &= ~LED_STATE_ENABLED;
if (evt == led_halted) {
iounmap(fpga);
fpga = NULL;
}
+
goto done;
case led_claim:
#ifdef CONFIG_LEDS_TIMER
case led_timer:
led_state ^= LED_TIMER_ON;
- omap_set_gpio_dataout(GPIO_TIMER, led_state & LED_TIMER_ON);
- goto done;
+
+ if (machine_is_omap_perseus2())
+ hw_led_state ^= H2P2_DBG_FPGA_P2_LED_TIMER;
+ else {
+ omap_set_gpio_dataout(GPIO_TIMER, led_state & LED_TIMER_ON);
+ goto done;
+ }
+
+ break;
#endif
#ifdef CONFIG_LEDS_CPU
case led_idle_start:
- omap_set_gpio_dataout(GPIO_IDLE, 1);
- goto done;
+ if (machine_is_omap_perseus2())
+ hw_led_state |= H2P2_DBG_FPGA_P2_LED_IDLE;
+ else {
+ omap_set_gpio_dataout(GPIO_IDLE, 1);
+ goto done;
+ }
+
+ break;
case led_idle_end:
- omap_set_gpio_dataout(GPIO_IDLE, 0);
- goto done;
+ if (machine_is_omap_perseus2())
+ hw_led_state &= ~H2P2_DBG_FPGA_P2_LED_IDLE;
+ else {
+ omap_set_gpio_dataout(GPIO_IDLE, 0);
+ goto done;
+ }
+
+ break;
#endif
case led_green_on:
/*
* Actually burn the LEDs
*/
- if (led_state & LED_STATE_CLAIMED)
+ if (led_state & LED_STATE_ENABLED)
__raw_writew(~hw_led_state, &fpga->leds);
done:
if (machine_is_omap_h2()
|| machine_is_omap_h3()
- || machine_is_omap_perseus2()
#ifdef CONFIG_OMAP_OSK_MISTRAL
|| machine_is_omap_osk()
#endif
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap1/mux.c
+ *
+ * OMAP1 pin multiplexing configurations
+ *
+ * Copyright (C) 2003 - 2005 Nokia Corporation
+ *
+ * Written by Tony Lindgren <tony.lindgren@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <asm/system.h>
+#include <asm/io.h>
+#include <linux/spinlock.h>
+
+#include <asm/arch/mux.h>
+
+#ifdef CONFIG_OMAP_MUX
+
+#ifdef CONFIG_ARCH_OMAP730
+struct pin_config __initdata_or_module omap730_pins[] = {
+MUX_CFG_730("E2_730_KBR0", 12, 21, 0, 0, 20, 1, NA, 0, 0)
+MUX_CFG_730("J7_730_KBR1", 12, 25, 0, 0, 24, 1, NA, 0, 0)
+MUX_CFG_730("E1_730_KBR2", 12, 29, 0, 0, 28, 1, NA, 0, 0)
+MUX_CFG_730("F3_730_KBR3", 13, 1, 0, 0, 0, 1, NA, 0, 0)
+MUX_CFG_730("D2_730_KBR4", 13, 5, 0, 0, 4, 1, NA, 0, 0)
+MUX_CFG_730("C2_730_KBC0", 13, 9, 0, 0, 8, 1, NA, 0, 0)
+MUX_CFG_730("D3_730_KBC1", 13, 13, 0, 0, 12, 1, NA, 0, 0)
+MUX_CFG_730("E4_730_KBC2", 13, 17, 0, 0, 16, 1, NA, 0, 0)
+MUX_CFG_730("F4_730_KBC3", 13, 21, 0, 0, 20, 1, NA, 0, 0)
+MUX_CFG_730("E3_730_KBC4", 13, 25, 0, 0, 24, 1, NA, 0, 0)
+};
+#endif
+
+#if defined(CONFIG_ARCH_OMAP15XX) || defined(CONFIG_ARCH_OMAP16XX)
+struct pin_config __initdata_or_module omap1xxx_pins[] = {
+/*
+ * description mux mode mux pull pull pull pu_pd pu dbg
+ * reg offset mode reg bit ena reg
+ */
+MUX_CFG("UART1_TX", 9, 21, 1, 2, 3, 0, NA, 0, 0)
+MUX_CFG("UART1_RTS", 9, 12, 1, 2, 0, 0, NA, 0, 0)
+
+/* UART2 (COM_UART_GATING), conflicts with USB2 */
+MUX_CFG("UART2_TX", C, 27, 1, 3, 3, 0, NA, 0, 0)
+MUX_CFG("UART2_RX", C, 18, 0, 3, 1, 1, NA, 0, 0)
+MUX_CFG("UART2_CTS", C, 21, 0, 3, 1, 1, NA, 0, 0)
+MUX_CFG("UART2_RTS", C, 24, 1, 3, 2, 0, NA, 0, 0)
+
+/* UART3 (GIGA_UART_GATING) */
+MUX_CFG("UART3_TX", 6, 0, 1, 0, 30, 0, NA, 0, 0)
+MUX_CFG("UART3_RX", 6, 3, 0, 0, 31, 1, NA, 0, 0)
+MUX_CFG("UART3_CTS", 5, 12, 2, 0, 24, 0, NA, 0, 0)
+MUX_CFG("UART3_RTS", 5, 15, 2, 0, 25, 0, NA, 0, 0)
+MUX_CFG("UART3_CLKREQ", 9, 27, 0, 2, 5, 0, NA, 0, 0)
+MUX_CFG("UART3_BCLK", A, 0, 0, 2, 6, 0, NA, 0, 0)
+MUX_CFG("Y15_1610_UART3_RTS", A, 0, 1, 2, 6, 0, NA, 0, 0)
+
+/* PWT & PWL, conflicts with UART3 */
+MUX_CFG("PWT", 6, 0, 2, 0, 30, 0, NA, 0, 0)
+MUX_CFG("PWL", 6, 3, 1, 0, 31, 1, NA, 0, 0)
+
+/* USB internal master generic */
+MUX_CFG("R18_USB_VBUS", 7, 9, 2, 1, 11, 0, NA, 0, 1)
+MUX_CFG("R18_1510_USB_GPIO0", 7, 9, 0, 1, 11, 1, NA, 0, 1)
+/* works around erratum: W4_USB_PUEN and W4_USB_PUDIS are switched! */
+MUX_CFG("W4_USB_PUEN", D, 3, 3, 3, 5, 1, NA, 0, 1)
+MUX_CFG("W4_USB_CLKO", D, 3, 1, 3, 5, 0, NA, 0, 1)
+MUX_CFG("W4_USB_HIGHZ", D, 3, 4, 3, 5, 0, 3, 0, 1)
+MUX_CFG("W4_GPIO58", D, 3, 7, 3, 5, 0, 3, 0, 1)
+
+/* USB1 master */
+MUX_CFG("USB1_SUSP", 8, 27, 2, 1, 27, 0, NA, 0, 1)
+MUX_CFG("USB1_SE0", 9, 0, 2, 1, 28, 0, NA, 0, 1)
+MUX_CFG("W13_1610_USB1_SE0", 9, 0, 4, 1, 28, 0, NA, 0, 1)
+MUX_CFG("USB1_TXEN", 9, 3, 2, 1, 29, 0, NA, 0, 1)
+MUX_CFG("USB1_TXD", 9, 24, 1, 2, 4, 0, NA, 0, 1)
+MUX_CFG("USB1_VP", A, 3, 1, 2, 7, 0, NA, 0, 1)
+MUX_CFG("USB1_VM", A, 6, 1, 2, 8, 0, NA, 0, 1)
+MUX_CFG("USB1_RCV", A, 9, 1, 2, 9, 0, NA, 0, 1)
+MUX_CFG("USB1_SPEED", A, 12, 2, 2, 10, 0, NA, 0, 1)
+MUX_CFG("R13_1610_USB1_SPEED", A, 12, 5, 2, 10, 0, NA, 0, 1)
+MUX_CFG("R13_1710_USB1_SEO", A, 12, 5, 2, 10, 0, NA, 0, 1)
+
+/* USB2 master */
+MUX_CFG("USB2_SUSP", B, 3, 1, 2, 17, 0, NA, 0, 1)
+MUX_CFG("USB2_VP", B, 6, 1, 2, 18, 0, NA, 0, 1)
+MUX_CFG("USB2_TXEN", B, 9, 1, 2, 19, 0, NA, 0, 1)
+MUX_CFG("USB2_VM", C, 18, 1, 3, 0, 0, NA, 0, 1)
+MUX_CFG("USB2_RCV", C, 21, 1, 3, 1, 0, NA, 0, 1)
+MUX_CFG("USB2_SE0", C, 24, 2, 3, 2, 0, NA, 0, 1)
+MUX_CFG("USB2_TXD", C, 27, 2, 3, 3, 0, NA, 0, 1)
+
+/* OMAP-1510 GPIO */
+MUX_CFG("R18_1510_GPIO0", 7, 9, 0, 1, 11, 1, 0, 0, 1)
+MUX_CFG("R19_1510_GPIO1", 7, 6, 0, 1, 10, 1, 0, 0, 1)
+MUX_CFG("M14_1510_GPIO2", 7, 3, 0, 1, 9, 1, 0, 0, 1)
+
+/* OMAP1610 GPIO */
+MUX_CFG("P18_1610_GPIO3", 7, 0, 0, 1, 8, 0, NA, 0, 1)
+MUX_CFG("Y15_1610_GPIO17", A, 0, 7, 2, 6, 0, NA, 0, 1)
+
+/* OMAP-1710 GPIO */
+MUX_CFG("R18_1710_GPIO0", 7, 9, 0, 1, 11, 1, 1, 1, 1)
+MUX_CFG("V2_1710_GPIO10", F, 27, 1, 4, 3, 1, 4, 1, 1)
+MUX_CFG("N21_1710_GPIO14", 6, 9, 0, 1, 1, 1, 1, 1, 1)
+MUX_CFG("W15_1710_GPIO40", 9, 27, 7, 2, 5, 1, 2, 1, 1)
+
+/* MPUIO */
+MUX_CFG("MPUIO2", 7, 18, 0, 1, 14, 1, NA, 0, 1)
+MUX_CFG("N15_1610_MPUIO2", 7, 18, 0, 1, 14, 1, 1, 0, 1)
+MUX_CFG("MPUIO4", 7, 15, 0, 1, 13, 1, NA, 0, 1)
+MUX_CFG("MPUIO5", 7, 12, 0, 1, 12, 1, NA, 0, 1)
+
+MUX_CFG("T20_1610_MPUIO5", 7, 12, 0, 1, 12, 0, 3, 0, 1)
+MUX_CFG("W11_1610_MPUIO6", 10, 15, 2, 3, 8, 0, 3, 0, 1)
+MUX_CFG("V10_1610_MPUIO7", A, 24, 2, 2, 14, 0, 2, 0, 1)
+MUX_CFG("W11_1610_MPUIO9", 10, 15, 1, 3, 8, 0, 3, 0, 1)
+MUX_CFG("V10_1610_MPUIO10", A, 24, 1, 2, 14, 0, 2, 0, 1)
+MUX_CFG("W10_1610_MPUIO11", A, 18, 2, 2, 11, 0, 2, 0, 1)
+MUX_CFG("E20_1610_MPUIO13", 3, 21, 1, 0, 7, 0, 0, 0, 1)
+MUX_CFG("U20_1610_MPUIO14", 9, 6, 6, 0, 30, 0, 0, 0, 1)
+MUX_CFG("E19_1610_MPUIO15", 3, 18, 1, 0, 6, 0, 0, 0, 1)
+
+/* MCBSP2 */
+MUX_CFG("MCBSP2_CLKR", C, 6, 0, 2, 27, 1, NA, 0, 1)
+MUX_CFG("MCBSP2_CLKX", C, 9, 0, 2, 29, 1, NA, 0, 1)
+MUX_CFG("MCBSP2_DR", C, 0, 0, 2, 26, 1, NA, 0, 1)
+MUX_CFG("MCBSP2_DX", C, 15, 0, 2, 31, 1, NA, 0, 1)
+MUX_CFG("MCBSP2_FSR", C, 12, 0, 2, 30, 1, NA, 0, 1)
+MUX_CFG("MCBSP2_FSX", C, 3, 0, 2, 27, 1, NA, 0, 1)
+
+/* MCBSP3 NOTE: Mode must 1 for clock */
+MUX_CFG("MCBSP3_CLKX", 9, 3, 1, 1, 29, 0, NA, 0, 1)
+
+/* Misc ballouts */
+MUX_CFG("BALLOUT_V8_ARMIO3", B, 18, 0, 2, 25, 1, NA, 0, 1)
+MUX_CFG("N20_HDQ", 6, 18, 1, 1, 4, 0, 1, 4, 0)
+
+/* OMAP-1610 MMC2 */
+MUX_CFG("W8_1610_MMC2_DAT0", B, 21, 6, 2, 23, 1, 2, 1, 1)
+MUX_CFG("V8_1610_MMC2_DAT1", B, 27, 6, 2, 25, 1, 2, 1, 1)
+MUX_CFG("W15_1610_MMC2_DAT2", 9, 12, 6, 2, 5, 1, 2, 1, 1)
+MUX_CFG("R10_1610_MMC2_DAT3", B, 18, 6, 2, 22, 1, 2, 1, 1)
+MUX_CFG("Y10_1610_MMC2_CLK", B, 3, 6, 2, 17, 0, 2, 0, 1)
+MUX_CFG("Y8_1610_MMC2_CMD", B, 24, 6, 2, 24, 1, 2, 1, 1)
+MUX_CFG("V9_1610_MMC2_CMDDIR", B, 12, 6, 2, 20, 0, 2, 1, 1)
+MUX_CFG("V5_1610_MMC2_DATDIR0", B, 15, 6, 2, 21, 0, 2, 1, 1)
+MUX_CFG("W19_1610_MMC2_DATDIR1", 8, 15, 6, 1, 23, 0, 1, 1, 1)
+MUX_CFG("R18_1610_MMC2_CLKIN", 7, 9, 6, 1, 11, 0, 1, 11, 1)
+
+/* OMAP-1610 External Trace Interface */
+MUX_CFG("M19_1610_ETM_PSTAT0", 5, 27, 1, 0, 29, 0, 0, 0, 1)
+MUX_CFG("L15_1610_ETM_PSTAT1", 5, 24, 1, 0, 28, 0, 0, 0, 1)
+MUX_CFG("L18_1610_ETM_PSTAT2", 5, 21, 1, 0, 27, 0, 0, 0, 1)
+MUX_CFG("L19_1610_ETM_D0", 5, 18, 1, 0, 26, 0, 0, 0, 1)
+MUX_CFG("J19_1610_ETM_D6", 5, 0, 1, 0, 20, 0, 0, 0, 1)
+MUX_CFG("J18_1610_ETM_D7", 5, 27, 1, 0, 19, 0, 0, 0, 1)
+
+/* OMAP16XX GPIO */
+MUX_CFG("P20_1610_GPIO4", 6, 27, 0, 1, 7, 0, 1, 1, 1)
+MUX_CFG("V9_1610_GPIO7", B, 12, 1, 2, 20, 0, 2, 1, 1)
+MUX_CFG("W8_1610_GPIO9", B, 21, 0, 2, 23, 0, 2, 1, 1)
+MUX_CFG("N20_1610_GPIO11", 6, 18, 0, 1, 4, 0, 1, 1, 1)
+MUX_CFG("N19_1610_GPIO13", 6, 12, 0, 1, 2, 0, 1, 1, 1)
+MUX_CFG("P10_1610_GPIO22", C, 0, 7, 2, 26, 0, 2, 1, 1)
+MUX_CFG("V5_1610_GPIO24", B, 15, 7, 2, 21, 0, 2, 1, 1)
+MUX_CFG("AA20_1610_GPIO_41", 9, 9, 7, 1, 31, 0, 1, 1, 1)
+MUX_CFG("W19_1610_GPIO48", 8, 15, 7, 1, 23, 1, 1, 0, 1)
+MUX_CFG("M7_1610_GPIO62", 10, 0, 0, 4, 24, 0, 4, 0, 1)
+MUX_CFG("V14_16XX_GPIO37", 9, 18, 7, 2, 2, 0, 2, 2, 0)
+MUX_CFG("R9_16XX_GPIO18", C, 18, 7, 3, 0, 0, 3, 0, 0)
+MUX_CFG("L14_16XX_GPIO49", 6, 3, 7, 0, 31, 0, 0, 31, 0)
+
+/* OMAP-1610 uWire */
+MUX_CFG("V19_1610_UWIRE_SCLK", 8, 6, 0, 1, 20, 0, 1, 1, 1)
+MUX_CFG("U18_1610_UWIRE_SDI", 8, 0, 0, 1, 18, 0, 1, 1, 1)
+MUX_CFG("W21_1610_UWIRE_SDO", 8, 3, 0, 1, 19, 0, 1, 1, 1)
+MUX_CFG("N14_1610_UWIRE_CS0", 8, 9, 1, 1, 21, 0, 1, 1, 1)
+MUX_CFG("P15_1610_UWIRE_CS3", 8, 12, 1, 1, 22, 0, 1, 1, 1)
+MUX_CFG("N15_1610_UWIRE_CS1", 7, 18, 2, 1, 14, 0, NA, 0, 1)
+
+/* OMAP-1610 Flash */
+MUX_CFG("L3_1610_FLASH_CS2B_OE",10, 6, 1, NA, 0, 0, NA, 0, 1)
+MUX_CFG("M8_1610_FLASH_CS2B_WE",10, 3, 1, NA, 0, 0, NA, 0, 1)
+
+/* First MMC interface, same on 1510, 1610 and 1710 */
+MUX_CFG("MMC_CMD", A, 27, 0, 2, 15, 1, 2, 1, 1)
+MUX_CFG("MMC_DAT1", A, 24, 0, 2, 14, 1, 2, 1, 1)
+MUX_CFG("MMC_DAT2", A, 18, 0, 2, 12, 1, 2, 1, 1)
+MUX_CFG("MMC_DAT0", B, 0, 0, 2, 16, 1, 2, 1, 1)
+MUX_CFG("MMC_CLK", A, 21, 0, NA, 0, 0, NA, 0, 1)
+MUX_CFG("MMC_DAT3", 10, 15, 0, 3, 8, 1, 3, 1, 1)
+MUX_CFG("M15_1710_MMC_CLKI", 6, 21, 2, 0, 0, 0, NA, 0, 1)
+MUX_CFG("P19_1710_MMC_CMDDIR", 6, 24, 6, 0, 0, 0, NA, 0, 1)
+MUX_CFG("P20_1710_MMC_DATDIR0", 6, 27, 5, 0, 0, 0, NA, 0, 1)
+
+/* OMAP-1610 USB0 alternate configuration */
+MUX_CFG("W9_USB0_TXEN", B, 9, 5, 2, 19, 0, 2, 0, 1)
+MUX_CFG("AA9_USB0_VP", B, 6, 5, 2, 18, 0, 2, 0, 1)
+MUX_CFG("Y5_USB0_RCV", C, 21, 5, 3, 1, 0, 1, 0, 1)
+MUX_CFG("R9_USB0_VM", C, 18, 5, 3, 0, 0, 3, 0, 1)
+MUX_CFG("V6_USB0_TXD", C, 27, 5, 3, 3, 0, 3, 0, 1)
+MUX_CFG("W5_USB0_SE0", C, 24, 5, 3, 2, 0, 3, 0, 1)
+MUX_CFG("V9_USB0_SPEED", B, 12, 5, 2, 20, 0, 2, 0, 1)
+MUX_CFG("Y10_USB0_SUSP", B, 3, 5, 2, 17, 0, 2, 0, 1)
+
+/* USB2 interface */
+MUX_CFG("W9_USB2_TXEN", B, 9, 1, NA, 0, 0, NA, 0, 1)
+MUX_CFG("AA9_USB2_VP", B, 6, 1, NA, 0, 0, NA, 0, 1)
+MUX_CFG("Y5_USB2_RCV", C, 21, 1, NA, 0, 0, NA, 0, 1)
+MUX_CFG("R9_USB2_VM", C, 18, 1, NA, 0, 0, NA, 0, 1)
+MUX_CFG("V6_USB2_TXD", C, 27, 2, NA, 0, 0, NA, 0, 1)
+MUX_CFG("W5_USB2_SE0", C, 24, 2, NA, 0, 0, NA, 0, 1)
+
+/* 16XX UART */
+MUX_CFG("R13_1610_UART1_TX", A, 12, 6, 2, 10, 0, 2, 10, 1)
+MUX_CFG("V14_16XX_UART1_RX", 9, 18, 0, 2, 2, 0, 2, 2, 1)
+MUX_CFG("R14_1610_UART1_CTS", 9, 15, 0, 2, 1, 0, 2, 1, 1)
+MUX_CFG("AA15_1610_UART1_RTS", 9, 12, 1, 2, 0, 0, 2, 0, 1)
+MUX_CFG("R9_16XX_UART2_RX", C, 18, 0, 3, 0, 0, 3, 0, 1)
+MUX_CFG("L14_16XX_UART3_RX", 6, 3, 0, 0, 31, 0, 0, 31, 1)
+
+/* I2C interface */
+MUX_CFG("I2C_SCL", 7, 24, 0, NA, 0, 0, NA, 0, 0)
+MUX_CFG("I2C_SDA", 7, 27, 0, NA, 0, 0, NA, 0, 0)
+
+/* Keypad */
+MUX_CFG("F18_1610_KBC0", 3, 15, 0, 0, 5, 1, 0, 0, 0)
+MUX_CFG("D20_1610_KBC1", 3, 12, 0, 0, 4, 1, 0, 0, 0)
+MUX_CFG("D19_1610_KBC2", 3, 9, 0, 0, 3, 1, 0, 0, 0)
+MUX_CFG("E18_1610_KBC3", 3, 6, 0, 0, 2, 1, 0, 0, 0)
+MUX_CFG("C21_1610_KBC4", 3, 3, 0, 0, 1, 1, 0, 0, 0)
+MUX_CFG("G18_1610_KBR0", 4, 0, 0, 0, 10, 1, 0, 1, 0)
+MUX_CFG("F19_1610_KBR1", 3, 27, 0, 0, 9, 1, 0, 1, 0)
+MUX_CFG("H14_1610_KBR2", 3, 24, 0, 0, 8, 1, 0, 1, 0)
+MUX_CFG("E20_1610_KBR3", 3, 21, 0, 0, 7, 1, 0, 1, 0)
+MUX_CFG("E19_1610_KBR4", 3, 18, 0, 0, 6, 1, 0, 1, 0)
+MUX_CFG("N19_1610_KBR5", 6, 12, 1, 1, 2, 1, 1, 1, 0)
+
+/* Power management */
+MUX_CFG("T20_1610_LOW_PWR", 7, 12, 1, NA, 0, 0, NA, 0, 0)
+
+/* MCLK Settings */
+MUX_CFG("V5_1710_MCLK_ON", B, 15, 0, NA, 0, 0, NA, 0, 0)
+MUX_CFG("V5_1710_MCLK_OFF", B, 15, 6, NA, 0, 0, NA, 0, 0)
+MUX_CFG("R10_1610_MCLK_ON", B, 18, 0, NA, 22, 0, NA, 1, 0)
+MUX_CFG("R10_1610_MCLK_OFF", B, 18, 6, 2, 22, 1, 2, 1, 1)
+
+/* CompactFlash controller, conflicts with MMC1 */
+MUX_CFG("P11_1610_CF_CD2", A, 27, 3, 2, 15, 1, 2, 1, 1)
+MUX_CFG("R11_1610_CF_IOIS16", B, 0, 3, 2, 16, 1, 2, 1, 1)
+MUX_CFG("V10_1610_CF_IREQ", A, 24, 3, 2, 14, 0, 2, 0, 1)
+MUX_CFG("W10_1610_CF_RESET", A, 18, 3, 2, 12, 1, 2, 1, 1)
+MUX_CFG("W11_1610_CF_CD1", 10, 15, 3, 3, 8, 1, 3, 1, 1)
+};
+#endif /* CONFIG_ARCH_OMAP15XX || CONFIG_ARCH_OMAP16XX */
+
+int __init omap1_mux_init(void)
+{
+
+#ifdef CONFIG_ARCH_OMAP730
+ omap_mux_register(omap730_pins, ARRAY_SIZE(omap730_pins));
+#endif
+
+#if defined(CONFIG_ARCH_OMAP15XX) || defined(CONFIG_ARCH_OMAP16XX)
+ omap_mux_register(omap1xxx_pins, ARRAY_SIZE(omap1xxx_pins));
+#endif
+
+ return 0;
+}
+
+#endif
* By default UART2 does not work on Innovator-1510 if you have
* USB OHCI enabled. To use UART2, you must disable USB2 first.
*/
-void __init omap_serial_init(int ports[OMAP_MAX_NR_PORTS])
+void __init omap_serial_init(void)
{
int i;
+ const struct omap_uart_config *info;
if (cpu_is_omap730()) {
serial_platform_data[0].regshift = 0;
serial_platform_data[2].uartclk = OMAP1510_BASE_BAUD * 16;
}
+ info = omap_get_config(OMAP_TAG_UART, struct omap_uart_config);
+ if (info == NULL)
+ return;
+
for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
unsigned char reg;
- if (ports[i] == 0) {
+ if (!((1 << i) & info->enabled_uarts)) {
serial_platform_data[i].membase = NULL;
serial_platform_data[i].mapbase = 0;
continue;
#ifdef CONFIG_OMAP_32K_TIMER
-#ifdef CONFIG_ARCH_OMAP1510
-#error OMAP 32KHz timer does not currently work on 1510!
+#ifdef CONFIG_ARCH_OMAP15XX
+#error OMAP 32KHz timer does not currently work on 15XX!
#endif
/*
# ARM925T
config CPU_ARM925T
bool "Support ARM925T processor" if ARCH_OMAP1
- depends on ARCH_OMAP1510
- default y if ARCH_OMAP1510
+ depends on ARCH_OMAP15XX
+ default y if ARCH_OMAP15XX
select CPU_32v4
select CPU_ABRT_EV4T
select CPU_CACHE_V4WT
projects / linux-2.6-omap-h63xx.git / commitdiff