endchoice
+choice
+ prompt "Used baseboard"
+ depends on MACH_PCM027
+
+config MACH_PCM990_BASEBOARD
+ bool "PHYTEC PCM-990 development board"
+
+endchoice
+
if PXA_SHARPSL
choice
obj-$(CONFIG_MACH_AKITA) += akita-ioexp.o
obj-$(CONFIG_MACH_POODLE) += poodle.o corgi_ssp.o
obj-$(CONFIG_MACH_PCM027) += pcm027.o
+obj-$(CONFIG_MACH_PCM990_BASEBOARD) += pcm990-baseboard.o
obj-$(CONFIG_MACH_TOSA) += tosa.o
obj-$(CONFIG_MACH_EM_X270) += em-x270.o
obj-$(CONFIG_MACH_MAGICIAN) += magician.o
--- /dev/null
+/*
+ * arch/arm/mach-pxa/pcm990-baseboard.c
+ * Support for the Phytec phyCORE-PXA270 Development Platform (PCM-990).
+ *
+ * Refer
+ * http://www.phytec.com/products/rdk/ARM-XScale/phyCORE-XScale-PXA270.html
+ * for additional hardware info
+ *
+ * Author: Juergen Kilb
+ * Created: April 05, 2005
+ * Copyright: Phytec Messtechnik GmbH
+ * e-Mail: armlinux@phytec.de
+ *
+ * based on Intel Mainstone Board
+ *
+ * Copyright 2007 Juergen Beisert @ Pengutronix (j.beisert@pengutronix.de)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/irq.h>
+#include <linux/platform_device.h>
+#include <linux/ide.h>
+#include <asm/mach/map.h>
+#include <asm/arch/pxa-regs.h>
+#include <asm/arch/mmc.h>
+#include <asm/arch/ohci.h>
+#include <asm/arch/pcm990_baseboard.h>
+
+/*
+ * The PCM-990 development baseboard uses PCM-027's hardeware in the
+ * following way:
+ *
+ * - LCD support is in use
+ * - GPIO16 is output for back light on/off with PWM
+ * - GPIO58 ... GPIO73 are outputs for display data
+ * - GPIO74 is output output for LCDFCLK
+ * - GPIO75 is output for LCDLCLK
+ * - GPIO76 is output for LCDPCLK
+ * - GPIO77 is output for LCDBIAS
+ * - MMC support is in use
+ * - GPIO32 is output for MMCCLK
+ * - GPIO92 is MMDAT0
+ * - GPIO109 is MMDAT1
+ * - GPIO110 is MMCS0
+ * - GPIO111 is MMCS1
+ * - GPIO112 is MMCMD
+ * - IDE/CF card is in use
+ * - GPIO48 is output /POE
+ * - GPIO49 is output /PWE
+ * - GPIO50 is output /PIOR
+ * - GPIO51 is output /PIOW
+ * - GPIO54 is output /PCE2
+ * - GPIO55 is output /PREG
+ * - GPIO56 is input /PWAIT
+ * - GPIO57 is output /PIOS16
+ * - GPIO79 is output PSKTSEL
+ * - GPIO85 is output /PCE1
+ * - FFUART is in use
+ * - GPIO34 is input FFRXD
+ * - GPIO35 is input FFCTS
+ * - GPIO36 is input FFDCD
+ * - GPIO37 is input FFDSR
+ * - GPIO38 is input FFRI
+ * - GPIO39 is output FFTXD
+ * - GPIO40 is output FFDTR
+ * - GPIO41 is output FFRTS
+ * - BTUART is in use
+ * - GPIO42 is input BTRXD
+ * - GPIO43 is output BTTXD
+ * - GPIO44 is input BTCTS
+ * - GPIO45 is output BTRTS
+ * - IRUART is in use
+ * - GPIO46 is input STDRXD
+ * - GPIO47 is output STDTXD
+ * - AC97 is in use*)
+ * - GPIO28 is input AC97CLK
+ * - GPIO29 is input AC97DatIn
+ * - GPIO30 is output AC97DatO
+ * - GPIO31 is output AC97SYNC
+ * - GPIO113 is output AC97_RESET
+ * - SSP is in use
+ * - GPIO23 is output SSPSCLK
+ * - GPIO24 is output chip select to Max7301
+ * - GPIO25 is output SSPTXD
+ * - GPIO26 is input SSPRXD
+ * - GPIO27 is input for Max7301 IRQ
+ * - GPIO53 is input SSPSYSCLK
+ * - SSP3 is in use
+ * - GPIO81 is output SSPTXD3
+ * - GPIO82 is input SSPRXD3
+ * - GPIO83 is output SSPSFRM
+ * - GPIO84 is output SSPCLK3
+ *
+ * Otherwise claimed GPIOs:
+ * GPIO1 -> IRQ from user switch
+ * GPIO9 -> IRQ from power management
+ * GPIO10 -> IRQ from WML9712 AC97 controller
+ * GPIO11 -> IRQ from IDE controller
+ * GPIO12 -> IRQ from CF controller
+ * GPIO13 -> IRQ from CF controller
+ * GPIO14 -> GPIO free
+ * GPIO15 -> /CS1 selects baseboard's Control CPLD (U7, 16 bit wide data path)
+ * GPIO19 -> GPIO free
+ * GPIO20 -> /SDCS2
+ * GPIO21 -> /CS3 PC card socket select
+ * GPIO33 -> /CS5 network controller select
+ * GPIO78 -> /CS2 (16 bit wide data path)
+ * GPIO80 -> /CS4 (16 bit wide data path)
+ * GPIO86 -> GPIO free
+ * GPIO87 -> GPIO free
+ * GPIO90 -> LED0 on CPU module
+ * GPIO91 -> LED1 on CPI module
+ * GPIO117 -> SCL
+ * GPIO118 -> SDA
+ */
+
+static unsigned long pcm990_irq_enabled;
+
+static void pcm990_mask_ack_irq(unsigned int irq)
+{
+ int pcm990_irq = (irq - PCM027_IRQ(0));
+ PCM990_INTMSKENA = (pcm990_irq_enabled &= ~(1 << pcm990_irq));
+}
+
+static void pcm990_unmask_irq(unsigned int irq)
+{
+ int pcm990_irq = (irq - PCM027_IRQ(0));
+ /* the irq can be acknowledged only if deasserted, so it's done here */
+ PCM990_INTSETCLR |= 1 << pcm990_irq;
+ PCM990_INTMSKENA = (pcm990_irq_enabled |= (1 << pcm990_irq));
+}
+
+static struct irq_chip pcm990_irq_chip = {
+ .mask_ack = pcm990_mask_ack_irq,
+ .unmask = pcm990_unmask_irq,
+};
+
+static void pcm990_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+ unsigned long pending = (~PCM990_INTSETCLR) & pcm990_irq_enabled;
+
+ do {
+ GEDR(PCM990_CTRL_INT_IRQ_GPIO) =
+ GPIO_bit(PCM990_CTRL_INT_IRQ_GPIO);
+ if (likely(pending)) {
+ irq = PCM027_IRQ(0) + __ffs(pending);
+ desc = irq_desc + irq;
+ desc_handle_irq(irq, desc);
+ }
+ pending = (~PCM990_INTSETCLR) & pcm990_irq_enabled;
+ } while (pending);
+}
+
+static void __init pcm990_init_irq(void)
+{
+ int irq;
+
+ /* setup extra PCM990 irqs */
+ for (irq = PCM027_IRQ(0); irq <= PCM027_IRQ(3); irq++) {
+ set_irq_chip(irq, &pcm990_irq_chip);
+ set_irq_handler(irq, handle_level_irq);
+ set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+ }
+
+ PCM990_INTMSKENA = 0x00; /* disable all Interrupts */
+ PCM990_INTSETCLR = 0xFF;
+
+ set_irq_chained_handler(PCM990_CTRL_INT_IRQ, pcm990_irq_handler);
+ set_irq_type(PCM990_CTRL_INT_IRQ, PCM990_CTRL_INT_IRQ_EDGE);
+}
+
+static int pcm990_mci_init(struct device *dev, irq_handler_t mci_detect_int,
+ void *data)
+{
+ int err;
+
+ /*
+ * enable GPIO for PXA27x MMC controller
+ */
+ pxa_gpio_mode(GPIO32_MMCCLK_MD);
+ pxa_gpio_mode(GPIO112_MMCCMD_MD);
+ pxa_gpio_mode(GPIO92_MMCDAT0_MD);
+ pxa_gpio_mode(GPIO109_MMCDAT1_MD);
+ pxa_gpio_mode(GPIO110_MMCDAT2_MD);
+ pxa_gpio_mode(GPIO111_MMCDAT3_MD);
+
+ err = request_irq(PCM027_MMCDET_IRQ, mci_detect_int, IRQF_DISABLED,
+ "MMC card detect", data);
+ if (err)
+ printk(KERN_ERR "pcm990_mci_init: MMC/SD: can't request MMC "
+ "card detect IRQ\n");
+
+ return err;
+}
+
+static void pcm990_mci_setpower(struct device *dev, unsigned int vdd)
+{
+ struct pxamci_platform_data *p_d = dev->platform_data;
+
+ if ((1 << vdd) & p_d->ocr_mask)
+ __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG5) =
+ PCM990_CTRL_MMC2PWR;
+ else
+ __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG5) =
+ ~PCM990_CTRL_MMC2PWR;
+}
+
+static void pcm990_mci_exit(struct device *dev, void *data)
+{
+ free_irq(PCM027_MMCDET_IRQ, data);
+}
+
+#define MSECS_PER_JIFFY (1000/HZ)
+
+static struct pxamci_platform_data pcm990_mci_platform_data = {
+ .detect_delay = 250 / MSECS_PER_JIFFY,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .init = pcm990_mci_init,
+ .setpower = pcm990_mci_setpower,
+ .exit = pcm990_mci_exit,
+};
+
+/*
+ * init OHCI hardware to work with
+ *
+ * Note: Only USB port 1 (host only) is connected
+ *
+ * GPIO88 (USBHPWR#1): overcurrent in, overcurrent when low
+ * GPIO89 (USBHPEN#1): power-on out, on when low
+ */
+static int pcm990_ohci_init(struct device *dev)
+{
+ pxa_gpio_mode(PCM990_USB_OVERCURRENT);
+ pxa_gpio_mode(PCM990_USB_PWR_EN);
+ /*
+ * disable USB port 2 and 3
+ * power sense is active low
+ */
+ UHCHR = ((UHCHR) | UHCHR_PCPL | UHCHR_PSPL | UHCHR_SSEP2 |
+ UHCHR_SSEP3) & ~(UHCHR_SSEP1 | UHCHR_SSE);
+ /*
+ * wait 10ms after Power on
+ * overcurrent per port
+ * power switch per port
+ */
+ UHCRHDA = (5<<24) | (1<<11) | (1<<8); /* FIXME: Required? */
+
+ return 0;
+}
+
+static struct pxaohci_platform_data pcm990_ohci_platform_data = {
+ .port_mode = PMM_PERPORT_MODE,
+ .init = pcm990_ohci_init,
+ .exit = NULL,
+};
+
+/*
+ * AC97 support
+ * Note: The connected AC97 mixer also reports interrupts at PCM990_AC97_IRQ
+ */
+static struct resource pxa27x_ac97_resources[] = {
+ [0] = {
+ .start = 0x40500000,
+ .end = 0x40500000 + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_AC97,
+ .end = IRQ_AC97,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static u64 pxa_ac97_dmamask = 0xffffffffUL;
+
+static struct platform_device pxa27x_device_ac97 = {
+ .name = "pxa2xx-ac97",
+ .id = -1,
+ .dev = {
+ .dma_mask = &pxa_ac97_dmamask,
+ .coherent_dma_mask = 0xffffffff,
+ },
+ .num_resources = ARRAY_SIZE(pxa27x_ac97_resources),
+ .resource = pxa27x_ac97_resources,
+};
+
+/*
+ * enable generic access to the base board control CPLDs U6 and U7
+ */
+static struct map_desc pcm990_io_desc[] __initdata = {
+ {
+ .virtual = PCM990_CTRL_BASE,
+ .pfn = __phys_to_pfn(PCM990_CTRL_PHYS),
+ .length = PCM990_CTRL_SIZE,
+ .type = MT_DEVICE /* CPLD */
+ }, {
+ .virtual = PCM990_CF_PLD_BASE,
+ .pfn = __phys_to_pfn(PCM990_CF_PLD_PHYS),
+ .length = PCM990_CF_PLD_SIZE,
+ .type = MT_DEVICE /* CPLD */
+ }
+};
+
+/*
+ * system init for baseboard usage. Will be called by pcm027 init.
+ *
+ * Add platform devices present on this baseboard and init
+ * them from CPU side as far as required to use them later on
+ */
+void __init pcm990_baseboard_init(void)
+{
+ /* register CPLD access */
+ iotable_init(pcm990_io_desc, ARRAY_SIZE(pcm990_io_desc));
+
+ /* register CPLD's IRQ controller */
+ pcm990_init_irq();
+
+ platform_device_register(&pxa27x_device_ac97);
+
+ /* MMC */
+ pxa_set_mci_info(&pcm990_mci_platform_data);
+
+ /* USB host */
+ pxa_set_ohci_info(&pcm990_ohci_platform_data);
+
+ printk(KERN_INFO"PCM-990 Evaluation baseboard initialized\n");
+}
--- /dev/null
+/*
+ * include/asm-arm/arch-pxa/pcm990_baseboard.h
+ *
+ * (c) 2003 Phytec Messtechnik GmbH <armlinux@phytec.de>
+ * (c) 2007 Juergen Beisert <j.beisert@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <asm/arch/pcm027.h>
+
+/*
+ * definitions relevant only when the PCM-990
+ * development base board is in use
+ */
+
+/* CPLD's interrupt controller is connected to PCM-027 GPIO 9 */
+#define PCM990_CTRL_INT_IRQ_GPIO 9
+#define PCM990_CTRL_INT_IRQ IRQ_GPIO(PCM990_CTRL_INT_IRQ_GPIO)
+#define PCM990_CTRL_INT_IRQ_EDGE IRQT_RISING
+#define PCM990_CTRL_PHYS PXA_CS1_PHYS /* 16-Bit */
+#define PCM990_CTRL_BASE 0xea000000
+#define PCM990_CTRL_SIZE (1*1024*1024)
+
+#define PCM990_CTRL_PWR_IRQ_GPIO 14
+#define PCM990_CTRL_PWR_IRQ IRQ_GPIO(PCM990_CTRL_PWR_IRQ_GPIO)
+#define PCM990_CTRL_PWR_IRQ_EDGE IRQT_RISING
+
+/* visible CPLD (U7) registers */
+#define PCM990_CTRL_REG0 0x0000 /* RESET REGISTER */
+#define PCM990_CTRL_SYSRES 0x0001 /* System RESET REGISTER */
+#define PCM990_CTRL_RESOUT 0x0002 /* RESETOUT Enable REGISTER */
+#define PCM990_CTRL_RESGPIO 0x0004 /* RESETGPIO Enable REGISTER */
+
+#define PCM990_CTRL_REG1 0x0002 /* Power REGISTER */
+#define PCM990_CTRL_5VOFF 0x0001 /* Disable 5V Regulators */
+#define PCM990_CTRL_CANPWR 0x0004 /* Enable CANPWR ADUM */
+#define PCM990_CTRL_PM_5V 0x0008 /* Read 5V OK */
+
+#define PCM990_CTRL_REG2 0x0004 /* LED REGISTER */
+#define PCM990_CTRL_LEDPWR 0x0001 /* POWER LED enable */
+#define PCM990_CTRL_LEDBAS 0x0002 /* BASIS LED enable */
+#define PCM990_CTRL_LEDUSR 0x0004 /* USER LED enable */
+
+#define PCM990_CTRL_REG3 0x0006 /* LCD CTRL REGISTER 3 */
+#define PCM990_CTRL_LCDPWR 0x0001 /* RW LCD Power on */
+#define PCM990_CTRL_LCDON 0x0002 /* RW LCD Latch on */
+#define PCM990_CTRL_LCDPOS1 0x0004 /* RW POS 1 */
+#define PCM990_CTRL_LCDPOS2 0x0008 /* RW POS 2 */
+
+#define PCM990_CTRL_REG4 0x0008 /* MMC1 CTRL REGISTER 4 */
+#define PCM990_CTRL_MMC1PWR 0x0001 /* RW MMC1 Power on */
+
+#define PCM990_CTRL_REG5 0x000A /* MMC2 CTRL REGISTER 5 */
+#define PCM990_CTRL_MMC2PWR 0x0001 /* RW MMC2 Power on */
+#define PCM990_CTRL_MMC2LED 0x0002 /* RW MMC2 LED */
+#define PCM990_CTRL_MMC2DE 0x0004 /* R MMC2 Card detect */
+#define PCM990_CTRL_MMC2WP 0x0008 /* R MMC2 Card write protect */
+
+#define PCM990_CTRL_REG6 0x000C /* Interrupt Clear REGISTER */
+#define PCM990_CTRL_INTC0 0x0001 /* Clear Reg BT Detect */
+#define PCM990_CTRL_INTC1 0x0002 /* Clear Reg FR RI */
+#define PCM990_CTRL_INTC2 0x0004 /* Clear Reg MMC1 Detect */
+#define PCM990_CTRL_INTC3 0x0008 /* Clear Reg PM_5V off */
+
+#define PCM990_CTRL_REG7 0x000E /* Interrupt Enable REGISTER */
+#define PCM990_CTRL_ENAINT0 0x0001 /* Enable Int BT Detect */
+#define PCM990_CTRL_ENAINT1 0x0002 /* Enable Int FR RI */
+#define PCM990_CTRL_ENAINT2 0x0004 /* Enable Int MMC1 Detect */
+#define PCM990_CTRL_ENAINT3 0x0008 /* Enable Int PM_5V off */
+
+#define PCM990_CTRL_REG8 0x0014 /* Uart REGISTER */
+#define PCM990_CTRL_FFSD 0x0001 /* BT Uart Enable */
+#define PCM990_CTRL_BTSD 0x0002 /* FF Uart Enable */
+#define PCM990_CTRL_FFRI 0x0004 /* FF Uart RI detect */
+#define PCM990_CTRL_BTRX 0x0008 /* BT Uart Rx detect */
+
+#define PCM990_CTRL_REG9 0x0010 /* AC97 Flash REGISTER */
+#define PCM990_CTRL_FLWP 0x0001 /* pC Flash Write Protect */
+#define PCM990_CTRL_FLDIS 0x0002 /* pC Flash Disable */
+#define PCM990_CTRL_AC97ENA 0x0004 /* Enable AC97 Expansion */
+
+#define PCM990_CTRL_REG10 0x0012 /* GPS-REGISTER */
+#define PCM990_CTRL_GPSPWR 0x0004 /* GPS-Modul Power on */
+#define PCM990_CTRL_GPSENA 0x0008 /* GPS-Modul Enable */
+
+#define PCM990_CTRL_REG11 0x0014 /* Accu REGISTER */
+#define PCM990_CTRL_ACENA 0x0001 /* Charge Enable */
+#define PCM990_CTRL_ACSEL 0x0002 /* Charge Akku -> DC Enable */
+#define PCM990_CTRL_ACPRES 0x0004 /* DC Present */
+#define PCM990_CTRL_ACALARM 0x0008 /* Error Akku */
+
+#define PCM990_CTRL_P2V(x) ((x) - PCM990_CTRL_PHYS + PCM990_CTRL_BASE)
+#define PCM990_CTRL_V2P(x) ((x) - PCM990_CTRL_BASE + PCM990_CTRL_PHYS)
+
+#ifndef __ASSEMBLY__
+# define __PCM990_CTRL_REG(x) \
+ (*((volatile unsigned char *)PCM990_CTRL_P2V(x)))
+#else
+# define __PCM990_CTRL_REG(x) PCM990_CTRL_P2V(x)
+#endif
+
+#define PCM990_INTMSKENA __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG7)
+#define PCM990_INTSETCLR __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG6)
+#define PCM990_CTRL0 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG0)
+#define PCM990_CTRL1 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG1)
+#define PCM990_CTRL2 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG2)
+#define PCM990_CTRL3 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3)
+#define PCM990_CTRL4 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG4)
+#define PCM990_CTRL5 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG5)
+#define PCM990_CTRL6 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG6)
+#define PCM990_CTRL7 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG7)
+#define PCM990_CTRL8 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG8)
+#define PCM990_CTRL9 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG9)
+#define PCM990_CTRL10 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG10)
+#define PCM990_CTRL11 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG11)
+
+
+/*
+ * IDE
+ */
+#define PCM990_IDE_IRQ_GPIO 13
+#define PCM990_IDE_IRQ IRQ_GPIO(PCM990_IDE_IRQ_GPIO)
+#define PCM990_IDE_IRQ_EDGE IRQT_RISING
+#define PCM990_IDE_PLD_PHYS 0x20000000 /* 16 bit wide */
+#define PCM990_IDE_PLD_BASE 0xee000000
+#define PCM990_IDE_PLD_SIZE (1*1024*1024)
+
+/* visible CPLD (U6) registers */
+#define PCM990_IDE_PLD_REG0 0x1000 /* OFFSET IDE REGISTER 0 */
+#define PCM990_IDE_PM5V 0x0004 /* R System VCC_5V */
+#define PCM990_IDE_STBY 0x0008 /* R System StandBy */
+
+#define PCM990_IDE_PLD_REG1 0x1002 /* OFFSET IDE REGISTER 1 */
+#define PCM990_IDE_IDEMODE 0x0001 /* R TrueIDE Mode */
+#define PCM990_IDE_DMAENA 0x0004 /* RW DMA Enable */
+#define PCM990_IDE_DMA1_0 0x0008 /* RW 1=DREQ1 0=DREQ0 */
+
+#define PCM990_IDE_PLD_REG2 0x1004 /* OFFSET IDE REGISTER 2 */
+#define PCM990_IDE_RESENA 0x0001 /* RW IDE Reset Bit enable */
+#define PCM990_IDE_RES 0x0002 /* RW IDE Reset Bit */
+#define PCM990_IDE_RDY 0x0008 /* RDY */
+
+#define PCM990_IDE_PLD_REG3 0x1006 /* OFFSET IDE REGISTER 3 */
+#define PCM990_IDE_IDEOE 0x0001 /* RW Latch on Databus */
+#define PCM990_IDE_IDEON 0x0002 /* RW Latch on Control Address */
+#define PCM990_IDE_IDEIN 0x0004 /* RW Latch on Interrupt usw. */
+
+#define PCM990_IDE_PLD_REG4 0x1008 /* OFFSET IDE REGISTER 4 */
+#define PCM990_IDE_PWRENA 0x0001 /* RW IDE Power enable */
+#define PCM990_IDE_5V 0x0002 /* R IDE Power 5V */
+#define PCM990_IDE_PWG 0x0008 /* R IDE Power is on */
+
+#define PCM990_IDE_PLD_P2V(x) ((x) - PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_BASE)
+#define PCM990_IDE_PLD_V2P(x) ((x) - PCM990_IDE_PLD_BASE + PCM990_IDE_PLD_PHYS)
+
+#ifndef __ASSEMBLY__
+# define __PCM990_IDE_PLD_REG(x) \
+ (*((volatile unsigned char *)PCM990_IDE_PLD_P2V(x)))
+#else
+# define __PCM990_IDE_PLD_REG(x) PCM990_IDE_PLD_P2V(x)
+#endif
+
+#define PCM990_IDE0 \
+ __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG0)
+#define PCM990_IDE1 \
+ __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG1)
+#define PCM990_IDE2 \
+ __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG2)
+#define PCM990_IDE3 \
+ __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG3)
+#define PCM990_IDE4 \
+ __PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG4)
+
+/*
+ * Compact Flash
+ */
+#define PCM990_CF_IRQ_GPIO 11
+#define PCM990_CF_IRQ IRQ_GPIO(PCM990_CF_IRQ_GPIO)
+#define PCM990_CF_IRQ_EDGE IRQT_RISING
+
+#define PCM990_CF_CD_GPIO 12
+#define PCM990_CF_CD IRQ_GPIO(PCM990_CF_CD_GPIO)
+#define PCM990_CF_CD_EDGE IRQT_RISING
+
+#define PCM990_CF_PLD_PHYS 0x30000000 /* 16 bit wide */
+#define PCM990_CF_PLD_BASE 0xef000000
+#define PCM990_CF_PLD_SIZE (1*1024*1024)
+#define PCM990_CF_PLD_P2V(x) ((x) - PCM990_CF_PLD_PHYS + PCM990_CF_PLD_BASE)
+#define PCM990_CF_PLD_V2P(x) ((x) - PCM990_CF_PLD_BASE + PCM990_CF_PLD_PHYS)
+
+/* visible CPLD (U6) registers */
+#define PCM990_CF_PLD_REG0 0x1000 /* OFFSET CF REGISTER 0 */
+#define PCM990_CF_REG0_LED 0x0001 /* RW LED on */
+#define PCM990_CF_REG0_BLK 0x0002 /* RW LED flash when access */
+#define PCM990_CF_REG0_PM5V 0x0004 /* R System VCC_5V enable */
+#define PCM990_CF_REG0_STBY 0x0008 /* R System StandBy */
+
+#define PCM990_CF_PLD_REG1 0x1002 /* OFFSET CF REGISTER 1 */
+#define PCM990_CF_REG1_IDEMODE 0x0001 /* RW CF card run as TrueIDE */
+#define PCM990_CF_REG1_CF0 0x0002 /* RW CF card at ADDR 0x28000000 */
+
+#define PCM990_CF_PLD_REG2 0x1004 /* OFFSET CF REGISTER 2 */
+#define PCM990_CF_REG2_RES 0x0002 /* RW CF RESET BIT */
+#define PCM990_CF_REG2_RDYENA 0x0004 /* RW Enable CF_RDY */
+#define PCM990_CF_REG2_RDY 0x0008 /* R CF_RDY auf PWAIT */
+
+#define PCM990_CF_PLD_REG3 0x1006 /* OFFSET CF REGISTER 3 */
+#define PCM990_CF_REG3_CFOE 0x0001 /* RW Latch on Databus */
+#define PCM990_CF_REG3_CFON 0x0002 /* RW Latch on Control Address */
+#define PCM990_CF_REG3_CFIN 0x0004 /* RW Latch on Interrupt usw. */
+#define PCM990_CF_REG3_CFCD 0x0008 /* RW Latch on CD1/2 VS1/2 usw */
+
+#define PCM990_CF_PLD_REG4 0x1008 /* OFFSET CF REGISTER 4 */
+#define PCM990_CF_REG4_PWRENA 0x0001 /* RW CF Power on (CD1/2 = "00") */
+#define PCM990_CF_REG4_5_3V 0x0002 /* RW 1 = 5V CF_VCC 0 = 3 V CF_VCC */
+#define PCM990_CF_REG4_3B 0x0004 /* RW 3.0V Backup from VCC (5_3V=0) */
+#define PCM990_CF_REG4_PWG 0x0008 /* R CF-Power is on */
+
+#define PCM990_CF_PLD_REG5 0x100A /* OFFSET CF REGISTER 5 */
+#define PCM990_CF_REG5_BVD1 0x0001 /* R CF /BVD1 */
+#define PCM990_CF_REG5_BVD2 0x0002 /* R CF /BVD2 */
+#define PCM990_CF_REG5_VS1 0x0004 /* R CF /VS1 */
+#define PCM990_CF_REG5_VS2 0x0008 /* R CF /VS2 */
+
+#define PCM990_CF_PLD_REG6 0x100C /* OFFSET CF REGISTER 6 */
+#define PCM990_CF_REG6_CD1 0x0001 /* R CF Card_Detect1 */
+#define PCM990_CF_REG6_CD2 0x0002 /* R CF Card_Detect2 */
+
+#ifndef __ASSEMBLY__
+# define __PCM990_CF_PLD_REG(x) \
+ (*((volatile unsigned char *)PCM990_CF_PLD_P2V(x)))
+#else
+# define __PCM990_CF_PLD_REG(x) PCM990_CF_PLD_P2V(x)
+#endif
+
+#define PCM990_CF0 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG0)
+#define PCM990_CF1 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG1)
+#define PCM990_CF2 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG2)
+#define PCM990_CF3 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG3)
+#define PCM990_CF4 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG4)
+#define PCM990_CF5 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG5)
+#define PCM990_CF6 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG6)
+
+/*
+ * Wolfson AC97 Touch
+ */
+#define PCM990_AC97_IRQ_GPIO 10
+#define PCM990_AC97_IRQ IRQ_GPIO(PCM990_AC97_IRQ_GPIO)
+#define PCM990_AC97_IRQ_EDGE IRQT_RISING
+
+/*
+ * MMC phyCORE
+ */
+#define PCM990_MMC0_IRQ_GPIO 9
+#define PCM990_MMC0_IRQ IRQ_GPIO(PCM990_MMC0_IRQ_GPIO)
+#define PCM990_MMC0_IRQ_EDGE IRQT_FALLING
+
+/*
+ * USB phyCore
+ */
+#define PCM990_USB_OVERCURRENT (88 | GPIO_ALT_FN_1_IN)
+#define PCM990_USB_PWR_EN (89 | GPIO_ALT_FN_2_OUT)
projects / linux-2.6-omap-h63xx.git / commitdiff