cris_ide_set_speed(TYPE_DMA, 0, strobe, hold);
}
+static void __init cris_setup_ports(hw_regs_t *hw, unsigned long base)
+{
+ int i;
+
+ memset(hw, 0, sizeof(*hw));
+
+ for (i = 0; i <= 7; i++)
+ hw->io_ports[i] = base + cris_ide_reg_addr(i, 0, 1);
+
+ /*
+ * the IDE control register is at ATA address 6,
+ * with CS1 active instead of CS0
+ */
+ hw->io_ports[IDE_CONTROL_OFFSET] = base + cris_ide_reg_addr(6, 1, 0);
+
+ hw->irq = ide_default_irq(0);
+ hw->ack_intr = cris_ide_ack_intr;
+}
+
static const struct ide_port_info cris_port_info __initdata = {
.chipset = ide_etrax100,
.host_flags = IDE_HFLAG_NO_ATAPI_DMA |
static int __init init_e100_ide(void)
{
hw_regs_t hw;
- int ide_offsets[IDE_NR_PORTS], h, i;
+ int h;
u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
printk("ide: ETRAX FS built-in ATA DMA controller\n");
- for (i = IDE_DATA_OFFSET; i <= IDE_STATUS_OFFSET; i++)
- ide_offsets[i] = cris_ide_reg_addr(i, 0, 1);
-
- /* the IDE control register is at ATA address 6, with CS1 active instead of CS0 */
- ide_offsets[IDE_CONTROL_OFFSET] = cris_ide_reg_addr(6, 1, 0);
-
for (h = 0; h < 4; h++) {
ide_hwif_t *hwif = NULL;
- ide_setup_ports(&hw, cris_ide_base_address(h),
- ide_offsets,
- 0, 0, cris_ide_ack_intr,
- ide_default_irq(0));
+ cris_setup_ports(&hw, cris_ide_base_address(h));
+
hwif = ide_find_port(hw.io_ports[IDE_DATA_OFFSET]);
if (hwif == NULL)
continue;
EXPORT_SYMBOL(ide_unregister);
-
-/**
- * ide_setup_ports - set up IDE interface ports
- * @hw: register descriptions
- * @base: base register
- * @offsets: table of register offsets
- * @ctrl: control register
- * @ack_irq: IRQ ack
- * @irq: interrupt lie
- *
- * Setup hw_regs_t structure described by parameters. You
- * may set up the hw structure yourself OR use this routine to
- * do it for you. This is basically a helper
- *
- */
-
-void ide_setup_ports ( hw_regs_t *hw,
- unsigned long base, int *offsets,
- unsigned long ctrl, unsigned long intr,
- ide_ack_intr_t *ack_intr,
-/*
- * ide_io_ops_t *iops,
- */
- int irq)
-{
- int i;
-
- memset(hw, 0, sizeof(hw_regs_t));
- for (i = 0; i < IDE_NR_PORTS; i++) {
- if (offsets[i] == -1) {
- switch(i) {
- case IDE_CONTROL_OFFSET:
- hw->io_ports[i] = ctrl;
- break;
-#if defined(CONFIG_AMIGA) || defined(CONFIG_MAC)
- case IDE_IRQ_OFFSET:
- hw->io_ports[i] = intr;
- break;
-#endif /* (CONFIG_AMIGA) || (CONFIG_MAC) */
- default:
- hw->io_ports[i] = 0;
- break;
- }
- } else {
- hw->io_ports[i] = base + offsets[i];
- }
- }
- hw->irq = irq;
- hw->ack_intr = ack_intr;
-/*
- * hw->iops = iops;
- */
-}
-
void ide_init_port_hw(ide_hwif_t *hwif, hw_regs_t *hw)
{
memcpy(hwif->io_ports, hw->io_ports, sizeof(hwif->io_ports));
XSURF_BASE1, XSURF_BASE2
};
-
/*
* Offsets from one of the above bases
*/
-#define BUDDHA_DATA 0x00
-#define BUDDHA_ERROR 0x06 /* see err-bits */
-#define BUDDHA_NSECTOR 0x0a /* nr of sectors to read/write */
-#define BUDDHA_SECTOR 0x0e /* starting sector */
-#define BUDDHA_LCYL 0x12 /* starting cylinder */
-#define BUDDHA_HCYL 0x16 /* high byte of starting cyl */
-#define BUDDHA_SELECT 0x1a /* 101dhhhh , d=drive, hhhh=head */
-#define BUDDHA_STATUS 0x1e /* see status-bits */
#define BUDDHA_CONTROL 0x11a
-#define XSURF_CONTROL -1 /* X-Surf has no CS1* (Control/AltStat) */
-
-static int buddha_offsets[IDE_NR_PORTS] __initdata = {
- BUDDHA_DATA, BUDDHA_ERROR, BUDDHA_NSECTOR, BUDDHA_SECTOR, BUDDHA_LCYL,
- BUDDHA_HCYL, BUDDHA_SELECT, BUDDHA_STATUS, BUDDHA_CONTROL, -1
-};
-
-static int xsurf_offsets[IDE_NR_PORTS] __initdata = {
- BUDDHA_DATA, BUDDHA_ERROR, BUDDHA_NSECTOR, BUDDHA_SECTOR, BUDDHA_LCYL,
- BUDDHA_HCYL, BUDDHA_SELECT, BUDDHA_STATUS, XSURF_CONTROL, -1
-};
/*
* Other registers
return 1;
}
+static void __init buddha_setup_ports(hw_regs_t *hw, unsigned long base,
+ unsigned long ctl, unsigned long irq_port,
+ ide_ack_intr_t *ack_intr)
+{
+ int i;
+
+ memset(hw, 0, sizeof(*hw));
+
+ hw->io_ports[IDE_DATA_OFFSET] = base;
+
+ for (i = 1; i < 8; i++)
+ hw->io_ports[i] = base + 2 + i * 4;
+
+ hw->io_ports[IDE_CONTROL_OFFSET] = ctl;
+ hw->io_ports[IDE_IRQ_OFFSET] = irq_port;
+
+ hw->irq = IRQ_AMIGA_PORTS;
+ hw->ack_intr = ack_intr;
+}
+
/*
* Probe for a Buddha or Catweasel IDE interface
*/
printk(KERN_INFO "ide: %s IDE controller\n",
buddha_board_name[type]);
- for(i=0;i<buddha_num_hwifs;i++) {
- if(type != BOARD_XSURF) {
- ide_setup_ports(&hw, (buddha_board+buddha_bases[i]),
- buddha_offsets, 0,
- (buddha_board+buddha_irqports[i]),
- buddha_ack_intr,
-// budda_iops,
- IRQ_AMIGA_PORTS);
+ for (i = 0; i < buddha_num_hwifs; i++) {
+ unsigned long base, ctl, irq_port;
+ ide_ack_intr_t *ack_intr;
+
+ if (type != BOARD_XSURF) {
+ base = buddha_board + buddha_bases[i];
+ ctl = base + BUDDHA_CONTROL;
+ irq_port = buddha_board + buddha_irqports[i];
+ ack_intr = buddha_ack_intr;
} else {
- ide_setup_ports(&hw, (buddha_board+xsurf_bases[i]),
- xsurf_offsets, 0,
- (buddha_board+xsurf_irqports[i]),
- xsurf_ack_intr,
-// xsurf_iops,
- IRQ_AMIGA_PORTS);
- }
+ base = buddha_board + xsurf_bases[i];
+ /* X-Surf has no CS1* (Control/AltStat) */
+ ctl = 0;
+ irq_port = buddha_board + xsurf_irqports[i];
+ ack_intr = xsurf_ack_intr;
+ }
+
+ buddha_setup_ports(&hw, base, ctl, irq_port, ack_intr);
hwif = ide_find_port(hw.io_ports[IDE_DATA_OFFSET]);
if (hwif) {
* Offsets from the above base
*/
-#define ATA_HD_DATA 0x00
-#define ATA_HD_ERROR 0x05 /* see err-bits */
-#define ATA_HD_NSECTOR 0x09 /* nr of sectors to read/write */
-#define ATA_HD_SECTOR 0x0d /* starting sector */
-#define ATA_HD_LCYL 0x11 /* starting cylinder */
-#define ATA_HD_HCYL 0x15 /* high byte of starting cyl */
-#define ATA_HD_SELECT 0x19 /* 101dhhhh , d=drive, hhhh=head */
-#define ATA_HD_STATUS 0x1d /* see status-bits */
#define ATA_HD_CONTROL 0x39
-static int falconide_offsets[IDE_NR_PORTS] __initdata = {
- ATA_HD_DATA, ATA_HD_ERROR, ATA_HD_NSECTOR, ATA_HD_SECTOR, ATA_HD_LCYL,
- ATA_HD_HCYL, ATA_HD_SELECT, ATA_HD_STATUS, ATA_HD_CONTROL, -1
-};
-
-
/*
* falconide_intr_lock is used to obtain access to the IDE interrupt,
* which is shared between several drivers.
int falconide_intr_lock;
EXPORT_SYMBOL(falconide_intr_lock);
+static void __init falconide_setup_ports(hw_regs_t *hw)
+{
+ int i;
+
+ memset(hw, 0, sizeof(*hw));
+
+ hw->io_ports[IDE_DATA_OFFSET] = ATA_HD_BASE;
+
+ for (i = 1; i < 8; i++)
+ hw->io_ports[i] = ATA_HD_BASE + 1 + i * 4;
+
+ hw->io_ports[IDE_CONTROL_OFFSET] = ATA_HD_CONTROL;
+
+ hw->irq = IRQ_MFP_IDE;
+ hw->ack_intr = NULL;
+}
/*
* Probe for a Falcon IDE interface
static int __init falconide_init(void)
{
- if (MACH_IS_ATARI && ATARIHW_PRESENT(IDE)) {
hw_regs_t hw;
ide_hwif_t *hwif;
+ if (!MACH_IS_ATARI || !ATARIHW_PRESENT(IDE))
+ return 0;
+
printk(KERN_INFO "ide: Falcon IDE controller\n");
- ide_setup_ports(&hw, ATA_HD_BASE, falconide_offsets,
- 0, 0, NULL,
-// falconide_iops,
- IRQ_MFP_IDE);
+ falconide_setup_ports(&hw);
hwif = ide_find_port(hw.io_ports[IDE_DATA_OFFSET]);
if (hwif) {
ide_device_add(idx, NULL);
}
- }
- return 0;
+ return 0;
}
module_init(falconide_init);
* Offsets from one of the above bases
*/
-#define GAYLE_DATA 0x00
-#define GAYLE_ERROR 0x06 /* see err-bits */
-#define GAYLE_NSECTOR 0x0a /* nr of sectors to read/write */
-#define GAYLE_SECTOR 0x0e /* starting sector */
-#define GAYLE_LCYL 0x12 /* starting cylinder */
-#define GAYLE_HCYL 0x16 /* high byte of starting cyl */
-#define GAYLE_SELECT 0x1a /* 101dhhhh , d=drive, hhhh=head */
-#define GAYLE_STATUS 0x1e /* see status-bits */
#define GAYLE_CONTROL 0x101a
-static int gayle_offsets[IDE_NR_PORTS] __initdata = {
- GAYLE_DATA, GAYLE_ERROR, GAYLE_NSECTOR, GAYLE_SECTOR, GAYLE_LCYL,
- GAYLE_HCYL, GAYLE_SELECT, GAYLE_STATUS, -1, -1
-};
-
-
/*
* These are at different offsets from the base
*/
return 1;
}
+static void __init gayle_setup_ports(hw_regs_t *hw, unsigned long base,
+ unsigned long ctl, unsigned long irq_port,
+ ide_ack_intr_t *ack_intr);
+{
+ int i;
+
+ memset(hw, 0, sizeof(*hw));
+
+ hw->io_ports[IDE_DATA_OFFSET] = base;
+
+ for (i = 1; i < 8; i++)
+ hw->io_ports[i] = base + 2 + i * 4;
+
+ hw->io_ports[IDE_CONTROL_OFFSET] = ctl;
+ hw->io_ports[IDE_IRQ_OFFSET] = irq_port;
+
+ hw->irq = IRQ_AMIGA_PORTS;
+ hw->ack_intr = ack_intr;
+}
+
/*
* Probe for a Gayle IDE interface (and optionally for an IDE doubler)
*/
base = (unsigned long)ZTWO_VADDR(phys_base);
ctrlport = GAYLE_HAS_CONTROL_REG ? (base + GAYLE_CONTROL) : 0;
- ide_setup_ports(&hw, base, gayle_offsets,
- ctrlport, irqport, ack_intr,
-// &gayle_iops,
- IRQ_AMIGA_PORTS);
+ gayle_setup_ports(&hw, base, ctrlport, irqport, ack_intr);
hwif = ide_find_port(base);
if (hwif) {
* These match MkLinux so they should be correct.
*/
-#define IDE_DATA 0x00
-#define IDE_ERROR 0x04 /* see err-bits */
-#define IDE_NSECTOR 0x08 /* nr of sectors to read/write */
-#define IDE_SECTOR 0x0c /* starting sector */
-#define IDE_LCYL 0x10 /* starting cylinder */
-#define IDE_HCYL 0x14 /* high byte of starting cyl */
-#define IDE_SELECT 0x18 /* 101dhhhh , d=drive, hhhh=head */
-#define IDE_STATUS 0x1c /* see status-bits */
#define IDE_CONTROL 0x38 /* control/altstatus */
/*
volatile unsigned char *ide_ifr = (unsigned char *) (IDE_BASE + IDE_IFR);
-static int macide_offsets[IDE_NR_PORTS] = {
- IDE_DATA, IDE_ERROR, IDE_NSECTOR, IDE_SECTOR, IDE_LCYL,
- IDE_HCYL, IDE_SELECT, IDE_STATUS, IDE_CONTROL
-};
-
int macide_ack_intr(ide_hwif_t* hwif)
{
if (*ide_ifr & 0x20) {
return 0;
}
+static void __init macide_setup_ports(hw_regs_t *hw, unsigned long base,
+ int irq, ide_ack_intr_t *ack_intr)
+{
+ int i;
+
+ memset(hw, 0, sizeof(*hw));
+
+ for (i = 0; i < 8; i++)
+ hw->io_ports[i] = base + i * 4;
+
+ hw->io_ports[IDE_CONTROL_OFFSET] = IDE_CONTROL;
+
+ hw->irq = irq;
+ hw->ack_intr = ack_intr;
+}
+
static const char *mac_ide_name[] =
{ "Quadra", "Powerbook", "Powerbook Baboon" };
static int __init macide_init(void)
{
- hw_regs_t hw;
ide_hwif_t *hwif;
+ ide_ack_intr_t *ack_intr;
+ unsigned long base;
+ int irq;
+ hw_regs_t hw;
switch (macintosh_config->ide_type) {
case MAC_IDE_QUADRA:
- ide_setup_ports(&hw, IDE_BASE, macide_offsets,
- 0, 0, macide_ack_intr,
-// quadra_ide_iops,
- IRQ_NUBUS_F);
+ base = IDE_BASE;
+ ack_intr = macide_ack_intr;
+ irq = IRQ_NUBUS_F;
break;
case MAC_IDE_PB:
- ide_setup_ports(&hw, IDE_BASE, macide_offsets,
- 0, 0, macide_ack_intr,
-// macide_pb_iops,
- IRQ_NUBUS_C);
+ base = IDE_BASE;
+ ack_intr = macide_ack_intr;
+ irq = IRQ_NUBUS_C;
break;
case MAC_IDE_BABOON:
- ide_setup_ports(&hw, BABOON_BASE, macide_offsets,
- 0, 0, NULL,
-// macide_baboon_iops,
- IRQ_BABOON_1);
+ base = BABOON_BASE;
+ ack_intr = NULL;
+ irq = IRQ_BABOON_1;
break;
default:
return -ENODEV;
printk(KERN_INFO "ide: Macintosh %s IDE controller\n",
mac_ide_name[macintosh_config->ide_type - 1]);
+ macide_setup_ports(&hw, base, irq, ack_intr);
+
hwif = ide_find_port(hw.io_ports[IDE_DATA_OFFSET]);
if (hwif) {
u8 index = hwif->index;
/*
- * This is very similar to ide_setup_ports except that addresses
- * are pretranslated for q40 ISA access
+ * Addresses are pretranslated for Q40 ISA access.
*/
void q40_ide_setup_ports ( hw_regs_t *hw,
unsigned long base, int *offsets,
unsigned long ctrl, unsigned long intr,
ide_ack_intr_t *ack_intr,
-/*
- * ide_io_ops_t *iops,
- */
int irq)
{
int i;
hw->irq = irq;
hw->ack_intr = ack_intr;
-/*
- * hw->iops = iops;
- */
}
int ide_register_hw(hw_regs_t *, void (*)(struct ide_drive_s *),
struct hwif_s **);
-void ide_setup_ports( hw_regs_t *hw,
- unsigned long base,
- int *offsets,
- unsigned long ctrl,
- unsigned long intr,
- ide_ack_intr_t *ack_intr,
-#if 0
- ide_io_ops_t *iops,
-#endif
- int irq);
-
static inline void ide_std_init_ports(hw_regs_t *hw,
unsigned long io_addr,
unsigned long ctl_addr)
projects / linux-2.6-omap-h63xx.git / commitdiff