--- /dev/null
+/*
+ * linux/arch/arm/mach-pxa/corgi_lcd.c
+ *
+ * Corgi/Spitz LCD Specific Code
+ *
+ * Copyright (C) 2005 Richard Purdie
+ *
+ * Connectivity:
+ * Corgi - LCD to ATI Imageon w100 (Wallaby)
+ * Spitz - LCD to PXA Framebuffer
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/module.h>
+#include <linux/string.h>
+#include <mach/akita.h>
+#include <mach/corgi.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
+#include <mach/sharpsl.h>
+#include <mach/spitz.h>
+#include <asm/hardware/scoop.h>
+#include <asm/mach/sharpsl_param.h>
+#include "generic.h"
+
+/* Register Addresses */
+#define RESCTL_ADRS 0x00
+#define PHACTRL_ADRS 0x01
+#define DUTYCTRL_ADRS 0x02
+#define POWERREG0_ADRS 0x03
+#define POWERREG1_ADRS 0x04
+#define GPOR3_ADRS 0x05
+#define PICTRL_ADRS 0x06
+#define POLCTRL_ADRS 0x07
+
+/* Register Bit Definitions */
+#define RESCTL_QVGA 0x01
+#define RESCTL_VGA 0x00
+
+#define POWER1_VW_ON 0x01 /* VW Supply FET ON */
+#define POWER1_GVSS_ON 0x02 /* GVSS(-8V) Power Supply ON */
+#define POWER1_VDD_ON 0x04 /* VDD(8V),SVSS(-4V) Power Supply ON */
+
+#define POWER1_VW_OFF 0x00 /* VW Supply FET OFF */
+#define POWER1_GVSS_OFF 0x00 /* GVSS(-8V) Power Supply OFF */
+#define POWER1_VDD_OFF 0x00 /* VDD(8V),SVSS(-4V) Power Supply OFF */
+
+#define POWER0_COM_DCLK 0x01 /* COM Voltage DC Bias DAC Serial Data Clock */
+#define POWER0_COM_DOUT 0x02 /* COM Voltage DC Bias DAC Serial Data Out */
+#define POWER0_DAC_ON 0x04 /* DAC Power Supply ON */
+#define POWER0_COM_ON 0x08 /* COM Power Supply ON */
+#define POWER0_VCC5_ON 0x10 /* VCC5 Power Supply ON */
+
+#define POWER0_DAC_OFF 0x00 /* DAC Power Supply OFF */
+#define POWER0_COM_OFF 0x00 /* COM Power Supply OFF */
+#define POWER0_VCC5_OFF 0x00 /* VCC5 Power Supply OFF */
+
+#define PICTRL_INIT_STATE 0x01
+#define PICTRL_INIOFF 0x02
+#define PICTRL_POWER_DOWN 0x04
+#define PICTRL_COM_SIGNAL_OFF 0x08
+#define PICTRL_DAC_SIGNAL_OFF 0x10
+
+#define POLCTRL_SYNC_POL_FALL 0x01
+#define POLCTRL_EN_POL_FALL 0x02
+#define POLCTRL_DATA_POL_FALL 0x04
+#define POLCTRL_SYNC_ACT_H 0x08
+#define POLCTRL_EN_ACT_L 0x10
+
+#define POLCTRL_SYNC_POL_RISE 0x00
+#define POLCTRL_EN_POL_RISE 0x00
+#define POLCTRL_DATA_POL_RISE 0x00
+#define POLCTRL_SYNC_ACT_L 0x00
+#define POLCTRL_EN_ACT_H 0x00
+
+#define PHACTRL_PHASE_MANUAL 0x01
+#define DEFAULT_PHAD_QVGA (9)
+#define DEFAULT_COMADJ (125)
+
+/*
+ * This is only a psuedo I2C interface. We can't use the standard kernel
+ * routines as the interface is write only. We just assume the data is acked...
+ */
+static void lcdtg_ssp_i2c_send(u8 data)
+{
+ corgi_ssp_lcdtg_send(POWERREG0_ADRS, data);
+ udelay(10);
+}
+
+static void lcdtg_i2c_send_bit(u8 data)
+{
+ lcdtg_ssp_i2c_send(data);
+ lcdtg_ssp_i2c_send(data | POWER0_COM_DCLK);
+ lcdtg_ssp_i2c_send(data);
+}
+
+static void lcdtg_i2c_send_start(u8 base)
+{
+ lcdtg_ssp_i2c_send(base | POWER0_COM_DCLK | POWER0_COM_DOUT);
+ lcdtg_ssp_i2c_send(base | POWER0_COM_DCLK);
+ lcdtg_ssp_i2c_send(base);
+}
+
+static void lcdtg_i2c_send_stop(u8 base)
+{
+ lcdtg_ssp_i2c_send(base);
+ lcdtg_ssp_i2c_send(base | POWER0_COM_DCLK);
+ lcdtg_ssp_i2c_send(base | POWER0_COM_DCLK | POWER0_COM_DOUT);
+}
+
+static void lcdtg_i2c_send_byte(u8 base, u8 data)
+{
+ int i;
+ for (i = 0; i < 8; i++) {
+ if (data & 0x80)
+ lcdtg_i2c_send_bit(base | POWER0_COM_DOUT);
+ else
+ lcdtg_i2c_send_bit(base);
+ data <<= 1;
+ }
+}
+
+static void lcdtg_i2c_wait_ack(u8 base)
+{
+ lcdtg_i2c_send_bit(base);
+}
+
+static void lcdtg_set_common_voltage(u8 base_data, u8 data)
+{
+ /* Set Common Voltage to M62332FP via I2C */
+ lcdtg_i2c_send_start(base_data);
+ lcdtg_i2c_send_byte(base_data, 0x9c);
+ lcdtg_i2c_wait_ack(base_data);
+ lcdtg_i2c_send_byte(base_data, 0x00);
+ lcdtg_i2c_wait_ack(base_data);
+ lcdtg_i2c_send_byte(base_data, data);
+ lcdtg_i2c_wait_ack(base_data);
+ lcdtg_i2c_send_stop(base_data);
+}
+
+/* Set Phase Adjust */
+static void lcdtg_set_phadadj(int mode)
+{
+ int adj;
+ switch(mode) {
+ case 480:
+ case 640:
+ /* Setting for VGA */
+ adj = sharpsl_param.phadadj;
+ if (adj < 0) {
+ adj = PHACTRL_PHASE_MANUAL;
+ } else {
+ adj = ((adj & 0x0f) << 1) | PHACTRL_PHASE_MANUAL;
+ }
+ break;
+ case 240:
+ case 320:
+ default:
+ /* Setting for QVGA */
+ adj = (DEFAULT_PHAD_QVGA << 1) | PHACTRL_PHASE_MANUAL;
+ break;
+ }
+
+ corgi_ssp_lcdtg_send(PHACTRL_ADRS, adj);
+}
+
+static int lcd_inited;
+
+void corgi_lcdtg_hw_init(int mode)
+{
+ if (!lcd_inited) {
+ int comadj;
+
+ /* Initialize Internal Logic & Port */
+ corgi_ssp_lcdtg_send(PICTRL_ADRS, PICTRL_POWER_DOWN | PICTRL_INIOFF | PICTRL_INIT_STATE
+ | PICTRL_COM_SIGNAL_OFF | PICTRL_DAC_SIGNAL_OFF);
+
+ corgi_ssp_lcdtg_send(POWERREG0_ADRS, POWER0_COM_DCLK | POWER0_COM_DOUT | POWER0_DAC_OFF
+ | POWER0_COM_OFF | POWER0_VCC5_OFF);
+
+ corgi_ssp_lcdtg_send(POWERREG1_ADRS, POWER1_VW_OFF | POWER1_GVSS_OFF | POWER1_VDD_OFF);
+
+ /* VDD(+8V), SVSS(-4V) ON */
+ corgi_ssp_lcdtg_send(POWERREG1_ADRS, POWER1_VW_OFF | POWER1_GVSS_OFF | POWER1_VDD_ON);
+ mdelay(3);
+
+ /* DAC ON */
+ corgi_ssp_lcdtg_send(POWERREG0_ADRS, POWER0_COM_DCLK | POWER0_COM_DOUT | POWER0_DAC_ON
+ | POWER0_COM_OFF | POWER0_VCC5_OFF);
+
+ /* INIB = H, INI = L */
+ /* PICTL[0] = H , PICTL[1] = PICTL[2] = PICTL[4] = L */
+ corgi_ssp_lcdtg_send(PICTRL_ADRS, PICTRL_INIT_STATE | PICTRL_COM_SIGNAL_OFF);
+
+ /* Set Common Voltage */
+ comadj = sharpsl_param.comadj;
+ if (comadj < 0)
+ comadj = DEFAULT_COMADJ;
+ lcdtg_set_common_voltage((POWER0_DAC_ON | POWER0_COM_OFF | POWER0_VCC5_OFF), comadj);
+
+ /* VCC5 ON, DAC ON */
+ corgi_ssp_lcdtg_send(POWERREG0_ADRS, POWER0_COM_DCLK | POWER0_COM_DOUT | POWER0_DAC_ON |
+ POWER0_COM_OFF | POWER0_VCC5_ON);
+
+ /* GVSS(-8V) ON, VDD ON */
+ corgi_ssp_lcdtg_send(POWERREG1_ADRS, POWER1_VW_OFF | POWER1_GVSS_ON | POWER1_VDD_ON);
+ mdelay(2);
+
+ /* COM SIGNAL ON (PICTL[3] = L) */
+ corgi_ssp_lcdtg_send(PICTRL_ADRS, PICTRL_INIT_STATE);
+
+ /* COM ON, DAC ON, VCC5_ON */
+ corgi_ssp_lcdtg_send(POWERREG0_ADRS, POWER0_COM_DCLK | POWER0_COM_DOUT | POWER0_DAC_ON
+ | POWER0_COM_ON | POWER0_VCC5_ON);
+
+ /* VW ON, GVSS ON, VDD ON */
+ corgi_ssp_lcdtg_send(POWERREG1_ADRS, POWER1_VW_ON | POWER1_GVSS_ON | POWER1_VDD_ON);
+
+ /* Signals output enable */
+ corgi_ssp_lcdtg_send(PICTRL_ADRS, 0);
+
+ /* Set Phase Adjust */
+ lcdtg_set_phadadj(mode);
+
+ /* Initialize for Input Signals from ATI */
+ corgi_ssp_lcdtg_send(POLCTRL_ADRS, POLCTRL_SYNC_POL_RISE | POLCTRL_EN_POL_RISE
+ | POLCTRL_DATA_POL_RISE | POLCTRL_SYNC_ACT_L | POLCTRL_EN_ACT_H);
+ udelay(1000);
+
+ lcd_inited=1;
+ } else {
+ lcdtg_set_phadadj(mode);
+ }
+
+ switch(mode) {
+ case 480:
+ case 640:
+ /* Set Lcd Resolution (VGA) */
+ corgi_ssp_lcdtg_send(RESCTL_ADRS, RESCTL_VGA);
+ break;
+ case 240:
+ case 320:
+ default:
+ /* Set Lcd Resolution (QVGA) */
+ corgi_ssp_lcdtg_send(RESCTL_ADRS, RESCTL_QVGA);
+ break;
+ }
+}
+
+void corgi_lcdtg_suspend(void)
+{
+ /* 60Hz x 2 frame = 16.7msec x 2 = 33.4 msec */
+ mdelay(34);
+
+ /* (1)VW OFF */
+ corgi_ssp_lcdtg_send(POWERREG1_ADRS, POWER1_VW_OFF | POWER1_GVSS_ON | POWER1_VDD_ON);
+
+ /* (2)COM OFF */
+ corgi_ssp_lcdtg_send(PICTRL_ADRS, PICTRL_COM_SIGNAL_OFF);
+ corgi_ssp_lcdtg_send(POWERREG0_ADRS, POWER0_DAC_ON | POWER0_COM_OFF | POWER0_VCC5_ON);
+
+ /* (3)Set Common Voltage Bias 0V */
+ lcdtg_set_common_voltage(POWER0_DAC_ON | POWER0_COM_OFF | POWER0_VCC5_ON, 0);
+
+ /* (4)GVSS OFF */
+ corgi_ssp_lcdtg_send(POWERREG1_ADRS, POWER1_VW_OFF | POWER1_GVSS_OFF | POWER1_VDD_ON);
+
+ /* (5)VCC5 OFF */
+ corgi_ssp_lcdtg_send(POWERREG0_ADRS, POWER0_DAC_ON | POWER0_COM_OFF | POWER0_VCC5_OFF);
+
+ /* (6)Set PDWN, INIOFF, DACOFF */
+ corgi_ssp_lcdtg_send(PICTRL_ADRS, PICTRL_INIOFF | PICTRL_DAC_SIGNAL_OFF |
+ PICTRL_POWER_DOWN | PICTRL_COM_SIGNAL_OFF);
+
+ /* (7)DAC OFF */
+ corgi_ssp_lcdtg_send(POWERREG0_ADRS, POWER0_DAC_OFF | POWER0_COM_OFF | POWER0_VCC5_OFF);
+
+ /* (8)VDD OFF */
+ corgi_ssp_lcdtg_send(POWERREG1_ADRS, POWER1_VW_OFF | POWER1_GVSS_OFF | POWER1_VDD_OFF);
+
+ lcd_inited = 0;
+}
+
--- /dev/null
+/*
+ * SSP control code for Sharp Corgi devices
+ *
+ * Copyright (c) 2004-2005 Richard Purdie
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <mach/hardware.h>
+#include <asm/mach-types.h>
+
+#include <mach/ssp.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/regs-ssp.h>
+#include "sharpsl.h"
+
+static DEFINE_SPINLOCK(corgi_ssp_lock);
+static struct ssp_dev corgi_ssp_dev;
+static struct ssp_state corgi_ssp_state;
+static struct corgissp_machinfo *ssp_machinfo;
+
+/*
+ * There are three devices connected to the SSP interface:
+ * 1. A touchscreen controller (TI ADS7846 compatible)
+ * 2. An LCD controller (with some Backlight functionality)
+ * 3. A battery monitoring IC (Maxim MAX1111)
+ *
+ * Each device uses a different speed/mode of communication.
+ *
+ * The touchscreen is very sensitive and the most frequently used
+ * so the port is left configured for this.
+ *
+ * Devices are selected using Chip Selects on GPIOs.
+ */
+
+/*
+ * ADS7846 Routines
+ */
+unsigned long corgi_ssp_ads7846_putget(ulong data)
+{
+ unsigned long flag;
+ u32 ret = 0;
+
+ spin_lock_irqsave(&corgi_ssp_lock, flag);
+ if (ssp_machinfo->cs_ads7846 >= 0)
+ GPCR(ssp_machinfo->cs_ads7846) = GPIO_bit(ssp_machinfo->cs_ads7846);
+
+ ssp_write_word(&corgi_ssp_dev,data);
+ ssp_read_word(&corgi_ssp_dev, &ret);
+
+ if (ssp_machinfo->cs_ads7846 >= 0)
+ GPSR(ssp_machinfo->cs_ads7846) = GPIO_bit(ssp_machinfo->cs_ads7846);
+ spin_unlock_irqrestore(&corgi_ssp_lock, flag);
+
+ return ret;
+}
+
+/*
+ * NOTE: These functions should always be called in interrupt context
+ * and use the _lock and _unlock functions. They are very time sensitive.
+ */
+void corgi_ssp_ads7846_lock(void)
+{
+ spin_lock(&corgi_ssp_lock);
+ if (ssp_machinfo->cs_ads7846 >= 0)
+ GPCR(ssp_machinfo->cs_ads7846) = GPIO_bit(ssp_machinfo->cs_ads7846);
+}
+
+void corgi_ssp_ads7846_unlock(void)
+{
+ if (ssp_machinfo->cs_ads7846 >= 0)
+ GPSR(ssp_machinfo->cs_ads7846) = GPIO_bit(ssp_machinfo->cs_ads7846);
+ spin_unlock(&corgi_ssp_lock);
+}
+
+void corgi_ssp_ads7846_put(ulong data)
+{
+ ssp_write_word(&corgi_ssp_dev,data);
+}
+
+unsigned long corgi_ssp_ads7846_get(void)
+{
+ u32 ret = 0;
+ ssp_read_word(&corgi_ssp_dev, &ret);
+ return ret;
+}
+
+EXPORT_SYMBOL(corgi_ssp_ads7846_putget);
+EXPORT_SYMBOL(corgi_ssp_ads7846_lock);
+EXPORT_SYMBOL(corgi_ssp_ads7846_unlock);
+EXPORT_SYMBOL(corgi_ssp_ads7846_put);
+EXPORT_SYMBOL(corgi_ssp_ads7846_get);
+
+
+/*
+ * LCD/Backlight Routines
+ */
+unsigned long corgi_ssp_dac_put(ulong data)
+{
+ unsigned long flag, sscr1 = SSCR1_SPH;
+ u32 tmp;
+
+ spin_lock_irqsave(&corgi_ssp_lock, flag);
+
+ if (machine_is_spitz() || machine_is_akita() || machine_is_borzoi())
+ sscr1 = 0;
+
+ ssp_disable(&corgi_ssp_dev);
+ ssp_config(&corgi_ssp_dev, (SSCR0_Motorola | (SSCR0_DSS & 0x07 )), sscr1, 0, SSCR0_SerClkDiv(ssp_machinfo->clk_lcdcon));
+ ssp_enable(&corgi_ssp_dev);
+
+ if (ssp_machinfo->cs_lcdcon >= 0)
+ GPCR(ssp_machinfo->cs_lcdcon) = GPIO_bit(ssp_machinfo->cs_lcdcon);
+ ssp_write_word(&corgi_ssp_dev,data);
+ /* Read null data back from device to prevent SSP overflow */
+ ssp_read_word(&corgi_ssp_dev, &tmp);
+ if (ssp_machinfo->cs_lcdcon >= 0)
+ GPSR(ssp_machinfo->cs_lcdcon) = GPIO_bit(ssp_machinfo->cs_lcdcon);
+
+ ssp_disable(&corgi_ssp_dev);
+ ssp_config(&corgi_ssp_dev, (SSCR0_National | (SSCR0_DSS & 0x0b )), 0, 0, SSCR0_SerClkDiv(ssp_machinfo->clk_ads7846));
+ ssp_enable(&corgi_ssp_dev);
+
+ spin_unlock_irqrestore(&corgi_ssp_lock, flag);
+
+ return 0;
+}
+
+void corgi_ssp_lcdtg_send(u8 adrs, u8 data)
+{
+ corgi_ssp_dac_put(((adrs & 0x07) << 5) | (data & 0x1f));
+}
+
+void corgi_ssp_blduty_set(int duty)
+{
+ corgi_ssp_lcdtg_send(0x02,duty);
+}
+
+EXPORT_SYMBOL(corgi_ssp_lcdtg_send);
+EXPORT_SYMBOL(corgi_ssp_blduty_set);
+
+/*
+ * Max1111 Routines
+ */
+int corgi_ssp_max1111_get(ulong data)
+{
+ unsigned long flag;
+ long voltage = 0, voltage1 = 0, voltage2 = 0;
+
+ spin_lock_irqsave(&corgi_ssp_lock, flag);
+ if (ssp_machinfo->cs_max1111 >= 0)
+ GPCR(ssp_machinfo->cs_max1111) = GPIO_bit(ssp_machinfo->cs_max1111);
+ ssp_disable(&corgi_ssp_dev);
+ ssp_config(&corgi_ssp_dev, (SSCR0_Motorola | (SSCR0_DSS & 0x07 )), 0, 0, SSCR0_SerClkDiv(ssp_machinfo->clk_max1111));
+ ssp_enable(&corgi_ssp_dev);
+
+ udelay(1);
+
+ /* TB1/RB1 */
+ ssp_write_word(&corgi_ssp_dev,data);
+ ssp_read_word(&corgi_ssp_dev, (u32*)&voltage1); /* null read */
+
+ /* TB12/RB2 */
+ ssp_write_word(&corgi_ssp_dev,0);
+ ssp_read_word(&corgi_ssp_dev, (u32*)&voltage1);
+
+ /* TB13/RB3*/
+ ssp_write_word(&corgi_ssp_dev,0);
+ ssp_read_word(&corgi_ssp_dev, (u32*)&voltage2);
+
+ ssp_disable(&corgi_ssp_dev);
+ ssp_config(&corgi_ssp_dev, (SSCR0_National | (SSCR0_DSS & 0x0b )), 0, 0, SSCR0_SerClkDiv(ssp_machinfo->clk_ads7846));
+ ssp_enable(&corgi_ssp_dev);
+ if (ssp_machinfo->cs_max1111 >= 0)
+ GPSR(ssp_machinfo->cs_max1111) = GPIO_bit(ssp_machinfo->cs_max1111);
+ spin_unlock_irqrestore(&corgi_ssp_lock, flag);
+
+ if (voltage1 & 0xc0 || voltage2 & 0x3f)
+ voltage = -1;
+ else
+ voltage = ((voltage1 << 2) & 0xfc) | ((voltage2 >> 6) & 0x03);
+
+ return voltage;
+}
+
+EXPORT_SYMBOL(corgi_ssp_max1111_get);
+
+/*
+ * Support Routines
+ */
+
+void __init corgi_ssp_set_machinfo(struct corgissp_machinfo *machinfo)
+{
+ ssp_machinfo = machinfo;
+}
+
+static int __init corgi_ssp_probe(struct platform_device *dev)
+{
+ int ret;
+
+ /* Chip Select - Disable All */
+ if (ssp_machinfo->cs_lcdcon >= 0)
+ pxa_gpio_mode(ssp_machinfo->cs_lcdcon | GPIO_OUT | GPIO_DFLT_HIGH);
+ if (ssp_machinfo->cs_max1111 >= 0)
+ pxa_gpio_mode(ssp_machinfo->cs_max1111 | GPIO_OUT | GPIO_DFLT_HIGH);
+ if (ssp_machinfo->cs_ads7846 >= 0)
+ pxa_gpio_mode(ssp_machinfo->cs_ads7846 | GPIO_OUT | GPIO_DFLT_HIGH);
+
+ ret = ssp_init(&corgi_ssp_dev, ssp_machinfo->port, 0);
+
+ if (ret)
+ printk(KERN_ERR "Unable to register SSP handler!\n");
+ else {
+ ssp_disable(&corgi_ssp_dev);
+ ssp_config(&corgi_ssp_dev, (SSCR0_National | (SSCR0_DSS & 0x0b )), 0, 0, SSCR0_SerClkDiv(ssp_machinfo->clk_ads7846));
+ ssp_enable(&corgi_ssp_dev);
+ }
+
+ return ret;
+}
+
+static int corgi_ssp_remove(struct platform_device *dev)
+{
+ ssp_exit(&corgi_ssp_dev);
+ return 0;
+}
+
+static int corgi_ssp_suspend(struct platform_device *dev, pm_message_t state)
+{
+ ssp_flush(&corgi_ssp_dev);
+ ssp_save_state(&corgi_ssp_dev,&corgi_ssp_state);
+
+ return 0;
+}
+
+static int corgi_ssp_resume(struct platform_device *dev)
+{
+ if (ssp_machinfo->cs_lcdcon >= 0)
+ GPSR(ssp_machinfo->cs_lcdcon) = GPIO_bit(ssp_machinfo->cs_lcdcon); /* High - Disable LCD Control/Timing Gen */
+ if (ssp_machinfo->cs_max1111 >= 0)
+ GPSR(ssp_machinfo->cs_max1111) = GPIO_bit(ssp_machinfo->cs_max1111); /* High - Disable MAX1111*/
+ if (ssp_machinfo->cs_ads7846 >= 0)
+ GPSR(ssp_machinfo->cs_ads7846) = GPIO_bit(ssp_machinfo->cs_ads7846); /* High - Disable ADS7846*/
+ ssp_restore_state(&corgi_ssp_dev,&corgi_ssp_state);
+ ssp_enable(&corgi_ssp_dev);
+
+ return 0;
+}
+
+static struct platform_driver corgissp_driver = {
+ .probe = corgi_ssp_probe,
+ .remove = corgi_ssp_remove,
+ .suspend = corgi_ssp_suspend,
+ .resume = corgi_ssp_resume,
+ .driver = {
+ .name = "corgi-ssp",
+ },
+};
+
+int __init corgi_ssp_init(void)
+{
+ return platform_driver_register(&corgissp_driver);
+}
+
+arch_initcall(corgi_ssp_init);
* Shared data structures
*/
extern struct platform_device corgiscoop_device;
+extern struct platform_device corgissp_device;
#endif /* __ASM_ARCH_CORGI_H */
*/
extern struct platform_device spitzscoop_device;
extern struct platform_device spitzscoop2_device;
+extern struct platform_device spitzssp_device;
extern struct sharpsl_charger_machinfo spitz_pm_machinfo;
{ 0, 0},
};
+/* MAX1111 Commands */
+#define MAXCTRL_PD0 1u << 0
+#define MAXCTRL_PD1 1u << 1
+#define MAXCTRL_SGL 1u << 2
+#define MAXCTRL_UNI 1u << 3
+#define MAXCTRL_SEL_SH 4
+#define MAXCTRL_STR 1u << 7
+
/*
* Read MAX1111 ADC
*/
-extern int max1111_read_channel(int);
-
int sharpsl_pm_pxa_read_max1111(int channel)
{
if (machine_is_tosa()) // Ugly, better move this function into another module
return 0;
+#ifdef CONFIG_SENSORS_MAX1111
+ extern int max1111_read_channel(int);
+
/* max1111 accepts channels from 0-3, however,
* it is encoded from 0-7 here in the code.
*/
return max1111_read_channel(channel >> 1);
+#else
+ return corgi_ssp_max1111_get((channel << MAXCTRL_SEL_SH) | MAXCTRL_PD0 | MAXCTRL_PD1
+ | MAXCTRL_SGL | MAXCTRL_UNI | MAXCTRL_STR);
+#endif
}
void sharpsl_pm_pxa_init(void)
projects / linux-2.6-omap-h63xx.git / commitdiff