smsc911x: add dynamic bus configuration

Convert the driver to select 16-bit or 32-bit bus access at runtime,
at a small performance cost.

Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/drivers/net/smsc911x.c b/drivers/net/smsc911x.c
index fe517880fc970baad53ac6ccde0c73eb53486f91..4b8ff843e30060a88532c590d9b3e34bc1b91095 100644 (file)
--- a/drivers/net/smsc911x.c
+++ b/drivers/net/smsc911x.c
@@ -77,19 +77,16 @@ struct smsc911x_data {
        unsigned int generation;
 
        /* device configuration (copied from platform_data during probe) */
-       unsigned int irq_polarity;
-       unsigned int irq_type;
-       phy_interface_t phy_interface;
+       struct smsc911x_platform_config config;
 
        /* This needs to be acquired before calling any of below:
         * smsc911x_mac_read(), smsc911x_mac_write()
         */
        spinlock_t mac_lock;
 
-#if (!SMSC_CAN_USE_32BIT)
-       /* spinlock to ensure 16-bit accesses are serialised */
+       /* spinlock to ensure 16-bit accesses are serialised.
+        * unused with a 32-bit bus */
        spinlock_t dev_lock;
-#endif
 
        struct phy_device *phy_dev;
        struct mii_bus *mii_bus;
@@ -121,70 +118,56 @@ struct smsc911x_data {
        unsigned int hashlo;
 };
 
-#if SMSC_CAN_USE_32BIT
-
-static inline u32 smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg)
-{
-       return readl(pdata->ioaddr + reg);
-}
-
-static inline void smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg,
-                                     u32 val)
-{
-       writel(val, pdata->ioaddr + reg);
-}
-
-/* Writes a packet to the TX_DATA_FIFO */
-static inline void
-smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf,
-                     unsigned int wordcount)
-{
-       writesl(pdata->ioaddr + TX_DATA_FIFO, buf, wordcount);
-}
-
-/* Reads a packet out of the RX_DATA_FIFO */
-static inline void
-smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf,
-                    unsigned int wordcount)
-{
-       readsl(pdata->ioaddr + RX_DATA_FIFO, buf, wordcount);
-}
-
-#else                          /* SMSC_CAN_USE_32BIT */
-
-/* These 16-bit access functions are significantly slower, due to the locking
+/* The 16-bit access functions are significantly slower, due to the locking
  * necessary.  If your bus hardware can be configured to do this for you
  * (in response to a single 32-bit operation from software), you should use
  * the 32-bit access functions instead. */
 
 static inline u32 smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg)
 {
-       unsigned long flags;
-       u32 data;
-
-       /* these two 16-bit reads must be performed consecutively, so must
-        * not be interrupted by our own ISR (which would start another
-        * read operation) */
-       spin_lock_irqsave(&pdata->dev_lock, flags);
-       data = ((readw(pdata->ioaddr + reg) & 0xFFFF) |
-               ((readw(pdata->ioaddr + reg + 2) & 0xFFFF) << 16));
-       spin_unlock_irqrestore(&pdata->dev_lock, flags);
+       if (pdata->config.flags & SMSC911X_USE_32BIT)
+               return readl(pdata->ioaddr + reg);
+
+       if (pdata->config.flags & SMSC911X_USE_16BIT) {
+               u32 data;
+               unsigned long flags;
+
+               /* these two 16-bit reads must be performed consecutively, so
+                * must not be interrupted by our own ISR (which would start
+                * another read operation) */
+               spin_lock_irqsave(&pdata->dev_lock, flags);
+               data = ((readw(pdata->ioaddr + reg) & 0xFFFF) |
+                       ((readw(pdata->ioaddr + reg + 2) & 0xFFFF) << 16));
+               spin_unlock_irqrestore(&pdata->dev_lock, flags);
+
+               return data;
+       }
 
-       return data;
+       BUG();
 }
 
 static inline void smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg,
                                      u32 val)
 {
-       unsigned long flags;
+       if (pdata->config.flags & SMSC911X_USE_32BIT) {
+               writel(val, pdata->ioaddr + reg);
+               return;
+       }
+
+       if (pdata->config.flags & SMSC911X_USE_16BIT) {
+               unsigned long flags;
+
+               /* these two 16-bit writes must be performed consecutively, so
+                * must not be interrupted by our own ISR (which would start
+                * another read operation) */
+               spin_lock_irqsave(&pdata->dev_lock, flags);
+               writew(val & 0xFFFF, pdata->ioaddr + reg);
+               writew((val >> 16) & 0xFFFF, pdata->ioaddr + reg + 2);
+               spin_unlock_irqrestore(&pdata->dev_lock, flags);
+               return;
+       }
 
-       /* these two 16-bit writes must be performed consecutively, so must
-        * not be interrupted by our own ISR (which would start another
-        * read operation) */
-       spin_lock_irqsave(&pdata->dev_lock, flags);
-       writew(val & 0xFFFF, pdata->ioaddr + reg);
-       writew((val >> 16) & 0xFFFF, pdata->ioaddr + reg + 2);
-       spin_unlock_irqrestore(&pdata->dev_lock, flags);
+       BUG();
 }
 
 /* Writes a packet to the TX_DATA_FIFO */
@@ -192,8 +175,18 @@ static inline void
 smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf,
                      unsigned int wordcount)
 {
-       while (wordcount--)
-               smsc911x_reg_write(pdata, TX_DATA_FIFO, *buf++);
+       if (pdata->config.flags & SMSC911X_USE_32BIT) {
+               writesl(pdata->ioaddr + TX_DATA_FIFO, buf, wordcount);
+               return;
+       }
+
+       if (pdata->config.flags & SMSC911X_USE_16BIT) {
+               while (wordcount--)
+                       smsc911x_reg_write(pdata, TX_DATA_FIFO, *buf++);
+               return;
+       }
+
+       BUG();
 }
 
 /* Reads a packet out of the RX_DATA_FIFO */
@@ -201,11 +194,19 @@ static inline void
 smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf,
                     unsigned int wordcount)
 {
-       while (wordcount--)
-               *buf++ = smsc911x_reg_read(pdata, RX_DATA_FIFO);
-}
+       if (pdata->config.flags & SMSC911X_USE_32BIT) {
+               readsl(pdata->ioaddr + RX_DATA_FIFO, buf, wordcount);
+               return;
+       }
 
-#endif                         /* SMSC_CAN_USE_32BIT */
+       if (pdata->config.flags & SMSC911X_USE_16BIT) {
+               while (wordcount--)
+                       *buf++ = smsc911x_reg_read(pdata, RX_DATA_FIFO);
+               return;
+       }
+
+       BUG();
+}
 
 /* waits for MAC not busy, with timeout.  Only called by smsc911x_mac_read
  * and smsc911x_mac_write, so assumes mac_lock is held */
@@ -790,7 +791,7 @@ static int smsc911x_mii_probe(struct net_device *dev)
        }
 
        phydev = phy_connect(dev, phydev->dev.bus_id,
-               &smsc911x_phy_adjust_link, 0, pdata->phy_interface);
+               &smsc911x_phy_adjust_link, 0, pdata->config.phy_interface);
 
        if (IS_ERR(phydev)) {
                pr_err("%s: Could not attach to PHY\n", dev->name);
@@ -1205,14 +1206,14 @@ static int smsc911x_open(struct net_device *dev)
        /* Set interrupt deassertion to 100uS */
        intcfg = ((10 << 24) | INT_CFG_IRQ_EN_);
 
-       if (pdata->irq_polarity) {
+       if (pdata->config.irq_polarity) {
                SMSC_TRACE(IFUP, "irq polarity: active high");
                intcfg |= INT_CFG_IRQ_POL_;
        } else {
                SMSC_TRACE(IFUP, "irq polarity: active low");
        }
 
-       if (pdata->irq_type) {
+       if (pdata->config.irq_type) {
                SMSC_TRACE(IFUP, "irq type: push-pull");
                intcfg |= INT_CFG_IRQ_TYPE_;
        } else {
@@ -1767,9 +1768,7 @@ static int __devinit smsc911x_init(struct net_device *dev)
        SMSC_TRACE(PROBE, "IRQ: %d", dev->irq);
        SMSC_TRACE(PROBE, "PHY will be autodetected.");
 
-#if (!SMSC_CAN_USE_32BIT)
        spin_lock_init(&pdata->dev_lock);
-#endif
 
        if (pdata->ioaddr == 0) {
                SMSC_WARNING(PROBE, "pdata->ioaddr: 0x00000000");
@@ -1910,6 +1909,7 @@ static int __devinit smsc911x_drv_probe(struct platform_device *pdev)
 {
        struct net_device *dev;
        struct smsc911x_data *pdata;
+       struct smsc911x_platform_config *config = pdev->dev.platform_data;
        struct resource *res;
        unsigned int intcfg = 0;
        int res_size;
@@ -1918,6 +1918,13 @@ static int __devinit smsc911x_drv_probe(struct platform_device *pdev)
 
        pr_info("%s: Driver version %s.\n", SMSC_CHIPNAME, SMSC_DRV_VERSION);
 
+       /* platform data specifies irq & dynamic bus configuration */
+       if (!pdev->dev.platform_data) {
+               pr_warning("%s: platform_data not provided\n", SMSC_CHIPNAME);
+               retval = -ENODEV;
+               goto out_0;
+       }
+
        res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
                                           "smsc911x-memory");
        if (!res)
@@ -1949,15 +1956,8 @@ static int __devinit smsc911x_drv_probe(struct platform_device *pdev)
        dev->irq = platform_get_irq(pdev, 0);
        pdata->ioaddr = ioremap_nocache(res->start, res_size);
 
-       /* copy config parameters across if present, otherwise pdata
-        * defaults to zeros */
-       if (pdev->dev.platform_data) {
-               struct smsc911x_platform_config *config =
-                       pdev->dev.platform_data;
-               pdata->irq_polarity = config->irq_polarity;
-               pdata->irq_type  = config->irq_type;
-               pdata->phy_interface = config->phy_interface;
-       }
+       /* copy config parameters across to pdata */
+       memcpy(&pdata->config, config, sizeof(pdata->config));
 
        pdata->dev = dev;
        pdata->msg_enable = ((1 << debug) - 1);
@@ -1974,10 +1974,10 @@ static int __devinit smsc911x_drv_probe(struct platform_device *pdev)
                goto out_unmap_io_3;
 
        /* configure irq polarity and type before connecting isr */
-       if (pdata->irq_polarity == SMSC911X_IRQ_POLARITY_ACTIVE_HIGH)
+       if (pdata->config.irq_polarity == SMSC911X_IRQ_POLARITY_ACTIVE_HIGH)
                intcfg |= INT_CFG_IRQ_POL_;
 
-       if (pdata->irq_type == SMSC911X_IRQ_TYPE_PUSH_PULL)
+       if (pdata->config.irq_type == SMSC911X_IRQ_TYPE_PUSH_PULL)
                intcfg |= INT_CFG_IRQ_TYPE_;
 
        smsc911x_reg_write(pdata, INT_CFG, intcfg);

diff --git a/drivers/net/smsc911x.h b/drivers/net/smsc911x.h
index feb36de274caa8b4e39d30aadb11b954ad01d891..f818cf0415f7ddea0e86d10546c906335909e81b 100644 (file)
--- a/drivers/net/smsc911x.h
+++ b/drivers/net/smsc911x.h
@@ -21,7 +21,6 @@
 #ifndef __SMSC911X_H__
 #define __SMSC911X_H__
 
-#define SMSC_CAN_USE_32BIT     1
 #define TX_FIFO_LOW_THRESHOLD  ((u32)1600)
 #define SMSC911X_EEPROM_SIZE   ((u32)7)
 #define USE_DEBUG              0

diff --git a/include/linux/smsc911x.h b/include/linux/smsc911x.h
index 47c4ffd10dbb1dc8462eb813cff6e8f34da24c53..1cbf0313adde93f0971e56a89a7a907a08fcb8d6 100644 (file)
--- a/include/linux/smsc911x.h
+++ b/include/linux/smsc911x.h
@@ -28,6 +28,7 @@
 struct smsc911x_platform_config {
        unsigned int irq_polarity;
        unsigned int irq_type;
+       unsigned int flags;
        phy_interface_t phy_interface;
 };
 
@@ -39,4 +40,8 @@ struct smsc911x_platform_config {
 #define SMSC911X_IRQ_TYPE_OPEN_DRAIN           0
 #define SMSC911X_IRQ_TYPE_PUSH_PULL            1
 
+/* Constants for flags */
+#define SMSC911X_USE_16BIT                     (BIT(0))
+#define SMSC911X_USE_32BIT                     (BIT(1))
+
 #endif /* __LINUX_SMSC911X_H__ */