The Ocelot-3 is based off Discovery III System Controller and
PMC-Sierra Rm79000 core.
-config MOMENCO_OCELOT_C
- bool "Momentum Ocelot-C board"
- select DMA_NONCOHERENT
- select HW_HAS_PCI
- select IRQ_CPU
- select IRQ_MV64340
- select PCI_MARVELL
- select RM7000_CPU_SCACHE
- select SWAP_IO_SPACE
- select SYS_HAS_CPU_RM7000
- select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_64BIT_KERNEL
- select SYS_SUPPORTS_BIG_ENDIAN
- select GENERIC_HARDIRQS_NO__DO_IRQ
- help
- The Ocelot is a MIPS-based Single Board Computer (SBC) made by
- Momentum Computer <http://www.momenco.com/>.
-
config PNX8550_JBS
bool "Philips PNX8550 based JBS board"
select PNX8550
cflags-$(CONFIG_MOMENCO_OCELOT) += -Iinclude/asm-mips/mach-ocelot
load-$(CONFIG_MOMENCO_OCELOT) += 0xffffffff80100000
-#
-# Momentum Ocelot-C and -CS boards
-#
-# The Ocelot-C[S] setup.o must be linked early - it does the ioremap() for the
-# mips_io_port_base.
-core-$(CONFIG_MOMENCO_OCELOT_C) += arch/mips/momentum/ocelot_c/
-load-$(CONFIG_MOMENCO_OCELOT_C) += 0xffffffff80100000
-
#
# PMC-Sierra Yosemite
#
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_DDB5477 is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
CONFIG_MOMENCO_OCELOT_3=y
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
+++ /dev/null
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.20
-# Tue Feb 20 21:47:36 2007
-#
-CONFIG_MIPS=y
-
-#
-# Machine selection
-#
-CONFIG_ZONE_DMA=y
-# CONFIG_MIPS_MTX1 is not set
-# CONFIG_MIPS_BOSPORUS is not set
-# CONFIG_MIPS_PB1000 is not set
-# CONFIG_MIPS_PB1100 is not set
-# CONFIG_MIPS_PB1500 is not set
-# CONFIG_MIPS_PB1550 is not set
-# CONFIG_MIPS_PB1200 is not set
-# CONFIG_MIPS_DB1000 is not set
-# CONFIG_MIPS_DB1100 is not set
-# CONFIG_MIPS_DB1500 is not set
-# CONFIG_MIPS_DB1550 is not set
-# CONFIG_MIPS_DB1200 is not set
-# CONFIG_MIPS_MIRAGE is not set
-# CONFIG_BASLER_EXCITE is not set
-# CONFIG_MIPS_COBALT is not set
-# CONFIG_MACH_DECSTATION is not set
-# CONFIG_MACH_JAZZ is not set
-# CONFIG_LASAT is not set
-# CONFIG_MIPS_ATLAS is not set
-# CONFIG_MIPS_MALTA is not set
-# CONFIG_MIPS_SEAD is not set
-# CONFIG_WR_PPMC is not set
-# CONFIG_MIPS_SIM is not set
-# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_3 is not set
-CONFIG_MOMENCO_OCELOT_C=y
-# CONFIG_MOMENCO_OCELOT_G is not set
-# CONFIG_MIPS_XXS1500 is not set
-# CONFIG_PNX8550_JBS is not set
-# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
-# CONFIG_MACH_VR41XX is not set
-# CONFIG_PMC_YOSEMITE is not set
-# CONFIG_QEMU is not set
-# CONFIG_MARKEINS is not set
-# CONFIG_SGI_IP22 is not set
-# CONFIG_SGI_IP27 is not set
-# CONFIG_SGI_IP32 is not set
-# CONFIG_SIBYTE_BIGSUR is not set
-# CONFIG_SIBYTE_SWARM is not set
-# CONFIG_SIBYTE_SENTOSA is not set
-# CONFIG_SIBYTE_RHONE is not set
-# CONFIG_SIBYTE_CARMEL is not set
-# CONFIG_SIBYTE_PTSWARM is not set
-# CONFIG_SIBYTE_LITTLESUR is not set
-# CONFIG_SIBYTE_CRHINE is not set
-# CONFIG_SIBYTE_CRHONE is not set
-# CONFIG_SNI_RM is not set
-# CONFIG_TOSHIBA_JMR3927 is not set
-# CONFIG_TOSHIBA_RBTX4927 is not set
-# CONFIG_TOSHIBA_RBTX4938 is not set
-CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_GENERIC_FIND_NEXT_BIT=y
-CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_GENERIC_TIME=y
-CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
-CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
-CONFIG_DMA_NONCOHERENT=y
-CONFIG_DMA_NEED_PCI_MAP_STATE=y
-CONFIG_CPU_BIG_ENDIAN=y
-# CONFIG_CPU_LITTLE_ENDIAN is not set
-CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
-CONFIG_IRQ_CPU=y
-CONFIG_IRQ_MV64340=y
-CONFIG_PCI_MARVELL=y
-CONFIG_SWAP_IO_SPACE=y
-CONFIG_MIPS_L1_CACHE_SHIFT=5
-
-#
-# CPU selection
-#
-# CONFIG_CPU_MIPS32_R1 is not set
-# CONFIG_CPU_MIPS32_R2 is not set
-# CONFIG_CPU_MIPS64_R1 is not set
-# CONFIG_CPU_MIPS64_R2 is not set
-# CONFIG_CPU_R3000 is not set
-# CONFIG_CPU_TX39XX is not set
-# CONFIG_CPU_VR41XX is not set
-# CONFIG_CPU_R4300 is not set
-# CONFIG_CPU_R4X00 is not set
-# CONFIG_CPU_TX49XX is not set
-# CONFIG_CPU_R5000 is not set
-# CONFIG_CPU_R5432 is not set
-# CONFIG_CPU_R6000 is not set
-# CONFIG_CPU_NEVADA is not set
-# CONFIG_CPU_R8000 is not set
-# CONFIG_CPU_R10000 is not set
-CONFIG_CPU_RM7000=y
-# CONFIG_CPU_RM9000 is not set
-# CONFIG_CPU_SB1 is not set
-CONFIG_SYS_HAS_CPU_RM7000=y
-CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
-CONFIG_SYS_SUPPORTS_64BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_64BIT_KERNEL=y
-
-#
-# Kernel type
-#
-# CONFIG_32BIT is not set
-CONFIG_64BIT=y
-CONFIG_PAGE_SIZE_4KB=y
-# CONFIG_PAGE_SIZE_8KB is not set
-# CONFIG_PAGE_SIZE_16KB is not set
-# CONFIG_PAGE_SIZE_64KB is not set
-CONFIG_BOARD_SCACHE=y
-CONFIG_RM7000_CPU_SCACHE=y
-CONFIG_CPU_HAS_PREFETCH=y
-CONFIG_MIPS_MT_DISABLED=y
-# CONFIG_MIPS_MT_SMP is not set
-# CONFIG_MIPS_MT_SMTC is not set
-# CONFIG_MIPS_VPE_LOADER is not set
-CONFIG_CPU_HAS_LLSC=y
-CONFIG_CPU_HAS_SYNC=y
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_GENERIC_IRQ_PROBE=y
-CONFIG_CPU_SUPPORTS_HIGHMEM=y
-CONFIG_ARCH_FLATMEM_ENABLE=y
-CONFIG_SELECT_MEMORY_MODEL=y
-CONFIG_FLATMEM_MANUAL=y
-# CONFIG_DISCONTIGMEM_MANUAL is not set
-# CONFIG_SPARSEMEM_MANUAL is not set
-CONFIG_FLATMEM=y
-CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-CONFIG_SPLIT_PTLOCK_CPUS=4
-CONFIG_RESOURCES_64BIT=y
-CONFIG_ZONE_DMA_FLAG=1
-# CONFIG_HZ_48 is not set
-# CONFIG_HZ_100 is not set
-# CONFIG_HZ_128 is not set
-# CONFIG_HZ_250 is not set
-# CONFIG_HZ_256 is not set
-CONFIG_HZ_1000=y
-# CONFIG_HZ_1024 is not set
-CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
-CONFIG_HZ=1000
-CONFIG_PREEMPT_NONE=y
-# CONFIG_PREEMPT_VOLUNTARY is not set
-# CONFIG_PREEMPT is not set
-# CONFIG_KEXEC is not set
-CONFIG_LOCKDEP_SUPPORT=y
-CONFIG_STACKTRACE_SUPPORT=y
-CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-#
-# Code maturity level options
-#
-CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-
-#
-# General setup
-#
-CONFIG_LOCALVERSION=""
-CONFIG_LOCALVERSION_AUTO=y
-CONFIG_SWAP=y
-CONFIG_SYSVIPC=y
-# CONFIG_IPC_NS is not set
-CONFIG_SYSVIPC_SYSCTL=y
-# CONFIG_POSIX_MQUEUE is not set
-# CONFIG_BSD_PROCESS_ACCT is not set
-# CONFIG_TASKSTATS is not set
-# CONFIG_UTS_NS is not set
-# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
-CONFIG_SYSFS_DEPRECATED=y
-CONFIG_RELAY=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-CONFIG_SYSCTL=y
-CONFIG_EMBEDDED=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_EXTRA_PASS is not set
-CONFIG_HOTPLUG=y
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-CONFIG_ELF_CORE=y
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-CONFIG_EPOLL=y
-CONFIG_SHMEM=y
-CONFIG_SLAB=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
-CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
-
-#
-# Loadable module support
-#
-# CONFIG_MODULES is not set
-
-#
-# Block layer
-#
-CONFIG_BLOCK=y
-# CONFIG_BLK_DEV_IO_TRACE is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
-CONFIG_DEFAULT_AS=y
-# CONFIG_DEFAULT_DEADLINE is not set
-# CONFIG_DEFAULT_CFQ is not set
-# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="anticipatory"
-
-#
-# Bus options (PCI, PCMCIA, EISA, ISA, TC)
-#
-CONFIG_HW_HAS_PCI=y
-CONFIG_PCI=y
-CONFIG_MMU=y
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
-# CONFIG_PCCARD is not set
-
-#
-# PCI Hotplug Support
-#
-# CONFIG_HOTPLUG_PCI is not set
-
-#
-# Executable file formats
-#
-CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_MISC is not set
-# CONFIG_BUILD_ELF64 is not set
-CONFIG_MIPS32_COMPAT=y
-CONFIG_COMPAT=y
-CONFIG_SYSVIPC_COMPAT=y
-CONFIG_MIPS32_O32=y
-CONFIG_MIPS32_N32=y
-CONFIG_BINFMT_ELF32=y
-
-#
-# Power management options
-#
-CONFIG_PM=y
-# CONFIG_PM_LEGACY is not set
-# CONFIG_PM_DEBUG is not set
-# CONFIG_PM_SYSFS_DEPRECATED is not set
-
-#
-# Networking
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-# CONFIG_NETDEBUG is not set
-# CONFIG_PACKET is not set
-CONFIG_UNIX=y
-CONFIG_XFRM=y
-CONFIG_XFRM_USER=y
-# CONFIG_XFRM_SUB_POLICY is not set
-CONFIG_XFRM_MIGRATE=y
-CONFIG_NET_KEY=y
-CONFIG_NET_KEY_MIGRATE=y
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-# CONFIG_IP_PNP_BOOTP is not set
-# CONFIG_IP_PNP_RARP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
-# CONFIG_INET_TUNNEL is not set
-CONFIG_INET_XFRM_MODE_TRANSPORT=y
-CONFIG_INET_XFRM_MODE_TUNNEL=y
-CONFIG_INET_XFRM_MODE_BEET=y
-CONFIG_INET_DIAG=y
-CONFIG_INET_TCP_DIAG=y
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_CUBIC=y
-CONFIG_DEFAULT_TCP_CONG="cubic"
-CONFIG_TCP_MD5SIG=y
-# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
-CONFIG_NETWORK_SECMARK=y
-# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
-# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
-# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
-# CONFIG_TIPC is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
-# CONFIG_NET_SCHED is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-CONFIG_IEEE80211=y
-# CONFIG_IEEE80211_DEBUG is not set
-CONFIG_IEEE80211_CRYPT_WEP=y
-CONFIG_IEEE80211_CRYPT_CCMP=y
-CONFIG_IEEE80211_SOFTMAC=y
-# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set
-CONFIG_WIRELESS_EXT=y
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_STANDALONE=y
-CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=y
-# CONFIG_SYS_HYPERVISOR is not set
-
-#
-# Connector - unified userspace <-> kernelspace linker
-#
-CONFIG_CONNECTOR=y
-CONFIG_PROC_EVENTS=y
-
-#
-# Memory Technology Devices (MTD)
-#
-# CONFIG_MTD is not set
-
-#
-# Parallel port support
-#
-# CONFIG_PARPORT is not set
-
-#
-# Plug and Play support
-#
-# CONFIG_PNPACPI is not set
-
-#
-# Block devices
-#
-# CONFIG_BLK_CPQ_DA is not set
-# CONFIG_BLK_CPQ_CISS_DA is not set
-# CONFIG_BLK_DEV_DAC960 is not set
-# CONFIG_BLK_DEV_UMEM is not set
-# CONFIG_BLK_DEV_COW_COMMON is not set
-# CONFIG_BLK_DEV_LOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
-# CONFIG_BLK_DEV_SX8 is not set
-# CONFIG_BLK_DEV_RAM is not set
-# CONFIG_BLK_DEV_INITRD is not set
-CONFIG_CDROM_PKTCDVD=y
-CONFIG_CDROM_PKTCDVD_BUFFERS=8
-# CONFIG_CDROM_PKTCDVD_WCACHE is not set
-CONFIG_ATA_OVER_ETH=y
-
-#
-# Misc devices
-#
-CONFIG_SGI_IOC4=y
-# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-CONFIG_RAID_ATTRS=y
-# CONFIG_SCSI is not set
-# CONFIG_SCSI_NETLINK is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
-# CONFIG_ATA is not set
-
-#
-# Multi-device support (RAID and LVM)
-#
-# CONFIG_MD is not set
-
-#
-# Fusion MPT device support
-#
-# CONFIG_FUSION is not set
-
-#
-# IEEE 1394 (FireWire) support
-#
-# CONFIG_IEEE1394 is not set
-
-#
-# I2O device support
-#
-# CONFIG_I2O is not set
-
-#
-# Network device support
-#
-CONFIG_NETDEVICES=y
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-
-#
-# ARCnet devices
-#
-# CONFIG_ARCNET is not set
-
-#
-# PHY device support
-#
-CONFIG_PHYLIB=y
-
-#
-# MII PHY device drivers
-#
-CONFIG_MARVELL_PHY=y
-CONFIG_DAVICOM_PHY=y
-CONFIG_QSEMI_PHY=y
-CONFIG_LXT_PHY=y
-CONFIG_CICADA_PHY=y
-CONFIG_VITESSE_PHY=y
-CONFIG_SMSC_PHY=y
-# CONFIG_BROADCOM_PHY is not set
-# CONFIG_FIXED_PHY is not set
-
-#
-# Ethernet (10 or 100Mbit)
-#
-CONFIG_NET_ETHERNET=y
-# CONFIG_MII is not set
-# CONFIG_HAPPYMEAL is not set
-# CONFIG_SUNGEM is not set
-# CONFIG_CASSINI is not set
-# CONFIG_NET_VENDOR_3COM is not set
-# CONFIG_DM9000 is not set
-
-#
-# Tulip family network device support
-#
-# CONFIG_NET_TULIP is not set
-# CONFIG_HP100 is not set
-# CONFIG_NET_PCI is not set
-
-#
-# Ethernet (1000 Mbit)
-#
-# CONFIG_ACENIC is not set
-# CONFIG_DL2K is not set
-# CONFIG_E1000 is not set
-# CONFIG_NS83820 is not set
-# CONFIG_HAMACHI is not set
-# CONFIG_YELLOWFIN is not set
-# CONFIG_R8169 is not set
-# CONFIG_SIS190 is not set
-# CONFIG_SKGE is not set
-# CONFIG_SKY2 is not set
-# CONFIG_SK98LIN is not set
-# CONFIG_TIGON3 is not set
-# CONFIG_BNX2 is not set
-# CONFIG_MV643XX_ETH is not set
-CONFIG_QLA3XXX=y
-# CONFIG_ATL1 is not set
-
-#
-# Ethernet (10000 Mbit)
-#
-# CONFIG_CHELSIO_T1 is not set
-CONFIG_CHELSIO_T3=y
-# CONFIG_IXGB is not set
-# CONFIG_S2IO is not set
-# CONFIG_MYRI10GE is not set
-CONFIG_NETXEN_NIC=y
-
-#
-# Token Ring devices
-#
-# CONFIG_TR is not set
-
-#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Wan interfaces
-#
-# CONFIG_WAN is not set
-# CONFIG_FDDI is not set
-# CONFIG_HIPPI is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
-# CONFIG_NETCONSOLE is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-
-#
-# ISDN subsystem
-#
-# CONFIG_ISDN is not set
-
-#
-# Telephony Support
-#
-# CONFIG_PHONE is not set
-
-#
-# Input device support
-#
-CONFIG_INPUT=y
-# CONFIG_INPUT_FF_MEMLESS is not set
-
-#
-# Userland interfaces
-#
-CONFIG_INPUT_MOUSEDEV=y
-CONFIG_INPUT_MOUSEDEV_PSAUX=y
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
-# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
-# CONFIG_INPUT_EVDEV is not set
-# CONFIG_INPUT_EVBUG is not set
-
-#
-# Input Device Drivers
-#
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TOUCHSCREEN is not set
-# CONFIG_INPUT_MISC is not set
-
-#
-# Hardware I/O ports
-#
-CONFIG_SERIO=y
-# CONFIG_SERIO_I8042 is not set
-CONFIG_SERIO_SERPORT=y
-# CONFIG_SERIO_PCIPS2 is not set
-# CONFIG_SERIO_LIBPS2 is not set
-CONFIG_SERIO_RAW=y
-# CONFIG_GAMEPORT is not set
-
-#
-# Character devices
-#
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-CONFIG_HW_CONSOLE=y
-CONFIG_VT_HW_CONSOLE_BINDING=y
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_PCI=y
-CONFIG_SERIAL_8250_NR_UARTS=4
-CONFIG_SERIAL_8250_RUNTIME_UARTS=4
-# CONFIG_SERIAL_8250_EXTENDED is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-# CONFIG_SERIAL_JSM is not set
-CONFIG_UNIX98_PTYS=y
-CONFIG_LEGACY_PTYS=y
-CONFIG_LEGACY_PTY_COUNT=256
-
-#
-# IPMI
-#
-# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
-# CONFIG_WATCHDOG is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_RTC is not set
-# CONFIG_GEN_RTC is not set
-# CONFIG_DTLK is not set
-# CONFIG_R3964 is not set
-# CONFIG_APPLICOM is not set
-# CONFIG_DRM is not set
-# CONFIG_RAW_DRIVER is not set
-
-#
-# TPM devices
-#
-# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
-# CONFIG_I2C is not set
-
-#
-# SPI support
-#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
-
-#
-# Dallas's 1-wire bus
-#
-# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
-# CONFIG_HWMON is not set
-# CONFIG_HWMON_VID is not set
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-
-#
-# Digital Video Broadcasting Devices
-#
-# CONFIG_DVB is not set
-
-#
-# Graphics support
-#
-# CONFIG_FIRMWARE_EDID is not set
-# CONFIG_FB is not set
-
-#
-# Console display driver support
-#
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_DUMMY_CONSOLE=y
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-
-#
-# HID Devices
-#
-# CONFIG_HID is not set
-
-#
-# USB support
-#
-CONFIG_USB_ARCH_HAS_HCD=y
-CONFIG_USB_ARCH_HAS_OHCI=y
-CONFIG_USB_ARCH_HAS_EHCI=y
-# CONFIG_USB is not set
-
-#
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
-#
-
-#
-# USB Gadget Support
-#
-# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
-# CONFIG_MMC is not set
-
-#
-# LED devices
-#
-# CONFIG_NEW_LEDS is not set
-
-#
-# LED drivers
-#
-
-#
-# LED Triggers
-#
-
-#
-# InfiniBand support
-#
-# CONFIG_INFINIBAND is not set
-
-#
-# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
-#
-
-#
-# Real Time Clock
-#
-# CONFIG_RTC_CLASS is not set
-
-#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
-#
-
-#
-# Auxiliary Display support
-#
-
-#
-# Virtualization
-#
-
-#
-# File systems
-#
-CONFIG_EXT2_FS=y
-# CONFIG_EXT2_FS_XATTR is not set
-# CONFIG_EXT2_FS_XIP is not set
-# CONFIG_EXT3_FS is not set
-# CONFIG_EXT4DEV_FS is not set
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-CONFIG_FS_POSIX_ACL=y
-# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
-# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
-CONFIG_INOTIFY=y
-CONFIG_INOTIFY_USER=y
-# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-CONFIG_FUSE_FS=y
-CONFIG_GENERIC_ACL=y
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_PROC_KCORE=y
-CONFIG_PROC_SYSCTL=y
-CONFIG_SYSFS=y
-CONFIG_TMPFS=y
-CONFIG_TMPFS_POSIX_ACL=y
-# CONFIG_HUGETLB_PAGE is not set
-CONFIG_RAMFS=y
-CONFIG_CONFIGFS_FS=y
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_ECRYPT_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
-CONFIG_NFS_FS=y
-# CONFIG_NFS_V3 is not set
-# CONFIG_NFS_V4 is not set
-# CONFIG_NFS_DIRECTIO is not set
-CONFIG_NFSD=y
-# CONFIG_NFSD_V3 is not set
-# CONFIG_NFSD_TCP is not set
-CONFIG_ROOT_NFS=y
-CONFIG_LOCKD=y
-CONFIG_EXPORTFS=y
-CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=y
-# CONFIG_RPCSEC_GSS_KRB5 is not set
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-# CONFIG_9P_FS is not set
-
-#
-# Partition Types
-#
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_MSDOS_PARTITION=y
-
-#
-# Native Language Support
-#
-# CONFIG_NLS is not set
-
-#
-# Distributed Lock Manager
-#
-CONFIG_DLM=y
-CONFIG_DLM_TCP=y
-# CONFIG_DLM_SCTP is not set
-# CONFIG_DLM_DEBUG is not set
-
-#
-# Profiling support
-#
-# CONFIG_PROFILING is not set
-
-#
-# Kernel hacking
-#
-CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-# CONFIG_PRINTK_TIME is not set
-CONFIG_ENABLE_MUST_CHECK=y
-# CONFIG_MAGIC_SYSRQ is not set
-# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
-# CONFIG_HEADERS_CHECK is not set
-# CONFIG_DEBUG_KERNEL is not set
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_CROSSCOMPILE=y
-CONFIG_CMDLINE=""
-
-#
-# Security options
-#
-CONFIG_KEYS=y
-CONFIG_KEYS_DEBUG_PROC_KEYS=y
-# CONFIG_SECURITY is not set
-
-#
-# Cryptographic options
-#
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_ALGAPI=y
-CONFIG_CRYPTO_BLKCIPHER=y
-CONFIG_CRYPTO_HASH=y
-CONFIG_CRYPTO_MANAGER=y
-CONFIG_CRYPTO_HMAC=y
-CONFIG_CRYPTO_XCBC=y
-CONFIG_CRYPTO_NULL=y
-CONFIG_CRYPTO_MD4=y
-CONFIG_CRYPTO_MD5=y
-CONFIG_CRYPTO_SHA1=y
-CONFIG_CRYPTO_SHA256=y
-CONFIG_CRYPTO_SHA512=y
-CONFIG_CRYPTO_WP512=y
-CONFIG_CRYPTO_TGR192=y
-CONFIG_CRYPTO_GF128MUL=y
-CONFIG_CRYPTO_ECB=y
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_PCBC=y
-CONFIG_CRYPTO_LRW=y
-CONFIG_CRYPTO_DES=y
-CONFIG_CRYPTO_FCRYPT=y
-CONFIG_CRYPTO_BLOWFISH=y
-CONFIG_CRYPTO_TWOFISH=y
-CONFIG_CRYPTO_TWOFISH_COMMON=y
-CONFIG_CRYPTO_SERPENT=y
-CONFIG_CRYPTO_AES=y
-CONFIG_CRYPTO_CAST5=y
-CONFIG_CRYPTO_CAST6=y
-CONFIG_CRYPTO_TEA=y
-CONFIG_CRYPTO_ARC4=y
-CONFIG_CRYPTO_KHAZAD=y
-CONFIG_CRYPTO_ANUBIS=y
-CONFIG_CRYPTO_DEFLATE=y
-CONFIG_CRYPTO_MICHAEL_MIC=y
-CONFIG_CRYPTO_CRC32C=y
-CONFIG_CRYPTO_CAMELLIA=y
-
-#
-# Hardware crypto devices
-#
-
-#
-# Library routines
-#
-CONFIG_BITREVERSE=y
-# CONFIG_CRC_CCITT is not set
-CONFIG_CRC16=y
-CONFIG_CRC32=y
-CONFIG_LIBCRC32C=y
-CONFIG_ZLIB_INFLATE=y
-CONFIG_ZLIB_DEFLATE=y
-CONFIG_PLIST=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
# CONFIG_MOMENCO_JAGUAR_ATX is not set
CONFIG_MOMENCO_OCELOT=y
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
CONFIG_PNX8550_JBS=y
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MOMENCO_OCELOT_3 is not set
-# CONFIG_MOMENCO_OCELOT_C is not set
# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
+++ /dev/null
-#
-# Makefile for Momentum Computer's Ocelot-C and -CS boards.
-#
-
-obj-y += cpci-irq.o irq.o platform.o prom.o reset.o \
- setup.o uart-irq.o
-
-obj-$(CONFIG_KGDB) += dbg_io.o
+++ /dev/null
-/*
- * Copyright 2002 Momentum Computer
- * Author: mdharm@momenco.com
- *
- * arch/mips/momentum/ocelot_c/cpci-irq.c
- * Interrupt routines for cpci. Interrupt numbers are assigned from
- * CPCI_IRQ_BASE to CPCI_IRQ_BASE+8 (8 interrupt sources).
- *
- * Note that the high-level software will need to be careful about using
- * these interrupts. If this board is asserting a cPCI interrupt, it will
- * also see the asserted interrupt. Care must be taken to avoid an
- * interrupt flood.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/kernel_stat.h>
-#include <asm/io.h>
-#include "ocelot_c_fpga.h"
-
-#define CPCI_IRQ_BASE 8
-
-static inline int ls1bit8(unsigned int x)
-{
- int b = 7, s;
-
- s = 4; if (((unsigned char)(x << 4)) == 0) s = 0; b -= s; x <<= s;
- s = 2; if (((unsigned char)(x << 2)) == 0) s = 0; b -= s; x <<= s;
- s = 1; if (((unsigned char)(x << 1)) == 0) s = 0; b -= s;
-
- return b;
-}
-
-/* mask off an interrupt -- 0 is enable, 1 is disable */
-static inline void mask_cpci_irq(unsigned int irq)
-{
- uint32_t value;
-
- value = OCELOT_FPGA_READ(INTMASK);
- value |= 1 << (irq - CPCI_IRQ_BASE);
- OCELOT_FPGA_WRITE(value, INTMASK);
-
- /* read the value back to assure that it's really been written */
- value = OCELOT_FPGA_READ(INTMASK);
-}
-
-/* unmask an interrupt -- 0 is enable, 1 is disable */
-static inline void unmask_cpci_irq(unsigned int irq)
-{
- uint32_t value;
-
- value = OCELOT_FPGA_READ(INTMASK);
- value &= ~(1 << (irq - CPCI_IRQ_BASE));
- OCELOT_FPGA_WRITE(value, INTMASK);
-
- /* read the value back to assure that it's really been written */
- value = OCELOT_FPGA_READ(INTMASK);
-}
-
-/*
- * Interrupt handler for interrupts coming from the FPGA chip.
- * It could be built in ethernet ports etc...
- */
-void ll_cpci_irq(void)
-{
- unsigned int irq_src, irq_mask;
-
- /* read the interrupt status registers */
- irq_src = OCELOT_FPGA_READ(INTSTAT);
- irq_mask = OCELOT_FPGA_READ(INTMASK);
-
- /* mask for just the interrupts we want */
- irq_src &= ~irq_mask;
-
- do_IRQ(ls1bit8(irq_src) + CPCI_IRQ_BASE);
-}
-
-struct irq_chip cpci_irq_type = {
- .name = "CPCI/FPGA",
- .ack = mask_cpci_irq,
- .mask = mask_cpci_irq,
- .mask_ack = mask_cpci_irq,
- .unmask = unmask_cpci_irq,
-};
-
-void cpci_irq_init(void)
-{
- int i;
-
- for (i = CPCI_IRQ_BASE; i < (CPCI_IRQ_BASE + 8); i++)
- set_irq_chip_and_handler(i, &cpci_irq_type, handle_level_irq);
-}
+++ /dev/null
-
-#include <asm/serial.h> /* For the serial port location and base baud */
-
-/* --- CONFIG --- */
-
-typedef unsigned char uint8;
-typedef unsigned int uint32;
-
-/* --- END OF CONFIG --- */
-
-#define UART16550_BAUD_2400 2400
-#define UART16550_BAUD_4800 4800
-#define UART16550_BAUD_9600 9600
-#define UART16550_BAUD_19200 19200
-#define UART16550_BAUD_38400 38400
-#define UART16550_BAUD_57600 57600
-#define UART16550_BAUD_115200 115200
-
-#define UART16550_PARITY_NONE 0
-#define UART16550_PARITY_ODD 0x08
-#define UART16550_PARITY_EVEN 0x18
-#define UART16550_PARITY_MARK 0x28
-#define UART16550_PARITY_SPACE 0x38
-
-#define UART16550_DATA_5BIT 0x0
-#define UART16550_DATA_6BIT 0x1
-#define UART16550_DATA_7BIT 0x2
-#define UART16550_DATA_8BIT 0x3
-
-#define UART16550_STOP_1BIT 0x0
-#define UART16550_STOP_2BIT 0x4
-
-/* ----------------------------------------------------- */
-
-/* === CONFIG === */
-
-/* [jsun] we use the second serial port for kdb */
-#define BASE OCELOT_SERIAL1_BASE
-#define MAX_BAUD OCELOT_BASE_BAUD
-
-/* === END OF CONFIG === */
-
-#define REG_OFFSET 4
-
-/* register offset */
-#define OFS_RCV_BUFFER 0
-#define OFS_TRANS_HOLD 0
-#define OFS_SEND_BUFFER 0
-#define OFS_INTR_ENABLE (1*REG_OFFSET)
-#define OFS_INTR_ID (2*REG_OFFSET)
-#define OFS_DATA_FORMAT (3*REG_OFFSET)
-#define OFS_LINE_CONTROL (3*REG_OFFSET)
-#define OFS_MODEM_CONTROL (4*REG_OFFSET)
-#define OFS_RS232_OUTPUT (4*REG_OFFSET)
-#define OFS_LINE_STATUS (5*REG_OFFSET)
-#define OFS_MODEM_STATUS (6*REG_OFFSET)
-#define OFS_RS232_INPUT (6*REG_OFFSET)
-#define OFS_SCRATCH_PAD (7*REG_OFFSET)
-
-#define OFS_DIVISOR_LSB (0*REG_OFFSET)
-#define OFS_DIVISOR_MSB (1*REG_OFFSET)
-
-
-/* memory-mapped read/write of the port */
-#define UART16550_READ(y) (*((volatile uint8*)(BASE + y)))
-#define UART16550_WRITE(y, z) ((*((volatile uint8*)(BASE + y))) = z)
-
-void debugInit(uint32 baud, uint8 data, uint8 parity, uint8 stop)
-{
- /* disable interrupts */
- UART16550_WRITE(OFS_INTR_ENABLE, 0);
-
- /* set up baud rate */
- {
- uint32 divisor;
-
- /* set DIAB bit */
- UART16550_WRITE(OFS_LINE_CONTROL, 0x80);
-
- /* set divisor */
- divisor = MAX_BAUD / baud;
- UART16550_WRITE(OFS_DIVISOR_LSB, divisor & 0xff);
- UART16550_WRITE(OFS_DIVISOR_MSB, (divisor & 0xff00) >> 8);
-
- /* clear DIAB bit */
- UART16550_WRITE(OFS_LINE_CONTROL, 0x0);
- }
-
- /* set data format */
- UART16550_WRITE(OFS_DATA_FORMAT, data | parity | stop);
-}
-
-static int remoteDebugInitialized = 0;
-
-uint8 getDebugChar(void)
-{
- if (!remoteDebugInitialized) {
- remoteDebugInitialized = 1;
- debugInit(UART16550_BAUD_38400,
- UART16550_DATA_8BIT,
- UART16550_PARITY_NONE, UART16550_STOP_1BIT);
- }
-
- while ((UART16550_READ(OFS_LINE_STATUS) & 0x1) == 0);
- return UART16550_READ(OFS_RCV_BUFFER);
-}
-
-
-int putDebugChar(uint8 byte)
-{
- if (!remoteDebugInitialized) {
- remoteDebugInitialized = 1;
- debugInit(UART16550_BAUD_38400,
- UART16550_DATA_8BIT,
- UART16550_PARITY_NONE, UART16550_STOP_1BIT);
- }
-
- while ((UART16550_READ(OFS_LINE_STATUS) & 0x20) == 0);
- UART16550_WRITE(OFS_SEND_BUFFER, byte);
- return 1;
-}
+++ /dev/null
-/*
- * Copyright (C) 2000 RidgeRun, Inc.
- * Author: RidgeRun, Inc.
- * glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com
- *
- * Copyright 2001 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- * Copyright (C) 2000, 01, 05 Ralf Baechle (ralf@linux-mips.org)
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- */
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/kernel_stat.h>
-#include <linux/module.h>
-#include <linux/signal.h>
-#include <linux/sched.h>
-#include <linux/types.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/timex.h>
-#include <linux/slab.h>
-#include <linux/random.h>
-#include <linux/bitops.h>
-#include <linux/mv643xx.h>
-#include <asm/bootinfo.h>
-#include <asm/io.h>
-#include <asm/irq_cpu.h>
-#include <asm/mipsregs.h>
-#include <asm/system.h>
-
-extern void uart_irq_init(void);
-extern void cpci_irq_init(void);
-
-static struct irqaction cascade_fpga = {
- no_action, IRQF_DISABLED, CPU_MASK_NONE, "cascade via FPGA", NULL, NULL
-};
-
-static struct irqaction cascade_mv64340 = {
- no_action, IRQF_DISABLED, CPU_MASK_NONE, "cascade via MV64340", NULL, NULL
-};
-
-extern void ll_uart_irq(void);
-extern void ll_cpci_irq(void);
-
-asmlinkage void plat_irq_dispatch(void)
-{
- unsigned int pending = read_c0_cause() & read_c0_status() & ST0_IM;
-
- if (pending & STATUSF_IP0)
- do_IRQ(0);
- else if (pending & STATUSF_IP1)
- do_IRQ(1);
- else if (pending & STATUSF_IP2)
- do_IRQ(2);
- else if (pending & STATUSF_IP3)
- ll_uart_irq();
- else if (pending & STATUSF_IP4)
- do_IRQ(4);
- else if (pending & STATUSF_IP5)
- ll_cpci_irq();
- else if (pending & STATUSF_IP6)
- ll_mv64340_irq();
- else if (pending & STATUSF_IP7)
- do_IRQ(7);
- else
- spurious_interrupt();
-}
-
-void __init arch_init_irq(void)
-{
- /*
- * Clear all of the interrupts while we change the able around a bit.
- * int-handler is not on bootstrap
- */
- clear_c0_status(ST0_IM);
-
- mips_cpu_irq_init();
-
- /* set up the cascading interrupts */
- setup_irq(3, &cascade_fpga);
- setup_irq(5, &cascade_fpga);
- setup_irq(6, &cascade_mv64340);
-
- mv64340_irq_init(16);
- uart_irq_init();
- cpci_irq_init();
-}
+++ /dev/null
-/*
- * Ocelot-C Board Register Definitions
- *
- * (C) 2002 Momentum Computer Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * Louis Hamilton, Red Hat, Inc.
- * hamilton@redhat.com [MIPS64 modifications]
- */
-
-#ifndef __OCELOT_C_FPGA_H__
-#define __OCELOT_C_FPGA_H__
-
-
-#ifdef CONFIG_64BIT
-#define OCELOT_C_CS0_ADDR (0xfffffffffc000000)
-#else
-#define OCELOT_C_CS0_ADDR (0xfc000000)
-#endif
-
-#define OCELOT_C_REG_BOARDREV 0x0
-#define OCELOT_C_REG_FPGA_REV 0x1
-#define OCELOT_C_REG_FPGA_TYPE 0x2
-#define OCELOT_C_REG_RESET_STATUS 0x3
-#define OCELOT_C_REG_BOARD_STATUS 0x4
-#define OCELOT_C_REG_CPCI_ID 0x5
-#define OCELOT_C_REG_SET 0x6
-#define OCELOT_C_REG_CLR 0x7
-#define OCELOT_C_REG_EEPROM_MODE 0x9
-#define OCELOT_C_REG_INTMASK 0xa
-#define OCELOT_C_REG_INTSTAT 0xb
-#define OCELOT_C_REG_UART_INTMASK 0xc
-#define OCELOT_C_REG_UART_INTSTAT 0xd
-#define OCELOT_C_REG_INTSET 0xe
-#define OCELOT_C_REG_INTCLR 0xf
-
-#define __FPGA_REG_TO_ADDR(reg) \
- ((void *) OCELOT_C_CS0_ADDR + OCELOT_C_REG_##reg)
-#define OCELOT_FPGA_WRITE(x, reg) writeb(x, __FPGA_REG_TO_ADDR(reg))
-#define OCELOT_FPGA_READ(reg) readb(__FPGA_REG_TO_ADDR(reg))
-
-#endif
+++ /dev/null
-#include <linux/delay.h>
-#include <linux/if_ether.h>
-#include <linux/ioport.h>
-#include <linux/mv643xx.h>
-#include <linux/platform_device.h>
-
-#include "ocelot_c_fpga.h"
-
-#if defined(CONFIG_MV643XX_ETH) || defined(CONFIG_MV643XX_ETH_MODULE)
-
-static struct resource mv643xx_eth_shared_resources[] = {
- [0] = {
- .name = "ethernet shared base",
- .start = 0xf1000000 + MV643XX_ETH_SHARED_REGS,
- .end = 0xf1000000 + MV643XX_ETH_SHARED_REGS +
- MV643XX_ETH_SHARED_REGS_SIZE - 1,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device mv643xx_eth_shared_device = {
- .name = MV643XX_ETH_SHARED_NAME,
- .id = 0,
- .num_resources = ARRAY_SIZE(mv643xx_eth_shared_resources),
- .resource = mv643xx_eth_shared_resources,
-};
-
-#define MV_SRAM_BASE 0xfe000000UL
-#define MV_SRAM_SIZE (256 * 1024)
-
-#define MV_SRAM_RXRING_SIZE (MV_SRAM_SIZE / 4)
-#define MV_SRAM_TXRING_SIZE (MV_SRAM_SIZE / 4)
-
-#define MV_SRAM_BASE_ETH0 MV_SRAM_BASE
-#define MV_SRAM_BASE_ETH1 (MV_SRAM_BASE + (MV_SRAM_SIZE / 2))
-
-#define MV64x60_IRQ_ETH_0 48
-#define MV64x60_IRQ_ETH_1 49
-
-static struct resource mv64x60_eth0_resources[] = {
- [0] = {
- .name = "eth0 irq",
- .start = MV64x60_IRQ_ETH_0,
- .end = MV64x60_IRQ_ETH_0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct mv643xx_eth_platform_data eth0_pd = {
- .port_number = 0,
-
- .tx_sram_addr = MV_SRAM_BASE_ETH0,
- .tx_sram_size = MV_SRAM_TXRING_SIZE,
- .tx_queue_size = MV_SRAM_TXRING_SIZE / 16,
-
- .rx_sram_addr = MV_SRAM_BASE_ETH0 + MV_SRAM_TXRING_SIZE,
- .rx_sram_size = MV_SRAM_RXRING_SIZE,
- .rx_queue_size = MV_SRAM_RXRING_SIZE / 16,
-};
-
-static struct platform_device eth0_device = {
- .name = MV643XX_ETH_NAME,
- .id = 0,
- .num_resources = ARRAY_SIZE(mv64x60_eth0_resources),
- .resource = mv64x60_eth0_resources,
- .dev = {
- .platform_data = ð0_pd,
- },
-};
-
-static struct resource mv64x60_eth1_resources[] = {
- [0] = {
- .name = "eth1 irq",
- .start = MV64x60_IRQ_ETH_1,
- .end = MV64x60_IRQ_ETH_1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct mv643xx_eth_platform_data eth1_pd = {
- .port_number = 1,
-
- .tx_sram_addr = MV_SRAM_BASE_ETH1,
- .tx_sram_size = MV_SRAM_TXRING_SIZE,
- .tx_queue_size = MV_SRAM_TXRING_SIZE / 16,
-
- .rx_sram_addr = MV_SRAM_BASE_ETH1 + MV_SRAM_TXRING_SIZE,
- .rx_sram_size = MV_SRAM_RXRING_SIZE,
- .rx_queue_size = MV_SRAM_RXRING_SIZE / 16,
-};
-
-static struct platform_device eth1_device = {
- .name = MV643XX_ETH_NAME,
- .id = 1,
- .num_resources = ARRAY_SIZE(mv64x60_eth1_resources),
- .resource = mv64x60_eth1_resources,
- .dev = {
- .platform_data = ð1_pd,
- },
-};
-
-static struct platform_device *mv643xx_eth_pd_devs[] __initdata = {
- &mv643xx_eth_shared_device,
- ð0_device,
- ð1_device,
- /* The third port is not wired up on the Ocelot C */
-};
-
-static u8 __init exchange_bit(u8 val, u8 cs)
-{
- /* place the data */
- OCELOT_FPGA_WRITE((val << 2) | cs, EEPROM_MODE);
- udelay(1);
-
- /* turn the clock on */
- OCELOT_FPGA_WRITE((val << 2) | cs | 0x2, EEPROM_MODE);
- udelay(1);
-
- /* turn the clock off and read-strobe */
- OCELOT_FPGA_WRITE((val << 2) | cs | 0x10, EEPROM_MODE);
-
- /* return the data */
- return (OCELOT_FPGA_READ(EEPROM_MODE) >> 3) & 0x1;
-}
-
-static void __init get_mac(char dest[6])
-{
- u8 read_opcode[12] = {1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0};
- int i,j;
-
- for (i = 0; i < 12; i++)
- exchange_bit(read_opcode[i], 1);
-
- for (j = 0; j < 6; j++) {
- dest[j] = 0;
- for (i = 0; i < 8; i++) {
- dest[j] <<= 1;
- dest[j] |= exchange_bit(0, 1);
- }
- }
-
- /* turn off CS */
- exchange_bit(0,0);
-}
-
-/*
- * Copy and increment ethernet MAC address by a small value.
- *
- * This is useful for systems where the only one MAC address is stored in
- * non-volatile memory for multiple ports.
- */
-static inline void eth_mac_add(unsigned char *dst, unsigned char *src,
- unsigned int add)
-{
- int i;
-
- BUG_ON(add >= 256);
-
- for (i = ETH_ALEN; i >= 0; i--) {
- dst[i] = src[i] + add;
- add = dst[i] < src[i]; /* compute carry */
- }
-
- WARN_ON(add);
-}
-
-static int __init mv643xx_eth_add_pds(void)
-{
- unsigned char mac[ETH_ALEN];
- int ret;
-
- get_mac(mac);
- eth_mac_add(eth0_pd.mac_addr, mac, 0);
- eth_mac_add(eth1_pd.mac_addr, mac, 1);
- ret = platform_add_devices(mv643xx_eth_pd_devs,
- ARRAY_SIZE(mv643xx_eth_pd_devs));
-
- return ret;
-}
-
-device_initcall(mv643xx_eth_add_pds);
-
-#endif /* defined(CONFIG_MV643XX_ETH) || defined(CONFIG_MV643XX_ETH_MODULE) */
+++ /dev/null
-/*
- * Copyright 2002 Momentum Computer Inc.
- * Author: Matthew Dharm <mdharm@momenco.com>
- *
- * Louis Hamilton, Red Hat, Inc.
- * hamilton@redhat.com [MIPS64 modifications]
- *
- * Based on Ocelot Linux port, which is
- * Copyright 2001 MontaVista Software Inc.
- * Author: jsun@mvista.com or jsun@junsun.net
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/bootmem.h>
-#include <linux/mv643xx.h>
-
-#include <asm/addrspace.h>
-#include <asm/bootinfo.h>
-#include <asm/pmon.h>
-
-#include "ocelot_c_fpga.h"
-
-struct callvectors* debug_vectors;
-
-extern unsigned long marvell_base;
-extern unsigned int cpu_clock;
-
-const char *get_system_type(void)
-{
-#ifdef CONFIG_CPU_SR71000
- return "Momentum Ocelot-CS";
-#else
- return "Momentum Ocelot-C";
-#endif
-}
-
-#ifdef CONFIG_64BIT
-
-unsigned long signext(unsigned long addr)
-{
- addr &= 0xffffffff;
- return (unsigned long)((int)addr);
-}
-
-void *get_arg(unsigned long args, int arc)
-{
- unsigned long ul;
- unsigned char *puc, uc;
-
- args += (arc * 4);
- ul = (unsigned long)signext(args);
- puc = (unsigned char *)ul;
- if (puc == 0)
- return (void *)0;
-
-#ifdef CONFIG_CPU_LITTLE_ENDIAN
- uc = *puc++;
- ul = (unsigned long)uc;
- uc = *puc++;
- ul |= (((unsigned long)uc) << 8);
- uc = *puc++;
- ul |= (((unsigned long)uc) << 16);
- uc = *puc++;
- ul |= (((unsigned long)uc) << 24);
-#else /* CONFIG_CPU_LITTLE_ENDIAN */
- uc = *puc++;
- ul = ((unsigned long)uc) << 24;
- uc = *puc++;
- ul |= (((unsigned long)uc) << 16);
- uc = *puc++;
- ul |= (((unsigned long)uc) << 8);
- uc = *puc++;
- ul |= ((unsigned long)uc);
-#endif /* CONFIG_CPU_LITTLE_ENDIAN */
- ul = signext(ul);
- return (void *)ul;
-}
-
-char *arg64(unsigned long addrin, int arg_index)
-{
- unsigned long args;
- char *p;
- args = signext(addrin);
- p = (char *)get_arg(args, arg_index);
- return p;
-}
-#endif /* CONFIG_64BIT */
-
-
-void __init prom_init(void)
-{
- int argc = fw_arg0;
- char **arg = (char **) fw_arg1;
- char **env = (char **) fw_arg2;
- struct callvectors *cv = (struct callvectors *) fw_arg3;
- int i;
-
-#ifdef CONFIG_64BIT
- char *ptr;
-
- printk("prom_init - MIPS64\n");
- /* save the PROM vectors for debugging use */
- debug_vectors = (struct callvectors *)signext((unsigned long)cv);
-
- /* arg[0] is "g", the rest is boot parameters */
- arcs_cmdline[0] = '\0';
-
- for (i = 1; i < argc; i++) {
- ptr = (char *)arg64((unsigned long)arg, i);
- if ((strlen(arcs_cmdline) + strlen(ptr) + 1) >=
- sizeof(arcs_cmdline))
- break;
- strcat(arcs_cmdline, ptr);
- strcat(arcs_cmdline, " ");
- }
- i = 0;
- while (1) {
- ptr = (char *)arg64((unsigned long)env, i);
- if (! ptr)
- break;
-
- if (strncmp("gtbase", ptr, strlen("gtbase")) == 0) {
- marvell_base = simple_strtol(ptr + strlen("gtbase="),
- NULL, 16);
-
- if ((marvell_base & 0xffffffff00000000) == 0)
- marvell_base |= 0xffffffff00000000;
-
- printk("marvell_base set to 0x%016lx\n", marvell_base);
- }
- if (strncmp("cpuclock", ptr, strlen("cpuclock")) == 0) {
- cpu_clock = simple_strtol(ptr + strlen("cpuclock="),
- NULL, 10);
- printk("cpu_clock set to %d\n", cpu_clock);
- }
- i++;
- }
- printk("arcs_cmdline: %s\n", arcs_cmdline);
-
-#else /* CONFIG_64BIT */
- /* save the PROM vectors for debugging use */
- debug_vectors = cv;
-
- /* arg[0] is "g", the rest is boot parameters */
- arcs_cmdline[0] = '\0';
- for (i = 1; i < argc; i++) {
- if (strlen(arcs_cmdline) + strlen(arg[i] + 1)
- >= sizeof(arcs_cmdline))
- break;
- strcat(arcs_cmdline, arg[i]);
- strcat(arcs_cmdline, " ");
- }
-
- while (*env) {
- if (strncmp("gtbase", *env, strlen("gtbase")) == 0) {
- marvell_base = simple_strtol(*env + strlen("gtbase="),
- NULL, 16);
- }
- if (strncmp("cpuclock", *env, strlen("cpuclock")) == 0) {
- cpu_clock = simple_strtol(*env + strlen("cpuclock="),
- NULL, 10);
- }
- env++;
- }
-#endif /* CONFIG_64BIT */
-
- mips_machgroup = MACH_GROUP_MOMENCO;
- mips_machtype = MACH_MOMENCO_OCELOT_C;
-
-#ifndef CONFIG_64BIT
- debug_vectors->printf("Booting Linux kernel...\n");
-#endif
-}
-
-void __init prom_free_prom_memory(void)
-{
-}
+++ /dev/null
-/*
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * Copyright (C) 1997, 2001 Ralf Baechle
- * Copyright 2001 MontaVista Software Inc.
- * Author: jsun@mvista.com or jsun@junsun.net
- *
- * Copyright (C) 2002 Momentum Computer Inc.
- * Author: Matthew Dharm <mdharm@momenco.com>
- *
- * Louis Hamilton, Red Hat, Inc.
- * hamilton@redhat.com [MIPS64 modifications]
- */
-#include <linux/sched.h>
-#include <linux/mm.h>
-#include <asm/io.h>
-#include <asm/pgtable.h>
-#include <asm/processor.h>
-#include <asm/reboot.h>
-#include <asm/system.h>
-#include <linux/delay.h>
-
-void momenco_ocelot_restart(char *command)
-{
- /* base address of timekeeper portion of part */
- void *nvram = (void *)
-#ifdef CONFIG_64BIT
- 0xfffffffffc807000;
-#else
- 0xfc807000;
-#endif
-
- /* Ask the NVRAM/RTC/watchdog chip to assert reset in 1/16 second */
- writeb(0x84, nvram + 0xff7);
-
- /* wait for the watchdog to go off */
- mdelay(100+(1000/16));
-
- /* if the watchdog fails for some reason, let people know */
- printk(KERN_NOTICE "Watchdog reset failed\n");
-}
-
-void momenco_ocelot_halt(void)
-{
- printk(KERN_NOTICE "\n** You can safely turn off the power\n");
- while (1)
- __asm__(".set\tmips3\n\t"
- "wait\n\t"
- ".set\tmips0");
-}
-
-void momenco_ocelot_power_off(void)
-{
- momenco_ocelot_halt();
-}
+++ /dev/null
-/*
- * BRIEF MODULE DESCRIPTION
- * Momentum Computer Ocelot-C and -CS board dependent boot routines
- *
- * Copyright (C) 1996, 1997, 2001 Ralf Baechle
- * Copyright (C) 2000 RidgeRun, Inc.
- * Copyright (C) 2001 Red Hat, Inc.
- * Copyright (C) 2002 Momentum Computer
- *
- * Author: Matthew Dharm, Momentum Computer
- * mdharm@momenco.com
- *
- * Louis Hamilton, Red Hat, Inc.
- * hamilton@redhat.com [MIPS64 modifications]
- *
- * Author: RidgeRun, Inc.
- * glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com
- *
- * Copyright 2001 MontaVista Software Inc.
- * Author: jsun@mvista.com or jsun@junsun.net
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- */
-#include <linux/bcd.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/mm.h>
-#include <linux/swap.h>
-#include <linux/ioport.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/pci.h>
-#include <linux/pm.h>
-#include <linux/timex.h>
-#include <linux/vmalloc.h>
-#include <linux/mv643xx.h>
-
-#include <asm/time.h>
-#include <asm/bootinfo.h>
-#include <asm/page.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/pci.h>
-#include <asm/processor.h>
-#include <asm/reboot.h>
-#include <asm/marvell.h>
-#include <linux/bootmem.h>
-#include <linux/blkdev.h>
-#include "ocelot_c_fpga.h"
-
-unsigned long marvell_base;
-unsigned int cpu_clock;
-
-/* These functions are used for rebooting or halting the machine*/
-extern void momenco_ocelot_restart(char *command);
-extern void momenco_ocelot_halt(void);
-extern void momenco_ocelot_power_off(void);
-
-void momenco_time_init(void);
-
-static char reset_reason;
-
-void add_wired_entry(unsigned long entrylo0, unsigned long entrylo1, unsigned long entryhi, unsigned long pagemask);
-
-static unsigned long ENTRYLO(unsigned long paddr)
-{
- return ((paddr & PAGE_MASK) |
- (_PAGE_PRESENT | __READABLE | __WRITEABLE | _PAGE_GLOBAL |
- _CACHE_UNCACHED)) >> 6;
-}
-
-/* setup code for a handoff from a version 2 PMON 2000 PROM */
-void PMON_v2_setup(void)
-{
- /* Some wired TLB entries for the MV64340 and perhiperals. The
- MV64340 is going to be hit on every IRQ anyway - there's
- absolutely no point in letting it be a random TLB entry, as
- it'll just cause needless churning of the TLB. And we use
- the other half for the serial port, which is just a PITA
- otherwise :)
-
- Device Physical Virtual
- MV64340 Internal Regs 0xf4000000 0xf4000000
- Ocelot-C[S] PLD (CS0) 0xfc000000 0xfc000000
- NVRAM (CS1) 0xfc800000 0xfc800000
- UARTs (CS2) 0xfd000000 0xfd000000
- Internal SRAM 0xfe000000 0xfe000000
- M-Systems DOC (CS3) 0xff000000 0xff000000
- */
- printk("PMON_v2_setup\n");
-
-#ifdef CONFIG_64BIT
- /* marvell and extra space */
- add_wired_entry(ENTRYLO(0xf4000000), ENTRYLO(0xf4010000), 0xfffffffff4000000, PM_64K);
- /* fpga, rtc, and uart */
- add_wired_entry(ENTRYLO(0xfc000000), ENTRYLO(0xfd000000), 0xfffffffffc000000, PM_16M);
- /* m-sys and internal SRAM */
- add_wired_entry(ENTRYLO(0xfe000000), ENTRYLO(0xff000000), 0xfffffffffe000000, PM_16M);
-
- marvell_base = 0xfffffffff4000000;
-#else
- /* marvell and extra space */
- add_wired_entry(ENTRYLO(0xf4000000), ENTRYLO(0xf4010000), 0xf4000000, PM_64K);
- /* fpga, rtc, and uart */
- add_wired_entry(ENTRYLO(0xfc000000), ENTRYLO(0xfd000000), 0xfc000000, PM_16M);
- /* m-sys and internal SRAM */
- add_wired_entry(ENTRYLO(0xfe000000), ENTRYLO(0xff000000), 0xfe000000, PM_16M);
-
- marvell_base = 0xf4000000;
-#endif
-}
-
-unsigned long m48t37y_get_time(void)
-{
-#ifdef CONFIG_64BIT
- unsigned char *rtc_base = (unsigned char*)0xfffffffffc800000;
-#else
- unsigned char* rtc_base = (unsigned char*)0xfc800000;
-#endif
- unsigned int year, month, day, hour, min, sec;
- unsigned long flags;
-
- spin_lock_irqsave(&rtc_lock, flags);
- /* stop the update */
- rtc_base[0x7ff8] = 0x40;
-
- year = BCD2BIN(rtc_base[0x7fff]);
- year += BCD2BIN(rtc_base[0x7ff1]) * 100;
-
- month = BCD2BIN(rtc_base[0x7ffe]);
-
- day = BCD2BIN(rtc_base[0x7ffd]);
-
- hour = BCD2BIN(rtc_base[0x7ffb]);
- min = BCD2BIN(rtc_base[0x7ffa]);
- sec = BCD2BIN(rtc_base[0x7ff9]);
-
- /* start the update */
- rtc_base[0x7ff8] = 0x00;
- spin_unlock_irqrestore(&rtc_lock, flags);
-
- return mktime(year, month, day, hour, min, sec);
-}
-
-int m48t37y_set_time(unsigned long sec)
-{
-#ifdef CONFIG_64BIT
- unsigned char* rtc_base = (unsigned char*)0xfffffffffc800000;
-#else
- unsigned char* rtc_base = (unsigned char*)0xfc800000;
-#endif
- struct rtc_time tm;
- unsigned long flags;
-
- /* convert to a more useful format -- note months count from 0 */
- to_tm(sec, &tm);
- tm.tm_mon += 1;
-
- spin_lock_irqsave(&rtc_lock, flags);
- /* enable writing */
- rtc_base[0x7ff8] = 0x80;
-
- /* year */
- rtc_base[0x7fff] = BIN2BCD(tm.tm_year % 100);
- rtc_base[0x7ff1] = BIN2BCD(tm.tm_year / 100);
-
- /* month */
- rtc_base[0x7ffe] = BIN2BCD(tm.tm_mon);
-
- /* day */
- rtc_base[0x7ffd] = BIN2BCD(tm.tm_mday);
-
- /* hour/min/sec */
- rtc_base[0x7ffb] = BIN2BCD(tm.tm_hour);
- rtc_base[0x7ffa] = BIN2BCD(tm.tm_min);
- rtc_base[0x7ff9] = BIN2BCD(tm.tm_sec);
-
- /* day of week -- not really used, but let's keep it up-to-date */
- rtc_base[0x7ffc] = BIN2BCD(tm.tm_wday + 1);
-
- /* disable writing */
- rtc_base[0x7ff8] = 0x00;
- spin_unlock_irqrestore(&rtc_lock, flags);
-
- return 0;
-}
-
-void __init plat_timer_setup(struct irqaction *irq)
-{
- setup_irq(7, irq);
-}
-
-void momenco_time_init(void)
-{
-#ifdef CONFIG_CPU_SR71000
- mips_hpt_frequency = cpu_clock;
-#elif defined(CONFIG_CPU_RM7000)
- mips_hpt_frequency = cpu_clock / 2;
-#else
-#error Unknown CPU for this board
-#endif
- printk("momenco_time_init cpu_clock=%d\n", cpu_clock);
-
- rtc_mips_get_time = m48t37y_get_time;
- rtc_mips_set_time = m48t37y_set_time;
-}
-
-void __init plat_mem_setup(void)
-{
- unsigned int tmpword;
-
- board_time_init = momenco_time_init;
-
- _machine_restart = momenco_ocelot_restart;
- _machine_halt = momenco_ocelot_halt;
- pm_power_off = momenco_ocelot_power_off;
-
- /*
- * initrd_start = (unsigned long)ocelot_initrd_start;
- * initrd_end = (unsigned long)ocelot_initrd_start + (ulong)ocelot_initrd_size;
- * initrd_below_start_ok = 1;
- */
-
- /* do handoff reconfiguration */
- PMON_v2_setup();
-
- /* shut down ethernet ports, just to be sure our memory doesn't get
- * corrupted by random ethernet traffic.
- */
- MV_WRITE(MV643XX_ETH_TRANSMIT_QUEUE_COMMAND_REG(0), 0xff << 8);
- MV_WRITE(MV643XX_ETH_TRANSMIT_QUEUE_COMMAND_REG(1), 0xff << 8);
- MV_WRITE(MV643XX_ETH_RECEIVE_QUEUE_COMMAND_REG(0), 0xff << 8);
- MV_WRITE(MV643XX_ETH_RECEIVE_QUEUE_COMMAND_REG(1), 0xff << 8);
- do {}
- while (MV_READ(MV643XX_ETH_RECEIVE_QUEUE_COMMAND_REG(0)) & 0xff);
- do {}
- while (MV_READ(MV643XX_ETH_RECEIVE_QUEUE_COMMAND_REG(1)) & 0xff);
- do {}
- while (MV_READ(MV643XX_ETH_TRANSMIT_QUEUE_COMMAND_REG(0)) & 0xff);
- do {}
- while (MV_READ(MV643XX_ETH_TRANSMIT_QUEUE_COMMAND_REG(1)) & 0xff);
- MV_WRITE(MV643XX_ETH_PORT_SERIAL_CONTROL_REG(0),
- MV_READ(MV643XX_ETH_PORT_SERIAL_CONTROL_REG(0)) & ~1);
- MV_WRITE(MV643XX_ETH_PORT_SERIAL_CONTROL_REG(1),
- MV_READ(MV643XX_ETH_PORT_SERIAL_CONTROL_REG(1)) & ~1);
-
- /* Turn off the Bit-Error LED */
- OCELOT_FPGA_WRITE(0x80, CLR);
-
- tmpword = OCELOT_FPGA_READ(BOARDREV);
-#ifdef CONFIG_CPU_SR71000
- if (tmpword < 26)
- printk("Momenco Ocelot-CS: Board Assembly Rev. %c\n",
- 'A'+tmpword);
- else
- printk("Momenco Ocelot-CS: Board Assembly Revision #0x%x\n",
- tmpword);
-#else
- if (tmpword < 26)
- printk("Momenco Ocelot-C: Board Assembly Rev. %c\n",
- 'A'+tmpword);
- else
- printk("Momenco Ocelot-C: Board Assembly Revision #0x%x\n",
- tmpword);
-#endif
-
- tmpword = OCELOT_FPGA_READ(FPGA_REV);
- printk("FPGA Rev: %d.%d\n", tmpword>>4, tmpword&15);
- tmpword = OCELOT_FPGA_READ(RESET_STATUS);
- printk("Reset reason: 0x%x\n", tmpword);
- switch (tmpword) {
- case 0x1:
- printk(" - Power-up reset\n");
- break;
- case 0x2:
- printk(" - Push-button reset\n");
- break;
- case 0x4:
- printk(" - cPCI bus reset\n");
- break;
- case 0x8:
- printk(" - Watchdog reset\n");
- break;
- case 0x10:
- printk(" - Software reset\n");
- break;
- default:
- printk(" - Unknown reset cause\n");
- }
- reset_reason = tmpword;
- OCELOT_FPGA_WRITE(0xff, RESET_STATUS);
-
- tmpword = OCELOT_FPGA_READ(CPCI_ID);
- printk("cPCI ID register: 0x%02x\n", tmpword);
- printk(" - Slot number: %d\n", tmpword & 0x1f);
- printk(" - PCI bus present: %s\n", tmpword & 0x40 ? "yes" : "no");
- printk(" - System Slot: %s\n", tmpword & 0x20 ? "yes" : "no");
-
- tmpword = OCELOT_FPGA_READ(BOARD_STATUS);
- printk("Board Status register: 0x%02x\n", tmpword);
- printk(" - User jumper: %s\n", (tmpword & 0x80)?"installed":"absent");
- printk(" - Boot flash write jumper: %s\n", (tmpword&0x40)?"installed":"absent");
- printk(" - L3 Cache size: %d MiB\n", (1<<((tmpword&12) >> 2))&~1);
- printk(" - SDRAM size: %d MiB\n", 1<<(6+(tmpword&3)));
-
- switch(tmpword &3) {
- case 3:
- /* 512MiB */
- add_memory_region(0x0, 0x200<<20, BOOT_MEM_RAM);
- break;
- case 2:
- /* 256MiB */
- add_memory_region(0x0, 0x100<<20, BOOT_MEM_RAM);
- break;
- case 1:
- /* 128MiB */
- add_memory_region(0x0, 0x80<<20, BOOT_MEM_RAM);
- break;
- case 0:
- /* 1GiB -- needs CONFIG_HIGHMEM */
- add_memory_region(0x0, 0x400<<20, BOOT_MEM_RAM);
- break;
- }
-}
-
-/*
- * This needs to be one of the first initcalls, because no I/O port access
- * can work before this
- */
-static int io_base_ioremap(void)
-{
- void __iomem * io_remap_range = ioremap(0xc0000000UL, 0x10000);
-
- if (!io_remap_range)
- panic("Could not ioremap I/O port range");
-
- set_io_port_base((unsigned long) io_remap_range);
-
- return 0;
-}
-
-module_init(io_base_ioremap);
+++ /dev/null
-/*
- * Copyright 2002 Momentum Computer
- * Author: mdharm@momenco.com
- *
- * arch/mips/momentum/ocelot_c/uart-irq.c
- * Interrupt routines for UARTs. Interrupt numbers are assigned from
- * 80 to 81 (2 interrupt sources).
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/kernel_stat.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include "ocelot_c_fpga.h"
-
-static inline int ls1bit8(unsigned int x)
-{
- int b = 7, s;
-
- s = 4; if (((unsigned char)(x << 4)) == 0) s = 0; b -= s; x <<= s;
- s = 2; if (((unsigned char)(x << 2)) == 0) s = 0; b -= s; x <<= s;
- s = 1; if (((unsigned char)(x << 1)) == 0) s = 0; b -= s;
-
- return b;
-}
-
-/* mask off an interrupt -- 0 is enable, 1 is disable */
-static inline void mask_uart_irq(unsigned int irq)
-{
- uint8_t value;
-
- value = OCELOT_FPGA_READ(UART_INTMASK);
- value |= 1 << (irq - 74);
- OCELOT_FPGA_WRITE(value, UART_INTMASK);
-
- /* read the value back to assure that it's really been written */
- value = OCELOT_FPGA_READ(UART_INTMASK);
-}
-
-/* unmask an interrupt -- 0 is enable, 1 is disable */
-static inline void unmask_uart_irq(unsigned int irq)
-{
- uint8_t value;
-
- value = OCELOT_FPGA_READ(UART_INTMASK);
- value &= ~(1 << (irq - 74));
- OCELOT_FPGA_WRITE(value, UART_INTMASK);
-
- /* read the value back to assure that it's really been written */
- value = OCELOT_FPGA_READ(UART_INTMASK);
-}
-
-/*
- * Interrupt handler for interrupts coming from the FPGA chip.
- */
-void ll_uart_irq(void)
-{
- unsigned int irq_src, irq_mask;
-
- /* read the interrupt status registers */
- irq_src = OCELOT_FPGA_READ(UART_INTSTAT);
- irq_mask = OCELOT_FPGA_READ(UART_INTMASK);
-
- /* mask for just the interrupts we want */
- irq_src &= ~irq_mask;
-
- do_IRQ(ls1bit8(irq_src) + 74);
-}
-
-struct irq_chip uart_irq_type = {
- .name = "UART/FPGA",
- .ack = mask_uart_irq,
- .mask = mask_uart_irq,
- .mask_ack = mask_uart_irq,
- .unmask = unmask_uart_irq,
-};
-
-void uart_irq_init(void)
-{
- set_irq_chip_and_handler(80, &uart_irq_type, handle_level_irq);
- set_irq_chip_and_handler(81, &uart_irq_type, handle_level_irq);
-}
obj-$(CONFIG_MIPS_MALTA) += fixup-malta.o
obj-$(CONFIG_MOMENCO_OCELOT) += fixup-ocelot.o pci-ocelot.o
obj-$(CONFIG_MOMENCO_OCELOT_3) += fixup-ocelot3.o
-obj-$(CONFIG_MOMENCO_OCELOT_C) += fixup-ocelot-c.o pci-ocelot-c.o
obj-$(CONFIG_PMC_YOSEMITE) += fixup-yosemite.o ops-titan.o ops-titan-ht.o \
pci-yosemite.o
obj-$(CONFIG_SGI_IP27) += ops-bridge.o pci-ip27.o
+++ /dev/null
-/*
- * Copyright 2002 Momentum Computer Inc.
- * Author: Matthew Dharm <mdharm@momenco.com>
- *
- * Based on work for the Linux port to the Ocelot board, which is
- * Copyright 2001 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- *
- * arch/mips/momentum/ocelot_g/pci.c
- * Board-specific PCI routines for mv64340 controller.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-
-int __init pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
- int bus = dev->bus->number;
-
- if (bus == 0 && slot == 1)
- return 2; /* PCI-X A */
- if (bus == 1 && slot == 1)
- return 12; /* PCI-X B */
- if (bus == 1 && slot == 2)
- return 4; /* PCI B */
-
-return 0;
- panic("Whooops in pcibios_map_irq");
-}
-
-/* Do platform specific device initialization at pci_enable_device() time */
-int pcibios_plat_dev_init(struct pci_dev *dev)
-{
- return 0;
-}
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2004, 06 by Ralf Baechle (ralf@linux-mips.org)
- */
-
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/mv643xx.h>
-
-#include <linux/init.h>
-
-#include <asm/marvell.h>
-
-/*
- * We assume the address ranges have already been setup appropriately by
- * the firmware. PMON in case of the Ocelot C does that.
- */
-static struct resource mv_pci_io_mem0_resource = {
- .name = "MV64340 PCI0 IO MEM",
- .flags = IORESOURCE_IO
-};
-
-static struct resource mv_pci_mem0_resource = {
- .name = "MV64340 PCI0 MEM",
- .flags = IORESOURCE_MEM
-};
-
-static struct mv_pci_controller mv_bus0_controller = {
- .pcic = {
- .pci_ops = &mv_pci_ops,
- .mem_resource = &mv_pci_mem0_resource,
- .io_resource = &mv_pci_io_mem0_resource,
- },
- .config_addr = MV64340_PCI_0_CONFIG_ADDR,
- .config_vreg = MV64340_PCI_0_CONFIG_DATA_VIRTUAL_REG,
-};
-
-static uint32_t mv_io_base, mv_io_size;
-
-static void mv64340_pci0_init(void)
-{
- uint32_t mem0_base, mem0_size;
- uint32_t io_base, io_size;
-
- io_base = MV_READ(MV64340_PCI_0_IO_BASE_ADDR) << 16;
- io_size = (MV_READ(MV64340_PCI_0_IO_SIZE) + 1) << 16;
- mem0_base = MV_READ(MV64340_PCI_0_MEMORY0_BASE_ADDR) << 16;
- mem0_size = (MV_READ(MV64340_PCI_0_MEMORY0_SIZE) + 1) << 16;
-
- mv_pci_io_mem0_resource.start = 0;
- mv_pci_io_mem0_resource.end = io_size - 1;
- mv_pci_mem0_resource.start = mem0_base;
- mv_pci_mem0_resource.end = mem0_base + mem0_size - 1;
- mv_bus0_controller.pcic.mem_offset = mem0_base;
- mv_bus0_controller.pcic.io_offset = 0;
-
- ioport_resource.end = io_size - 1;
-
- register_pci_controller(&mv_bus0_controller.pcic);
-
- mv_io_base = io_base;
- mv_io_size = io_size;
-}
-
-static struct resource mv_pci_io_mem1_resource = {
- .name = "MV64340 PCI1 IO MEM",
- .flags = IORESOURCE_IO
-};
-
-static struct resource mv_pci_mem1_resource = {
- .name = "MV64340 PCI1 MEM",
- .flags = IORESOURCE_MEM
-};
-
-static struct mv_pci_controller mv_bus1_controller = {
- .pcic = {
- .pci_ops = &mv_pci_ops,
- .mem_resource = &mv_pci_mem1_resource,
- .io_resource = &mv_pci_io_mem1_resource,
- },
- .config_addr = MV64340_PCI_1_CONFIG_ADDR,
- .config_vreg = MV64340_PCI_1_CONFIG_DATA_VIRTUAL_REG,
-};
-
-static __init void mv64340_pci1_init(void)
-{
- uint32_t mem0_base, mem0_size;
- uint32_t io_base, io_size;
-
- io_base = MV_READ(MV64340_PCI_1_IO_BASE_ADDR) << 16;
- io_size = (MV_READ(MV64340_PCI_1_IO_SIZE) + 1) << 16;
- mem0_base = MV_READ(MV64340_PCI_1_MEMORY0_BASE_ADDR) << 16;
- mem0_size = (MV_READ(MV64340_PCI_1_MEMORY0_SIZE) + 1) << 16;
-
- /*
- * Here we assume the I/O window of second bus to be contiguous with
- * the first. A gap is no problem but would waste address space for
- * remapping the port space.
- */
- mv_pci_io_mem1_resource.start = mv_io_size;
- mv_pci_io_mem1_resource.end = mv_io_size + io_size - 1;
- mv_pci_mem1_resource.start = mem0_base;
- mv_pci_mem1_resource.end = mem0_base + mem0_size - 1;
- mv_bus1_controller.pcic.mem_offset = mem0_base;
- mv_bus1_controller.pcic.io_offset = 0;
-
- ioport_resource.end = io_base + io_size -mv_io_base - 1;
-
- register_pci_controller(&mv_bus1_controller.pcic);
-
- mv_io_size = io_base + io_size - mv_io_base;
-}
-
-static __init int __init ocelot_c_pci_init(void)
-{
- unsigned long io_v_base;
- uint32_t enable;
-
- enable = ~MV_READ(MV64340_BASE_ADDR_ENABLE);
-
- /*
- * We require at least one enabled I/O or PCI memory window or we
- * will ignore this PCI bus. We ignore PCI windows 1, 2 and 3.
- */
- if (enable & (0x01 << 9) || enable & (0x01 << 10))
- mv64340_pci0_init();
-
- if (enable & (0x01 << 14) || enable & (0x01 << 15))
- mv64340_pci1_init();
-
- if (mv_io_size) {
- io_v_base = (unsigned long) ioremap(mv_io_base, mv_io_size);
- if (!io_v_base)
- panic("Could not ioremap I/O port range");
-
- set_io_port_base(io_v_base);
- }
-
- return 0;
-}
-
-arch_initcall(ocelot_c_pci_init);
#elif defined(CONFIG_MOMENCO_OCELOT)
0x2f000000,
0xff000000,
-#elif defined(CONFIG_MOMENCO_OCELOT_G) || defined (CONFIG_MOMENCO_OCELOT_C)
+#elif defined(CONFIG_MOMENCO_OCELOT_G)
0xff000000,
##else
#warning Unknown architecture for DiskOnChip. No default probe locations defined
#elif defined(CONFIG_MOMENCO_OCELOT)
0x2f000000,
0xff000000,
-#elif defined(CONFIG_MOMENCO_OCELOT_G) || defined (CONFIG_MOMENCO_OCELOT_C)
+#elif defined(CONFIG_MOMENCO_OCELOT_G)
0xff000000,
#else
#warning Unknown architecture for DiskOnChip. No default probe locations defined
config MV643XX_ETH
tristate "MV-643XX Ethernet support"
- depends on MOMENCO_OCELOT_C || MOMENCO_JAGUAR_ATX || MV64360 || MV64X60 || MOMENCO_OCELOT_3 || (PPC_MULTIPLATFORM && PPC32)
+ depends on MOMENCO_JAGUAR_ATX || MV64360 || MV64X60 || MOMENCO_OCELOT_3 || (PPC_MULTIPLATFORM && PPC32)
select MII
help
This driver supports the gigabit Ethernet on the Marvell MV643XX
#define MACH_GROUP_MOMENCO 12 /* Momentum Boards */
#define MACH_MOMENCO_OCELOT 0
#define MACH_MOMENCO_OCELOT_G 1 /* no more supported (may 2007) */
-#define MACH_MOMENCO_OCELOT_C 2
+#define MACH_MOMENCO_OCELOT_C 2 /* no more supported (jun 2007) */
#define MACH_MOMENCO_JAGUAR_ATX 3 /* no more supported (may 2007) */
#define MACH_MOMENCO_OCELOT_3 4
#define MOMENCO_OCELOT_SERIAL_PORT_DEFNS
#endif
-#ifdef CONFIG_MOMENCO_OCELOT_C
-/* Ordinary NS16552 duart with a 20MHz crystal. */
-#define OCELOT_C_BASE_BAUD ( 20000000 / 16 )
-
-#define OCELOT_C_SERIAL1_IRQ 80
-#define OCELOT_C_SERIAL1_BASE 0xfd000020
-
-#define OCELOT_C_SERIAL2_IRQ 81
-#define OCELOT_C_SERIAL2_BASE 0xfd000000
-
-#define _OCELOT_C_SERIAL_INIT(int, base) \
- { .baud_base = OCELOT_C_BASE_BAUD, \
- .irq = (int), \
- .flags = STD_COM_FLAGS, \
- .iomem_base = (u8 *) base, \
- .iomem_reg_shift = 2, \
- .io_type = SERIAL_IO_MEM \
- }
-#define MOMENCO_OCELOT_C_SERIAL_PORT_DEFNS \
- _OCELOT_C_SERIAL_INIT(OCELOT_C_SERIAL1_IRQ, OCELOT_C_SERIAL1_BASE), \
- _OCELOT_C_SERIAL_INIT(OCELOT_C_SERIAL2_IRQ, OCELOT_C_SERIAL2_BASE)
-#else
-#define MOMENCO_OCELOT_C_SERIAL_PORT_DEFNS
-#endif
-
#ifdef CONFIG_DDB5477
#include <asm/ddb5xxx/ddb5477.h>
#define DDB5477_SERIAL_PORT_DEFNS \
IP32_SERIAL_PORT_DEFNS \
JAZZ_SERIAL_PORT_DEFNS \
STD_SERIAL_PORT_DEFNS \
- MOMENCO_OCELOT_C_SERIAL_PORT_DEFNS \
MOMENCO_OCELOT_SERIAL_PORT_DEFNS \
MOMENCO_OCELOT_3_SERIAL_PORT_DEFNS
#if defined(CONFIG_BASLER_EXCITE) || defined(CONFIG_MOMENCO_JAGUAR_ATX) || \
defined(CONFIG_MIPS_ATLAS) || defined(CONFIG_MIPS_MALTA) || \
defined(CONFIG_MOMENCO_OCELOT) || defined(CONFIG_MOMENCO_OCELOT_3) || \
- defined(CONFIG_MOMENCO_OCELOT_C) || defined(CONFIG_PMC_YOSEMITE) || \
- defined(CONFIG_SGI_IP32) || defined(CONFIG_WR_PPMC)
+ defined(CONFIG_PMC_YOSEMITE) || defined(CONFIG_SGI_IP32) || \
+ defined(CONFIG_WR_PPMC)
#define ICACHE_REFILLS_WORKAROUND_WAR 1
#endif
projects / linux-2.6-omap-h63xx.git / commitdiff