[SERIAL] IOC3: Update 8250 driver bits

Update the support for the 16550 present on most IOC3 configurations to use
the current API.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

diff --git a/drivers/net/ioc3-eth.c b/drivers/net/ioc3-eth.c
index 49e5467bdd7336a34dc9cb5bd5928291c683b408..6a3129bc15a6d6327c5dec32f8e518049e6c5787 100644 (file)
--- a/drivers/net/ioc3-eth.c
+++ b/drivers/net/ioc3-eth.c
@@ -46,10 +46,8 @@
 #include <linux/udp.h>
 
 #ifdef CONFIG_SERIAL_8250
-#include <linux/serial.h>
-#include <asm/serial.h>
-#define IOC3_BAUD (22000000 / (3*16))
-#define IOC3_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
+#include <linux/serial_core.h>
+#include <linux/serial_8250.h>
 #endif
 
 #include <linux/netdevice.h>
@@ -1146,12 +1144,11 @@ static inline int ioc3_is_menet(struct pci_dev *pdev)
  * around ioc3 oddities in this respect.
  *
  * The IOC3 serials use a 22MHz clock rate with an additional divider by 3.
- * (IOC3_BAUD = (22000000 / (3*16)))
  */
 
 static void __devinit ioc3_serial_probe(struct pci_dev *pdev, struct ioc3 *ioc3)
 {
-       struct serial_struct req;
+       struct uart_port port;
 
        /*
         * We need to recognice and treat the fourth MENET serial as it
@@ -1165,20 +1162,25 @@ static void __devinit ioc3_serial_probe(struct pci_dev *pdev, struct ioc3 *ioc3)
        if (ioc3_is_menet(pdev) && PCI_SLOT(pdev->devfn) == 3)
                return;
 
-       /* Register to interrupt zero because we share the interrupt with
-          the serial driver which we don't properly support yet.  */
-       memset(&req, 0, sizeof(req));
-       req.irq             = 0;
-       req.flags           = IOC3_COM_FLAGS;
-       req.io_type         = SERIAL_IO_MEM;
-       req.iomem_reg_shift = 0;
-       req.baud_base       = IOC3_BAUD;
-
-       req.iomem_base      = (unsigned char *) &ioc3->sregs.uarta;
-       register_serial(&req);
-
-       req.iomem_base      = (unsigned char *) &ioc3->sregs.uartb;
-       register_serial(&req);
+       /*
+        * Register to interrupt zero because we share the interrupt with
+        * the serial driver which we don't properly support yet.
+        *
+        * Can't use UPF_IOREMAP as the whole of IOC3 resources have already
+        * been registered.
+        */
+       memset(&port, 0, sizeof(port));
+       port.irq      = 0;
+       port.flags    = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
+       port.iotype   = UPIO_MEM;
+       port.regshift = 0;
+       port.uartclk  = 22000000 / 3;
+
+       port.membase  = (unsigned char *) &ioc3->sregs.uarta;
+       serial8250_register_port(&port);
+
+       port.membase  = (unsigned char *) &ioc3->sregs.uartb;
+       serial8250_register_port(&port);
 }
 #endif