#include <linux/i2c.h>
#include <linux/i2c/twl4030.h>
-#include <linux/i2c/twl4030-gpio.h>
#include <linux/i2c/twl4030-madc.h>
#include <linux/i2c/twl4030-pwrirq.h>
#define TWL4030_MADC_MADC_SIH_CTRL 0x67
#define TWL4030_KEYPAD_KEYP_SIH_CTRL 0x17
-#define TWL4030_SIH_CTRL_COR_MASK (1 << 2)
/**
* struct twl4030_mod_iregs - TWL module IMR/ISR regs to mask/clear at init
/* mapping the module id to slave id and base address */
static struct twl4030mapping twl4030_map[TWL4030_MODULE_LAST + 1] = {
+ /*
+ * NOTE: don't change this table without updating the
+ * <linux/i2c/twl4030.h> defines for TWL4030_MODULE_*
+ * so they continue to match the order in this table.
+ */
+
{ TWL4030_SLAVENUM_NUM0, TWL4030_BASEADD_USB },
+
{ TWL4030_SLAVENUM_NUM1, TWL4030_BASEADD_AUDIO_VOICE },
{ TWL4030_SLAVENUM_NUM1, TWL4030_BASEADD_GPIO },
{ TWL4030_SLAVENUM_NUM1, TWL4030_BASEADD_INTBR },
{ TWL4030_SLAVENUM_NUM1, TWL4030_BASEADD_PIH },
{ TWL4030_SLAVENUM_NUM1, TWL4030_BASEADD_TEST },
+
{ TWL4030_SLAVENUM_NUM2, TWL4030_BASEADD_KEYPAD },
{ TWL4030_SLAVENUM_NUM2, TWL4030_BASEADD_MADC },
{ TWL4030_SLAVENUM_NUM2, TWL4030_BASEADD_INTERRUPTS },
{ TWL4030_SLAVENUM_NUM2, TWL4030_BASEADD_PWM1 },
{ TWL4030_SLAVENUM_NUM2, TWL4030_BASEADD_PWMA },
{ TWL4030_SLAVENUM_NUM2, TWL4030_BASEADD_PWMB },
+
{ TWL4030_SLAVENUM_NUM3, TWL4030_BASEADD_BACKUP },
{ TWL4030_SLAVENUM_NUM3, TWL4030_BASEADD_INT },
{ TWL4030_SLAVENUM_NUM3, TWL4030_BASEADD_PM_MASTER },
/* Are ISRs cleared by reads or writes? */
cor = twl4030_read_cor_bit(tmr.mod_no, tmr.sih_ctrl);
- WARN_ON(cor < 0);
for (j = 0; j < tmr.reg_cnt; j++) {
+++ /dev/null
-/*
- * twl4030-gpio.h - header for TWL4030 GPIO module
- *
- * Copyright (C) 2005-2006, 2008 Texas Instruments, Inc.
- * Copyright (C) 2008 Nokia Corporation
- *
- * Based on tlv320aic23.c:
- * Copyright (c) by Kai Svahn <kai.svahn@nokia.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- */
-
-#ifndef __TWL4030_GPIO_H_
-#define __TWL4030_GPIO_H_
-
-/*
- * GPIO Block Register definitions
- */
-
-#define REG_GPIODATAIN1 0x0
-#define REG_GPIODATAIN2 0x1
-#define REG_GPIODATAIN3 0x2
-#define REG_GPIODATADIR1 0x3
-#define REG_GPIODATADIR2 0x4
-#define REG_GPIODATADIR3 0x5
-#define REG_GPIODATAOUT1 0x6
-#define REG_GPIODATAOUT2 0x7
-#define REG_GPIODATAOUT3 0x8
-#define REG_CLEARGPIODATAOUT1 0x9
-#define REG_CLEARGPIODATAOUT2 0xA
-#define REG_CLEARGPIODATAOUT3 0xB
-#define REG_SETGPIODATAOUT1 0xC
-#define REG_SETGPIODATAOUT2 0xD
-#define REG_SETGPIODATAOUT3 0xE
-#define REG_GPIO_DEBEN1 0xF
-#define REG_GPIO_DEBEN2 0x10
-#define REG_GPIO_DEBEN3 0x11
-#define REG_GPIO_CTRL 0x12
-#define REG_GPIOPUPDCTR1 0x13
-#define REG_GPIOPUPDCTR2 0x14
-#define REG_GPIOPUPDCTR3 0x15
-#define REG_GPIOPUPDCTR4 0x16
-#define REG_GPIOPUPDCTR5 0x17
-#define REG_GPIO_ISR1A 0x19
-#define REG_GPIO_ISR2A 0x1A
-#define REG_GPIO_ISR3A 0x1B
-#define REG_GPIO_IMR1A 0x1C
-#define REG_GPIO_IMR2A 0x1D
-#define REG_GPIO_IMR3A 0x1E
-#define REG_GPIO_ISR1B 0x1F
-#define REG_GPIO_ISR2B 0x20
-#define REG_GPIO_ISR3B 0x21
-#define REG_GPIO_IMR1B 0x22
-#define REG_GPIO_IMR2B 0x23
-#define REG_GPIO_IMR3B 0x24
-#define REG_GPIO_EDR1 0x28
-#define REG_GPIO_EDR2 0x29
-#define REG_GPIO_EDR3 0x2A
-#define REG_GPIO_EDR4 0x2B
-#define REG_GPIO_EDR5 0x2C
-#define REG_GPIO_SIH_CTRL 0x2D
-
-#endif /* End of __TWL4030_GPIO_H */
#ifndef __TWL4030_H_
#define __TWL4030_H_
-/* USB ID */
+/*
+ * Using the twl4030 core we address registers using a pair
+ * { module id, relative register offset }
+ * which that core then maps to the relevant
+ * { i2c slave, absolute register address }
+ *
+ * The module IDs are meaningful only to the twl4030 core code,
+ * which uses them as array indices to look up the first register
+ * address each module uses within a given i2c slave.
+ */
+
+/* Slave 0 (i2c address 0x48) */
#define TWL4030_MODULE_USB 0x00
-/* AUD ID */
+
+/* Slave 1 (i2c address 0x49) */
#define TWL4030_MODULE_AUDIO_VOICE 0x01
#define TWL4030_MODULE_GPIO 0x02
#define TWL4030_MODULE_INTBR 0x03
#define TWL4030_MODULE_PIH 0x04
#define TWL4030_MODULE_TEST 0x05
-/* AUX ID */
+
+/* Slave 2 (i2c address 0x4a) */
#define TWL4030_MODULE_KEYPAD 0x06
#define TWL4030_MODULE_MADC 0x07
#define TWL4030_MODULE_INTERRUPTS 0x08
#define TWL4030_MODULE_PWM1 0x0D
#define TWL4030_MODULE_PWMA 0x0E
#define TWL4030_MODULE_PWMB 0x0F
-/* POWER ID */
+
+/* Slave 3 (i2c address 0x4b) */
#define TWL4030_MODULE_BACKUP 0x10
#define TWL4030_MODULE_INT 0x11
#define TWL4030_MODULE_PM_MASTER 0x12
#define TWL4030_MODULE_RTC 0x14
#define TWL4030_MODULE_SECURED_REG 0x15
+/*
+ * Read and write single 8-bit registers
+ */
+int twl4030_i2c_write_u8(u8 mod_no, u8 val, u8 reg);
+int twl4030_i2c_read_u8(u8 mod_no, u8 *val, u8 reg);
+
+/*
+ * Read and write several 8-bit registers at once.
+ *
+ * IMPORTANT: For twl4030_i2c_write(), allocate num_bytes + 1
+ * for the value, and populate your data starting at offset 1.
+ */
+int twl4030_i2c_write(u8 mod_no, u8 *value, u8 reg, u8 num_bytes);
+int twl4030_i2c_read(u8 mod_no, u8 *value, u8 reg, u8 num_bytes);
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * NOTE: at up to 1024 registers, this is a big chip.
+ *
+ * Avoid putting register declarations in this file, instead of into
+ * a driver-private file, unless some of the registers in a block
+ * need to be shared with other drivers. One example is blocks that
+ * have Secondary IRQ Handler (SIH) registers.
+ */
+
+#define TWL4030_SIH_CTRL_EXCLEN_MASK BIT(0)
+#define TWL4030_SIH_CTRL_PENDDIS_MASK BIT(1)
+#define TWL4030_SIH_CTRL_COR_MASK BIT(2)
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * GPIO Block Register offsets (use TWL4030_MODULE_GPIO)
+ */
+
+#define REG_GPIODATAIN1 0x0
+#define REG_GPIODATAIN2 0x1
+#define REG_GPIODATAIN3 0x2
+#define REG_GPIODATADIR1 0x3
+#define REG_GPIODATADIR2 0x4
+#define REG_GPIODATADIR3 0x5
+#define REG_GPIODATAOUT1 0x6
+#define REG_GPIODATAOUT2 0x7
+#define REG_GPIODATAOUT3 0x8
+#define REG_CLEARGPIODATAOUT1 0x9
+#define REG_CLEARGPIODATAOUT2 0xA
+#define REG_CLEARGPIODATAOUT3 0xB
+#define REG_SETGPIODATAOUT1 0xC
+#define REG_SETGPIODATAOUT2 0xD
+#define REG_SETGPIODATAOUT3 0xE
+#define REG_GPIO_DEBEN1 0xF
+#define REG_GPIO_DEBEN2 0x10
+#define REG_GPIO_DEBEN3 0x11
+#define REG_GPIO_CTRL 0x12
+#define REG_GPIOPUPDCTR1 0x13
+#define REG_GPIOPUPDCTR2 0x14
+#define REG_GPIOPUPDCTR3 0x15
+#define REG_GPIOPUPDCTR4 0x16
+#define REG_GPIOPUPDCTR5 0x17
+#define REG_GPIO_ISR1A 0x19
+#define REG_GPIO_ISR2A 0x1A
+#define REG_GPIO_ISR3A 0x1B
+#define REG_GPIO_IMR1A 0x1C
+#define REG_GPIO_IMR2A 0x1D
+#define REG_GPIO_IMR3A 0x1E
+#define REG_GPIO_ISR1B 0x1F
+#define REG_GPIO_ISR2B 0x20
+#define REG_GPIO_ISR3B 0x21
+#define REG_GPIO_IMR1B 0x22
+#define REG_GPIO_IMR2B 0x23
+#define REG_GPIO_IMR3B 0x24
+#define REG_GPIO_EDR1 0x28
+#define REG_GPIO_EDR2 0x29
+#define REG_GPIO_EDR3 0x2A
+#define REG_GPIO_EDR4 0x2B
+#define REG_GPIO_EDR5 0x2C
+#define REG_GPIO_SIH_CTRL 0x2D
+
+/* Up to 18 signals are available as GPIOs, when their
+ * pins are not assigned to another use (such as ULPI/USB).
+ */
+#define TWL4030_GPIO_MAX 18
+
+/*----------------------------------------------------------------------*/
+
struct twl4030_bci_platform_data {
int *battery_tmp_tbl;
unsigned int tblsize;
/* REVISIT more to come ... _nothing_ should be hard-wired */
};
+/*----------------------------------------------------------------------*/
+
/*
* FIXME completely stop using TWL4030_IRQ_BASE ... instead, pass the
* IRQ data to subsidiary devices using platform device resources.
/* TWL4030 GPIO interrupt definitions */
-#define TWL4030_GPIO_MAX 18
#define TWL4030_GPIO_IRQ_NO(n) (TWL4030_GPIO_IRQ_BASE + (n))
#define TWL4030_GPIO_IS_ENABLE 1
-#define TWL4030_GPIO_PULL_UP 0
-#define TWL4030_GPIO_PULL_DOWN 1
-
-/* Functions to read and write from TWL4030 */
-
-/*
- * IMP NOTE:
- * The base address of the module will be added by the triton driver
- * It is the caller's responsibility to ensure sane values
- */
-int twl4030_i2c_write_u8(u8 mod_no, u8 val, u8 reg);
-int twl4030_i2c_read_u8(u8 mod_no, u8 *val, u8 reg);
-
- /*
- * i2c_write: IMPORTANT - Allocate value num_bytes+1 and valid data starts at
- * Offset 1.
- */
-int twl4030_i2c_write(u8 mod_no, u8 *value, u8 reg, u8 num_bytes);
-int twl4030_i2c_read(u8 mod_no, u8 *value, u8 reg, u8 num_bytes);
/*
* Exported TWL4030 GPIO APIs
projects / linux-2.6-omap-h63xx.git / commitdiff