CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
+
+#
+# Loadable module support
+#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
# CONFIG_KMOD is not set
+
+#
+# Block layer
+#
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
# CONFIG_IP_SCTP is not set
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_SYS_HYPERVISOR is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
# CONFIG_CONNECTOR is not set
# CONFIG_MTD is not set
# CONFIG_PARPORT is not set
# CONFIG_ISCSI_TCP is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_ATA is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
# CONFIG_MD is not set
+
+#
+# Network device support
+#
CONFIG_NETDEVICES=y
# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_PHYLIB is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_AX88796 is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
+#
+# Token Ring devices
+#
+
#
# Wireless LAN
#
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# ISDN subsystem
+#
# CONFIG_ISDN is not set
#
# CONFIG_INPUT_POWERMATE is not set
# CONFIG_INPUT_YEALINK is not set
CONFIG_INPUT_UINPUT=y
+# CONFIG_INPUT_POLLDEV is not set
#
# Hardware I/O ports
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
+
+#
+# IPMI
+#
# CONFIG_IPMI_HANDLER is not set
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_NOWAYOUT=y
# CONFIG_NVRAM is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
-# CONFIG_VFAT_FS is not set
+CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
# CONFIG_NTFS_FS is not set
#
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
-# CONFIG_NLS_CODEPAGE_437 is not set
+CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ASCII is not set
-# CONFIG_NLS_ISO8859_1 is not set
+CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
led-y := leds.o
# Specific board support
-obj-$(CONFIG_MACH_OMAP_H2) += board-h2.o
+obj-$(CONFIG_MACH_OMAP_H2) += board-h2.o board-h2-mmc.o
obj-$(CONFIG_MACH_OMAP_INNOVATOR) += board-innovator.o
obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o
obj-$(CONFIG_MACH_OMAP_PERSEUS2) += board-perseus2.o
obj-$(CONFIG_MACH_OMAP_FSAMPLE) += board-fsample.o
obj-$(CONFIG_MACH_OMAP_OSK) += board-osk.o
-obj-$(CONFIG_MACH_OMAP_H3) += board-h3.o
+obj-$(CONFIG_MACH_OMAP_H3) += board-h3.o board-h3-mmc.o
obj-$(CONFIG_MACH_VOICEBLUE) += board-voiceblue.o
obj-$(CONFIG_MACH_OMAP_PALMTE) += board-palmte.o
obj-$(CONFIG_MACH_OMAP_PALMZ71) += board-palmz71.o
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap1/board-h2-mmc.c
+ *
+ * Copyright (C) 2007 Instituto Nokia de Tecnologia - INdT
+ * Author: Felipe Balbi <felipe.lima@indt.org.br>
+ *
+ * This code is based on linux/arch/arm/mach-omap2/board-n800-mmc.c, which is:
+ * Copyright (C) 2006 Nokia Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <asm/arch/mmc.h>
+#include <asm/arch/gpio.h>
+
+#ifdef CONFIG_MMC_OMAP
+static int slot_cover_open;
+static struct device *mmc_device;
+
+static int h2_mmc_set_power(struct device *dev, int slot, int power_on,
+ int vdd)
+{
+#ifdef CONFIG_MMC_DEBUG
+ dev_dbg(dev, "Set slot %d power: %s (vdd %d)\n", slot + 1,
+ power_on ? "on" : "off", vdd);
+#endif
+ if (slot != 0) {
+ dev_err(dev, "No such slot %d\n", slot + 1);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int h2_mmc_set_bus_mode(struct device *dev, int slot, int bus_mode)
+{
+#ifdef CONFIG_MMC_DEBUG
+ dev_dbg(dev, "Set slot %d bus_mode %s\n", slot + 1,
+ bus_mode == MMC_BUSMODE_OPENDRAIN ? "open-drain" : "push-pull");
+#endif
+ if (slot != 0) {
+ dev_err(dev, "No such slot %d\n", slot + 1);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int h2_mmc_get_cover_state(struct device *dev, int slot)
+{
+ BUG_ON(slot != 0);
+
+ return slot_cover_open;
+}
+
+void h2_mmc_slot_cover_handler(void *arg, int state)
+{
+ if (mmc_device == NULL)
+ return;
+
+ slot_cover_open = state;
+ omap_mmc_notify_cover_event(mmc_device, 0, state);
+}
+
+static int h2_mmc_late_init(struct device *dev)
+{
+ int ret = 0;
+
+ mmc_device = dev;
+
+ return ret;
+}
+
+static void h2_mmc_cleanup(struct device *dev)
+{
+}
+
+static struct omap_mmc_platform_data h2_mmc_data = {
+ .nr_slots = 1,
+ .switch_slot = NULL,
+ .init = h2_mmc_late_init,
+ .cleanup = h2_mmc_cleanup,
+ .slots[0] = {
+ .set_power = h2_mmc_set_power,
+ .set_bus_mode = h2_mmc_set_bus_mode,
+ .get_ro = NULL,
+ .get_cover_state = h2_mmc_get_cover_state,
+ .ocr_mask = MMC_VDD_28_29 | MMC_VDD_30_31 |
+ MMC_VDD_32_33 | MMC_VDD_33_34,
+ .name = "mmcblk",
+ },
+};
+
+void __init h2_mmc_init(void)
+{
+ omap_set_mmc_info(1, &h2_mmc_data);
+}
+
+#else
+
+void __init h2_mmc_init(void)
+{
+}
+
+void h2_mmc_slot_cover_handler(void *arg, int state)
+{
+}
+#endif
};
static struct omap_mmc_config h2_mmc_config __initdata = {
- .mmc [0] = {
- .enabled = 1,
+ .mmc[0] = {
+ .enabled = 1,
.wire4 = 1,
- .wp_pin = OMAP_MPUIO(3),
- .power_pin = -1, /* tps65010 gpio3 */
- .switch_pin = OMAP_MPUIO(1),
},
};
+extern struct omap_mmc_platform_data h2_mmc_data;
+
static struct omap_uart_config h2_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
omap_board_config = h2_config;
omap_board_config_size = ARRAY_SIZE(h2_config);
omap_serial_init();
+ h2_mmc_init();
/* irq for tps65010 chip */
omap_cfg_reg(W4_GPIO58);
--- /dev/null
+/*
+ * linux/arch/arm/mach-omap1/board-h3-mmc.c
+ *
+ * Copyright (C) 2007 Instituto Nokia de Tecnologia - INdT
+ * Author: Felipe Balbi <felipe.lima@indt.org.br>
+ *
+ * This code is based on linux/arch/arm/mach-omap2/board-n800-mmc.c, which is:
+ * Copyright (C) 2006 Nokia Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <asm/arch/mmc.h>
+#include <asm/arch/gpio.h>
+
+#ifdef CONFIG_MMC_OMAP
+static int slot_cover_open;
+static struct device *mmc_device;
+
+static int h3_mmc_set_power(struct device *dev, int slot, int power_on,
+ int vdd)
+{
+#ifdef CONFIG_MMC_DEBUG
+ dev_dbg(dev, "Set slot %d power: %s (vdd %d)\n", slot + 1,
+ power_on ? "on" : "off", vdd);
+#endif
+ if (slot != 0) {
+ dev_err(dev, "No such slot %d\n", slot + 1);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int h3_mmc_set_bus_mode(struct device *dev, int slot, int bus_mode)
+{
+ int ret = 0;
+
+#ifdef CONFIG_MMC_DEBUG
+ dev_dbg(dev, "Set slot %d bus_mode %s\n", slot + 1,
+ bus_mode == MMC_BUSMODE_OPENDRAIN ? "open-drain" : "push-pull");
+#endif
+ if (slot != 0) {
+ dev_err(dev, "No such slot %d\n", slot + 1);
+ return -ENODEV;
+ }
+
+ /* Treated on upper level */
+
+ return bus_mode;
+}
+
+static int h3_mmc_get_cover_state(struct device *dev, int slot)
+{
+ BUG_ON(slot != 0);
+
+ return slot_cover_open;
+}
+
+void h3_mmc_slot_cover_handler(void *arg, int state)
+{
+ if (mmc_device == NULL)
+ return;
+
+ slot_cover_open = state;
+ omap_mmc_notify_cover_event(mmc_device, 0, state);
+}
+
+static int h3_mmc_late_init(struct device *dev)
+{
+ int ret = 0;
+
+ mmc_device = dev;
+
+ return ret;
+}
+
+static void h3_mmc_cleanup(struct device *dev)
+{
+}
+
+static struct omap_mmc_platform_data h3_mmc_data = {
+ .nr_slots = 1,
+ .switch_slot = NULL,
+ .init = h3_mmc_late_init,
+ .cleanup = h3_mmc_cleanup,
+ .slots[0] = {
+ .set_power = h3_mmc_set_power,
+ .set_bus_mode = h3_mmc_set_bus_mode,
+ .get_ro = NULL,
+ .get_cover_state = h3_mmc_get_cover_state,
+ .ocr_mask = MMC_VDD_28_29 | MMC_VDD_30_31 |
+ MMC_VDD_32_33 | MMC_VDD_33_34,
+ .name = "mmcblk",
+ },
+};
+
+void __init h3_mmc_init(void)
+{
+ omap_set_mmc_info(1, &h3_mmc_data);
+}
+
+#else
+
+void __init h3_mmc_init(void)
+{
+}
+
+void h3_mmc_slot_cover_handler(void *arg, int state)
+{
+}
+#endif
static struct omap_mmc_config h3_mmc_config __initdata = {
.mmc[0] = {
- .enabled = 1,
- .power_pin = -1, /* tps65010 GPIO4 */
- .switch_pin = OMAP_MPUIO(1),
- },
+ .enabled = 1,
+ .wire4 = 1,
+ },
};
+extern struct omap_mmc_platform_data h3_mmc_data;
+
static struct omap_uart_config h3_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
*/
};
+static struct omap_gpio_switch h3_gpio_switches[] __initdata = {
+ {
+ .name = "mmc_slot",
+ .gpio = OMAP_MPUIO(1),
+ .type = OMAP_GPIO_SWITCH_TYPE_COVER,
+ .debounce_rising = 100,
+ .debounce_falling = 0,
+ .notify = h3_mmc_slot_cover_handler,
+ .notify_data = NULL,
+ },
+};
+
#define H3_NAND_RB_GPIO_PIN 10
static int nand_dev_ready(struct omap_nand_platform_data *data)
omap_board_config = h3_config;
omap_board_config_size = ARRAY_SIZE(h3_config);
omap_serial_init();
+ h3_mmc_init();
/* FIXME setup irq for tps65013 chip */
i2c_register_board_info(1, h3_i2c_board_info,
#ifndef __ASM_ARCH_OMAP_APOLLON_H
#define __ASM_ARCH_OMAP_APOLLON_H
+extern void apollon_mmc_init(void);
+
/* Placeholder for APOLLON specific defines */
#define APOLLON_ETHR_GPIO_IRQ 74
/* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */
#define OMAP1610_ETHR_START 0x04000300
+extern void h2_mmc_init(void);
+extern void h2_mmc_slot_cover_handler(void *arg, int state);
+
#endif /* __ASM_ARCH_OMAP_H2_H */
#define NR_IRQS (MAXIRQNUM + 1)
+extern void __init h3_mmc_init(void);
+extern void h3_mmc_slot_cover_handler(void *arg, int state);
#endif /* __ASM_ARCH_OMAP_H3_H */
projects / linux-2.6-omap-h63xx.git / commitdiff