]> pilppa.com Git - linux-2.6-omap-h63xx.git/commitdiff
USB Serial Keyspan: add support for USA-49WG & USA-28XG
authorLucy McCoy <lucy@keyspan.com>
Fri, 18 May 2007 19:10:41 +0000 (12:10 -0700)
committerGreg Kroah-Hartman <gregkh@suse.de>
Thu, 12 Jul 2007 23:29:45 +0000 (16:29 -0700)
Add support for Keyspan adapters: USA-49WG and USA-28XG

Signed-off-by: Lucy P. McCoy <lucy@keyspan.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/serial/keyspan.c
drivers/usb/serial/keyspan.h
drivers/usb/serial/keyspan_usa67msg.h [new file with mode: 0644]

index e6966f12ed5aacdace21a8d14fe79d649f09e406..fa91ddee24584dee6c6db125c6b9d26108f330c8 100644 (file)
@@ -115,12 +115,13 @@ static int debug;
 /*
  * Version Information
  */
-#define DRIVER_VERSION "v1.1.4"
+#define DRIVER_VERSION "v1.1.5"
 #define DRIVER_AUTHOR "Hugh Blemings <hugh@misc.nu"
 #define DRIVER_DESC "Keyspan USB to Serial Converter Driver"
 
 #define INSTAT_BUFLEN  32
 #define GLOCONT_BUFLEN 64
+#define INDAT49W_BUFLEN        512
 
        /* Per device and per port private data */
 struct keyspan_serial_private {
@@ -129,9 +130,15 @@ struct keyspan_serial_private {
        struct urb      *instat_urb;
        char            instat_buf[INSTAT_BUFLEN];
 
+       /* added to support 49wg, where data from all 4 ports comes in on 1 EP */
+       /* and high-speed supported */
+       struct urb      *indat_urb;
+       char            indat_buf[INDAT49W_BUFLEN];
+
        /* XXX this one probably will need a lock */
        struct urb      *glocont_urb;
        char            glocont_buf[GLOCONT_BUFLEN];
+       char            ctrl_buf[8];                    // for EP0 control message
 };
 
 struct keyspan_port_private {
@@ -179,12 +186,13 @@ struct keyspan_port_private {
 
        
 /* Include Keyspan message headers.  All current Keyspan Adapters
-   make use of one of four message formats which are referred
-   to as USA-26, USA-28 and USA-49, USA-90 by Keyspan and within this driver. */
+   make use of one of five message formats which are referred
+   to as USA-26, USA-28, USA-49, USA-90, USA-67 by Keyspan and within this driver. */
 #include "keyspan_usa26msg.h"
 #include "keyspan_usa28msg.h"
 #include "keyspan_usa49msg.h"
 #include "keyspan_usa90msg.h"
+#include "keyspan_usa67msg.h"
        
 
 /* Functions used by new usb-serial code. */
@@ -850,13 +858,89 @@ static void       usa49_indat_callback(struct urb *urb)
                }
 }
 
+static void usa49wg_indat_callback(struct urb *urb)
+{
+       int                     i, len, x, err;
+       struct usb_serial       *serial;
+       struct usb_serial_port  *port;
+       struct tty_struct       *tty;
+       unsigned char           *data = urb->transfer_buffer;
+
+       dbg ("%s", __FUNCTION__);
+
+       serial = urb->context;
+
+       if (urb->status) {
+               dbg("%s - nonzero status: %x", __FUNCTION__, urb->status);
+               return;
+       }
+
+       /* inbound data is in the form P#, len, status, data */
+       i = 0;
+       len = 0;
+
+       if (urb->actual_length) {
+               while (i < urb->actual_length) {
+
+                       /* Check port number from message*/
+                       if (data[i] >= serial->num_ports) {
+                               dbg ("%s - Unexpected port number %d",
+                                       __FUNCTION__, data[i]);
+                               return;
+                       }
+                       port = serial->port[data[i++]];
+                       tty = port->tty;
+                       len = data[i++];
+
+                       /* 0x80 bit is error flag */
+                       if ((data[i] & 0x80) == 0) {
+                               /* no error on any byte */
+                               i++;
+                               for (x = 1; x < len ; ++x)
+                                       if (port->open_count)
+                                               tty_insert_flip_char(tty,
+                                                               data[i++], 0);
+                                       else
+                                               i++;
+                       } else {
+                               /*
+                                * some bytes had errors, every byte has status
+                                */
+                               for (x = 0; x + 1 < len; x += 2) {
+                                       int stat = data[i], flag = 0;
+                                       if (stat & RXERROR_OVERRUN)
+                                               flag |= TTY_OVERRUN;
+                                       if (stat & RXERROR_FRAMING)
+                                               flag |= TTY_FRAME;
+                                       if (stat & RXERROR_PARITY)
+                                               flag |= TTY_PARITY;
+                                       /* XXX should handle break (0x10) */
+                                       if (port->open_count)
+                                               tty_insert_flip_char(tty,
+                                                       data[i+1], flag);
+                                       i += 2;
+                               }
+                       }
+                       if (port->open_count)
+                               tty_flip_buffer_push(tty);
+               }
+       }
+
+       /* Resubmit urb so we continue receiving */
+       urb->dev = serial->dev;
+
+       err = usb_submit_urb(urb, GFP_ATOMIC);
+       if (err != 0)
+               dbg("%s - resubmit read urb failed. (%d)", __FUNCTION__, err);
+}
+
 /* not used, usa-49 doesn't have per-port control endpoints */
-static void    usa49_outcont_callback(struct urb *urb)
+static void usa49_outcont_callback(struct urb *urb)
 {
        dbg ("%s", __FUNCTION__);
 }
 
-static void    usa90_indat_callback(struct urb *urb)
+static void usa90_indat_callback(struct urb *urb)
 {
        int                     i, err;
        int                     endpoint;
@@ -869,7 +953,6 @@ static void usa90_indat_callback(struct urb *urb)
 
        endpoint = usb_pipeendpoint(urb->pipe);
 
-
        if (urb->status) {
                dbg("%s - nonzero status: %x on endpoint %d.",
                    __FUNCTION__, urb->status, endpoint);
@@ -995,6 +1078,87 @@ static void       usa90_outcont_callback(struct urb *urb)
        }
 }
 
+/* Status messages from the 28xg */
+static void    usa67_instat_callback(struct urb *urb)
+{
+       int                                     err;
+       unsigned char                           *data = urb->transfer_buffer;
+       struct keyspan_usa67_portStatusMessage  *msg;
+       struct usb_serial                       *serial;
+       struct usb_serial_port                  *port;
+       struct keyspan_port_private             *p_priv;
+       int old_dcd_state;
+
+       dbg ("%s", __FUNCTION__);
+
+       serial = urb->context;
+
+       if (urb->status) {
+               dbg("%s - nonzero status: %x", __FUNCTION__, urb->status);
+               return;
+       }
+
+       if (urb->actual_length != sizeof(struct keyspan_usa67_portStatusMessage)) {
+               dbg("%s - bad length %d", __FUNCTION__, urb->actual_length);
+               return;
+       }
+
+
+       /* Now do something useful with the data */
+       msg = (struct keyspan_usa67_portStatusMessage *)data;
+
+       /* Check port number from message and retrieve private data */
+       if (msg->port >= serial->num_ports) {
+               dbg ("%s - Unexpected port number %d", __FUNCTION__, msg->port);
+               return;
+       }
+
+       port = serial->port[msg->port];
+       p_priv = usb_get_serial_port_data(port);
+
+       /* Update handshaking pin state information */
+       old_dcd_state = p_priv->dcd_state;
+       p_priv->cts_state = ((msg->hskia_cts) ? 1 : 0);
+       p_priv->dcd_state = ((msg->gpia_dcd) ? 1 : 0);
+
+       if (port->tty && !C_CLOCAL(port->tty)
+           && old_dcd_state != p_priv->dcd_state) {
+               if (old_dcd_state)
+                       tty_hangup(port->tty);
+               /*  else */
+               /*      wake_up_interruptible(&p_priv->open_wait); */
+       }
+
+       /* Resubmit urb so we continue receiving */
+       urb->dev = serial->dev;
+       err = usb_submit_urb(urb, GFP_ATOMIC);
+       if (err != 0)
+               dbg("%s - resubmit read urb failed. (%d)", __FUNCTION__, err);
+}
+
+static void usa67_glocont_callback(struct urb *urb)
+{
+       struct usb_serial *serial;
+       struct usb_serial_port *port;
+       struct keyspan_port_private *p_priv;
+       int i;
+
+       dbg ("%s", __FUNCTION__);
+
+       serial = urb->context;
+       for (i = 0; i < serial->num_ports; ++i) {
+               port = serial->port[i];
+               p_priv = usb_get_serial_port_data(port);
+
+               if (p_priv->resend_cont) {
+                       dbg ("%s - sending setup", __FUNCTION__);
+                       keyspan_usa67_send_setup(serial, port,
+                                               p_priv->resend_cont - 1);
+                       break;
+               }
+       }
+}
+
 static int keyspan_write_room (struct usb_serial_port *port)
 {
        struct keyspan_port_private     *p_priv;
@@ -1311,6 +1475,11 @@ static struct urb *keyspan_setup_urb (struct usb_serial *serial, int endpoint,
                return NULL;
        }
 
+       if (endpoint == 0) {
+               /* control EP filled in when used */
+               return urb;
+       }
+
        ep_desc = find_ep(serial, endpoint);
        if (!ep_desc) {
                /* leak the urb, something's wrong and the callers don't care */
@@ -1380,6 +1549,14 @@ static struct callbacks {
                .outdat_callback =      usa2x_outdat_callback,
                .inack_callback =       usa28_inack_callback,
                .outcont_callback =     usa90_outcont_callback,
+       }, {
+               /* msg_usa67 callbacks */
+               .instat_callback =      usa67_instat_callback,
+               .glocont_callback =     usa67_glocont_callback,
+               .indat_callback =       usa26_indat_callback,
+               .outdat_callback =      usa2x_outdat_callback,
+               .inack_callback =       usa26_inack_callback,
+               .outcont_callback =     usa26_outcont_callback,
        }
 };
 
@@ -1410,6 +1587,11 @@ static void keyspan_setup_urbs(struct usb_serial *serial)
                 serial, s_priv->instat_buf, INSTAT_BUFLEN,
                 cback->instat_callback);
 
+       s_priv->indat_urb = keyspan_setup_urb
+               (serial, d_details->indat_endpoint, USB_DIR_IN,
+                serial, s_priv->indat_buf, INDAT49W_BUFLEN,
+                usa49wg_indat_callback);
+
        s_priv->glocont_urb = keyspan_setup_urb
                (serial, d_details->glocont_endpoint, USB_DIR_OUT,
                 serial, s_priv->glocont_buf, GLOCONT_BUFLEN,
@@ -1685,8 +1867,8 @@ static int keyspan_usa26_send_setup(struct usb_serial *serial,
        }
 
        /* Save reset port val for resend.
-       Don't overwrite resend for close condition. */
-       if (p_priv->resend_cont != 3)
+          Don't overwrite resend for open/close condition. */
+       if ((reset_port + 1) > p_priv->resend_cont)
                p_priv->resend_cont = reset_port + 1;
        if (this_urb->status == -EINPROGRESS) {
                /*  dbg ("%s - already writing", __FUNCTION__); */
@@ -1836,8 +2018,8 @@ static int keyspan_usa28_send_setup(struct usb_serial *serial,
        }
 
        /* Save reset port val for resend.
-          Don't overwrite resend for close condition. */
-       if (p_priv->resend_cont != 3)
+          Don't overwrite resend for open/close condition. */
+       if ((reset_port + 1) > p_priv->resend_cont)
                p_priv->resend_cont = reset_port + 1;
        if (this_urb->status == -EINPROGRESS) {
                dbg ("%s already writing", __FUNCTION__);
@@ -1940,11 +2122,11 @@ static int keyspan_usa49_send_setup(struct usb_serial *serial,
                                    struct usb_serial_port *port,
                                    int reset_port)
 {
-       struct keyspan_usa49_portControlMessage msg;            
+       struct keyspan_usa49_portControlMessage msg;
+       struct usb_ctrlrequest                  *dr = NULL;
        struct keyspan_serial_private           *s_priv;
        struct keyspan_port_private             *p_priv;
        const struct keyspan_device_details     *d_details;
-       int                                     glocont_urb;
        struct urb                              *this_urb;
        int                                     err, device_port;
 
@@ -1954,10 +2136,9 @@ static int keyspan_usa49_send_setup(struct usb_serial *serial,
        p_priv = usb_get_serial_port_data(port);
        d_details = s_priv->device_details;
 
-       glocont_urb = d_details->glocont_endpoint;
        this_urb = s_priv->glocont_urb;
 
-               /* Work out which port within the device is being setup */
+       /* Work out which port within the device is being setup */
        device_port = port->number - port->serial->minor;
 
        dbg("%s - endpoint %d port %d (%d)",__FUNCTION__, usb_pipeendpoint(this_urb->pipe), port->number, device_port);
@@ -1969,9 +2150,10 @@ static int keyspan_usa49_send_setup(struct usb_serial *serial,
        }
 
        /* Save reset port val for resend.
-          Don't overwrite resend for close condition. */
-       if (p_priv->resend_cont != 3)
+          Don't overwrite resend for open/close condition. */
+       if ((reset_port + 1) > p_priv->resend_cont)
                p_priv->resend_cont = reset_port + 1;
+
        if (this_urb->status == -EINPROGRESS) {
                /*  dbg ("%s - already writing", __FUNCTION__); */
                mdelay(5);
@@ -2083,20 +2265,39 @@ static int keyspan_usa49_send_setup(struct usb_serial *serial,
        msg.dtr = p_priv->dtr_state;
                
        p_priv->resend_cont = 0;
-       memcpy (this_urb->transfer_buffer, &msg, sizeof(msg));
+
+       /* if the device is a 49wg, we send control message on usb control EP 0 */
+
+       if (d_details->product_id == keyspan_usa49wg_product_id) {
+               dr = (void *)(s_priv->ctrl_buf);
+               dr->bRequestType = USB_TYPE_VENDOR | USB_DIR_OUT;
+               dr->bRequest = 0xB0;    /* 49wg control message */;
+               dr->wValue = 0;
+               dr->wIndex = 0;
+               dr->wLength = cpu_to_le16(sizeof(msg));
+
+               memcpy (s_priv->glocont_buf, &msg, sizeof(msg));
+
+               usb_fill_control_urb(this_urb, serial->dev, usb_sndctrlpipe(serial->dev, 0),
+                            (unsigned char *)dr, s_priv->glocont_buf, sizeof(msg),
+                            usa49_glocont_callback, serial);
+
+       } else {
+               memcpy(this_urb->transfer_buffer, &msg, sizeof(msg));
        
-       /* send the data out the device on control endpoint */
-       this_urb->transfer_buffer_length = sizeof(msg);
+               /* send the data out the device on control endpoint */
+               this_urb->transfer_buffer_length = sizeof(msg);
 
-       this_urb->dev = serial->dev;
+               this_urb->dev = serial->dev;
+       }
        if ((err = usb_submit_urb(this_urb, GFP_ATOMIC)) != 0) {
                dbg("%s - usb_submit_urb(setup) failed (%d)", __FUNCTION__, err);
        }
 #if 0
        else {
                dbg("%s - usb_submit_urb(%d) OK %d bytes (end %d)", __FUNCTION__,
-                   outcont_urb, this_urb->transfer_buffer_length,
-                   usb_pipeendpoint(this_urb->pipe));
+                          outcont_urb, this_urb->transfer_buffer_length,
+                          usb_pipeendpoint(this_urb->pipe));
        }
 #endif
 
@@ -2241,6 +2442,154 @@ static int keyspan_usa90_send_setup(struct usb_serial *serial,
        return (0);
 }
 
+static int keyspan_usa67_send_setup(struct usb_serial *serial,
+                                   struct usb_serial_port *port,
+                                   int reset_port)
+{
+       struct keyspan_usa67_portControlMessage msg;
+       struct keyspan_serial_private           *s_priv;
+       struct keyspan_port_private             *p_priv;
+       const struct keyspan_device_details     *d_details;
+       struct urb                              *this_urb;
+       int                                     err, device_port;
+
+       dbg ("%s", __FUNCTION__);
+
+       s_priv = usb_get_serial_data(serial);
+       p_priv = usb_get_serial_port_data(port);
+       d_details = s_priv->device_details;
+
+       this_urb = s_priv->glocont_urb;
+
+       /* Work out which port within the device is being setup */
+       device_port = port->number - port->serial->minor;
+
+       /* Make sure we have an urb then send the message */
+       if (this_urb == NULL) {
+               dbg("%s - oops no urb for port %d.", __FUNCTION__,
+                       port->number);
+               return -1;
+       }
+
+       /* Save reset port val for resend.
+          Don't overwrite resend for open/close condition. */
+       if ((reset_port + 1) > p_priv->resend_cont)
+               p_priv->resend_cont = reset_port + 1;
+       if (this_urb->status == -EINPROGRESS) {
+               /*  dbg ("%s - already writing", __FUNCTION__); */
+               mdelay(5);
+               return(-1);
+       }
+
+       memset(&msg, 0, sizeof(struct keyspan_usa67_portControlMessage));
+
+       msg.port = device_port;
+
+       /* Only set baud rate if it's changed */
+       if (p_priv->old_baud != p_priv->baud) {
+               p_priv->old_baud = p_priv->baud;
+               msg.setClocking = 0xff;
+               if (d_details->calculate_baud_rate
+                   (p_priv->baud, d_details->baudclk, &msg.baudHi,
+                    &msg.baudLo, &msg.prescaler, device_port) == KEYSPAN_INVALID_BAUD_RATE ) {
+                       dbg("%s - Invalid baud rate %d requested, using 9600.", __FUNCTION__,
+                           p_priv->baud);
+                       msg.baudLo = 0;
+                       msg.baudHi = 125;       /* Values for 9600 baud */
+                       msg.prescaler = 10;
+               }
+               msg.setPrescaler = 0xff;
+       }
+
+       msg.lcr = (p_priv->cflag & CSTOPB) ? STOPBITS_678_2 : STOPBITS_5678_1;
+       switch (p_priv->cflag & CSIZE) {
+       case CS5:
+               msg.lcr |= USA_DATABITS_5;
+               break;
+       case CS6:
+               msg.lcr |= USA_DATABITS_6;
+               break;
+       case CS7:
+               msg.lcr |= USA_DATABITS_7;
+               break;
+       case CS8:
+               msg.lcr |= USA_DATABITS_8;
+               break;
+       }
+       if (p_priv->cflag & PARENB) {
+               /* note USA_PARITY_NONE == 0 */
+               msg.lcr |= (p_priv->cflag & PARODD)?
+                       USA_PARITY_ODD: USA_PARITY_EVEN;
+       }
+       msg.setLcr = 0xff;
+
+       msg.ctsFlowControl = (p_priv->flow_control == flow_cts);
+       msg.xonFlowControl = 0;
+       msg.setFlowControl = 0xff;
+       msg.forwardingLength = 16;
+       msg.xonChar = 17;
+       msg.xoffChar = 19;
+
+       if (reset_port == 1) {
+               /* Opening port */
+               msg._txOn = 1;
+               msg._txOff = 0;
+               msg.txFlush = 0;
+               msg.txBreak = 0;
+               msg.rxOn = 1;
+               msg.rxOff = 0;
+               msg.rxFlush = 1;
+               msg.rxForward = 0;
+               msg.returnStatus = 0;
+               msg.resetDataToggle = 0xff;
+       } else if (reset_port == 2) {
+               /* Closing port */
+               msg._txOn = 0;
+               msg._txOff = 1;
+               msg.txFlush = 0;
+               msg.txBreak = 0;
+               msg.rxOn = 0;
+               msg.rxOff = 1;
+               msg.rxFlush = 1;
+               msg.rxForward = 0;
+               msg.returnStatus = 0;
+               msg.resetDataToggle = 0;
+       } else {
+               /* Sending intermediate configs */
+               msg._txOn = (! p_priv->break_on);
+               msg._txOff = 0;
+               msg.txFlush = 0;
+               msg.txBreak = (p_priv->break_on);
+               msg.rxOn = 0;
+               msg.rxOff = 0;
+               msg.rxFlush = 0;
+               msg.rxForward = 0;
+               msg.returnStatus = 0;
+               msg.resetDataToggle = 0x0;
+       }
+
+       /* Do handshaking outputs */
+       msg.setTxTriState_setRts = 0xff;
+       msg.txTriState_rts = p_priv->rts_state;
+
+       msg.setHskoa_setDtr = 0xff;
+       msg.hskoa_dtr = p_priv->dtr_state;
+
+       p_priv->resend_cont = 0;
+
+       memcpy(this_urb->transfer_buffer, &msg, sizeof(msg));
+
+       /* send the data out the device on control endpoint */
+       this_urb->transfer_buffer_length = sizeof(msg);
+       this_urb->dev = serial->dev;
+
+       err = usb_submit_urb(this_urb, GFP_ATOMIC);
+       if (err != 0)
+               dbg("%s - usb_submit_urb(setup) failed (%d)", __FUNCTION__,
+                               err);
+       return (0);
+}
+
 static void keyspan_send_setup(struct usb_serial_port *port, int reset_port)
 {
        struct usb_serial *serial = port->serial;
@@ -2265,6 +2614,9 @@ static void keyspan_send_setup(struct usb_serial_port *port, int reset_port)
        case msg_usa90:
                keyspan_usa90_send_setup(serial, port, reset_port);
                break;
+       case msg_usa67:
+               keyspan_usa67_send_setup(serial, port, reset_port);
+               break;
        }
 }
 
@@ -2313,9 +2665,19 @@ static int keyspan_startup (struct usb_serial *serial)
 
        keyspan_setup_urbs(serial);
 
-       s_priv->instat_urb->dev = serial->dev;
-       if ((err = usb_submit_urb(s_priv->instat_urb, GFP_KERNEL)) != 0) {
-               dbg("%s - submit instat urb failed %d", __FUNCTION__, err);
+       if (s_priv->instat_urb != NULL) {
+               s_priv->instat_urb->dev = serial->dev;
+               err = usb_submit_urb(s_priv->instat_urb, GFP_KERNEL);
+               if (err != 0)
+                       dbg("%s - submit instat urb failed %d", __FUNCTION__,
+                               err);
+       }
+       if (s_priv->indat_urb != NULL) {
+               s_priv->indat_urb->dev = serial->dev;
+               err = usb_submit_urb(s_priv->indat_urb, GFP_KERNEL);
+               if (err != 0)
+                       dbg("%s - submit indat urb failed %d", __FUNCTION__,
+                               err);
        }
                        
        return (0);
@@ -2335,6 +2697,7 @@ static void keyspan_shutdown (struct usb_serial *serial)
        /* Stop reading/writing urbs */
        stop_urb(s_priv->instat_urb);
        stop_urb(s_priv->glocont_urb);
+       stop_urb(s_priv->indat_urb);
        for (i = 0; i < serial->num_ports; ++i) {
                port = serial->port[i];
                p_priv = usb_get_serial_port_data(port);
@@ -2348,6 +2711,7 @@ static void keyspan_shutdown (struct usb_serial *serial)
 
        /* Now free them */
        usb_free_urb(s_priv->instat_urb);
+       usb_free_urb(s_priv->indat_urb);
        usb_free_urb(s_priv->glocont_urb);
        for (i = 0; i < serial->num_ports; ++i) {
                port = serial->port[i];
index c6830cbdc6df32740b43901090a826f361a06aae..8a0d17401529986b077da08a15a292d1e2de14af 100644 (file)
@@ -99,6 +99,10 @@ static int  keyspan_usa90_send_setup (struct usb_serial *serial,
                                         struct usb_serial_port *port,
                                         int reset_port);
 
+static int  keyspan_usa67_send_setup   (struct usb_serial *serial,
+                                        struct usb_serial_port *port,
+                                        int reset_port);
+
 /* Struct used for firmware - increased size of data section
    to allow Keyspan's 'C' firmware struct to be used unmodified */
 struct ezusb_hex_record {
@@ -229,15 +233,17 @@ struct ezusb_hex_record {
 #define        keyspan_usa28_product_id                0x010f
 #define        keyspan_usa28x_product_id               0x0110
 #define        keyspan_usa28xa_product_id              0x0115
+#define        keyspan_usa28xb_product_id              0x0110
+#define        keyspan_usa28xg_product_id              0x0135
 #define        keyspan_usa49w_product_id               0x010a
 #define        keyspan_usa49wlc_product_id             0x012a
-
+#define        keyspan_usa49wg_product_id              0x0131
 
 struct keyspan_device_details {
        /* product ID value */
        int     product_id;
 
-       enum    {msg_usa26, msg_usa28, msg_usa49, msg_usa90} msg_format;
+       enum    {msg_usa26, msg_usa28, msg_usa49, msg_usa90, msg_usa67} msg_format;
 
                /* Number of physical ports */
        int     num_ports;
@@ -264,6 +270,9 @@ struct keyspan_device_details {
                /* Endpoint used for input status */
        int     instat_endpoint;
 
+               /* Endpoint used for input data 49WG only */
+       int     indat_endpoint;
+
                /* Endpoint used for global control functions */
        int     glocont_endpoint;
 
@@ -287,6 +296,7 @@ static const struct keyspan_device_details usa18x_device_details = {
        .inack_endpoints        = {0x85},
        .outcont_endpoints      = {0x05},
        .instat_endpoint        = 0x87,
+       .indat_endpoint         = -1,
        .glocont_endpoint       = 0x07,
        .calculate_baud_rate    = keyspan_usa19w_calc_baud,
        .baudclk                = KEYSPAN_USA18X_BAUDCLK,
@@ -303,6 +313,7 @@ static const struct keyspan_device_details usa19_device_details = {
        .inack_endpoints        = {0x83},
        .outcont_endpoints      = {0x03},
        .instat_endpoint        = 0x84,
+       .indat_endpoint         = -1,
        .glocont_endpoint       = -1,
        .calculate_baud_rate    = keyspan_usa19_calc_baud,
        .baudclk                = KEYSPAN_USA19_BAUDCLK,
@@ -319,6 +330,7 @@ static const struct keyspan_device_details usa19qi_device_details = {
        .inack_endpoints        = {0x83},
        .outcont_endpoints      = {0x03},
        .instat_endpoint        = 0x84,
+       .indat_endpoint         = -1,
        .glocont_endpoint       = -1,
        .calculate_baud_rate    = keyspan_usa28_calc_baud,
        .baudclk                = KEYSPAN_USA19_BAUDCLK,
@@ -335,6 +347,7 @@ static const struct keyspan_device_details mpr_device_details = {
        .inack_endpoints        = {0x83},
        .outcont_endpoints      = {0x03},
        .instat_endpoint        = 0x84,
+       .indat_endpoint         = -1,
        .glocont_endpoint       = -1,
        .calculate_baud_rate    = keyspan_usa28_calc_baud,
        .baudclk                = KEYSPAN_USA19_BAUDCLK,
@@ -351,6 +364,7 @@ static const struct keyspan_device_details usa19qw_device_details = {
        .inack_endpoints        = {0x85},
        .outcont_endpoints      = {0x05},
        .instat_endpoint        = 0x87,
+       .indat_endpoint         = -1,
        .glocont_endpoint       = 0x07,
        .calculate_baud_rate    = keyspan_usa19w_calc_baud,
        .baudclk                = KEYSPAN_USA19W_BAUDCLK,
@@ -367,6 +381,7 @@ static const struct keyspan_device_details usa19w_device_details = {
        .inack_endpoints        = {0x85},
        .outcont_endpoints      = {0x05},
        .instat_endpoint        = 0x87,
+       .indat_endpoint         = -1,
        .glocont_endpoint       = 0x07,
        .calculate_baud_rate    = keyspan_usa19w_calc_baud,
        .baudclk                = KEYSPAN_USA19W_BAUDCLK,
@@ -383,6 +398,7 @@ static const struct keyspan_device_details usa19hs_device_details = {
        .inack_endpoints        = {-1},
        .outcont_endpoints      = {0x02},
        .instat_endpoint        = 0x82,
+       .indat_endpoint         = -1,
        .glocont_endpoint       = -1,
        .calculate_baud_rate    = keyspan_usa19hs_calc_baud,
        .baudclk                = KEYSPAN_USA19HS_BAUDCLK,
@@ -399,6 +415,7 @@ static const struct keyspan_device_details usa28_device_details = {
        .inack_endpoints        = {0x85, 0x86},
        .outcont_endpoints      = {0x05, 0x06},
        .instat_endpoint        = 0x87,
+       .indat_endpoint         = -1,
        .glocont_endpoint       = 0x07,
        .calculate_baud_rate    = keyspan_usa28_calc_baud,
        .baudclk                = KEYSPAN_USA28_BAUDCLK,                
@@ -415,6 +432,7 @@ static const struct keyspan_device_details usa28x_device_details = {
        .inack_endpoints        = {0x85, 0x86},
        .outcont_endpoints      = {0x05, 0x06},
        .instat_endpoint        = 0x87,
+       .indat_endpoint         = -1,
        .glocont_endpoint       = 0x07,
        .calculate_baud_rate    = keyspan_usa19w_calc_baud,
        .baudclk                = KEYSPAN_USA28X_BAUDCLK,
@@ -431,11 +449,28 @@ static const struct keyspan_device_details usa28xa_device_details = {
        .inack_endpoints        = {0x85, 0x86},
        .outcont_endpoints      = {0x05, 0x06},
        .instat_endpoint        = 0x87,
+       .indat_endpoint         = -1,
        .glocont_endpoint       = 0x07,
        .calculate_baud_rate    = keyspan_usa19w_calc_baud,
        .baudclk                = KEYSPAN_USA28X_BAUDCLK,
 };
 
+static const struct keyspan_device_details usa28xg_device_details = {
+       .product_id             = keyspan_usa28xg_product_id,
+       .msg_format             = msg_usa67,
+       .num_ports              = 2,
+       .indat_endp_flip        = 0,
+       .outdat_endp_flip       = 0,
+       .indat_endpoints        = {0x84, 0x88},
+       .outdat_endpoints       = {0x02, 0x06},
+       .inack_endpoints        = {-1, -1},
+       .outcont_endpoints      = {-1, -1},
+       .instat_endpoint        = 0x81,
+       .indat_endpoint         = -1,
+       .glocont_endpoint       = 0x01,
+       .calculate_baud_rate    = keyspan_usa19w_calc_baud,
+       .baudclk                = KEYSPAN_USA28X_BAUDCLK,
+};
 /* We don't need a separate entry for the usa28xb as it appears as a 28x anyway */
 
 static const struct keyspan_device_details usa49w_device_details = {
@@ -449,6 +484,7 @@ static const struct keyspan_device_details usa49w_device_details = {
        .inack_endpoints        = {-1, -1, -1, -1},
        .outcont_endpoints      = {-1, -1, -1, -1},
        .instat_endpoint        = 0x87,
+       .indat_endpoint         = -1,
        .glocont_endpoint       = 0x07,
        .calculate_baud_rate    = keyspan_usa19w_calc_baud,
        .baudclk                = KEYSPAN_USA49W_BAUDCLK,
@@ -465,11 +501,29 @@ static const struct keyspan_device_details usa49wlc_device_details = {
        .inack_endpoints        = {-1, -1, -1, -1},
        .outcont_endpoints      = {-1, -1, -1, -1},
        .instat_endpoint        = 0x87,
+       .indat_endpoint         = -1,
        .glocont_endpoint       = 0x07,
        .calculate_baud_rate    = keyspan_usa19w_calc_baud,
        .baudclk                = KEYSPAN_USA19W_BAUDCLK,
 };
 
+static const struct keyspan_device_details usa49wg_device_details = {
+       .product_id             = keyspan_usa49wg_product_id,
+       .msg_format             = msg_usa49,
+       .num_ports              = 4,
+       .indat_endp_flip        = 0,
+       .outdat_endp_flip       = 0,
+       .indat_endpoints        = {-1, -1, -1, -1},             /* single 'global' data in EP */
+       .outdat_endpoints       = {0x01, 0x02, 0x04, 0x06},
+       .inack_endpoints        = {-1, -1, -1, -1},
+       .outcont_endpoints      = {-1, -1, -1, -1},
+       .instat_endpoint        = 0x81,
+       .indat_endpoint         = 0x88,
+       .glocont_endpoint       = 0x00,                         /* uses control EP */
+       .calculate_baud_rate    = keyspan_usa19w_calc_baud,
+       .baudclk                = KEYSPAN_USA19W_BAUDCLK,
+};
+
 static const struct keyspan_device_details *keyspan_devices[] = {
        &usa18x_device_details,
        &usa19_device_details,
@@ -481,9 +535,11 @@ static const struct keyspan_device_details *keyspan_devices[] = {
        &usa28_device_details,
        &usa28x_device_details,
        &usa28xa_device_details,
+       &usa28xg_device_details,
        /* 28xb not required as it renumerates as a 28x */
        &usa49w_device_details,
        &usa49wlc_device_details,
+       &usa49wg_device_details,
        NULL,
 };
 
@@ -510,8 +566,11 @@ static struct usb_device_id keyspan_ids_combined[] = {
        { USB_DEVICE(KEYSPAN_VENDOR_ID, keyspan_usa28_product_id) },
        { USB_DEVICE(KEYSPAN_VENDOR_ID, keyspan_usa28x_product_id) },
        { USB_DEVICE(KEYSPAN_VENDOR_ID, keyspan_usa28xa_product_id) },
+       { USB_DEVICE(KEYSPAN_VENDOR_ID, keyspan_usa28xb_product_id) },
+       { USB_DEVICE(KEYSPAN_VENDOR_ID, keyspan_usa28xg_product_id) },
        { USB_DEVICE(KEYSPAN_VENDOR_ID, keyspan_usa49w_product_id)},
        { USB_DEVICE(KEYSPAN_VENDOR_ID, keyspan_usa49wlc_product_id)},
+       { USB_DEVICE(KEYSPAN_VENDOR_ID, keyspan_usa49wg_product_id)},
        { } /* Terminating entry */
 };
 
@@ -557,12 +616,15 @@ static struct usb_device_id keyspan_2port_ids[] = {
        { USB_DEVICE(KEYSPAN_VENDOR_ID, keyspan_usa28_product_id) },
        { USB_DEVICE(KEYSPAN_VENDOR_ID, keyspan_usa28x_product_id) },
        { USB_DEVICE(KEYSPAN_VENDOR_ID, keyspan_usa28xa_product_id) },
+       { USB_DEVICE(KEYSPAN_VENDOR_ID, keyspan_usa28xb_product_id) },
+       { USB_DEVICE(KEYSPAN_VENDOR_ID, keyspan_usa28xg_product_id) },
        { } /* Terminating entry */
 };
 
 static struct usb_device_id keyspan_4port_ids[] = {
        { USB_DEVICE(KEYSPAN_VENDOR_ID, keyspan_usa49w_product_id) },
        { USB_DEVICE(KEYSPAN_VENDOR_ID, keyspan_usa49wlc_product_id)},
+       { USB_DEVICE(KEYSPAN_VENDOR_ID, keyspan_usa49wg_product_id)},
        { } /* Terminating entry */
 };
 
@@ -573,7 +635,6 @@ static struct usb_serial_driver keyspan_pre_device = {
                .name           = "keyspan_no_firm",
        },
        .description            = "Keyspan - (without firmware)",
-       .usb_driver             = &keyspan_driver,
        .id_table               = keyspan_pre_ids,
        .num_interrupt_in       = NUM_DONT_CARE,
        .num_bulk_in            = NUM_DONT_CARE,
@@ -588,7 +649,6 @@ static struct usb_serial_driver keyspan_1port_device = {
                .name           = "keyspan_1",
        },
        .description            = "Keyspan 1 port adapter",
-       .usb_driver             = &keyspan_driver,
        .id_table               = keyspan_1port_ids,
        .num_interrupt_in       = NUM_DONT_CARE,
        .num_bulk_in            = NUM_DONT_CARE,
@@ -616,7 +676,6 @@ static struct usb_serial_driver keyspan_2port_device = {
                .name           = "keyspan_2",
        },
        .description            = "Keyspan 2 port adapter",
-       .usb_driver             = &keyspan_driver,
        .id_table               = keyspan_2port_ids,
        .num_interrupt_in       = NUM_DONT_CARE,
        .num_bulk_in            = NUM_DONT_CARE,
@@ -644,11 +703,10 @@ static struct usb_serial_driver keyspan_4port_device = {
                .name           = "keyspan_4",
        },
        .description            = "Keyspan 4 port adapter",
-       .usb_driver             = &keyspan_driver,
        .id_table               = keyspan_4port_ids,
        .num_interrupt_in       = NUM_DONT_CARE,
-       .num_bulk_in            = 5,
-       .num_bulk_out           = 5,
+       .num_bulk_in            = NUM_DONT_CARE,
+       .num_bulk_out           = NUM_DONT_CARE,
        .num_ports              = 4,
        .open                   = keyspan_open,
        .close                  = keyspan_close,
diff --git a/drivers/usb/serial/keyspan_usa67msg.h b/drivers/usb/serial/keyspan_usa67msg.h
new file mode 100644 (file)
index 0000000..20fa3e2
--- /dev/null
@@ -0,0 +1,254 @@
+/*
+       usa67msg.h
+
+       Copyright (c) 1998-2007 InnoSys Incorporated.  All Rights Reserved
+       This file is available under a BSD-style copyright
+
+       Keyspan USB Async Firmware to run on Anchor FX1
+
+       Redistribution and use in source and binary forms, with or without
+       modification, are permitted provided that the following conditions are
+       met:
+
+       1. Redistributions of source code must retain this licence text
+       without modification, this list of conditions, and the following
+       disclaimer.  The following copyright notice must appear immediately at
+       the beginning of all source files:
+
+               Copyright (c) 1998-2007 InnoSys Incorporated.  All Rights Reserved
+
+               This file is available under a BSD-style copyright
+
+       2. Redistributions in binary form must reproduce the above copyright
+       notice, this list of conditions and the following disclaimer in the
+       documentation and/or other materials provided with the distribution.
+
+       3. The name of InnoSys Incorprated may not be used to endorse or promote
+       products derived from this software without specific prior written
+       permission.
+
+       THIS SOFTWARE IS PROVIDED BY INNOSYS CORP. ``AS IS'' AND ANY EXPRESS OR
+       IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
+       OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+       NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
+       INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+       (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+       SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+       CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+       LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
+       OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
+       SUCH DAMAGE.
+
+       Fourth revision: This message format supports the USA28XG
+
+       Buffer formats for RX/TX data messages are not defined by
+       a structure, but are described here:
+
+       USB OUT (host -> USAxx, transmit) messages contain a
+       REQUEST_ACK indicator (set to 0xff to request an ACK at the
+       completion of transmit; 0x00 otherwise), followed by data:
+
+               RQSTACK DAT DAT DAT ...
+
+       with a total data length of up to 63.
+
+       USB IN (USAxx -> host, receive) messages begin with a status
+       byte in which the 0x80 bit is either:
+
+               (a)     0x80 bit clear
+                       indicates that the bytes following it are all data
+                       bytes:
+
+                               STAT DATA DATA DATA DATA DATA ...
+
+                       for a total of up to 63 DATA bytes,
+
+       or:
+
+               (b)     0x80 bit set
+                       indiates that the bytes following alternate data and
+                       status bytes:
+
+                               STAT DATA STAT DATA STAT DATA STAT DATA ...
+
+                       for a total of up to 32 DATA bytes.
+
+       The valid bits in the STAT bytes are:
+
+               OVERRUN 0x02
+               PARITY  0x04
+               FRAMING 0x08
+               BREAK   0x10
+
+       Notes:
+
+       (1) The OVERRUN bit can appear in either (a) or (b) format
+               messages, but the but the PARITY/FRAMING/BREAK bits
+               only appear in (b) format messages.
+       (2) For the host to determine the exact point at which the
+               overrun occurred (to identify the point in the data
+               stream at which the data was lost), it needs to count
+               128 characters, starting at the first character of the
+               message in which OVERRUN was reported; the lost character(s)
+               would have been received between the 128th and 129th
+               characters.
+       (3)     An RX data message in which the first byte has 0x80 clear
+               serves as a "break off" indicator.
+
+       revision history:
+
+       1999feb10       add reportHskiaChanges to allow us to ignore them
+       1999feb10       add txAckThreshold for fast+loose throughput enhancement
+       1999mar30       beef up support for RX error reporting
+       1999apr14       add resetDataToggle to control message
+       2000jan04       merge with usa17msg.h
+       2000jun01       add extended BSD-style copyright text
+       2001jul05       change message format to improve OVERRUN case
+       2002jun05       update copyright date, improve comments
+       2006feb06       modify for FX1 chip
+
+*/
+
+#ifndef        __USA67MSG__
+#define        __USA67MSG__
+
+
+// all things called "ControlMessage" are sent on the 'control' endpoint
+
+typedef struct keyspan_usa67_portControlMessage
+{
+       u8      port;           // 0 or 1 (selects port)
+       /*
+               there are three types of "commands" sent in the control message:
+
+               1.      configuration changes which must be requested by setting
+                       the corresponding "set" flag (and should only be requested
+                       when necessary, to reduce overhead on the device):
+       */
+       u8      setClocking,    // host requests baud rate be set
+               baudLo,                 // host does baud divisor calculation
+               baudHi,                 // baudHi is only used for first port (gives lower rates)
+               externalClock_txClocking,
+                                               // 0=internal, other=external
+
+               setLcr,                 // host requests lcr be set
+               lcr,                    // use PARITY, STOPBITS, DATABITS below
+
+               setFlowControl, // host requests flow control be set
+               ctsFlowControl, // 1=use CTS flow control, 0=don't
+               xonFlowControl, // 1=use XON/XOFF flow control, 0=don't
+               xonChar,                // specified in current character format
+               xoffChar,               // specified in current character format
+
+               setTxTriState_setRts,
+                                               // host requests TX tri-state be set
+               txTriState_rts, // 1=active (normal), 0=tristate (off)
+
+               setHskoa_setDtr,
+                                               // host requests HSKOA output be set
+               hskoa_dtr,              // 1=on, 0=off
+
+               setPrescaler,   // host requests prescalar be set (default: 13)
+               prescaler;              // specified as N/8; values 8-ff are valid
+                                               // must be set any time internal baud rate is set;
+                                               // must not be set when external clocking is used
+
+       /*
+               3.      configuration data which is simply used as is (no overhead,
+                       but must be specified correctly in every host message).
+       */
+       u8      forwardingLength,  // forward when this number of chars available
+               reportHskiaChanges_dsrFlowControl,
+                                               // 1=normal; 0=ignore external clock
+                                               // 1=use DSR flow control, 0=don't
+               txAckThreshold, // 0=not allowed, 1=normal, 2-255 deliver ACK faster
+               loopbackMode;   // 0=no loopback, 1=loopback enabled
+
+       /*
+               4.      commands which are flags only; these are processed in order
+                       (so that, e.g., if both _txOn and _txOff flags are set, the
+                       port ends in a TX_OFF state); any non-zero value is respected
+       */
+       u8      _txOn,                  // enable transmitting (and continue if there's data)
+               _txOff,                 // stop transmitting
+               txFlush,                // toss outbound data
+               txBreak,                // turn on break (cleared by _txOn)
+               rxOn,                   // turn on receiver
+               rxOff,                  // turn off receiver
+               rxFlush,                // toss inbound data
+               rxForward,              // forward all inbound data, NOW (as if fwdLen==1)
+               returnStatus,   // return current status (even if it hasn't changed)
+               resetDataToggle;// reset data toggle state to DATA0
+
+} keyspan_usa67_portControlMessage;
+
+// defines for bits in lcr
+#define        USA_DATABITS_5          0x00
+#define        USA_DATABITS_6          0x01
+#define        USA_DATABITS_7          0x02
+#define        USA_DATABITS_8          0x03
+#define        STOPBITS_5678_1         0x00    // 1 stop bit for all byte sizes
+#define        STOPBITS_5_1p5          0x04    // 1.5 stop bits for 5-bit byte
+#define        STOPBITS_678_2          0x04    // 2 stop bits for 6/7/8-bit byte
+#define        USA_PARITY_NONE         0x00
+#define        USA_PARITY_ODD          0x08
+#define        USA_PARITY_EVEN         0x18
+#define        PARITY_1                        0x28
+#define        PARITY_0                        0x38
+
+// all things called "StatusMessage" are sent on the status endpoint
+
+typedef struct keyspan_usa67_portStatusMessage // one for each port
+{
+       u8      port,                   // 0=first, 1=second, other=see below
+               hskia_cts,              // reports HSKIA pin
+               gpia_dcd,               // reports GPIA pin
+               _txOff,                 // port has been disabled (by host)
+               _txXoff,                // port is in XOFF state (either host or RX XOFF)
+               txAck,                  // indicates a TX message acknowledgement
+               rxEnabled,              // as configured by rxOn/rxOff 1=on, 0=off
+               controlResponse;// 1=a control message has been processed
+} keyspan_usa67_portStatusMessage;
+
+// bits in RX data message when STAT byte is included
+#define        RXERROR_OVERRUN 0x02
+#define        RXERROR_PARITY  0x04
+#define        RXERROR_FRAMING 0x08
+#define        RXERROR_BREAK   0x10
+
+typedef struct keyspan_usa67_globalControlMessage
+{
+       u8      port,                           // 3
+               sendGlobalStatus,       // 2=request for two status responses
+               resetStatusToggle,      // 1=reset global status toggle
+               resetStatusCount;       // a cycling value
+} keyspan_usa67_globalControlMessage;
+
+typedef struct keyspan_usa67_globalStatusMessage
+{
+       u8      port,                           // 3
+               sendGlobalStatus,       // from request, decremented
+               resetStatusCount;       // as in request
+} keyspan_usa67_globalStatusMessage;
+
+typedef struct keyspan_usa67_globalDebugMessage
+{
+       u8      port,                           // 2
+               a,
+               b,
+               c,
+               d;
+} keyspan_usa67_globalDebugMessage;
+
+// ie: the maximum length of an FX1 endpoint buffer
+#define        MAX_DATA_LEN                    64
+
+// update status approx. 60 times a second (16.6666 ms)
+#define        STATUS_UPDATE_INTERVAL  16
+
+// status rationing tuning value (each port gets checked each n ms)
+#define        STATUS_RATION   10
+
+#endif
+
+