This option enables support for MIPS Technologies MIPSsim software
emulator.
-config MOMENCO_OCELOT
- bool "Momentum Ocelot board"
- select DMA_NONCOHERENT
- select HW_HAS_PCI
- select IRQ_CPU
- select IRQ_CPU_RM7K
- select PCI_GT64XXX_PCI0
- select RM7000_CPU_SCACHE
- select SWAP_IO_SPACE
- select SYS_HAS_CPU_RM7000
- select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_64BIT_KERNEL
- select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_KGDB
- help
- The Ocelot is a MIPS-based Single Board Computer (SBC) made by
- Momentum Computer <http://www.momenco.com/>.
-
config DDB5477
bool "NEC DDB Vrc-5477"
select DDB5XXX_COMMON
cflags-$(CONFIG_MIPS_SIM) += -Iinclude/asm-mips/mach-mipssim
load-$(CONFIG_MIPS_SIM) += 0x80100000
-#
-# Momentum Ocelot board
-#
-# The Ocelot setup.o must be linked early - it does the ioremap() for the
-# mips_io_port_base.
-#
-core-$(CONFIG_MOMENCO_OCELOT) += arch/mips/gt64120/common/ \
- arch/mips/gt64120/momenco_ocelot/
-cflags-$(CONFIG_MOMENCO_OCELOT) += -Iinclude/asm-mips/mach-ocelot
-load-$(CONFIG_MOMENCO_OCELOT) += 0xffffffff80100000
-
#
# PMC-Sierra MSP SOCs
#
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_MIPS_SEAD is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
-# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_DDB5477 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_MIPS_SEAD is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
-# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_DDB5477 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
CONFIG_MIPS_SIM=y
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
+++ /dev/null
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.20
-# Tue Feb 20 21:47:36 2007
-#
-CONFIG_MIPS=y
-
-#
-# Machine selection
-#
-CONFIG_ZONE_DMA=y
-# CONFIG_MIPS_MTX1 is not set
-# CONFIG_MIPS_BOSPORUS is not set
-# CONFIG_MIPS_PB1000 is not set
-# CONFIG_MIPS_PB1100 is not set
-# CONFIG_MIPS_PB1500 is not set
-# CONFIG_MIPS_PB1550 is not set
-# CONFIG_MIPS_PB1200 is not set
-# CONFIG_MIPS_DB1000 is not set
-# CONFIG_MIPS_DB1100 is not set
-# CONFIG_MIPS_DB1500 is not set
-# CONFIG_MIPS_DB1550 is not set
-# CONFIG_MIPS_DB1200 is not set
-# CONFIG_MIPS_MIRAGE is not set
-# CONFIG_BASLER_EXCITE is not set
-# CONFIG_MIPS_COBALT is not set
-# CONFIG_MACH_DECSTATION is not set
-# CONFIG_MACH_JAZZ is not set
-# CONFIG_MIPS_ATLAS is not set
-# CONFIG_MIPS_MALTA is not set
-# CONFIG_MIPS_SEAD is not set
-# CONFIG_WR_PPMC is not set
-# CONFIG_MIPS_SIM is not set
-# CONFIG_MOMENCO_JAGUAR_ATX is not set
-CONFIG_MOMENCO_OCELOT=y
-# CONFIG_MOMENCO_OCELOT_G is not set
-# CONFIG_MIPS_XXS1500 is not set
-# CONFIG_PNX8550_JBS is not set
-# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
-# CONFIG_MACH_VR41XX is not set
-# CONFIG_PMC_YOSEMITE is not set
-# CONFIG_QEMU is not set
-# CONFIG_MARKEINS is not set
-# CONFIG_SGI_IP22 is not set
-# CONFIG_SGI_IP27 is not set
-# CONFIG_SGI_IP32 is not set
-# CONFIG_SIBYTE_BIGSUR is not set
-# CONFIG_SIBYTE_SWARM is not set
-# CONFIG_SIBYTE_SENTOSA is not set
-# CONFIG_SIBYTE_RHONE is not set
-# CONFIG_SIBYTE_CARMEL is not set
-# CONFIG_SIBYTE_PTSWARM is not set
-# CONFIG_SIBYTE_LITTLESUR is not set
-# CONFIG_SIBYTE_CRHINE is not set
-# CONFIG_SIBYTE_CRHONE is not set
-# CONFIG_SNI_RM is not set
-# CONFIG_TOSHIBA_JMR3927 is not set
-# CONFIG_TOSHIBA_RBTX4927 is not set
-# CONFIG_TOSHIBA_RBTX4938 is not set
-CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_GENERIC_FIND_NEXT_BIT=y
-CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_GENERIC_TIME=y
-CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
-# CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ is not set
-CONFIG_DMA_NONCOHERENT=y
-CONFIG_DMA_NEED_PCI_MAP_STATE=y
-CONFIG_CPU_BIG_ENDIAN=y
-# CONFIG_CPU_LITTLE_ENDIAN is not set
-CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
-CONFIG_IRQ_CPU=y
-CONFIG_IRQ_CPU_RM7K=y
-CONFIG_MIPS_GT64120=y
-CONFIG_SWAP_IO_SPACE=y
-# CONFIG_SYSCLK_75 is not set
-# CONFIG_SYSCLK_83 is not set
-CONFIG_SYSCLK_100=y
-CONFIG_MIPS_L1_CACHE_SHIFT=5
-
-#
-# CPU selection
-#
-# CONFIG_CPU_MIPS32_R1 is not set
-# CONFIG_CPU_MIPS32_R2 is not set
-# CONFIG_CPU_MIPS64_R1 is not set
-# CONFIG_CPU_MIPS64_R2 is not set
-# CONFIG_CPU_R3000 is not set
-# CONFIG_CPU_TX39XX is not set
-# CONFIG_CPU_VR41XX is not set
-# CONFIG_CPU_R4300 is not set
-# CONFIG_CPU_R4X00 is not set
-# CONFIG_CPU_TX49XX is not set
-# CONFIG_CPU_R5000 is not set
-# CONFIG_CPU_R5432 is not set
-# CONFIG_CPU_R6000 is not set
-# CONFIG_CPU_NEVADA is not set
-# CONFIG_CPU_R8000 is not set
-# CONFIG_CPU_R10000 is not set
-CONFIG_CPU_RM7000=y
-# CONFIG_CPU_RM9000 is not set
-# CONFIG_CPU_SB1 is not set
-CONFIG_SYS_HAS_CPU_RM7000=y
-CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
-CONFIG_SYS_SUPPORTS_64BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_64BIT_KERNEL=y
-
-#
-# Kernel type
-#
-CONFIG_32BIT=y
-# CONFIG_64BIT is not set
-CONFIG_PAGE_SIZE_4KB=y
-# CONFIG_PAGE_SIZE_8KB is not set
-# CONFIG_PAGE_SIZE_16KB is not set
-# CONFIG_PAGE_SIZE_64KB is not set
-CONFIG_BOARD_SCACHE=y
-CONFIG_RM7000_CPU_SCACHE=y
-CONFIG_CPU_HAS_PREFETCH=y
-CONFIG_MIPS_MT_DISABLED=y
-# CONFIG_MIPS_MT_SMP is not set
-# CONFIG_MIPS_MT_SMTC is not set
-# CONFIG_MIPS_VPE_LOADER is not set
-# CONFIG_64BIT_PHYS_ADDR is not set
-CONFIG_CPU_HAS_LLSC=y
-CONFIG_CPU_HAS_SYNC=y
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_GENERIC_IRQ_PROBE=y
-CONFIG_CPU_SUPPORTS_HIGHMEM=y
-CONFIG_ARCH_FLATMEM_ENABLE=y
-CONFIG_SELECT_MEMORY_MODEL=y
-CONFIG_FLATMEM_MANUAL=y
-# CONFIG_DISCONTIGMEM_MANUAL is not set
-# CONFIG_SPARSEMEM_MANUAL is not set
-CONFIG_FLATMEM=y
-CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-CONFIG_SPLIT_PTLOCK_CPUS=4
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-# CONFIG_HZ_48 is not set
-# CONFIG_HZ_100 is not set
-# CONFIG_HZ_128 is not set
-# CONFIG_HZ_250 is not set
-# CONFIG_HZ_256 is not set
-CONFIG_HZ_1000=y
-# CONFIG_HZ_1024 is not set
-CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
-CONFIG_HZ=1000
-CONFIG_PREEMPT_NONE=y
-# CONFIG_PREEMPT_VOLUNTARY is not set
-# CONFIG_PREEMPT is not set
-# CONFIG_KEXEC is not set
-CONFIG_LOCKDEP_SUPPORT=y
-CONFIG_STACKTRACE_SUPPORT=y
-CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-#
-# Code maturity level options
-#
-CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-
-#
-# General setup
-#
-CONFIG_LOCALVERSION=""
-CONFIG_LOCALVERSION_AUTO=y
-CONFIG_SWAP=y
-CONFIG_SYSVIPC=y
-# CONFIG_IPC_NS is not set
-CONFIG_SYSVIPC_SYSCTL=y
-# CONFIG_POSIX_MQUEUE is not set
-# CONFIG_BSD_PROCESS_ACCT is not set
-# CONFIG_TASKSTATS is not set
-# CONFIG_UTS_NS is not set
-# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
-CONFIG_SYSFS_DEPRECATED=y
-CONFIG_RELAY=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-CONFIG_SYSCTL=y
-CONFIG_EMBEDDED=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_HOTPLUG is not set
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-CONFIG_ELF_CORE=y
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-CONFIG_EPOLL=y
-CONFIG_SHMEM=y
-CONFIG_SLAB=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
-CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
-
-#
-# Loadable module support
-#
-# CONFIG_MODULES is not set
-
-#
-# Block layer
-#
-CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
-CONFIG_DEFAULT_AS=y
-# CONFIG_DEFAULT_DEADLINE is not set
-# CONFIG_DEFAULT_CFQ is not set
-# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="anticipatory"
-
-#
-# Bus options (PCI, PCMCIA, EISA, ISA, TC)
-#
-CONFIG_HW_HAS_PCI=y
-# CONFIG_PCI is not set
-CONFIG_MMU=y
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
-
-#
-# PCI Hotplug Support
-#
-
-#
-# Executable file formats
-#
-CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_MISC is not set
-CONFIG_TRAD_SIGNALS=y
-
-#
-# Power management options
-#
-CONFIG_PM=y
-# CONFIG_PM_LEGACY is not set
-# CONFIG_PM_DEBUG is not set
-# CONFIG_PM_SYSFS_DEPRECATED is not set
-
-#
-# Networking
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-# CONFIG_NETDEBUG is not set
-# CONFIG_PACKET is not set
-CONFIG_UNIX=y
-CONFIG_XFRM=y
-CONFIG_XFRM_USER=y
-# CONFIG_XFRM_SUB_POLICY is not set
-CONFIG_XFRM_MIGRATE=y
-CONFIG_NET_KEY=y
-CONFIG_NET_KEY_MIGRATE=y
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-CONFIG_IP_PNP=y
-# CONFIG_IP_PNP_DHCP is not set
-CONFIG_IP_PNP_BOOTP=y
-# CONFIG_IP_PNP_RARP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
-# CONFIG_INET_TUNNEL is not set
-CONFIG_INET_XFRM_MODE_TRANSPORT=y
-CONFIG_INET_XFRM_MODE_TUNNEL=y
-CONFIG_INET_XFRM_MODE_BEET=y
-CONFIG_INET_DIAG=y
-CONFIG_INET_TCP_DIAG=y
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_CUBIC=y
-CONFIG_DEFAULT_TCP_CONG="cubic"
-CONFIG_TCP_MD5SIG=y
-# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
-CONFIG_NETWORK_SECMARK=y
-# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
-# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
-# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
-# CONFIG_TIPC is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
-# CONFIG_NET_SCHED is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-CONFIG_IEEE80211=y
-# CONFIG_IEEE80211_DEBUG is not set
-CONFIG_IEEE80211_CRYPT_WEP=y
-CONFIG_IEEE80211_CRYPT_CCMP=y
-CONFIG_IEEE80211_SOFTMAC=y
-# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set
-CONFIG_WIRELESS_EXT=y
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_STANDALONE=y
-CONFIG_PREVENT_FIRMWARE_BUILD=y
-# CONFIG_SYS_HYPERVISOR is not set
-
-#
-# Connector - unified userspace <-> kernelspace linker
-#
-CONFIG_CONNECTOR=y
-CONFIG_PROC_EVENTS=y
-
-#
-# Memory Technology Devices (MTD)
-#
-# CONFIG_MTD is not set
-
-#
-# Parallel port support
-#
-# CONFIG_PARPORT is not set
-
-#
-# Plug and Play support
-#
-# CONFIG_PNPACPI is not set
-
-#
-# Block devices
-#
-# CONFIG_BLK_DEV_COW_COMMON is not set
-# CONFIG_BLK_DEV_LOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
-# CONFIG_BLK_DEV_RAM is not set
-# CONFIG_BLK_DEV_INITRD is not set
-CONFIG_CDROM_PKTCDVD=y
-CONFIG_CDROM_PKTCDVD_BUFFERS=8
-# CONFIG_CDROM_PKTCDVD_WCACHE is not set
-CONFIG_ATA_OVER_ETH=y
-
-#
-# Misc devices
-#
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-CONFIG_RAID_ATTRS=y
-# CONFIG_SCSI is not set
-# CONFIG_SCSI_NETLINK is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
-# CONFIG_ATA is not set
-
-#
-# Multi-device support (RAID and LVM)
-#
-# CONFIG_MD is not set
-
-#
-# Fusion MPT device support
-#
-# CONFIG_FUSION is not set
-
-#
-# IEEE 1394 (FireWire) support
-#
-
-#
-# I2O device support
-#
-
-#
-# Network device support
-#
-CONFIG_NETDEVICES=y
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-
-#
-# PHY device support
-#
-CONFIG_PHYLIB=y
-
-#
-# MII PHY device drivers
-#
-CONFIG_MARVELL_PHY=y
-CONFIG_DAVICOM_PHY=y
-CONFIG_QSEMI_PHY=y
-CONFIG_LXT_PHY=y
-CONFIG_CICADA_PHY=y
-CONFIG_VITESSE_PHY=y
-CONFIG_SMSC_PHY=y
-# CONFIG_BROADCOM_PHY is not set
-# CONFIG_FIXED_PHY is not set
-
-#
-# Ethernet (10 or 100Mbit)
-#
-CONFIG_NET_ETHERNET=y
-# CONFIG_MII is not set
-# CONFIG_DM9000 is not set
-
-#
-# Ethernet (1000 Mbit)
-#
-
-#
-# Ethernet (10000 Mbit)
-#
-
-#
-# Token Ring devices
-#
-
-#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Wan interfaces
-#
-# CONFIG_WAN is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
-# CONFIG_NETCONSOLE is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-
-#
-# ISDN subsystem
-#
-# CONFIG_ISDN is not set
-
-#
-# Telephony Support
-#
-# CONFIG_PHONE is not set
-
-#
-# Input device support
-#
-CONFIG_INPUT=y
-# CONFIG_INPUT_FF_MEMLESS is not set
-
-#
-# Userland interfaces
-#
-CONFIG_INPUT_MOUSEDEV=y
-CONFIG_INPUT_MOUSEDEV_PSAUX=y
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
-# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
-# CONFIG_INPUT_EVDEV is not set
-# CONFIG_INPUT_EVBUG is not set
-
-#
-# Input Device Drivers
-#
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TOUCHSCREEN is not set
-# CONFIG_INPUT_MISC is not set
-
-#
-# Hardware I/O ports
-#
-CONFIG_SERIO=y
-# CONFIG_SERIO_I8042 is not set
-CONFIG_SERIO_SERPORT=y
-# CONFIG_SERIO_LIBPS2 is not set
-CONFIG_SERIO_RAW=y
-# CONFIG_GAMEPORT is not set
-
-#
-# Character devices
-#
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-CONFIG_HW_CONSOLE=y
-CONFIG_VT_HW_CONSOLE_BINDING=y
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=4
-CONFIG_SERIAL_8250_RUNTIME_UARTS=4
-# CONFIG_SERIAL_8250_EXTENDED is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-CONFIG_UNIX98_PTYS=y
-CONFIG_LEGACY_PTYS=y
-CONFIG_LEGACY_PTY_COUNT=256
-
-#
-# IPMI
-#
-# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
-# CONFIG_WATCHDOG is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_RTC is not set
-# CONFIG_GEN_RTC is not set
-# CONFIG_DTLK is not set
-# CONFIG_R3964 is not set
-# CONFIG_RAW_DRIVER is not set
-
-#
-# TPM devices
-#
-# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
-# CONFIG_I2C is not set
-
-#
-# SPI support
-#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
-
-#
-# Dallas's 1-wire bus
-#
-# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
-# CONFIG_HWMON is not set
-# CONFIG_HWMON_VID is not set
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-
-#
-# Digital Video Broadcasting Devices
-#
-# CONFIG_DVB is not set
-
-#
-# Graphics support
-#
-# CONFIG_FIRMWARE_EDID is not set
-# CONFIG_FB is not set
-
-#
-# Console display driver support
-#
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_DUMMY_CONSOLE=y
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-
-#
-# HID Devices
-#
-# CONFIG_HID is not set
-
-#
-# USB support
-#
-# CONFIG_USB_ARCH_HAS_HCD is not set
-# CONFIG_USB_ARCH_HAS_OHCI is not set
-# CONFIG_USB_ARCH_HAS_EHCI is not set
-
-#
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
-#
-
-#
-# USB Gadget Support
-#
-# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
-# CONFIG_MMC is not set
-
-#
-# LED devices
-#
-# CONFIG_NEW_LEDS is not set
-
-#
-# LED drivers
-#
-
-#
-# LED Triggers
-#
-
-#
-# InfiniBand support
-#
-
-#
-# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
-#
-
-#
-# Real Time Clock
-#
-# CONFIG_RTC_CLASS is not set
-
-#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
-#
-
-#
-# Auxiliary Display support
-#
-
-#
-# Virtualization
-#
-
-#
-# File systems
-#
-CONFIG_EXT2_FS=y
-# CONFIG_EXT2_FS_XATTR is not set
-# CONFIG_EXT2_FS_XIP is not set
-# CONFIG_EXT3_FS is not set
-# CONFIG_EXT4DEV_FS is not set
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-CONFIG_FS_POSIX_ACL=y
-# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
-# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
-CONFIG_INOTIFY=y
-CONFIG_INOTIFY_USER=y
-# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-CONFIG_FUSE_FS=y
-CONFIG_GENERIC_ACL=y
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_PROC_KCORE=y
-CONFIG_PROC_SYSCTL=y
-CONFIG_SYSFS=y
-CONFIG_TMPFS=y
-CONFIG_TMPFS_POSIX_ACL=y
-# CONFIG_HUGETLB_PAGE is not set
-CONFIG_RAMFS=y
-CONFIG_CONFIGFS_FS=y
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_ECRYPT_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
-CONFIG_NFS_FS=y
-# CONFIG_NFS_V3 is not set
-# CONFIG_NFS_V4 is not set
-# CONFIG_NFS_DIRECTIO is not set
-CONFIG_NFSD=y
-# CONFIG_NFSD_V3 is not set
-# CONFIG_NFSD_TCP is not set
-CONFIG_ROOT_NFS=y
-CONFIG_LOCKD=y
-CONFIG_EXPORTFS=y
-CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=y
-# CONFIG_RPCSEC_GSS_KRB5 is not set
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-# CONFIG_9P_FS is not set
-
-#
-# Partition Types
-#
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_MSDOS_PARTITION=y
-
-#
-# Native Language Support
-#
-# CONFIG_NLS is not set
-
-#
-# Distributed Lock Manager
-#
-CONFIG_DLM=y
-CONFIG_DLM_TCP=y
-# CONFIG_DLM_SCTP is not set
-# CONFIG_DLM_DEBUG is not set
-
-#
-# Profiling support
-#
-# CONFIG_PROFILING is not set
-
-#
-# Kernel hacking
-#
-CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-# CONFIG_PRINTK_TIME is not set
-CONFIG_ENABLE_MUST_CHECK=y
-# CONFIG_MAGIC_SYSRQ is not set
-# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
-# CONFIG_HEADERS_CHECK is not set
-# CONFIG_DEBUG_KERNEL is not set
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_CROSSCOMPILE=y
-CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
-
-#
-# Security options
-#
-CONFIG_KEYS=y
-CONFIG_KEYS_DEBUG_PROC_KEYS=y
-# CONFIG_SECURITY is not set
-
-#
-# Cryptographic options
-#
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_ALGAPI=y
-CONFIG_CRYPTO_BLKCIPHER=y
-CONFIG_CRYPTO_HASH=y
-CONFIG_CRYPTO_MANAGER=y
-CONFIG_CRYPTO_HMAC=y
-CONFIG_CRYPTO_XCBC=y
-CONFIG_CRYPTO_NULL=y
-CONFIG_CRYPTO_MD4=y
-CONFIG_CRYPTO_MD5=y
-CONFIG_CRYPTO_SHA1=y
-CONFIG_CRYPTO_SHA256=y
-CONFIG_CRYPTO_SHA512=y
-CONFIG_CRYPTO_WP512=y
-CONFIG_CRYPTO_TGR192=y
-CONFIG_CRYPTO_GF128MUL=y
-CONFIG_CRYPTO_ECB=y
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_PCBC=y
-CONFIG_CRYPTO_LRW=y
-CONFIG_CRYPTO_DES=y
-CONFIG_CRYPTO_FCRYPT=y
-CONFIG_CRYPTO_BLOWFISH=y
-CONFIG_CRYPTO_TWOFISH=y
-CONFIG_CRYPTO_TWOFISH_COMMON=y
-CONFIG_CRYPTO_SERPENT=y
-CONFIG_CRYPTO_AES=y
-CONFIG_CRYPTO_CAST5=y
-CONFIG_CRYPTO_CAST6=y
-CONFIG_CRYPTO_TEA=y
-CONFIG_CRYPTO_ARC4=y
-CONFIG_CRYPTO_KHAZAD=y
-CONFIG_CRYPTO_ANUBIS=y
-CONFIG_CRYPTO_DEFLATE=y
-CONFIG_CRYPTO_MICHAEL_MIC=y
-CONFIG_CRYPTO_CRC32C=y
-CONFIG_CRYPTO_CAMELLIA=y
-
-#
-# Hardware crypto devices
-#
-
-#
-# Library routines
-#
-CONFIG_BITREVERSE=y
-# CONFIG_CRC_CCITT is not set
-CONFIG_CRC16=y
-CONFIG_CRC32=y
-CONFIG_LIBCRC32C=y
-CONFIG_ZLIB_INFLATE=y
-CONFIG_ZLIB_DEFLATE=y
-CONFIG_PLIST=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
CONFIG_PNX8550_JBS=y
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
CONFIG_PNX8550_STB810=y
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_MIPS_SEAD is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
-# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_MIPS_SEAD is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
-# CONFIG_MOMENCO_OCELOT is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_DDB5477 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
CONFIG_WR_PPMC=y
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_WR_PPMC is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MOMENCO_OCELOT is not set
-# CONFIG_MOMENCO_OCELOT_G is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
+++ /dev/null
-#
-# Makefile for Momentum's Ocelot board.
-#
-
-obj-y += irq.o ocelot-platform.o prom.o reset.o setup.o
-
-obj-$(CONFIG_KGDB) += dbg_io.o
+++ /dev/null
-
-#include <asm/serial.h> /* For the serial port location and base baud */
-
-/* --- CONFIG --- */
-
-typedef unsigned char uint8;
-typedef unsigned int uint32;
-
-/* --- END OF CONFIG --- */
-
-#define UART16550_BAUD_2400 2400
-#define UART16550_BAUD_4800 4800
-#define UART16550_BAUD_9600 9600
-#define UART16550_BAUD_19200 19200
-#define UART16550_BAUD_38400 38400
-#define UART16550_BAUD_57600 57600
-#define UART16550_BAUD_115200 115200
-
-#define UART16550_PARITY_NONE 0
-#define UART16550_PARITY_ODD 0x08
-#define UART16550_PARITY_EVEN 0x18
-#define UART16550_PARITY_MARK 0x28
-#define UART16550_PARITY_SPACE 0x38
-
-#define UART16550_DATA_5BIT 0x0
-#define UART16550_DATA_6BIT 0x1
-#define UART16550_DATA_7BIT 0x2
-#define UART16550_DATA_8BIT 0x3
-
-#define UART16550_STOP_1BIT 0x0
-#define UART16550_STOP_2BIT 0x4
-
-/* ----------------------------------------------------- */
-
-/* === CONFIG === */
-
-/* [jsun] we use the second serial port for kdb */
-#define BASE OCELOT_SERIAL1_BASE
-#define MAX_BAUD OCELOT_BASE_BAUD
-
-/* === END OF CONFIG === */
-
-#define REG_OFFSET 4
-
-/* register offset */
-#define OFS_RCV_BUFFER 0
-#define OFS_TRANS_HOLD 0
-#define OFS_SEND_BUFFER 0
-#define OFS_INTR_ENABLE (1*REG_OFFSET)
-#define OFS_INTR_ID (2*REG_OFFSET)
-#define OFS_DATA_FORMAT (3*REG_OFFSET)
-#define OFS_LINE_CONTROL (3*REG_OFFSET)
-#define OFS_MODEM_CONTROL (4*REG_OFFSET)
-#define OFS_RS232_OUTPUT (4*REG_OFFSET)
-#define OFS_LINE_STATUS (5*REG_OFFSET)
-#define OFS_MODEM_STATUS (6*REG_OFFSET)
-#define OFS_RS232_INPUT (6*REG_OFFSET)
-#define OFS_SCRATCH_PAD (7*REG_OFFSET)
-
-#define OFS_DIVISOR_LSB (0*REG_OFFSET)
-#define OFS_DIVISOR_MSB (1*REG_OFFSET)
-
-
-/* memory-mapped read/write of the port */
-#define UART16550_READ(y) (*((volatile uint8*)(BASE + y)))
-#define UART16550_WRITE(y, z) ((*((volatile uint8*)(BASE + y))) = z)
-
-void debugInit(uint32 baud, uint8 data, uint8 parity, uint8 stop)
-{
- /* disable interrupts */
- UART16550_WRITE(OFS_INTR_ENABLE, 0);
-
- /* set up baud rate */
- {
- uint32 divisor;
-
- /* set DIAB bit */
- UART16550_WRITE(OFS_LINE_CONTROL, 0x80);
-
- /* set divisor */
- divisor = MAX_BAUD / baud;
- UART16550_WRITE(OFS_DIVISOR_LSB, divisor & 0xff);
- UART16550_WRITE(OFS_DIVISOR_MSB, (divisor & 0xff00) >> 8);
-
- /* clear DIAB bit */
- UART16550_WRITE(OFS_LINE_CONTROL, 0x0);
- }
-
- /* set data format */
- UART16550_WRITE(OFS_DATA_FORMAT, data | parity | stop);
-}
-
-static int remoteDebugInitialized = 0;
-
-uint8 getDebugChar(void)
-{
- if (!remoteDebugInitialized) {
- remoteDebugInitialized = 1;
- debugInit(UART16550_BAUD_38400,
- UART16550_DATA_8BIT,
- UART16550_PARITY_NONE, UART16550_STOP_1BIT);
- }
-
- while ((UART16550_READ(OFS_LINE_STATUS) & 0x1) == 0);
- return UART16550_READ(OFS_RCV_BUFFER);
-}
-
-
-int putDebugChar(uint8 byte)
-{
- if (!remoteDebugInitialized) {
- remoteDebugInitialized = 1;
- debugInit(UART16550_BAUD_38400,
- UART16550_DATA_8BIT,
- UART16550_PARITY_NONE, UART16550_STOP_1BIT);
- }
-
- while ((UART16550_READ(OFS_LINE_STATUS) & 0x20) == 0);
- UART16550_WRITE(OFS_SEND_BUFFER, byte);
- return 1;
-}
+++ /dev/null
-/*
- * Copyright (C) 2000 RidgeRun, Inc.
- * Author: RidgeRun, Inc.
- * glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com
- *
- * Copyright 2001 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- * Copyright (C) 2000, 2001, 2003 Ralf Baechle (ralf@gnu.org)
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- */
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/kernel_stat.h>
-#include <linux/module.h>
-#include <linux/signal.h>
-#include <linux/sched.h>
-#include <linux/types.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/timex.h>
-#include <linux/slab.h>
-#include <linux/random.h>
-#include <linux/bitops.h>
-#include <asm/bootinfo.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/irq_cpu.h>
-#include <asm/mipsregs.h>
-#include <asm/system.h>
-
-asmlinkage void plat_irq_dispatch(void)
-{
- unsigned int pending = read_c0_status() & read_c0_cause();
-
- if (pending & STATUSF_IP2) /* int0 hardware line */
- do_IRQ(2);
- else if (pending & STATUSF_IP3) /* int1 hardware line */
- do_IRQ(3);
- else if (pending & STATUSF_IP4) /* int2 hardware line */
- do_IRQ(4);
- else if (pending & STATUSF_IP5) /* int3 hardware line */
- do_IRQ(5);
- else if (pending & STATUSF_IP6) /* int4 hardware line */
- do_IRQ(6);
- else if (pending & STATUSF_IP7) /* cpu timer */
- do_IRQ(7);
- else {
- /*
- * Now look at the extended interrupts
- */
- pending = (read_c0_cause() & (read_c0_intcontrol() << 8)) >> 16;
-
- if (pending & STATUSF_IP8) /* int6 hardware line */
- do_IRQ(8);
- else if (pending & STATUSF_IP9) /* int7 hardware line */
- do_IRQ(9);
- else if (pending & STATUSF_IP10) /* int8 hardware line */
- do_IRQ(10);
- else if (pending & STATUSF_IP11) /* int9 hardware line */
- do_IRQ(11);
- }
-}
-
-void __init arch_init_irq(void)
-{
- /*
- * Clear all of the interrupts while we change the able around a bit.
- * int-handler is not on bootstrap
- */
- clear_c0_status(ST0_IM);
- local_irq_disable();
-
- mips_cpu_irq_init();
- rm7k_cpu_irq_init();
-}
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2007 Ralf Baechle (ralf@linux-mips.org)
- *
- * A NS16552 DUART with a 20MHz crystal.
- *
- */
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/serial_8250.h>
-
-#define OCELOT_UART_FLAGS (UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP)
-
-static struct plat_serial8250_port uart8250_data[] = {
- {
- .mapbase = 0xe0001020,
- .irq = 4,
- .uartclk = 20000000,
- .iotype = UPIO_MEM,
- .flags = OCELOT_UART_FLAGS,
- .regshift = 2,
- },
- { },
-};
-
-static struct platform_device uart8250_device = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM,
- .dev = {
- .platform_data = uart8250_data,
- },
-};
-
-static int __init uart8250_init(void)
-{
- return platform_device_register(&uart8250_device);
-}
-
-module_init(uart8250_init);
-
-MODULE_AUTHOR("Ralf Baechle <ralf@linux-mips.org>");
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("8250 UART probe driver for the Momenco Ocelot");
+++ /dev/null
-/*
- * Ocelot Board Register Definitions
- *
- * (C) 2001 Red Hat, Inc.
- *
- * GPL'd
- */
-#ifndef __MOMENCO_OCELOT_PLD_H__
-#define __MOMENCO_OCELOT_PLD_H__
-
-#define OCELOT_CS0_ADDR (0xe0020000)
-
-#define OCELOT_REG_BOARDREV (0)
-#define OCELOT_REG_PLD1_ID (1)
-#define OCELOT_REG_PLD2_ID (2)
-#define OCELOT_REG_RESET_STATUS (3)
-#define OCELOT_REG_BOARD_STATUS (4)
-#define OCELOT_REG_CPCI_ID (5)
-#define OCELOT_REG_I2C_CTRL (8)
-#define OCELOT_REG_EEPROM_MODE (9)
-#define OCELOT_REG_INTMASK (10)
-#define OCELOT_REG_INTSTATUS (11)
-#define OCELOT_REG_INTSET (12)
-#define OCELOT_REG_INTCLR (13)
-
-#define OCELOT_PLD_WRITE(x, y) writeb(x, OCELOT_CS0_ADDR + OCELOT_REG_##y)
-#define OCELOT_PLD_READ(x) readb(OCELOT_CS0_ADDR + OCELOT_REG_##x)
-
-
-#endif /* __MOMENCO_OCELOT_PLD_H__ */
+++ /dev/null
-/*
- * Copyright 2001 MontaVista Software Inc.
- * Author: jsun@mvista.com or jsun@junsun.net
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/bootmem.h>
-
-#include <asm/addrspace.h>
-#include <asm/bootinfo.h>
-#include <asm/pmon.h>
-
-struct callvectors* debug_vectors;
-
-extern unsigned long gt64120_base;
-
-const char *get_system_type(void)
-{
- return "Momentum Ocelot";
-}
-
-/* [jsun@junsun.net] PMON passes arguments in C main() style */
-void __init prom_init(void)
-{
- int argc = fw_arg0;
- char **arg = (char **) fw_arg1;
- char **env = (char **) fw_arg2;
- struct callvectors *cv = (struct callvectors *) fw_arg3;
- int i;
-
- /* save the PROM vectors for debugging use */
- debug_vectors = cv;
-
- /* arg[0] is "g", the rest is boot parameters */
- arcs_cmdline[0] = '\0';
- for (i = 1; i < argc; i++) {
- if (strlen(arcs_cmdline) + strlen(arg[i] + 1)
- >= sizeof(arcs_cmdline))
- break;
- strcat(arcs_cmdline, arg[i]);
- strcat(arcs_cmdline, " ");
- }
-
- mips_machgroup = MACH_GROUP_MOMENCO;
- mips_machtype = MACH_MOMENCO_OCELOT;
-
- while (*env) {
- if (strncmp("gtbase", *env, 6) == 0) {
- gt64120_base = simple_strtol(*env + strlen("gtbase="),
- NULL, 16);
- break;
- }
- *env++;
- }
-
- debug_vectors->printf("Booting Linux kernel...\n");
-
- /* All the boards have at least 64MiB. If there's more, we
- detect and register it later */
- add_memory_region(0, 64 << 20, BOOT_MEM_RAM);
-}
-
-void __init prom_free_prom_memory(void)
-{
-}
+++ /dev/null
-/*
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * Copyright (C) 1997, 2001 Ralf Baechle
- * Copyright 2001 MontaVista Software Inc.
- * Author: jsun@mvista.com or jsun@junsun.net
- */
-#include <linux/sched.h>
-#include <linux/mm.h>
-#include <asm/io.h>
-#include <asm/pgtable.h>
-#include <asm/processor.h>
-#include <asm/reboot.h>
-#include <asm/system.h>
-#include <linux/delay.h>
-
-void momenco_ocelot_restart(char *command)
-{
- void *nvram = ioremap_nocache(0x2c807000, 0x1000);
-
- if (!nvram) {
- printk(KERN_NOTICE "ioremap of reset register failed\n");
- return;
- }
- writeb(0x84, nvram + 0xff7); /* Ask the NVRAM/RTC/watchdog chip to
- assert reset in 1/16 second */
- mdelay(10+(1000/16));
- iounmap(nvram);
- printk(KERN_NOTICE "Watchdog reset failed\n");
-}
-
-void momenco_ocelot_halt(void)
-{
- printk(KERN_NOTICE "\n** You can safely turn off the power\n");
- while (1)
- __asm__(".set\tmips3\n\t"
- "wait\n\t"
- ".set\tmips0");
-}
-
-void momenco_ocelot_power_off(void)
-{
- momenco_ocelot_halt();
-}
+++ /dev/null
-/*
- * setup.c
- *
- * BRIEF MODULE DESCRIPTION
- * Momentum Computer Ocelot (CP7000) - board dependent boot routines
- *
- * Copyright (C) 1996, 1997, 2001, 06 Ralf Baechle (ralf@linux-mips.org)
- * Copyright (C) 2000 RidgeRun, Inc.
- * Copyright (C) 2001 Red Hat, Inc.
- * Copyright (C) 2002 Momentum Computer
- *
- * Author: RidgeRun, Inc.
- * glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com
- *
- * Copyright 2001 MontaVista Software Inc.
- * Author: jsun@mvista.com or jsun@junsun.net
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- */
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/mm.h>
-#include <linux/swap.h>
-#include <linux/ioport.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/pci.h>
-#include <linux/timex.h>
-#include <linux/vmalloc.h>
-#include <linux/pm.h>
-
-#include <asm/time.h>
-#include <asm/bootinfo.h>
-#include <asm/page.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/pci.h>
-#include <asm/processor.h>
-#include <asm/reboot.h>
-#include <asm/traps.h>
-#include <linux/bootmem.h>
-#include <linux/initrd.h>
-#include <asm/gt64120.h>
-#include "ocelot_pld.h"
-
-unsigned long gt64120_base = KSEG1ADDR(GT_DEF_BASE);
-
-/* These functions are used for rebooting or halting the machine*/
-extern void momenco_ocelot_restart(char *command);
-extern void momenco_ocelot_halt(void);
-extern void momenco_ocelot_power_off(void);
-
-extern void momenco_ocelot_irq_setup(void);
-
-static char reset_reason;
-
-#define ENTRYLO(x) ((pte_val(pfn_pte((x) >> PAGE_SHIFT, PAGE_KERNEL_UNCACHED)) >> 6)|1)
-
-static void __init setup_l3cache(unsigned long size);
-
-/* setup code for a handoff from a version 1 PMON 2000 PROM */
-static void PMON_v1_setup(void)
-{
- /* A wired TLB entry for the GT64120A and the serial port. The
- GT64120A is going to be hit on every IRQ anyway - there's
- absolutely no point in letting it be a random TLB entry, as
- it'll just cause needless churning of the TLB. And we use
- the other half for the serial port, which is just a PITA
- otherwise :)
-
- Device Physical Virtual
- GT64120 Internal Regs 0x24000000 0xe0000000
- UARTs (CS2) 0x2d000000 0xe0001000
- */
- add_wired_entry(ENTRYLO(0x24000000), ENTRYLO(0x2D000000), 0xe0000000, PM_4K);
-
- /* Also a temporary entry to let us talk to the Ocelot PLD and NVRAM
- in the CS[012] region. We can't use ioremap() yet. The NVRAM
- is a ST M48T37Y, which includes NVRAM, RTC, and Watchdog functions.
-
- Ocelot PLD (CS0) 0x2c000000 0xe0020000
- NVRAM 0x2c800000 0xe0030000
- */
-
- add_temporary_entry(ENTRYLO(0x2C000000), ENTRYLO(0x2d000000), 0xe0020000, PM_64K);
-
- /* Relocate the CS3/BootCS region */
- GT_WRITE(GT_CS3BOOTLD_OFS, 0x2f000000 >> 21);
-
- /* Relocate CS[012] */
- GT_WRITE(GT_CS20LD_OFS, 0x2c000000 >> 21);
-
- /* Relocate the GT64120A itself... */
- GT_WRITE(GT_ISD_OFS, 0x24000000 >> 21);
- mb();
- gt64120_base = 0xe0000000;
-
- /* ...and the PCI0 view of it. */
- GT_WRITE(GT_PCI0_CFGADDR_OFS, 0x80000020);
- GT_WRITE(GT_PCI0_CFGDATA_OFS, 0x24000000);
- GT_WRITE(GT_PCI0_CFGADDR_OFS, 0x80000024);
- GT_WRITE(GT_PCI0_CFGDATA_OFS, 0x24000001);
-}
-
-/* setup code for a handoff from a version 2 PMON 2000 PROM */
-void PMON_v2_setup()
-{
- /* A wired TLB entry for the GT64120A and the serial port. The
- GT64120A is going to be hit on every IRQ anyway - there's
- absolutely no point in letting it be a random TLB entry, as
- it'll just cause needless churning of the TLB. And we use
- the other half for the serial port, which is just a PITA
- otherwise :)
-
- Device Physical Virtual
- GT64120 Internal Regs 0xf4000000 0xe0000000
- UARTs (CS2) 0xfd000000 0xe0001000
- */
- add_wired_entry(ENTRYLO(0xf4000000), ENTRYLO(0xfD000000), 0xe0000000, PM_4K);
-
- /* Also a temporary entry to let us talk to the Ocelot PLD and NVRAM
- in the CS[012] region. We can't use ioremap() yet. The NVRAM
- is a ST M48T37Y, which includes NVRAM, RTC, and Watchdog functions.
-
- Ocelot PLD (CS0) 0xfc000000 0xe0020000
- NVRAM 0xfc800000 0xe0030000
- */
- add_temporary_entry(ENTRYLO(0xfC000000), ENTRYLO(0xfd000000), 0xe0020000, PM_64K);
-
- gt64120_base = 0xe0000000;
-}
-
-void __init plat_mem_setup(void)
-{
- void (*l3func)(unsigned long)=KSEG1ADDR(&setup_l3cache);
- unsigned int tmpword;
-
- _machine_restart = momenco_ocelot_restart;
- _machine_halt = momenco_ocelot_halt;
- pm_power_off = momenco_ocelot_power_off;
-
- /*
- * initrd_start = (unsigned long)ocelot_initrd_start;
- * initrd_end = (unsigned long)ocelot_initrd_start + (ulong)ocelot_initrd_size;
- * initrd_below_start_ok = 1;
- */
-
- /* do handoff reconfiguration */
- if (gt64120_base == KSEG1ADDR(GT_DEF_BASE))
- PMON_v1_setup();
- else
- PMON_v2_setup();
-
- /* Turn off the Bit-Error LED */
- OCELOT_PLD_WRITE(0x80, INTCLR);
-
- /* Relocate all the PCI1 stuff, not that we use it */
- GT_WRITE(GT_PCI1IOLD_OFS, 0x30000000 >> 21);
- GT_WRITE(GT_PCI1M0LD_OFS, 0x32000000 >> 21);
- GT_WRITE(GT_PCI1M1LD_OFS, 0x34000000 >> 21);
-
- /* Relocate PCI0 I/O and Mem0 */
- GT_WRITE(GT_PCI0IOLD_OFS, 0x20000000 >> 21);
- GT_WRITE(GT_PCI0M0LD_OFS, 0x22000000 >> 21);
-
- /* Relocate PCI0 Mem1 */
- GT_WRITE(GT_PCI0M1LD_OFS, 0x36000000 >> 21);
-
- /* For the initial programming, we assume 512MB configuration */
- /* Relocate the CPU's view of the RAM... */
- GT_WRITE(GT_SCS10LD_OFS, 0);
- GT_WRITE(GT_SCS10HD_OFS, 0x0fe00000 >> 21);
- GT_WRITE(GT_SCS32LD_OFS, 0x10000000 >> 21);
- GT_WRITE(GT_SCS32HD_OFS, 0x0fe00000 >> 21);
-
- GT_WRITE(GT_SCS1LD_OFS, 0xff);
- GT_WRITE(GT_SCS1HD_OFS, 0x00);
- GT_WRITE(GT_SCS0LD_OFS, 0);
- GT_WRITE(GT_SCS0HD_OFS, 0xff);
- GT_WRITE(GT_SCS3LD_OFS, 0xff);
- GT_WRITE(GT_SCS3HD_OFS, 0x00);
- GT_WRITE(GT_SCS2LD_OFS, 0);
- GT_WRITE(GT_SCS2HD_OFS, 0xff);
-
- /* ...and the PCI0 view of it. */
- GT_WRITE(GT_PCI0_CFGADDR_OFS, 0x80000010);
- GT_WRITE(GT_PCI0_CFGDATA_OFS, 0x00000000);
- GT_WRITE(GT_PCI0_CFGADDR_OFS, 0x80000014);
- GT_WRITE(GT_PCI0_CFGDATA_OFS, 0x10000000);
- GT_WRITE(GT_PCI0_BS_SCS10_OFS, 0x0ffff000);
- GT_WRITE(GT_PCI0_BS_SCS32_OFS, 0x0ffff000);
-
- tmpword = OCELOT_PLD_READ(BOARDREV);
- if (tmpword < 26)
- printk("Momenco Ocelot: Board Assembly Rev. %c\n", 'A'+tmpword);
- else
- printk("Momenco Ocelot: Board Assembly Revision #0x%x\n", tmpword);
-
- tmpword = OCELOT_PLD_READ(PLD1_ID);
- printk("PLD 1 ID: %d.%d\n", tmpword>>4, tmpword&15);
- tmpword = OCELOT_PLD_READ(PLD2_ID);
- printk("PLD 2 ID: %d.%d\n", tmpword>>4, tmpword&15);
- tmpword = OCELOT_PLD_READ(RESET_STATUS);
- printk("Reset reason: 0x%x\n", tmpword);
- reset_reason = tmpword;
- OCELOT_PLD_WRITE(0xff, RESET_STATUS);
-
- tmpword = OCELOT_PLD_READ(BOARD_STATUS);
- printk("Board Status register: 0x%02x\n", tmpword);
- printk(" - User jumper: %s\n", (tmpword & 0x80)?"installed":"absent");
- printk(" - Boot flash write jumper: %s\n", (tmpword&0x40)?"installed":"absent");
- printk(" - Tulip PHY %s connected\n", (tmpword&0x10)?"is":"not");
- printk(" - L3 Cache size: %d MiB\n", (1<<((tmpword&12) >> 2))&~1);
- printk(" - SDRAM size: %d MiB\n", 1<<(6+(tmpword&3)));
-
- if (tmpword&12)
- l3func((1<<(((tmpword&12) >> 2)+20)));
-
- switch(tmpword &3) {
- case 3:
- /* 512MiB */
- /* Decoders are allready set -- just add the
- * appropriate region */
- add_memory_region( 0x40<<20, 0xC0<<20, BOOT_MEM_RAM);
- add_memory_region(0x100<<20, 0x100<<20, BOOT_MEM_RAM);
- break;
- case 2:
- /* 256MiB -- two banks of 128MiB */
- GT_WRITE(GT_SCS10HD_OFS, 0x07e00000 >> 21);
- GT_WRITE(GT_SCS32LD_OFS, 0x08000000 >> 21);
- GT_WRITE(GT_SCS32HD_OFS, 0x0fe00000 >> 21);
-
- GT_WRITE(GT_SCS0HD_OFS, 0x7f);
- GT_WRITE(GT_SCS2LD_OFS, 0x80);
- GT_WRITE(GT_SCS2HD_OFS, 0xff);
-
- /* reconfigure the PCI0 interface view of memory */
- GT_WRITE(GT_PCI0_CFGADDR_OFS, 0x80000014);
- GT_WRITE(GT_PCI0_CFGDATA_OFS, 0x08000000);
- GT_WRITE(GT_PCI0_BS_SCS10_OFS, 0x0ffff000);
- GT_WRITE(GT_PCI0_BS_SCS32_OFS, 0x0ffff000);
-
- add_memory_region(0x40<<20, 0x40<<20, BOOT_MEM_RAM);
- add_memory_region(0x80<<20, 0x80<<20, BOOT_MEM_RAM);
- break;
- case 1:
- /* 128MiB -- 64MiB per bank */
- GT_WRITE(GT_SCS10HD_OFS, 0x03e00000 >> 21);
- GT_WRITE(GT_SCS32LD_OFS, 0x04000000 >> 21);
- GT_WRITE(GT_SCS32HD_OFS, 0x07e00000 >> 21);
-
- GT_WRITE(GT_SCS0HD_OFS, 0x3f);
- GT_WRITE(GT_SCS2LD_OFS, 0x40);
- GT_WRITE(GT_SCS2HD_OFS, 0x7f);
-
- /* reconfigure the PCI0 interface view of memory */
- GT_WRITE(GT_PCI0_CFGADDR_OFS, 0x80000014);
- GT_WRITE(GT_PCI0_CFGDATA_OFS, 0x04000000);
- GT_WRITE(GT_PCI0_BS_SCS10_OFS, 0x03fff000);
- GT_WRITE(GT_PCI0_BS_SCS32_OFS, 0x03fff000);
-
- /* add the appropriate region */
- add_memory_region(0x40<<20, 0x40<<20, BOOT_MEM_RAM);
- break;
- case 0:
- /* 64MiB */
- GT_WRITE(GT_SCS10HD_OFS, 0x01e00000 >> 21);
- GT_WRITE(GT_SCS32LD_OFS, 0x02000000 >> 21);
- GT_WRITE(GT_SCS32HD_OFS, 0x03e00000 >> 21);
-
- GT_WRITE(GT_SCS0HD_OFS, 0x1f);
- GT_WRITE(GT_SCS2LD_OFS, 0x20);
- GT_WRITE(GT_SCS2HD_OFS, 0x3f);
-
- /* reconfigure the PCI0 interface view of memory */
- GT_WRITE(GT_PCI0_CFGADDR_OFS, 0x80000014);
- GT_WRITE(GT_PCI0_CFGDATA_OFS, 0x04000000);
- GT_WRITE(GT_PCI0_BS_SCS10_OFS, 0x01fff000);
- GT_WRITE(GT_PCI0_BS_SCS32_OFS, 0x01fff000);
-
- break;
- }
-
- /* Fix up the DiskOnChip mapping */
- GT_WRITE(GT_DEV_B3_OFS, 0xfef73);
-}
-
-extern int rm7k_tcache_enabled;
-/*
- * This runs in KSEG1. See the verbiage in rm7k.c::probe_scache()
- */
-#define Page_Invalidate_T 0x16
-static void __init setup_l3cache(unsigned long size)
-{
- int register i;
- unsigned long tmp;
-
- printk("Enabling L3 cache...");
-
- /* Enable the L3 cache in the GT64120A's CPU Configuration register */
- tmp = GT_READ(GT_CPU_OFS);
- GT_WRITE(GT_CPU_OFS, tmp | (1<<14));
-
- /* Enable the L3 cache in the CPU */
- set_c0_config(1<<12 /* CONF_TE */);
-
- /* Clear the cache */
- write_c0_taglo(0);
- write_c0_taghi(0);
-
- for (i=0; i < size; i+= 4096) {
- __asm__ __volatile__ (
- ".set noreorder\n\t"
- ".set mips3\n\t"
- "cache %1, (%0)\n\t"
- ".set mips0\n\t"
- ".set reorder"
- :
- : "r" (KSEG0ADDR(i)),
- "i" (Page_Invalidate_T));
- }
-
- /* Let the RM7000 MM code know that the tertiary cache is enabled */
- rm7k_tcache_enabled = 1;
-
- printk("Done\n");
-}
-
-
-/* This needs to be one of the first initcalls, because no I/O port access
- can work before this */
-
-static int io_base_ioremap(void)
-{
- void *io_remap_range = ioremap(GT_PCI_IO_BASE, GT_PCI_IO_SIZE);
-
- if (!io_remap_range) {
- panic("Could not ioremap I/O port range");
- }
- set_io_port_base(io_remap_range - GT_PCI_IO_BASE);
-
- return 0;
-}
-
-module_init(io_base_ioremap);
obj-$(CONFIG_SOC_PNX8550) += fixup-pnx8550.o ops-pnx8550.o
obj-$(CONFIG_LEMOTE_FULONG) += fixup-lm2e.o ops-bonito64.o
obj-$(CONFIG_MIPS_MALTA) += fixup-malta.o
-obj-$(CONFIG_MOMENCO_OCELOT) += fixup-ocelot.o pci-ocelot.o
obj-$(CONFIG_PMC_MSP7120_GW) += fixup-pmcmsp.o ops-pmcmsp.o
obj-$(CONFIG_PMC_MSP7120_EVAL) += fixup-pmcmsp.o ops-pmcmsp.o
obj-$(CONFIG_PMC_MSP7120_FPGA) += fixup-pmcmsp.o ops-pmcmsp.o
+++ /dev/null
-/*
- * Copyright 2001 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- *
- * arch/mips/gt64120/momenco_ocelot/pci.c
- * Board-specific PCI routines for gt64120 controller.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <asm/pci.h>
-
-
-void __devinit pcibios_fixup_bus(struct pci_bus *bus)
-{
- struct pci_bus *current_bus = bus;
- struct pci_dev *devices;
- struct list_head *devices_link;
- u16 cmd;
-
- list_for_each(devices_link, &(current_bus->devices)) {
-
- devices = pci_dev_b(devices_link);
- if (devices == NULL)
- continue;
-
- if (PCI_SLOT(devices->devfn) == 1) {
- /*
- * Slot 1 is primary ether port, i82559
- * we double-check against that assumption
- */
- if ((devices->vendor != 0x8086) ||
- (devices->device != 0x1209)) {
- panic("pcibios_fixup_bus: found "
- "unexpected PCI device in slot 1.");
- }
- devices->irq = 2; /* irq_nr is 2 for INT0 */
- } else if (PCI_SLOT(devices->devfn) == 2) {
- /*
- * Slot 2 is secondary ether port, i21143
- * we double-check against that assumption
- */
- if ((devices->vendor != 0x1011) ||
- (devices->device != 0x19)) {
- panic("galileo_pcibios_fixup_bus: "
- "found unexpected PCI device in slot 2.");
- }
- devices->irq = 3; /* irq_nr is 3 for INT1 */
- } else if (PCI_SLOT(devices->devfn) == 4) {
- /* PMC Slot 1 */
- devices->irq = 8; /* irq_nr is 8 for INT6 */
- } else if (PCI_SLOT(devices->devfn) == 5) {
- /* PMC Slot 1 */
- devices->irq = 9; /* irq_nr is 9 for INT7 */
- } else {
- /* We don't have assign interrupts for other devices. */
- devices->irq = 0xff;
- }
-
- /* Assign an interrupt number for the device */
- bus->ops->write_byte(devices, PCI_INTERRUPT_LINE,
- devices->irq);
-
- /* enable master */
- bus->ops->read_word(devices, PCI_COMMAND, &cmd);
- cmd |= PCI_COMMAND_MASTER;
- bus->ops->write_word(devices, PCI_COMMAND, cmd);
- }
-}
+++ /dev/null
-/*
- * BRIEF MODULE DESCRIPTION
- * Galileo Evaluation Boards PCI support.
- *
- * The general-purpose functions to read/write and configure the GT64120A's
- * PCI registers (function names start with pci0 or pci1) are either direct
- * copies of functions written by Galileo Technology, or are modifications
- * of their functions to work with Linux 2.4 vs Linux 2.2. These functions
- * are Copyright - Galileo Technology.
- *
- * Other functions are derived from other MIPS PCI implementations, or were
- * written by RidgeRun, Inc, Copyright (C) 2000 RidgeRun, Inc.
- * glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com
- *
- * Copyright 2001 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-#include <linux/init.h>
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/kernel.h>
-#include <linux/slab.h>
-#include <linux/cache.h>
-#include <asm/pci.h>
-#include <asm/io.h>
-#include <asm/gt64120.h>
-
-static inline unsigned int pci0ReadConfigReg(unsigned int offset)
-{
- unsigned int DataForRegCf8;
- unsigned int data;
-
- DataForRegCf8 = ((PCI_SLOT(device->devfn) << 11) |
- (PCI_FUNC(device->devfn) << 8) |
- (offset & ~0x3)) | 0x80000000;
- GT_WRITE(GT_PCI0_CFGADDR_OFS, DataForRegCf8);
- GT_READ(GT_PCI0_CFGDATA_OFS, &data);
-
- return data;
-}
-
-static inline void pci0WriteConfigReg(unsigned int offset, unsigned int data)
-{
- unsigned int DataForRegCf8;
-
- DataForRegCf8 = ((PCI_SLOT(device->devfn) << 11) |
- (PCI_FUNC(device->devfn) << 8) |
- (offset & ~0x3)) | 0x80000000;
- GT_WRITE(GT_PCI0_CFGADDR_OFS, DataForRegCf8);
- GT_WRITE(GT_PCI0_CFGDATA_OFS, data);
-}
-
-static struct resource ocelot_mem_resource = {
- .start = GT_PCI_MEM_BASE,
- .end = GT_PCI_MEM_BASE + GT_PCI_MEM_BASE - 1,
-};
-
-static struct resource ocelot_io_resource = {
- .start = GT_PCI_IO_BASE,
- .end = GT_PCI_IO_BASE + GT_PCI_IO_SIZE - 1,
-};
-
-static struct pci_controller ocelot_pci_controller = {
- .pci_ops = gt64xxx_pci0_ops,
- .mem_resource = &ocelot_mem_resource,
- .io_resource = &ocelot_io_resource,
-};
-
-static int __init ocelot_pcibios_init(void)
-{
- u32 tmp;
-
- GT_READ(GT_PCI0_CMD_OFS, &tmp);
- GT_READ(GT_PCI0_BARE_OFS, &tmp);
-
- /*
- * You have to enable bus mastering to configure any other
- * card on the bus.
- */
- tmp = pci0ReadConfigReg(PCI_COMMAND);
- tmp |= PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER | PCI_COMMAND_SERR;
- pci0WriteConfigReg(PCI_COMMAND, tmp);
-
- register_pci_controller(&ocelot_pci_controller);
-}
-
-arch_initcall(ocelot_pcibios_init);
#endif /* CONFIG_MTD_DOCPROBE_HIGH */
#elif defined(__PPC__)
0xe4000000,
-#elif defined(CONFIG_MOMENCO_OCELOT)
- 0x2f000000,
- 0xff000000,
#elif defined(CONFIG_MOMENCO_OCELOT_G)
0xff000000,
##else
#endif /* CONFIG_MTD_DOCPROBE_HIGH */
#elif defined(__PPC__)
0xe4000000,
-#elif defined(CONFIG_MOMENCO_OCELOT)
- 0x2f000000,
- 0xff000000,
#elif defined(CONFIG_MOMENCO_OCELOT_G)
0xff000000,
#else
* exceptions.
*/
#if defined(CONFIG_BASLER_EXCITE) || defined(CONFIG_MIPS_ATLAS) || \
- defined(CONFIG_MIPS_MALTA) || defined(CONFIG_MOMENCO_OCELOT) || \
- defined(CONFIG_PMC_YOSEMITE) || defined(CONFIG_SGI_IP32) || \
- defined(CONFIG_WR_PPMC)
+ defined(CONFIG_MIPS_MALTA) || defined(CONFIG_PMC_YOSEMITE) || \
+ defined(CONFIG_SGI_IP32) || defined(CONFIG_WR_PPMC)
#define ICACHE_REFILLS_WORKAROUND_WAR 1
#endif
projects / linux-2.6-omap-h63xx.git / commitdiff