Dreamcast with a serial line terminal or a remote network
connection.
-config CF_ENABLER
- bool "Compact Flash Enabler support"
- depends on SOLUTION_ENGINE
- ---help---
- Compact Flash is a small, removable mass storage device introduced
- in 1994 originally as a PCMCIA device. If you say `Y' here, you
- compile in support for Compact Flash devices directly connected to
- a SuperH processor. A Compact Flash FAQ is available at
- <http://www.compactflash.org/faqs/faq.htm>.
-
- If your board has "Directly Connected" CompactFlash at area 5 or 6,
- you may want to enable this option. Then, you can use CF as
- primary IDE drive (only tested for SanDisk).
-
- If in doubt, select 'N'.
-
-choice
- prompt "Compact Flash Connection Area"
- depends on CF_ENABLER
- default CF_AREA6
-
-config CF_AREA5
- bool "Area5"
- help
- If your board has "Directly Connected" CompactFlash, You should
- select the area where your CF is connected to.
-
- - "Area5" if CompactFlash is connected to Area 5 (0x14000000)
- - "Area6" if it is connected to Area 6 (0x18000000)
-
- "Area6" will work for most boards.
-
-config CF_AREA6
- bool "Area6"
-
-endchoice
-
-config CF_BASE_ADDR
- hex
- depends on CF_ENABLER
- default "0xb8000000" if CF_AREA6
- default "0xb4000000" if CF_AREA5
-
source "arch/sh/drivers/pci/Kconfig"
source "drivers/pci/Kconfig"
*/
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <asm/machvec.h>
#include <mach-se/mach/se.h>
+#include <mach-se/mach/mrshpc.h>
+#include <asm/machvec.h>
#include <asm/io.h>
#include <asm/smc37c93x.h>
#include <asm/heartbeat.h>
static int __init se_devices_setup(void)
{
+ mrshpc_setup_windows();
return platform_add_devices(se_devices, ARRAY_SIZE(se_devices));
}
device_initcall(se_devices_setup);
*/
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <asm/machvec.h>
#include <mach-se/mach/se7721.h>
+#include <mach-se/mach/mrshpc.h>
+#include <asm/machvec.h>
#include <asm/io.h>
#include <asm/heartbeat.h>
static int __init se7721_devices_setup(void)
{
- return platform_add_devices(se7721_devices,
- ARRAY_SIZE(se7721_devices));
+ mrshpc_setup_windows();
+ return platform_add_devices(se7721_devices, ARRAY_SIZE(se7721_devices));
}
device_initcall(se7721_devices_setup);
#include <linux/ata_platform.h>
#include <linux/input.h>
#include <linux/smc91x.h>
+#include <mach-se/mach/se7722.h>
+#include <mach-se/mach/mrshpc.h>
#include <asm/machvec.h>
#include <asm/clock.h>
-#include <mach-se/mach/se7722.h>
#include <asm/io.h>
#include <asm/heartbeat.h>
#include <asm/sh_keysc.h>
static int __init se7722_devices_setup(void)
{
- return platform_add_devices(se7722_devices,
- ARRAY_SIZE(se7722_devices));
+ mrshpc_setup_windows();
+ return platform_add_devices(se7722_devices, ARRAY_SIZE(se7722_devices));
}
device_initcall(se7722_devices_setup);
--- /dev/null
+#ifndef __MACH_SE_MRSHPC_H
+#define __MACH_SE_MRSHPC_H
+
+#include <linux/io.h>
+
+static void __init mrshpc_setup_windows(void)
+{
+ if ((__raw_readw(MRSHPC_CSR) & 0x000c) != 0)
+ return; /* Not detected */
+
+ if ((__raw_readw(MRSHPC_CSR) & 0x0080) == 0) {
+ __raw_writew(0x0674, MRSHPC_CPWCR); /* Card Vcc is 3.3v? */
+ } else {
+ __raw_writew(0x0678, MRSHPC_CPWCR); /* Card Vcc is 5V */
+ }
+
+ /*
+ * PC-Card window open
+ * flag == COMMON/ATTRIBUTE/IO
+ */
+ /* common window open */
+ __raw_writew(0x8a84, MRSHPC_MW0CR1);
+ if((__raw_readw(MRSHPC_CSR) & 0x4000) != 0)
+ /* common mode & bus width 16bit SWAP = 1*/
+ __raw_writew(0x0b00, MRSHPC_MW0CR2);
+ else
+ /* common mode & bus width 16bit SWAP = 0*/
+ __raw_writew(0x0300, MRSHPC_MW0CR2);
+
+ /* attribute window open */
+ __raw_writew(0x8a85, MRSHPC_MW1CR1);
+ if ((__raw_readw(MRSHPC_CSR) & 0x4000) != 0)
+ /* attribute mode & bus width 16bit SWAP = 1*/
+ __raw_writew(0x0a00, MRSHPC_MW1CR2);
+ else
+ /* attribute mode & bus width 16bit SWAP = 0*/
+ __raw_writew(0x0200, MRSHPC_MW1CR2);
+
+ /* I/O window open */
+ __raw_writew(0x8a86, MRSHPC_IOWCR1);
+ __raw_writew(0x0008, MRSHPC_CDCR); /* I/O card mode */
+ if ((__raw_readw(MRSHPC_CSR) & 0x4000) != 0)
+ __raw_writew(0x0a00, MRSHPC_IOWCR2); /* bus width 16bit SWAP = 1*/
+ else
+ __raw_writew(0x0200, MRSHPC_IOWCR2); /* bus width 16bit SWAP = 0*/
+
+ __raw_writew(0x2000, MRSHPC_ICR);
+ __raw_writeb(0x00, PA_MRSHPC_MW2 + 0x206);
+ __raw_writeb(0x42, PA_MRSHPC_MW2 + 0x200);
+}
+
+#endif /* __MACH_SE_MRSHPC_H */
obj-y += cpu/ timers/
obj-$(CONFIG_VSYSCALL) += vsyscall/
obj-$(CONFIG_SMP) += smp.o
-obj-$(CONFIG_CF_ENABLER) += cf-enabler.o
obj-$(CONFIG_SH_STANDARD_BIOS) += sh_bios.o
obj-$(CONFIG_KGDB) += kgdb.o
obj-$(CONFIG_SH_CPU_FREQ) += cpufreq.o
obj-y += cpu/ timers/
obj-$(CONFIG_VSYSCALL) += vsyscall/
obj-$(CONFIG_SMP) += smp.o
-obj-$(CONFIG_CF_ENABLER) += cf-enabler.o
obj-$(CONFIG_SH_STANDARD_BIOS) += sh_bios.o
obj-$(CONFIG_SH_CPU_FREQ) += cpufreq.o
obj-$(CONFIG_MODULES) += sh_ksyms_64.o module.o
+++ /dev/null
-/* $Id: cf-enabler.c,v 1.4 2004/02/22 22:44:36 kkojima Exp $
- *
- * linux/drivers/block/cf-enabler.c
- *
- * Copyright (C) 1999 Niibe Yutaka
- * Copyright (C) 2000 Toshiharu Nozawa
- * Copyright (C) 2001 A&D Co., Ltd.
- *
- * Enable the CF configuration.
- */
-
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/vmalloc.h>
-#include <linux/interrupt.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-
-/*
- * You can connect Compact Flash directly to the bus of SuperH.
- * This is the enabler for that.
- *
- * SIM: How generic is this really? It looks pretty board, or at
- * least SH sub-type, specific to me.
- * I know it doesn't work on the Overdrive!
- */
-
-/*
- * 0xB8000000 : Attribute
- * 0xB8001000 : Common Memory
- * 0xBA000000 : I/O
- */
-#if defined(CONFIG_CPU_SH4)
-/* SH4 can't access PCMCIA interface through P2 area.
- * we must remap it with appropriate attribute bit of the page set.
- * this part is based on Greg Banks' hd64465_ss.c implementation - Masahiro Abe */
-
-#if defined(CONFIG_CF_AREA6)
-#define slot_no 0
-#else
-#define slot_no 1
-#endif
-
-/* use this pointer to access to directly connected compact flash io area*/
-void *cf_io_base;
-
-static int __init allocate_cf_area(void)
-{
- pgprot_t prot;
- unsigned long paddrbase, psize;
-
- /* open I/O area window */
- paddrbase = virt_to_phys((void*)CONFIG_CF_BASE_ADDR);
- psize = PAGE_SIZE;
- prot = PAGE_KERNEL_PCC(slot_no, _PAGE_PCC_IO16);
- cf_io_base = p3_ioremap(paddrbase, psize, prot.pgprot);
- if (!cf_io_base) {
- printk("allocate_cf_area : can't open CF I/O window!\n");
- return -ENOMEM;
- }
-/* printk("p3_ioremap(paddr=0x%08lx, psize=0x%08lx, prot=0x%08lx)=0x%08lx\n",
- paddrbase, psize, prot.pgprot, cf_io_base);*/
-
- /* XXX : do we need attribute and common-memory area also? */
-
- return 0;
-}
-#endif
-
-static int __init cf_init_default(void)
-{
-/* You must have enabled the card, and set the level interrupt
- * before reaching this point. Possibly in boot ROM or boot loader.
- */
-#if defined(CONFIG_CPU_SH4)
- allocate_cf_area();
-#endif
-
- return 0;
-}
-
-#if defined(CONFIG_SH_SOLUTION_ENGINE)
-#include <mach-se/mach/se.h>
-#elif defined(CONFIG_SH_7722_SOLUTION_ENGINE)
-#include <mach-se/mach/se7722.h>
-#elif defined(CONFIG_SH_7721_SOLUTION_ENGINE)
-#include <mach-se/mach/se7721.h>
-#endif
-
-/*
- * SolutionEngine Seriese
- *
- * about MS770xSE
- * 0xB8400000 : Common Memory
- * 0xB8500000 : Attribute
- * 0xB8600000 : I/O
- *
- * about MS7722SE
- * 0xB0400000 : Common Memory
- * 0xB0500000 : Attribute
- * 0xB0600000 : I/O
- */
-
-#if defined(CONFIG_SH_SOLUTION_ENGINE) || \
- defined(CONFIG_SH_7722_SOLUTION_ENGINE) || \
- defined(CONFIG_SH_7721_SOLUTION_ENGINE)
-static int __init cf_init_se(void)
-{
- if ((ctrl_inw(MRSHPC_CSR) & 0x000c) != 0)
- return 0; /* Not detected */
-
- if ((ctrl_inw(MRSHPC_CSR) & 0x0080) == 0) {
- ctrl_outw(0x0674, MRSHPC_CPWCR); /* Card Vcc is 3.3v? */
- } else {
- ctrl_outw(0x0678, MRSHPC_CPWCR); /* Card Vcc is 5V */
- }
-
- /*
- * PC-Card window open
- * flag == COMMON/ATTRIBUTE/IO
- */
- /* common window open */
- ctrl_outw(0x8a84, MRSHPC_MW0CR1);
- if((ctrl_inw(MRSHPC_CSR) & 0x4000) != 0)
- /* common mode & bus width 16bit SWAP = 1*/
- ctrl_outw(0x0b00, MRSHPC_MW0CR2);
- else
- /* common mode & bus width 16bit SWAP = 0*/
- ctrl_outw(0x0300, MRSHPC_MW0CR2);
-
- /* attribute window open */
- ctrl_outw(0x8a85, MRSHPC_MW1CR1);
- if ((ctrl_inw(MRSHPC_CSR) & 0x4000) != 0)
- /* attribute mode & bus width 16bit SWAP = 1*/
- ctrl_outw(0x0a00, MRSHPC_MW1CR2);
- else
- /* attribute mode & bus width 16bit SWAP = 0*/
- ctrl_outw(0x0200, MRSHPC_MW1CR2);
-
- /* I/O window open */
- ctrl_outw(0x8a86, MRSHPC_IOWCR1);
- ctrl_outw(0x0008, MRSHPC_CDCR); /* I/O card mode */
- if ((ctrl_inw(MRSHPC_CSR) & 0x4000) != 0)
- ctrl_outw(0x0a00, MRSHPC_IOWCR2); /* bus width 16bit SWAP = 1*/
- else
- ctrl_outw(0x0200, MRSHPC_IOWCR2); /* bus width 16bit SWAP = 0*/
-
- ctrl_outw(0x2000, MRSHPC_ICR);
- ctrl_outb(0x00, PA_MRSHPC_MW2 + 0x206);
- ctrl_outb(0x42, PA_MRSHPC_MW2 + 0x200);
- return 0;
-}
-#else
-static int __init cf_init_se(void)
-{
- return -1;
-}
-#endif
-
-static int __init cf_init(void)
-{
- if (mach_is_se() || mach_is_7722se() || mach_is_7721se())
- return cf_init_se();
-
- return cf_init_default();
-}
-
-__initcall (cf_init);
projects / linux-2.6-omap-h63xx.git / commitdiff